On the evaluation of surface tension of biodiesel.

Over time, with the increase in population and the subsequent increase in energy consumption and also due to the non-renewability of fossil fuels, the study of alternative fuels has increased. One of these fuels is biodiesel, which is a suitable alternative to fossil fuels such as diesel and received much attention from researchers today. For this reason, measuring the physical properties of biodiesel is of great importance. Due to the high cost and time-consuming nature of laboratory methods, numerical methods are used to estimate material properties. The novelty of this research was the use of two white box models, including Group method of data handling (GMDH) and Gene expression programming (GEP), which work on the basis of artificial intelligence. By using these models, two simple mathematical equations with high accuracy were presented to predict the surface tension of biodiesel. These models can be used at different temperatures and molecular weights. To do modeling, 78 laboratory data available in the literature were gathered and the data were randomly divided into two groups, train and test, in a ratio of 80 and 20. The input parameters include mass fraction of fatty acid ethyl esters and temperature (T), and esters are divided into three groups according to their molecular weight: less than 200 (Mw1), between 200 and 300 (Mw2), and greater than 300 (Mw3). The statistical error parameters were calculated for the two models developed in this research and after comparing the results, it was found that the GMDH model estimates the surface tension of biodiesel with a higher accuracy. The average absolute relative error for GMDH and GEP models was reported as 0.97 and 1.89, respectively. Also, other statistical error parameters of GMDH such as RMSE, SD, and R2 for the GMDH model were obtained as 0.444, 0.000233, and 0.9233, respectively. Moreover, sensitivity analysis showed that temperature has the highest impact on the surface tension of biodiesel, which is also an inverse effect. Finally, suspicious laboratory and outlier data points were identified using the Leverage technique. According to this analysis, only five data points were identified as outliers and suspicious laboratory data.

On the temperature dependence of surface tension: Historical perspective on the Eötvös equation of capillarity, celebrating his 175th anniversary.

The Hungarian baron Roland Eötvös (Eötvös Loránd, 1848-1919) lived in the difficult period between two revolutions in Hungary, but nevertheless he achieved revolutionary results in two fields of science: capillarity (1875-1886) and gravity (after 1886). This paper describes his famous capillary equation published in 1886 in the world-language of the time (German) and in one of the most famous scientific journals of the time (Annalen der Physik und Chemie). In his paper he showed a simple equation for the temperature dependence of surface tension of one-component liquids and more importantly he showed that this quantity approaches zero as temperature tends towards the critical temperature. This result was achieved by measuring the surface tension of 160 (!) different liquids along their boiling lines as function of temperature, in a home-made high-pressure high-temperature equipment, probably the first one of this kind. In this way he extended the meaning of the critical point previously introduced by van der Waals. In this paper, also a modern model of surface tension of one-component liquids is discussed, simplified and compared to the Eötvös equation. It is also shown, how the Avogadro number and the molecular sizes can be determined from the experimental results of Eötvös (note: the Avogadro number was estimated with reasonable accuracy for the first time by Einstein in 1905 from the kinetic theory of liquids). Apparently, it was not that easy to do back in 1886: this becomes obvious from the 1911-paper by Einstein, who gave a wrong estimate for the diameter of Hg atoms (5.19 nm) using the data of Eötvös (the correct value is around 0.3 nm). The Appendix to this paper contains the summary of 1543 handwritten pages on surface tension by Eötvös, including the on-line availability of all pdf files. Note also, that Eötvös used g = 10.0 m/s2 for acceleration due gravity and so he over-estimated his surface tension values and also his Eötvös constant by about 2.0%. The corrected Eötvös constant using his measured values but the correct g-value would be "0.222" vs his published value of "0.227". Probably this uncertainty in the value of g was one of the motives that pushed Eötvös to study gravity after 1886.

Polyhedral Vinyl Polymer Particles Synthesized Via Solvent-Free Radical Polymerization.

Liquid marbles (LMs) with a cubic shape are created by using various vinyl monomers as an inner liquid and polymer plates with mm size as a stabilizer. The relationship between the surface tension of the vinyl monomers and formability of the LMs is investigated. LMs can be fabricated using vinyl monomers with surface tensions of 42.7-40.3 mN m-1. The cubic polymer particles are successively synthesized via free-radical polymerizations by irradiation of the cubic LMs with UV light in a solvent-free manner. In addition, controlling the number of polymer plates per one LM, the shape of the plate or the coalescence of the LMs can lead to production of polymer particles with desired forms (e.g., Platonic and rectangular solids) that correspond to the shapes of the original LMs.

Compatibility of Dual Rinse 1-Hydroxyethane-1,1-Diphosphonic Acid with Sodium Hypochlorite Solutions Containing Proprietary Additives.

INTRODUCTION: A salt of 1-hydroxyethylidene-1,1-diphosphonic acid (HEDP) was commercialized some years ago. This so-called Dual Rinse (DR) HEDP has been tested for its combined actions and interactions with pure sodium hypochlorite (NaOCl) solutions. The aim of this study was to assess DR interactions with NaOCl solutions containing proprietary additives. METHODS: Designated endodontic NaOCl solutions that come at 2 different strengths (2% and 5.25%), and without or with additives (Chloraxid and Chloraxid Extra, respectively) were tested. Some of their key chemical and physical properties were determined in the presence or absence of HEDP (9%) in the solution. In addition, soft tissue dissolution efficacy of test and control solutions was assessed in extracted teeth (n = 10 per group, 90 teeth in total). RESULTS: The NaOCl content in the 2% Chloraxid solutions was slightly above, that in the 5.25% solutions below the labeled concentration. The additives in the Chloraxid Extra solutions neither altered their surface tension nor their viscosity. The addition of HEDP to any of the tested NaOCl solutions reduced their pH, and increased their surface tension and viscosity. HEDP-induced available chlorine loss over the first hour was similar between all NaOCl solutions. Soft tissue dissolution in the root canals was affected by NaOCl concentration, but neither by any proprietary NaOCl additive in the Chloraxid solutions, nor the addition of DR HEDP. CONCLUSIONS: Proprietary additives had no influence on any of the tested parameters, including surface tension of the "Extra" solutions. The increased viscosity of combined NaOCl/HEDP solutions deserves further attention.

Interfacial protein adsorption behavior can be connected across a wide range of timescales using the microfluidic EDGE (Edge-based droplet GEneration) tensiometer.

HYPOTHESIS: Our hypothesis is that dynamic interfacial tension values as measured by the partitioned-Edge-based Droplet GEneration (EDGE) tensiometry can be connected to those obtained with classical techniques, such as the automated drop tensiometer (ADT), expanding the range of timescales towards very short ones. EXPERIMENTS: Oil-water and air-water interfaces are studied, with whey protein isolate solutions (WPI, 2.5 - 10 wt%) as the continuous phase. The dispersed phase consists of pure hexadecane or air. The EDGE tensiometer and ADT are used to measure the interfacial (surface) tension at various timescales. A comparative assessment is carried out to identify differences between protein concentrations as well as between oil-water and air-water interfaces. FINDINGS: The EDGE tensiometer can measure at timescales down to a few milliseconds and up to around 10 s, while the ADT provides dynamic interfacial tension values after at least one second from droplet injection and typically is used to also cover hours. The interfacial tension values measured with both techniques exhibit overlap, implying that the techniques provide consistent and complementary information. Unlike the ADT, the EDGE tensiometer distinguishes differences in protein adsorption dynamics at protein concentrations as high as 10 wt% (which is the highest concentration tested) at both oil-water and air-water interfaces.

In Situ Multi-Directional Liquid Manipulation Enabled by 3D Asymmetric Fang-Structured Surface.

Decorating surfaces with wetting gradients or topological structures is a prevailing strategy to control uni-directional spreading without energy input. However, current methods, limited by fixed design, cannot achieve multi-directional control of liquids, posing challenges to practical applications. Here, a structured surface composed of arrayed three-dimensional asymmetric fang-structured units is reported that enable in situ control of customized multi-directional spreading for different surface tension liquids, exhibiting five novel modes. This is attributed to bottom-up distributed multi-curvature features of surface units, which create varied Laplace pressure gradients to guide the spreading of different-wettability liquids along specific directions. The surface's capability to respond to liquid properties for multimodal control leads to innovative functions that are absent in conventional structured surfaces. Selective multi-path circuits can be constructed by taking advantage of rich liquid behaviors with the surface; surface tensions of wetting liquids can be portably indicated with a resolution scope of 0.3-3.4 mN m-1 using the surface; temperature-mediated change of liquid properties is utilized to smartly manipulate liquid behavior and achieve the spatiotemporal-controllable targeted cooling of the surface at its heated state. These novel applications open new avenues for developing advanced surfaces for liquid manipulation.

Physical properties of soft contact lens multipurpose solutions commercially available in Ghana.

Purpose: To investigate the physical properties of commercially available multipurpose soft contact lens solutions in Ghana. Methods: pH (Kelilong ICL-099 pH meter, China), osmolality (OSMOMAT 3000, GONOTEC, Germany), surface tension (Sigma 700 Tensiometer, Sweden), and viscosity (CFOC-200 Viscometer, Cannon Company, USA) of various soft contact lens multipurpose solutions (MPS) were measured in triplicates at room temperature. Viscosity measurements were also taken at 34 °C ocular surface temperature. The solutions examined were Opti-Free Replenish (OFR), Trufresh (TF), Avizor (AV), Freshlook (FL), and Refresh (RF). Results: Several solutions were largely hypo-osmotic in the range of 108-231 mOsm/kg, the exception being Avizor, which had osmolality values that were closer to human tears (301 ± 0.58 mOsm/kg). The range of pH values of the solutions (6.33-8.24, mean (SD) = 7.53 ± 0.18) fell within the reported tolerable range for the ocular surface (6.20-9.00). Surface tension values ranged from 35.86 to 42.27 mNm with a mean of 38.49 ± 2.32 mNm. The average viscosity of most solutions at room temperature (25 °C) was 1.44 ± 0.49 cP with a range of 1.04-2.15 cP. Significantly lower values ranging from 0.79 to 1.58 cP were obtained at ocular surface temperature (34 °C), p = 0.0001). Conclusions: The physical properties of many of the solutions used as MPS in Ghana are markedly variable. Nevertheless, pH, surface tension, and viscosity fall within the acceptable limits of ocular physiological tolerance; except for osmolality, which majority were outside the reported tolerable range for the ocular surface. This information may partly explain the reason some patients exhibit strong preferences for certain care systems and should aid clinical decision-making when prescribing eye care systems to patients.

Sand washing of oil spill-affected beaches using concentrated ß-glucans obtained from residual baker's yeast.

Valorization of residual yeast of the bakery industry for use in the remediation of oil-contaminated soils as an emulsifier is a biocompatible and effective process that will reduce environmental pollution. The aim of this study was to use concentrated ß-glucan obtained from residual baker's yeast, Saccharomyces cerevisiae, as an emulsifier to remove total petroleum hydrocarbons (TPH) from the contaminated sands of two beaches affected by the oil spill that occurred in January 2022 north of Lima, Peru. The extraction and concentration of ß-glucan from sand were performed at a pilot scale using autolysis with 3 % sodium chloride, temperature elevation, treatment with organic solvents and water, hydrolysis via proteases, and vacuum filtration. The chemical composition and functional properties of concentrated ß-glucan were evaluated to determine its quality and efficacy. In addition, the values of TPH removal efficiency obtained using concentrated ß-glucan, water, and the commercial emulsifier Tween-80 were compared. The mass recovery of concentrated ß-glucan was 5.59 %, with a ß-glucan content of 38.60 %. The efficiency of ex-situ removal of TPH from hydrocarbon-impacted sands containing 78323 mg/kg of TPH reached 50 % and 70 % when the concentrated ß-glucan concentrations used were 70.3 % and 80.3 %, respectively. These efficiency values are higher than those obtained when water was used for TPH removal but lower than those obtained when Tween-80 was used for TPH removal.

Marangoni flows triggered by cationic-anionic surfactant complexation.

HYPOTHESIS: The gradients in surfactant distribution at a fluid-fluid interface can induce fluid flow known as the Marangoni flow. Fluid interfaces found in biological and environmental systems are seldom clean, where mixtures of various surfactants are present. The presence of multi-component surfactant mixtures introduces the possibility of interactions among constituents, which may impact Marangoni flows and alter flow dynamics. EXPERIMENTS: We employed flow visualization, surface tension and reaction kinetic measurements, and numerical simulations to quantitatively investigate the Marangoni flows induced by the reacting surfactant mixtures. Different binary surfactant mixtures were utilized for comparative analysis. FINDINGS: The impact of surfactant interactions on Marangoni flows is confirmed through the observation of diverse complex flow patterns that result from the combination of oppositely charged surfactants in varying composition ratios and concentrations. Unique flow patterns originate from the composition-dependent interfacial phenomena upon mixing surfactants. Our findings provide vital insights that could be used to guide the development of effective oil remediation or the spreading of waterborne pathogens in contaminated regions.

Simulating asymmetric membranes using P21 periodic boundary conditions.

Molecular dynamics (MD) simulations of symmetric lipid bilayers are now well established, while those of asymmetric ones are considerably less developed. This disjunction arises in part because the surface tensions of leaflets in asymmetric bilayers can differ (unlike those of symmetric ones), and there is no simple way to determine them without assumptions. This chapter describes the use of P21 periodic boundary conditions (PBC), which allow lipids to switch leaflets, to generate asymmetric bilayers under the assumption of equal chemical potentials of lipids in opposing leaflets. A series of examples, ranging from bilayers with one lipid type to those with peptides and proteins, provides a guide for the use of P21 PBC. Critical properties of asymmetric membranes, such as spontaneous curvature, are highly sensitive to differences in the leaflet surface tensions (or differential stress), and equilibration with P21 PBC substantially reduces differential stress of asymmetric bilayers assembled with surface area-based methods. Limitations of the method are discussed. Technically, the nonstandard unit cell is difficult to parallelize and to incorporate restraints. Inherently, the assumption of equal chemical potentials, and therefore the method itself, is not applicable to all target systems. Despite these limitations, it is argued that P21 simulations should be considered when designing equilibration protocols for MD studies of most asymmetric membranes.

Role of Surface Tension on Heat Feedback and Power from Energetic Composites.

Heat feedback to the unburned reaction interface is an important controlling factor of the velocity of the reaction front and power delivery. In this paper, we investigate the effect of agglomerate surface tension and its relationship to surface residence time and heat feedback on the combustion characteristics by Si addition to an Al/KClO4 composite. Macroscopic imaging demonstrates a significant increase in burn rate with the addition of Si despite the fact that Si/KClO4 has a slightly lower energy density than Al/KClO4. Microscopic imaging coupled with three-color pyrometry reveals that molten liquid forms and evolves into spherical droplets on the burning surface, which are subsequently ejected from the surface. We find that the addition of Si results in a small increase in droplet size and a negligible impact on droplet temperature. However, the droplet formation rate on the surface is slower, leading to a significantly longer surface residence time. This leads to enhanced conductive heat feedback to the unburnt materials, thereby increasing the burn rate and energy release rate. We attribute the decreased droplet growth rate to the lowered surface tension of the liquid mixture with Si addition. This study highlights the crucial role of agglomerate physical property (e.g., surface tension) in influencing the combustion behavior of energetic composites.

Human Immunodeficiency Virus Type 1 Gag Polyprotein Modulates Membrane Physical Properties like a Surfactant: Potential Implications for Virus Assembly.

Human immunodeficiency virus (HIV) assembly at an infected cell's plasma membrane requires membrane deformation to organize the near-spherical shape of an immature virus. While the cellular expression of HIV Gag is sufficient to initiate budding of virus-like particles, how Gag generates membrane curvature is not fully understood. Using highly curved lipid nanotubes, we have investigated the physicochemical basis of the membrane activity of recombinant nonmyristoylated Gag-Δp6. Gag protein, upon adsorption onto the membrane, resulted in the shape changes of both charged and uncharged nanotubes. This shape change was more pronounced in the presence of charged lipids, especially phosphatidylinositol bisphosphate (PI(4,5)P2). We found that Gag modified the interfacial tension of phospholipid bilayer membranes, as judged by comparison with the effects of amphipathic peptides and nonionic detergent. Bioinformatic analysis demonstrated that a region of the capsid and SP1 domains junction of Gag is structurally similar to the amphipathic peptide magainin-1. This region accounts for integral changes in the physical properties of the membrane upon Gag adsorption, as we showed with the synthetic CA-SP1 junction peptide. Phenomenologically, membrane-adsorbed Gag could diminish the energetic cost of increasing the membrane area in a way similar to foam formation. We propose that Gag acts as a surface-active substance at the HIV budding site that softens the membrane at the place of Gag adsorption, lowering the energy for membrane bending. Finally, our experimental data and theoretical considerations give a lipid-centric view and common mechanism by which proteins could bend membranes, despite not having intrinsic curvature in their molecular surfaces or assemblies.

Dual function surfactants for pharmaceutical formulations: The case of surface active and antibacterial 1-tolyl alkyl biguanide derivatives.

One interesting field of research in the view of developing novel surfactants for pharmaceutical and cosmetic applications is the design of amphiphiles showing further bioactive properties in addition to those commonly displayed by surface-active compounds. We propose here the chemical synthesis, and characterization of 1-o-tolyl alkyl biguanide derivatives, having different lengths of the hydrocarbon chain (C3, C6, and C10), and showing surface active and antibacterial/disinfectant activities toward both Gram-positive and Gram-negative bacteria. Both surface active properties in terms of critical micelle concentration (CMC) and surface tension at CMC (γCMC), as well as the antimicrobial activity in terms of minimum inhibitory concentrations (MICs), were strongly dependent on the length of the hydrocarbon chain. Particularly, the C6 and C10 derivatives have a good ability to decrease surface tension (γCMC <40 mN/m) at low concentrations (CMC < 12 mM) and a satisfactory antibacterial effect (MIC values between 0.230 and 0.012 mM against S. aureus strains and between 0.910 and 0.190 against P.aeruginosa strains). Interestingly, these compounds showed a disinfectant activity at the tested concentrations that was comparable to that of the reference compound chlorhexidine digluconate. All these results support the possible use of these amphiphilic compounds as antibacterial agents and disinfectants in pharmaceutical or cosmetic formulations.

Ultra-high pressure treatment improve the content of characteristic aromatic components of melon juice from the view of physical changes.

Introduction: The effectiveness of ultra-high pressure (UHP) technology in retaining the flavor of fresh fruit and vegetable juices has been acknowledged in recent years. Along with previously hypothesized conclusions, the improvement in melon juice flavor may be linked to the reduction of its surface tension through UHP. Methods: In this paper, the particle size, free-water percentage, and related thermodynamic parameters of melon juice were evaluated in a physical point for a deeper insight. Results: The results showed that the UHP treatment of P2-2 (200 MPa for 20 min) raised the free water percentage by 7,000 times than the other treatments and both the melting enthalpy, binding constant and Gibbs free energy of P2-2 were minimized. This significantly increased the volatility of characteristic aromatic compounds in melon juice, resulting in a 1.2-5 times increase in the content of aromatic compounds in the gas phase of the P2-2 group compared to fresh melon juice.

Reconstructing the reflectivity of liquid surfaces from grazing incidence X-ray off-specular scattering data.

The capillary wave model of a liquid surface predicts both the X-ray specular reflection and the diffuse scattering around it. A quantitative method is presented to obtain the X-ray reflectivity (XRR) from a liquid surface through the diffuse scattering data around the specular reflection measured using a grazing incidence X-ray off-specular scattering (GIXOS) geometry at a fixed horizontal offset angle with respect to the plane of incidence. With this approach the entire Qz -dependent reflectivity profile can be obtained at a single, fixed incident angle. This permits a much faster acquisition of the profile than with conventional reflectometry, where the incident angle must be scanned point by point to obtain a Qz -dependent profile. The XRR derived from the GIXOS-measured diffuse scattering, referred to in this paper as pseudo-reflectivity, provides a larger Qz range compared with the reflectivity measured by conventional reflectometry. Transforming the GIXOS-measured diffuse scattering profile to pseudo-XRR opens up the GIXOS method to widely available specular XRR analysis software tools. Here the GIXOS-derived pseudo-XRR is compared with the XRR measured by specular reflectometry from two simple vapor-liquid interfaces at different surface tension, and from a hexadecyltri-methyl-ammonium bromide monolayer on a water surface. For the simple liquids, excellent agreement (beyond 11 orders of magnitude in signal) is found between the two methods, supporting the approach of using GIXOS-measured diffuse scattering to derive reflectivities. Pseudo-XRR obtained at different horizontal offset angles with respect to the plane of incidence yields indistinguishable results, and this supports the robustness of the GIXOS-XRR approach. The pseudo-XRR method can be extended to soft thin films on a liquid surface, and criteria are established for the applicability of the approach.

Evaluation of surface tensions and root-dentin surface contact angles of different endodontic irrigation solutions.

BACKGROUND: Surface tension and contact angle properties, which play a crucial role in determining the effectiveness of irrigation solutions in penetrating dentin surfaces and dentin tubules, are highly important for the development of new irrigation solutions and their preferences. The aim of the current study was to compare the surface tension and contact angle properties of different irrigation solutions used in endodontics, both on the dentin surface and within dentin tubules. METHODS: In this study, the contact angles and surface tensions of 5.25% sodium hypochlorite (NaOCl), 17% ethylenediaminetetraacetic acid (EDTA), 2% chlorhexidine (CHX), 5% boric acid (BA), 0.02% hypochlorous acid (HOCl), 0.2% chlorine dioxide (ClO2), Biopure MTAD, QMix solutions, and distilled water (control group) were measured. Measurements were conducted using a goniometer device (Attension Theta Lite Tensiometer, Biolin Scientific, USA), employing the sessile drop method for contact angle measurements on pre-prepared dentin surfaces, and the pendant drop method for surface tension. RESULTS: Contact angle measurements revealed no statistically significant differences between the contact angle values of MTAD, ClO2, and CHX or between NaOCl, QMix, BA, and HOCl (p > 0.05). However, EDTA exhibited a significantly greater contact angle than did MTAD, ClO2, CHX, NaOCl, QMix, BA, and HOCl (p < 0.05). Furthermore, the contact angle of dentin with distilled water was greater than that with all other solutions tested (p < 0.05). Surface tension measurements revealed that the surface tension values of QMix and MTAD were statistically similar (p > 0.05). CHX exhibited lower surface tension than distilled water and HOCl (p < 0.05), and it also had lower surface tension than ClO2, NaOCl, and BA (p < 0.05). Additionally, the surface tension of the samples treated with EDTA was greater than that of all other solutions tested (p < 0.05). CONCLUSION: The direct linear relationship between the surface tension of liquids and contact angles on different surfaces may not always hold true, and these values should be considered independently for each solution on various surfaces. Considering the contact angles and surface tension properties of irrigation solutions with root canal dentin, it can be suggested for clinical use that ClO2 could be recommended over NaOCl, and similarly, BA could be recommended over EDTA.

Measuring the Shape, Stiffness, and Interface Tension of Droplets with the Scanning Ion Conductance Microscope.

Imaging and probing liquid-liquid interfaces at the micro- and nanoscale are of high relevance, for example, in materials science, surface chemistry, and microfluidics. However, existing imaging techniques are limited in resolution, average over large sample areas, or interact with the sample. Here, we present a method to quantify the shape, stiffness, and interface tension of liquid droplets with the scanning ion conductance microscope (SICM), providing submicrometer resolution and the ability to perform noncontact mechanical measurements. We show that we can accurately image the three-dimensional shape of micrometer-sized liquid droplets made of, for example, decane, hexane, or different oils. We then introduce numerical models to quantitatively obtain their stiffness and interface tension from SICM data. We verified our method by measuring the interface tension of decane droplets changing under the influence of surfactants at different concentrations. Finally, we use SICM to resolve the dissolution dynamics of decane droplets, showing that droplet shape exhibits different dissolution modes and stiffness continuously increases while the interface tension remains constant. We thereby demonstrate that SICM is a useful method to investigate liquid-liquid interfaces on the microscale with applications in materials or life sciences.

An Insightful Overview of Microbial Biosurfactant: A Promising Next-Generation Biomolecule for Sustainable Future.

Microbial biosurfactant is an emerging vital biomolecule of the 21st century. They are amphiphilic compounds produced by microorganisms and possess unique properties to reduce surface tension activity. The use of microbial surfactants spans most of the industrial fields due to their biodegradability, less toxicity, being environmentally safe, and being synthesized from renewable sources. These would be highly efficient eco-friendly alternatives to petroleum-derived surfactants that would open up new approaches to research on the production of biosurfactants. In the upcoming era, biobased surfactants will become a dominating multifunctional compound in the world market. Research on biosurfactants ranges from the search for novel microorganisms that can produce new molecules, structural and physiochemical characterization of biosurfactants, and fermentation process for enhanced large-scale productivity and green applications. The main goal of this review is to provide an overview of the recent state of knowledge and trends about microbially derived surfactants, various aspects of biosurfactant production, definition, properties, characteristics, diverse advances, and applications. This would lead a long way in the production of biosurfactants as globally successful biomolecules of the current century.

Preliminary analysis: Effect of a rotary generator of hydrodynamic cavitation on rheology and methane yield of wastewater sludge.

Slightly acidic (pH 5.1) waste sludge with 4.7 % Total Solids (TS) was treated on a laboratory scale pined disc rotary generator of hydrodynamic cavitation (PD RGHC). Influence of four rotor discs with different number of cavitation generation units (CGUs) was investigated: 8-pins, 12-pins, 16-pins and 8-prism elements. The effect of hydrodynamic cavitation (HC) was investigated by analyzing rheological properties, surface tension, dewaterability, and particle size distribution. After subjecting the sludge to 30 cavitation passes, the dewatering ability of the sludge significantly decreased, resulting in a more than two-fold increase in Capillary Suction Time (CST). All regimes were successful in disintegrating particles to smaller sizes. A slight increase of sludge surface tension was measured post cavitation. Cavitated samples displayed a zero-shear viscosity, in contrast to the untreated sample, where viscosity noticeably increased as shear stress decreased. HC did not improve methane yield. Statistically significant correlations between physio-chemical properties and apparent viscosity at low shear stress were identified. Although there were no discernible statistical differences in sludge characteristics, some trends are visible among investigated CGU designs and warrant further research.

Evidence of Surface-Tension Lowering of Atmospheric Aerosols by Organics from Field Observations in an Urban Atmosphere: Relation to Particle Size and Chemical Composition.

Surface-active organics lower the aerosol surface tension (σs/a), leading to enhanced cloud condensation nuclei (CCN) activity and potentially exerting impacts on the climate. Quantification of σs/a is mainly limited to laboratory or modeling work for particles with selected sizes and known chemical compositions. Inferred values from ambient aerosol populations are deficient. In this study, we propose a new method to derive σs/a by combining field measurements made at an urban site in northern China with the κ-Köhler theory. The results present new evidence that organics remarkably lower the surface tension of aerosols in a polluted atmosphere. Particles sized around 40 nm have an averaged σs/a of 53.8 mN m-1, while particles sized up to 100 nm show σs/a values approaching that of pure water. The dependence curve of σs/a with the organic mass resembles the behavior of dicarboxylic acids, suggesting their critical role in reducing the surface tension. The study further reveals that neglecting the σs/a lowering effect would result in lowered ultrafine CCN (diameter <100 nm) concentrations by 6.8-42.1% at a typical range of supersaturations in clouds, demonstrating the significant impact of surface tension on the CCN concentrations of urban aerosols.