Ceramic primer heat-treatment effect on resin cement/Y-TZP bond strength.

The purpose of this study was to evaluate the effect of different heat-treatment strategies for a ceramic primer on the shear bond strength of a 10-methacryloyloxydecyl-dihydrogen-phosphate (MDP)-based resin cement to a yttrium-stabilized tetragonal zirconia polycrystal (Y-TZP) ceramic. Specimens measuring 4.5 × 3.5 × 4.5 mm(3) were produced from Y-TZP presintered cubes and embedded in polymethyl methacrylate (PMMA). Following finishing, the specimens were cleaned using an ultrasound device and distilled water and randomly divided into 10 experimental groups (n=14) according to the heat treatment of the ceramic primer and aging condition. The strategies used for the experimental groups were: GC (control), without primer; G20, primer application at ambient temperature (20°C); G45, primer application + heat treatment at 45°C; G79, primer application + heat treatment at 79°C; and G100, primer application + heat treatment at 100°C. The specimens from the aging groups were submitted to thermal cycling (6000 cycles, 5°C/55°C, 30 seconds per bath) after 24 hours. A cylinder of MDP-based resin cement (2.4 mm in diameter) was constructed on the ceramic surface of the specimens of each experimental group and stored for 24 hours at 37°C. The specimens were submitted to a shear bond strength test (n=14). Thermal gravimetric analysis was performed on the ceramic primer. The data obtained were statistically analyzed by two-way analysis of variance and the Tukey test (α=0.05). The experimental group G79 without aging (7.23 ± 2.87 MPa) presented a significantly higher mean than the other experimental groups without aging (GC: 2.81 ± 1.5 MPa; G20: 3.38 ± 2.21 MPa; G100: 3.96 ± 1.57 MPa), showing no difference from G45 only (G45: 6 ± 3.63 MPa). All specimens of the aging groups debonded during thermocycling and were considered to present zero bond strength for the statistical analyses. In conclusion, heat treatment of the metal/zirconia primer improved bond strength under the initial condition but did not promote stable bonding under the aging condition.

Enzymatic production of biodiesel from cotton seed oil using t-butanol as a solvent.

The enzymatic production of biodiesel by methanolysis of cottonseed oil was studied using immobilized Candida antarctica lipase as catalyst in t-butanol solvent. Methyl ester production and triacylglycerol disappearance were followed by HPLC chromatography. It was found, using a batch system, that enzyme inhibition caused by undissolved methanol was eliminated by adding t-butanol to the reaction medium, which also gave a noticeable increase of reaction rate and ester yield. The effect of t-butanol, methanol concentration and temperature on this system was determined. A methanolysis yield of 97% was observed after 24h at 50 degrees C with a reaction mixture containing 32.5% t-butanol, 13.5% methanol, 54% oil and 0.017 g enzyme (g oil)(-1). With the same mixture, a 95% ester yield was obtained using a one step fixed bed continuous reactor with a flow rate of 9.6 mlh(-1) (g enzyme)(-1). Experiments with the continuous reactor over 500 h did not show any appreciable decrease in ester yields.

Crosslinked penicillin acylase aggregates for synthesis of beta-lactam antibiotics in organic medium.

Crosslinked enzyme aggregates (CLEAs) of a partially purified penicillin acylase from a recombinant Escherichia coli strain have been produced as a novel type of biocatalysts well endowed to perform in organic media. Different protein precipitants were studied and glutaraldehyde was used as the crosslinking agent. Precipitation curves were obtained for all precipitants to determine the concentrations at which all the protein precipitated out of the solution. The effect of the glutaraldehyde-to-protein ratio was studied with respect to process recovery and the specific activity and stability of the biocatalyst. Recovery of penicillin acylase activity was moderately high, about 50%; major losses of enzyme activity were produced at the precipitation step. Specific activities of all CLEAs were very high, which is one of the advantages of using nonsupported biocatalysts. Ammonium sulfate and tert-butyl alcohol were the best precipitants at a glutaraldehyde-protein mass ratio of 2 and were selected to perform the kinetically controlled synthesis of ampicillin in 60% (v/v) ethylene glycol medium. At comparable conversion yields, volumetric and specific antibiotic productivity were much higher for CLEAs than for carrier-bound penicillin acylases.