Coffee and mineral oil hydrocarbons: potential dietary intake.

Levels of mineral oil hydrocarbons were measured in a large range of green and roasted coffee beans or ground powder. To better understand the consumer exposure to mineral oil hydrocarbons, the transfer to the brewed coffee was assessed under three different preparations. As a result, less than 5% of mineral oil hydrocarbons were transferred to the cup. With this low transfer rate, the coffee contribution to the mineral oils daily intake can be assessed to be very low, below 0.8% of the total exposure.

Comparison of carrier gases for the separation and quantification of mineral oil hydrocarbon (MOH) fractions using online coupled high performance liquid chromatography-gas chromatography-flame ionisation detection.

On-line coupled high performance liquid chromatography-gas chromatography-flame ionisation detection (HPLC-GC-FID) was used to compare the effect of hydrogen, helium and nitrogen as carrier gases on the chromatographic characteristics for the quantification of mineral oil hydrocarbon (MOH) traces in food related matrices. After optimisation of chromatographic parameters nitrogen carrier gas exhibited characteristics equivalent to hydrogen and helium regarding requirements set by current guidelines and standardisation such as linear range, quantification limit and carry over. Though nitrogen expectedly led to greater peak widths, all required separations of standard compounds were sufficient and humps of saturated mineral oil hydrocarbons (MOSH) and aromatic mineral oil hydrocarbons (MOAH) were appropriate to enable quantitation similar to situations where hydrogen or helium had been used. Slightly increased peak widths of individual hump components did not affect shapes and widths of the MOSH and MOAH humps were not significantly affected by the use of nitrogen as carrier gas. Notably, nitrogen carrier gas led to less solvent peak tailing and smaller baseline offset. Overall, nitrogen may be regarded as viable alternative to hydrogen or helium and may even extend the range of quantifiable compounds to highly volatile hydrocarbon eluting directly after the solvent peak.

A Study on Mineral Oil Hydrocarbons (MOH) Contamination in Pig Diets and Its Transfer to Back Fat and Loin Tissues.

This study assessed saturated mineral oil hydrocarbons (MOSH) and aromatic mineral oil hydrocarbons (MOAH) levels in grower-finisher feeds for pigs supplemented with 5% crude palm oil (CP), crude olive pomace oil (COP), olive pomace acid oil (OPA), or a blend of CP and OPA (50:50, w/w); the contribution of the lipid source to that contamination; and the ability of pigs to accumulate MOH in back fat and loin tissues after 60 days of trial. MOSH and MOAH were analyzed with liquid chromatography (LC)-gas chromatography (GC)-flame ionization detection (FID) after sample preparation. Among the lipid sources, CP had the lowest MOH levels, but CP feeds showed the highest contamination. This, along with the different MOSH profiles, indicated the presence of more significant contamination sources in the feeds than the lipid source. The higher MOH contamination in CP feeds was reflected in the highest MOSH levels in pig back fat, whereas MOAH were not detected in animal tissues. Also, MOSH bioaccumulation in pig tissues was influenced by the carbon chain length. In conclusion, feed manufacturing processes can determine the MOSH contamination present in animal adipose tissues that can be included in human diets.

Update of the risk assessment of mineral oil hydrocarbons in food.

Mineral oil hydrocarbons (MOH) are composed of saturated hydrocarbons (MOSH) and aromatic hydrocarbons (MOAH). Due to the complexity of the MOH composition, their complete chemical characterisation is not possible. MOSH accumulation is observed in various tissues, with species-specific differences. Formation of liver epithelioid lipogranulomas and inflammation, as well as increased liver and spleen weights, are observed in Fischer 344 (F344) rats, but not in Sprague-Dawley (SD) rats. These effects are related to specific accumulation of wax components in the liver of F344 rats, which is not observed in SD rats or humans. The CONTAM Panel concluded that F344 rats are not an appropriate model for effects of MOSH with wax components. A NOAEL of 236 mg/kg body weight (bw) per day, corresponding to the highest tested dose in F344 rats of a white mineral oil product virtually free of wax components, was selected as relevant reference point (RP). The highest dietary exposure to MOSH was estimated for the young population, with lower bound-upper bound (LB-UB) means and 95th percentiles of 0.085-0.126 and 0.157-0.212 mg/kg bw per day, respectively. Considering a margin of exposure approach, the Panel concluded that the present dietary exposure to MOSH does not raise concern for human health for all age classes. Genotoxicity and carcinogenicity are associated with MOAH with three or more aromatic rings. For this subfraction, a surrogate RP of 0.49 mg/kg bw per day, calculated from data on eight polycyclic aromatic hydrocarbons, was considered. The highest dietary exposure to MOAH was also in the young population, with LB-UB mean and 95th percentile estimations of 0.003-0.031 and 0.011-0.059 mg/kg bw per day, respectively. Based on two scenarios on three or more ring MOAH contents in the diet and lacking toxicological information on effects of 1 and 2 ring MOAH, a possible concern for human health was raised.

Review on chromatographic and specific detection methodologies for unravelling the complexity of MOAH in foods.

Contamination of foods with mineral oil hydrocarbons, particularly mineral oil aromatic hydrocarbons (MOAH), can potentially pose a health hazard to consumers. However, identifying toxic substances among the many thousands of compounds comprising mineral oils in food samples is a difficult analytical challenge. According to the European Food Safety Authority, there is a lack of concentration and structural data about mineral oil hydrocarbons in foods, and therefore it is not clear to what extent consumers in Europe might be exposed to toxic levels of MOAH. The current gold standard method for determination of mineral oil hydrocarbons is online high-performance liquid chromatography (LC)-gas chromatography (GC) with flame ionization detection, which quantifies total saturated/aromatic content, but gives no qualitative information. The objective of this review is to explore the future prospects in mineral oil hydrocarbon determination and MOAH characterization in foods. To that end, peer reviewed literature was explored, particularly from the viewpoint of a methodology for detailed characterization of the MOAH fraction that can aid toxicological assessment. The literature clearly shows that there is much to be gained from the orthogonality power of multidimensional chromatographic separations and mass spectrometric (MS) detection. Comprehensive two-dimensional GC coupled to MS, preceded by pre-fractionations of MOAH by LC is suggested to be the most promising approach for further research. In addition, the strengths and weaknesses of a number of other, alternative approaches, both for qualitative and quantitative analysis, are discussed.

Implications of a Diabetic Foot Xerosis Treatment With an Emulsion Containing the Plant-Based Anionic Phospholipids.

PURPOSE: This study compares and contrasts a skin cream containing plant-based anionic polar phospholipid (APP) technology with a mineral oil hydrocarbon (petrolatum)-based (MHB) skin cream technology in the treatment of skin xerosis (dryness) in diabetic feet. Skin cream with APP technology promotes phospholipid absorption, reparation of intercellular lamellae, and organization of water promoting hydration; whereas skin cream with mineral hydrocarbon-based (MHB) technology principally covers skin, preventing dehydration. METHODS: Subjects (n = 54) with diagnoses of diabetes mellitus and foot skin dryness were studied using a multicenter, double-blind, masked-study design. An emulsion cream containing 0.05% APP in triglycerides (APP preparation) was compared to MHB skin cream, Eucerin® (MHB preparation) applied topically to skin of the feet. Graded measurements were recorded on 4 efficacy variables including dryness, erythema, fissures, and itching and neurovascular assessments. Implications of the plant-based and mineral-based skin creams in the context of skin xerosis are contrasted. RESULTS: APP and MHB preparations were similar in effectiveness and safety. There was no significant difference among any of the 4 efficacy variables (P < .5) including neurovascular measurements. The APP preparation is absorbed into the skin, whereas the MHB skin cream leaves detectable residues after each application. CONCLUSION: Although the APP and MHB preparations were not significantly different in effectiveness and safety, distinctively, application of the APP skin cream preparation absorbed into the skin leaving no discernible residue in contrast to the MHB preparation leaving residues potentiating textile damage. Both of these technologies function in the hydration of skin; however, they differ in their modes of action. The plant-based APP preparation functions actively by phospholipid and triglyceride absorption, reparation of skin lamellae, and in the consequent delivery and organization of waters of hydration in skin. The MHB preparation functions passively, hydrating the skin it covers by sealing the skin against dehydration.

Biscuit Contaminants, Their Sources and Mitigation Strategies: A Review.

The scientific literature is rich in investigations on the presence of various contaminants in biscuits, and of articles aimed at proposing innovative solutions for their control and prevention. However, the relevant information remains fragmented. Therefore, the objective of this work was to review the current state of the scientific literature on the possible contaminants of biscuits, considering physical, chemical, and biological hazards, and making a critical analysis of the solutions to reduce such contaminations. The raw materials are primary contributors of a wide series of contaminants. The successive processing steps and machinery must be monitored as well, because if they cannot improve the initial safety condition, they could worsen it. The most effective mitigation strategies involve product reformulation, and the use of alternative baking technologies to minimize the thermal load. Low oxygen permeable packaging materials (avoiding direct contact with recycled ones), and reformulation are effective for limiting the increase of contaminations during biscuit storage. Continuous monitoring of raw materials, intermediates, finished products, and processing conditions are therefore essential not only to meet current regulatory restrictions but also to achieve the aim of banning dietary contaminants and coping with related diseases.

Occurrence of Mineral Oil Hydrocarbons in Omega-3 Fatty Acid Dietary Supplements.

Omega-3 fatty acid dietary supplements have become increasingly popular with consumers due to their multiple health benefits. In this study, the presence of mineral oil hydrocarbons (MOH) was investigated in seventeen commercial samples of such supplements, characterized by different formulations. The analyses were performed using on-line liquid chromatography-gas chromatography (with flame ionization detection), which is considered the most efficient method for the determination of MOH in foodstuffs. Analyte transfer was performed by using the retention gap technique, with partially concurrent solvent evaporation. Various degrees of mineral oil saturated hydrocarbon contamination (from 2.4 ppm to 375.7 ppm) were found, with an average value of 49.9 ppm. Different C-number range contaminations were determined, with the >C25-≤C35 range always found with an average value of 26.9 ppm. All samples resulted free of mineral oil aromatic hydrocarbons, except for two samples in which a contamination was found at the 9.9 and 6.6 ppm levels, respectively.

Use of a low-cost, lab-made Y-interface for liquid-gas chromatography coupling for the analysis of mineral oils in food samples.

Consumers are daily exposed to a range of mineral oil hydrocarbons via food consumption. Major sources of MOH in food are packaging and additives, processing aids, and lubricants. In 2019, an EU guidance was released covering specific directions for sampling and analysis of mineral oil saturated hydrocarbons (MOSH) and mineral oil aromatic hydrocarbons (MOAH) in food and food contact materials within the frame of Recommendation (EU) 2017/84 for the monitoring of mineral oils. The parameters required by the guide are increasingly stringent, and coping with this type of analysis is now very challenging. It is within such a context that the present research is confined, inasmuch that it is focused on the construction of a low-cost, lab-made Y-interface for liquid-gas chromatography coupling used for the determination of MOSH and MOAH in foodstuffs. The response ratios of alkanes comprised between C10 and C50 were measured and were comprised between 0.9 and 1.1, with a maximum coefficient of variation of 4% (n = 5). Intermediate precision was evaluated for the fat/oil category during a period of 48 days obtaining a value of 10%. Qualitative and quantitative analysis of both MOSH and MOAH were performed in a single run and in a fully-automated manner. Seventeen different foods were analyzed in order to cover the categories reported in the EU guide. Saturated hydrocarbon contamination was detected only in a few samples (in the range 1-153 ppm); MOAH contamination was found only in one sample (sunflower oil: 15 ppm).

Dietary exposure to mineral oil hydrocarbons of Chinese infants aged 0-6 months.

Consumers are exposed to a range of mineral oil hydrocarbons (MOH) via food. The potential adverse health effect of MOH varies widely. Since infant formula (IF) is the major food source for infants, it is necessary to understand MOH exposure and consequent health impact. In the present study, occurrence data of 42 IF samples and food consumption data of 0-6 months infants from China National Food Consumption Survey in 2015 were linked to evaluate the dietary exposure to MOH of 0-6 months infants in China. Ordinary consumers (who purchased IF for 0-6 months infants in different packaging type randomly), packaging type loyal- and brand loyal-consumers were selected as three representative populations. For ordinary consumers and packaging-loyal consumers, dietary exposure to MOH was estimated both deterministically and probabilistically. For brand-loyal consumers, point-estimation was used as the exposure assessment method. Due to toxicological gaps for MOHs, it was inappropriate to derive health-based guidance value and perform the robust human health risk assessment. MOE approach was used to characterise MOSH risk. The no-observed-adverse-effect level for induction of liver microgranulomas, 19 mg/kg BW per day, was used as a reference point for calculating margins of exposure (MOEs) for MOSH exposure. Although first exposure occurs in babies, there are no relevant toxicology studies. All MOE values for different scenarios were higher than 100. There are no dose-response data on the carcinogenicity of MOAH mixtures and hence it is not possible to establish a reference point to calculate the MOE and characterise its risk. Therefore, it is not possible to draw conclusions about the full nature of possible concerns for infants aged 0-6 months. This study evaluates by a probabilistic approach the dietary intake of Chinese infants aged 0-6 months to MOH for the first time and describes the associated uncertainties.

Comparison of the Functional Barrier Properties of Chitosan Acetate Films with Conventionally Applied Polymers.

The current demand to cut back on the use of plastic materials has brought a major boost to the search for bio-based alternatives. Not only are plastic bags and primary food packaging under scrutiny here, but also those materials used as functional barriers to reduce, for example, the migration of mineral oil hydrocarbons (MOH) from recycled paper and board packaging. Most of the barriers now in use are synthetic, often have only moderate barrier functionalities and in addition reduce the environmentally-friendly character of cellulose-based materials. Against this background, bio-based polymers have been evaluated in terms of their functional barrier properties. Chitosan was found to be among the best performers in these materials. In this study, the behavior of a lab-made chitosan acetate film was compared with conventionally produced polymer films. The two-sided migration experiment described recently was used to determine the barrier properties of the tested materials. This not only allowed to test the intrinsic migration of the films and the permeation through them, but also to simulate real packaging situations by using a recycled paper as donor for MOH. The migrated fractions were determined using gas-chromatography-based techniques. While the conventionally produced polymer films showed only moderate barrier function, excellent results were seen for the biopolymer. It reduced the migration from the recycled paper to not detectable, singling it out as a good alternative to conventional materials.

Mild mixed-solvent extraction for determination of total mineral oil hydrocarbon contaminants in milk powder products.

A mild mixed-solvent of n-hexane/isopropanol is proposed for extracting total mineral oil hydrocarbons (MOH) from commercial milk powder products. Unlike acid-hydrolysis, the mixed-solvent extraction was performed at ambient temperature and the low-boiling-point hydrocarbons were retained to the greatest extent. After extraction, total MOH was determined by on-line liquid chromatography-gas chromatography with a flame ionization detector (LC-GC-FID). The validation of the proposed extraction method revealed a recovery efficacy of 83.0-107.5% and a limit of quantification of 0.5 mg/kg. Then, the total MOH in ten commercial milk powders was determined and mineral oil saturated hydrocarbons (MOSH)/polyolefin oligomeric saturated hydrocarbons (POSH) were found to be within the range of 0.61-5.46 mg/kg. The comparison of the total and surface MOSH/POSH indicated that a major part of the contamination was derived from sources before packaging. The present study provides a robust method for the extraction and determination of total MOH in milk powders.

Potential for short-term migration of mineral oil hydrocarbons from coated and uncoated food contact paper and board into a fatty food simulant.

Mineral oil hydrocarbons (MOH) are widely used in the food industry for applications such as printing inks, additives, adhesives, and processing aids for food additives. Recently, the migration of MOH from food contact paper and board into foods has raised public health concerns. In this study, a total of 110 food contact paper and board samples, including baking and cooking paper (23), baking cups (28), food packaging bags (22), lunch boxes (8), party plates (26), and straws (3) were evaluated to quantify the content and short-term migration levels of MOH. The MOH were separated into mineral oil saturated hydrocarbons (MOSH)/polyolefin oligomeric saturated hydrocarbons (POSH) and mineral oil aromatic hydrocarbons (MOAH) via a validated on-line liquid chromatography-gas chromatography-flame ionisation detection (LC-GC-FID) technique. The coating materials of the sample products comprised polyethylene, polypropylene, polyethylene terephthalate, and silicone. The effects of the coating materials on the content and migration of MOH/POSH were evaluated. Quantitative analysis of the MOH in the samples showed that the MOSH/POSH and MOAH content varied widely, ranging from 16 to 5626 mg kg-1 for MOH, regardless of the coating materials. Short-term migration of MOSH/POSH was observed only in samples with polyolefinic coatings, such as polyethylene and polypropylene, in experiments conducted at 25 °C for 10 min, although the extent of MOAH migration for all samples was at the trace level. The migration of MOSH/POSH was detected within the range of 0.93 to 62.3 µg L-1 in 22 samples, and the migration of MOAH was detected within the range of 0.80 to 2.6 µg L-1 in only 4 samples. These results demonstrate that although the short-term migration potential of MOH is generally negligible, the migration of MOSH/POSH into wet fatty foods can be accelerated by polyolefinic coatings, even within a very short time.

Evaluating the risk to humans from mineral oils in foods: Current state of the evidence.

Key issues around the evaluation of risks to humans from mineral oils in food and feedstuffs are discussed. MOHs (MOAH and MOSH) occur in food due to intentional use, contamination from environmental sources and during transport/processing, or through migration from food contact materials. Problems in setting and enforcing human health guidelines for MOH include uncertainty around MOH toxicity and the specialist expertise needed for analysis of complex food matrices. Currently, the method of choice for measuring mineral oils is LC-GC-FID, however some complex food matrices also require additional analytical techniques to differentiate between some naturally occurring hydrocarbons and those from other sources, including of petrogenic origin. This requires the skills of an experienced analyst. Significant toxicological gaps for MOHs prevent robust human health risk assessment and the derivation of guidance values. As food-grade mineral oils are virtually MOAH-free, the key issue explored here is the relevance to humans of liver (micro)granulomas observed in F344 rats following oral intake. Available data suggest that despite the ubiquitous nature of MOH in the human diet, the prevalence of liver lipogranulomas in the population is low. These are not associated with inflammation and based on current evidence are not considered of human health significance.

Microwave-Based Technique for Fast and Reliable Extraction of Organic Contaminants from Food, with a Special Focus on Hydrocarbon Contaminants.

Due to food complexity and the low amount at which contaminants are usually present in food, their analytical determination can be particularly challenging. Conventional sample preparation methods making use of large solvent volumes and involving intensive sample manipulation can lead to sample contamination or losses of analytes. To overcome the disadvantages of conventional sample preparation, many researchers put their efforts toward the development of rapid and environmental-friendly methods, minimizing solvent consumption. In this context, microwave-assisted-extraction (MAE) has obtained, over the last years, increasing attention from analytical chemists and it has been successfully utilized for the extraction of various contaminants from different foods. In the first part of this review, an updated overview of the microwave-based extraction technique used for rapid and efficient extraction of organic contaminants from food is given. The principle of the technique, a description of available instrumentation, optimization of parameters affecting the extraction yield, as well as integrated techniques for further purification/enrichment prior to the analytical determination, are illustrated. In the second part of the review, the latest applications concerning the use of microwave energy for the determination of hydrocarbon contaminants-namely polycyclic aromatic hydrocarbons (PAHs) and mineral oil hydrocarbons (MOH)-are reported and critically overviewed and future trends are delineated.

Characterization of natural polymers as functional barriers for cellulose-based packaging materials.

Cellulose-based packaging materials are currently the most commonly used food packaging materials due to their light weight, stability and affordable price. However, the use of recycled paper and board adds to the risk that undesirable substances migrate into the packed goods, since contaminants are not completely removed during the recycling process and can accumulate in the final product. The only available fast and practical solution that can be used to reduce the migration of these substances is the application of functional barriers in the packaging. The applied barriers are currently mostly synthetic, which either serve only a moderate barrier function and/or have the disadvantage that it is often more complex and expensive to recycle the resulting packaging material. The aim of this project is to evaluate different bio-based or biodegradable polymers with regards to their barrier properties. Due to the fact that the transport phenomena are mainly driven by (gas phase) migration, methods based on gas chromatography (GC), including GC coupled with mass spectrometry (GC-MS) and flame ionization detection (GC-FID), GC-FID coupled online with high pressure liquid chromatography (HPLC-GC-FID), and comprehensive GCxGC-MS were used to qualify and quantify the migrated substances. This use of a wide range of different methods and instruments yielded excellent results, allowing us to comprehensively characterize the biopolymers and their barrier function.

Screening for mineral oil saturated and aromatic hydrocarbons in paper and cardboard directly by planar solid phase extraction and by its coupling to gas chromatography.

Mineral oil saturated and aromatic hydrocarbons (MOSH/MOAH) are food contaminants, mainly due migration from packaging materials made from recycled fibers, but other routes of entry into food have also been identified. Legal limits for MOSH and MOAH in food and food contact materials currently are not set, but are to be expected in the near future. For the analysis of MOSH and MOAH, the very well developed and highly automated on-line liquid chromatography-gas chromatography with flame ionization detection (LC-GC-FID) is commonly used. However, this approach is time-consuming, and data interpretation is a very challenging task. Therefore, a planar solid phase extraction (pSPE) method was developed for a rapid and efficient MOSH and MOAH screening in paper and cardboard. Based on high-performance thin-layer chromatography (HPTLC), pSPE offers the simultaneous clean-up and analysis of up to 20 samples in parallel, while MOSH and MOAH analytes were focused in two distinct target zones on silica gel HPTLC plates after a twofold development. Plate impregnation with primuline allowed the detection of MOSH by fluorescence, while MOAH were detected by UV light absorption. The pSPE screening approach provided limits of detection of 7.2 and 2.3 ng/zone for MOSH and MOAH, respectively, corresponding to 1.8 and 0.6 mg/kg paper. Coupling of pSPE with GC revealed the common MOSH and MOAH peak humps, while marker substances offered the identification of the mineral oil origin or information about recycled fiber materials. As compared to SPE-GC-FID analyses, the determined quantities of MOSH and MOAH in cardboard samples indicated pSPE as a rapid and suitable screening tool. The co-migration of polyolefin oligomeric saturated hydrocarbons, native n-alkanes, terpenes and possibly essential oils or sterol esters, however, can result in an overestimation of MOSH and MOAH. Hence, samples with pSPE results above a given limit are subsequently analyzed by GC (pSPE-GC) for confirmation and detailed evaluation.

Effect of dietary pristane and other saturated mineral oils (MOSH) on autoimmune arthritis in rats.

Pristane and other adjuvants based on mineral oil saturated hydrocarbons (MOSH) may induce autoimmunity in rodents after intradermal injection; however there is a lack of information on immune effects after oral MOSH exposure. The aim of our study was to determine the impact of dietary exposure to pristane and other MOSH on the development of autoimmune arthritis. Dark Agouti (DA) rats were given feed containing 4000 mg/kg pristane or a broad MOSH mixture in various concentrations (0-4000 mg/kg) for 90 days, or a single intradermal injection of 200 µl pristane (positive control). Arthritis scores, and serum and splenocyte markers previously associated with arthritis development, were determined. All rats injected with pristane displayed arthritis symptoms and higher levels of certain serum markers. None of the rats fed pristane or MOSH developed arthritis symptoms or demonstrated clear changes in any measured arthritis-associated biological markers in serum or splenocytes. The absence of clinical arthritis symptoms or any increase in common arthritis-associated biological markers in sera and spleen following dietary exposure to pristane or a broad MOSH mixture in a sub-chronic rat model of arthritis suggest that dietary MOSH have low capacity to promote development of autoimmunity.

Analysis of saturated and aromatic hydrocarbons migrating from a polyolefin-based hot-melt adhesive into food.

Hot-melt adhesives are widely utilised to glue cardboard boxes used as food packaging material. They have to comply with the requirements of Article 3 of the European Framework Regulation for food contact materials (1935/2004). The hot melt raw materials analysed mainly consisted of paraffinic waxes, hydrocarbon resins and polyolefins. The hydrocarbon resins, functioning as tackifiers, were the predominant source of hydrocarbons of sufficient volatility to migrate into dry foods: the 18 hydrocarbon resins analysed contained 8.2-118 g kg(-1) saturated and up to 59 g kg(-1) aromatic hydrocarbons eluted from GC between n-C16 and n-C24, substantially more than the paraffinic waxes and the polyolefins. These tackfier resins, especially the oligomers ≤ C24, have been characterised structurally by GC×GC-MS and (1)H-NMR spectroscopy. Migration into food was estimated using a simulating system with polenta as food simulant, which was verified by the analysis of a commercial risotto rice sample packed in a virgin fibre folding box sealed with a hot melt. About 0.5-1.5% of the potentially migrating substances (between n-C16 and n-C24) of a hot melt were found to be transferred into food under storage conditions, which can result in a food contamination in the order of 1 mg kg(-1) food (depending on the amount of potentially migrating substances from the hot melt, the hot melt surface, amount of food, contact time etc.). Migrates from hot melts are easily mistaken for mineral oil hydrocarbons from recycled cardboard.