Marginal adaptation and fracture resistance of feldspathic and polymer-infiltrated ceramic network CAD/CAM endocrowns for maxillary premolars.

OBJECTIVE: The aim of this study was to evaluate the marginal adaptation and fracture resistance of feldspathic and Polymer-Infiltrated Ceramic Network (PICN) CAD/CAM endocrowns for maxillary premolars. MATERIALS AND METHODS: Twenty extracted human permanent maxillary premolars were randomly divided into two groups (n = 10); Group CEREC (GC), which was produced by feldspathic ceramic and the Group Enamic (GE), which was produced by PICN. All teeth were endodontically treated and decoronated horizontally at 2 mm above the cemento-enamel junction. Endocrown preparations were done with 4 mm depth into the pulp chamber. Endocrowns were manufactured using CAD/CAM from ceramic blocks. Following adhesive cementation, all specimens were subjected to thermocycling. Marginal adaptation evaluated under SEM at 200 × magnification. Each specimen was fixed in a universal testing machine and a compressive load was applied at 45° to long axis of the teeth until failure. Failure load was recorded and failure modes were evaluated. Statistical analyses were performed with SPSS 19.0 software and data were compared using Mann-Whitney U test. RESULTS: There were no significant differences in the marginal adaptation between two groups (P > 0.05). GE presented significantly higher fracture resistance when compared to GC (P < 0.05). Failure pattern was similar and characterized by the tooth-ceramic fracture on the force-applied side. CONCLUSIONS: CAD/CAM fabricated feldspathic ceramic and PICN endocrowns provide sufficient marginal adaptation, but the PICN endocrowns shows higher fracture resistance than the feldspathic ceramic endocrowns.

Polyamines and microbiota in bicuspid and tricuspid aortic valve aortopathy.

Polyamines are small aliphatic cationic molecules synthesized via a highly regulated pathway and involved in general molecular and cellular phenomena. Both mammalian cells and microorganisms synthesize polyamines, and both sources may contribute to the presence of polyamines in the circulation. The dominant location for microorganisms within the body is the gut. Accordingly, the gut microbiota probably synthesizes most of the polyamines in the circulation in addition to those produced by the mammalian host cells. Polyamines are mandatory for cellular growth and proliferation. Established evidence suggests that the polyamine spermidine prolongs lifespan and improves cardiovascular health in animal models and humans through both local mechanisms, involving improved cardiomyocyte function, and systemic mechanisms, including increased NO bioavailability and reduced systemic inflammation. Higher levels of polyamines have been detected in non-dilated aorta of patients affected by bicuspid aortic valve congenital malformation, an aortopathy associated with an increased risk for thoracic ascending aorta aneurysm. In this review, we discuss metabolism of polyamines and their potential effects on vascular smooth muscle and endothelial cell function in vascular pathology of the thoracic ascending aorta associated with bicuspid or tricuspid aortic valve.

Fracture Strength and Stress Distribution in Premolars Restored with Cast Post-and-Cores or Glass-Fiber Posts Considering the Influence of Ferule.

OBJECTIVES: The aim of this study was to evaluate the influence of ferule and the post type on the fracture strength and stress distribution in premolars. MATERIALS AND METHODS: Forty human mandibular premolars were decoronated, allocated in four groups, and restored as follows: CPC-NF: cast post-and-core and absence of ferule; CPC-F: cast post-and-core and presence of ferule; FPC-NF: glass-fiber posts and absence of ferule; FPC-F: glass-fiber posts and presence of ferule. The fracture strength (FS) and failure patterns were evaluated. Finite element analysis (FEA) evaluated the stress distribution. RESULTS: FS did not differ between CPCs and FPC either in presence or in absence of ferule. The presence of ferule increased FS with both post types. Mean values of FS for ferule groups were higher than functional or parafunctional loads reported in literature, which was not the case for FPC-NF when compared to parafunctional loads. FEA with a functional load showed slightly higher compressive stresses in dentin in the group CPC-NF, which was much lower than the compressive strength of dentin. Lower percentage of catastrophic failures was observed in nonferule groups irrespective of post type, which was explained by the stress concentration in the cervical root region when FEA with the FS load was simulated. CONCLUSION: Ferule effect was shown to be more important than post type in the analysis. Both posts showed potential to withstand functional loads irrespective of presence of ferule. However, the mean FS was lower than parafunctional loads for FPC in the absence of ferule.

Can interfaces at bracket-wire and between teeth in multi-teeth finite element model be simplified?

OBJECTIVE: Finite element (FE) method's correctness depends heavily on modeling method. This study aimed at determining whether the interfaces at bracket-wire and between teeth can be simplified for multi-teeth FE analysis. METHOD: A three-dimensional FE model of a mandible was created from cone-beam computed tomography scan. Due to symmetry, only a half of the mandible was modeled, which consisted of five teeth (first premolar extraction and only first molar), brackets and archwire, periodontal ligament (PDL), cortical bone, and cancellous bone. All the bone, teeth, and PDL were considered to be isotropic and linear. The En-masse retraction case was simulated. A detailed model, which has contact elements between the bracket and archwire and between teeth, was developed to allow relative motion at the interfaces. A model with simplified interfacial conditions, which does not allow the relative motion, was also created. The stresses and displacements as results of the treatment on these two models were calculated and compared. RESULTS: The stress and displacement distributions from the detailed model were more close to reality based on the expected displacement pattern of the clinical case than from the simplified model. The maximum stresses from the two methods were also different. The highest stress from the detailed model is twice as high as from the simplified model. CONCLUSIONS: The detailed model provides much more reasonable results than the simplified model. Thus, the simplified model should not be used to replace the detailed model if the stress magnitude and highest stress location are the expected outcomes.

Evaluation of fracture resistance in root canal-treated teeth restored using different techniques.

OBJECTIVE: This study aimed to evaluate the effects of different coronal restoration techniques on fracture resistance of root canal-treated mandibular premolars with mesio-occluso-distal (MOD) cavities. MATERIALS AND METHODS: A total of 105 mandibular premolars were selected and randomly distributed into seven groups (n = 15). MOD cavities were prepared except the control group. Root canal treatments were performed. Each tooth was embedded in acrylic resin. Groups were classified as follows; G1: intact teeth (control), G2: unfilled MOD cavity, G3: MOD + composite resin, G4: 10-mm-long fiber post + composite resin, G5: 5-mm-long fiber post + composite resin, G6: Ribbond in the occlusal surface + composite resin, and G7: horizontal fiber post + composite resin. Specimens were loaded using a universal testing machine until fracture occurs. Fracture loads were recorded and statistical interpretations were made (α = 0.05). RESULTS: In Groups 1, 6, and 7, the greatest fracture resistance was shown and there were no significant differences among these groups (P > 0.05). No significant differences were detected among the Groups 3, 4, and 5 (P > 0.05), whereas the fracture resistances of Groups 1, 6, and 7 were significantly greater than these three groups (P < 0.05). Group 2 had the lowest fracture resistance of all groups (P < 0.05). CONCLUSION: Usage of horizontal post or occlusal Ribbond usage increased the fracture resistance of root canal-treated premolars with MOD cavities.

In vitro fracture strength and patterns in root-filled teeth restored with different base materials.

BACKGROUND: There is little research on the effects of an intermediate base on the fracture strength of root-filled teeth. This study compared the fracture strengths and patterns of root-filled teeth restored with intermediate bases of glass-ionomer cement (GIC), zinc polycarboxylate cement (ZPC), dual-cured resin composite (DCRC) and Biodentine® under resin composite. METHODS: Standardized cavities were prepared in 100 extracted human maxillary and mandibular premolars, and root canal treatment was performed. The teeth were stratified and randomly allocated to five groups (n = 20): (i) GIC; (ii) ZPC; (iii) DCRC; (iv) Biodentine; and (v) prepared but unrestored (control). The teeth were subjected to an oblique, ramped load until fracture. The fracture loads, level, mode and location were recorded. RESULTS: Mean fracture strengths of all restored groups were not significantly different amongst the groups. There were significant overall effects on mean fracture strength for tooth type (P = 0.002) and buccolingual width of the crown (P = 0.001). CONCLUSIONS: The four materials were appropriate intermediate bases. The laminate restorative technique promoted fracture strengths that are likely to withstand normal and maximum masticatory function. The base material can influence failure mode, which may have implications for the clinical presentation of fractures of root-filled teeth.

Ankylosis of Permanent First Molar: Diagnosis by Cone Beam Computed Tomography / Anquilosis del Primer Molar Permanente: Diagnóstico por Tomografía Computarizada con Haz Cónico

ABSTRACT: Ankylosis is an anomaly of tooth eruption characterized by the fusion of cementum and alveolar bone, and may affect from small regions to the entire root surface. Clinical assessment combined with imaging exams can aid diagnosis. Radiographic testing enables assessing only proximal regions of possibly affected roots. Whereas cone beam computed tomography (CBCT) allows a three-dimensional assessment of axial, coronal, and sagittal planes of all dental extension, eliminating thus overlapping images and helping to confirm the correct diagnosis. The present study contains a case report of a male patient with ankylosis in tooth 16 diagnosed by CBCT, aiming at providing information for dentists about this anomaly, its characteristics and situations in which CBCT should be indicated.

RESUMEN: La anquilosis es una anomalía de la erupción del diente caracterizada por la fusión de cemento y hueso alveolar, y puede afectar desde pequeñas regiones hasta toda la superficie de la raíz. La evaluación clínica combinada con los exámenes de imagen puede ayudar a diagnosticar esta anomalía. Las pruebas radiográficas permiten evaluar sólo las regiones proximales de las raíces posiblemente afectadas. La tomografía computarizada de haz de cono (CBCT) permite una evaluación tridimensional de los planos axial, coronal y sagital de toda la extensión dental, eliminando así las imágenes superpuestas y ayudando a confirmar el diagnóstico correcto. En el presente estudio se presenta un reporte de caso de un paciente con anquilosis en el diente 16 diagnosticado por CBCT, con el objetivo de proporcionar información para los dentistas sobre esta anomalía, sus características y situaciones en las que debe indicarse la CBCT.

Pendulum and modified pendulum appliances for maxillary molar distalization in Class II malocclusion - a systematic review.

OBJECTIVE: The main purpose of the present systematic review was to evaluate the quantitative effects of the pendulum appliance and modified pendulum appliances for maxillary molar distalization in Class II malocclusion. MATERIALS AND METHODS: Our systematic search included MEDLINE, EMBASE, CINAHL, PsychINFO, Scopus and key journals and review articles; the date of the last search was 30 January 2017. We graded the methodological quality of the studies by means of the Quality Assessment Tool for Quantitative Studies, developed for the Effective Public Health Practice Project (EPHPP). RESULTS: In total, 203 studies were identified for screening, and 25 studies were eligible. The quality assessment rated four (16%) of the study as being of strong quality and 21 (84%) of these studies as being of moderate quality. The pendulum appliances showed mean molar distalization of 2-6.4 mm, distal tipping of molars from 6.67° to 14.50° and anchorage loss with mean premolar and incisor mesial movement of 1.63-3.6 mm and 0.9-6.5 mm, respectively. The bone anchored pendulum appliances (BAPAs) showed mean molar distalization of 4.8-6.4 mm, distal tipping of molars from 9° to 11.3° and mean premolar distalization of 2.7-5.4 mm. CONCLUSIONS: Pendulum and modified pendulum appliances are effective in molar distalization. Pendulum appliance with K-loop modification, implant supported pendulum appliance and BAPA significantly reduced anchorage loss of the anterior teeth and distal tipping of the molar teeth.

Orthodontically induced cervical root resorption in humans is associated with the amount of tooth movement.

INTRODUCTION: The aim of this study was to investigate the variation in the amount of the orthodontically induced cervical root resorption and the association with several factors, such as the amount of tooth displacement, location of tooth in the maxilla or mandible, and presence of an interference that may influence the amount of root resorption. SUBJECTS AND METHODS: This study included 30 subjects (20 females, 10 males) with an age range of 11.3 to 43.0 years. Using a standardized experimental orthodontic tooth movement, 59 premolars were moved buccaly during 8 weeks with application of 1 N force. Fifty-eight contralateral premolars not subjected to orthodontic tooth movement served as controls. At the end of the experimental period the teeth were carefully extracted, scanned in a micro-computed tomography scanner with a resolution of 9 µm, and the reconstructed images were processed for volumetric evaluation of resorption craters at the cervical part of the root surface. Data were analyzed using unpaired t-test and the Pearson's correlation. RESULTS: Higher amount of cervical root resorption was detected in the orthodontically moved teeth (0.00055 mm3) compared to controls (0.00003 mm3; P < 0.001). Moderate correlation was found between root resorption in the two experimental teeth within the same individual (R = 0.421, P = 0.023). Teeth located in the mandible presented more resorption than those in the maxilla (P = 0.046). The amount of root resorption was correlated to the amount of tooth movement (R = 0.318, P = 0.016). CONCLUSION: Application of a 1 N force over a 2-month period provokes severe root resorption at the compression cervical sites. Resorption is correlated with the amount of tooth movement and the location of the teeth.

The extent of root resorption and tooth movement following the application of ascending and descending magnetic forces: a prospective split mouth, microcomputed-tomography study.

OBJECTIVE: Various factors have been examined in the literature in an attempt to reduce the incidence and severity of root resorption. The purpose of the present investigation is to test the null hypothesis that there is no difference in relation to force level using gradually increasing (ascending) and decreasing (descending) orthodontic force generated by magnets on the severity of Orthodontically Induced Inflammatory Iatrogenic Root Resorption (OIIRR) and amount of tooth movement. METHODS: Twenty maxillary first premolars from 10 patients were subjected to ascending (25-225 g, magnets in attraction) and descending (225 to 25 g, magnets in repulsion) buccal forces using a split mouth design over an 8-week period. Polyvinyl siloxane impressions were taken at week 0, 4, and 8 to record the tooth movement. After 8 weeks, the teeth were extracted, scanned, with micro-CT in 16.9 µm resolution, and the root resorption craters were localized circumferentially and quantified at each level of the root. RESULTS: The total volume of OIIRR with ascending force was 1.20 mm3, and with descending force was 1.25 mm3, and there was no statistically significant difference between them. OIIRR on the palatal surface (0.012 mm3) was significantly less than on the buccal surface (0.057 mm3) and than on the mesial surface (0.035 mm3). There is no statistically significant difference in the degree of OIIRR between different level of the root (cervical, middle, and apical) at different surfaces. Moreover, the amount of tooth movement, at 0-, 4-, and 8-week interval, secondary to an ascending and descending force application was not statistically significant. CONCLUSIONS: There is no short-term (8 weeks) statistically significant difference between orthodontic ascending and descending forces, from 25 to 225 g and from 225 to 25 g, respectively, in term of severity and location of OIIRR as well as the amount of tooth movement. The buccal surface of the root showed highest degree of OIIRR compared to other root's surfaces.

[Impact of different degree pulpitis on cell proliferation and osteoblastic differentiation of dental pulp stem cell in Beagle immature premolars].

OBJECTIVE: To compare the proliferation and osteoblastic differentiation of dental pulp stem cell (DPSC) isolated from normal and inflamed pulps of different degrees in Beagle immature premolars, and provide evidence for the use of inflammatory DPSC (IDPSC). METHODS: This study evaluated 14 Beagle's young premolars (21 roots). In the experiment group, irreversible pulpitis was induced by pulp exposure and the inflamed pulps were extracted 2 weeks and 6 weeks after the pulp chamber opening.For the control group, normal pulps were extracted immediately after the exposure. HE staining and real-time PCR were performed to confirm the inflammation. The cells were isolated from the inflamed and normal pulps (IDPSC and DPSC). Cell proliferation and osteoblastic differentiation potentials of the two cells were compared. RESULTS: Inflammation cells infiltration was observed in the inflamed pulps by HE staining. The expression of inflammatory factor was much higher in the 6 week inflamed pulp. IDPSC had higher potential of cell proliferation and osteoblastic differentiation potentials. Furthermore, the osteoblastic differentiation potentials of IDPSC from 2 week inflamed pulp were higher than those from 6 week inflamed pulp. CONCLUSION: The potential of cell proliferation and osteoblastic differentiation of DPSC was enhanced at early stage of irreversible pulpitis, and reduced at late stage in Beagle immature premolars.

Root Fracture of Abutment Teeth for Partial Removable Dental Prostheses.

PURPOSE: Root fracture is a common and serious cause of abutment tooth loss. No studies to date have comprehensively assessed the individual contributions of the factors that increase stress on abutment teeth. The purpose of this study was to analyze the stress distribution in abutment teeth based on a three-dimensional finite element model and to analyze the factors that affect stress distribution. MATERIALS AND METHODS: Models were generated from the computed tomography data of a single patient, consisting of a mandibular second premolar abutment tooth, bone, residual mucous membrane, and a partial removable dental prosthesis (PRDP). Four models were prepared using different types of endodontic posts and cores. Akers clasps were used for the simulated PRDPs, and a vertical load was applied to the occlusal surface of the PRDPs. Debonding between the post and root was simulated. The Young modulus of the residual ridge was reduced to simulate a poor fit between the denture base and the residual ridge. Stress distribution in the abutment tooth root was observed, and the maximum principal stress was evaluated. RESULTS: The nonmetal post model and the mesial rest model reduced stress concentration in the root. The stress increased in models simulating debonding and poor fit. The results of the multiple linear regression analysis confirmed that debonding and poor fit were significantly associated with root stress. CONCLUSION: Within the limitations of this study, it is suggested that the bonding integrity of posts and adequate fit of the denture base are important factors affecting the longevity of abutment teeth for PRDPs.

Restorative material and loading type influence on the biomechanical behavior of wedge shaped cervical lesions.

OBJECTIVES: To evaluate the influence of restorative materials used on the rehabilitation of MOD cavities and loading type, on biomechanical behavior of wedge-shaped (WS) lesions in endodontically treated maxillary premolars. The investigation was conducted by 3D finite element analysis (FEA) and strain gauge test. MATERIALS AND METHODS: Six models were generated, with MOD cavities and endodontic treatment: A (MOD amalgam restoration), R (MOD composite restoration), AL (A + cervical lesion (L)), RL, ALR (A + cervical lesion restored with composite (LR)), and RLR. Each model underwent two compressive loading (100N): axial and oblique-45° angle to the long axis on the buccal cusp. The models were analyzed by von Mises criteria. For strain gauge test, 14 standardized maxillary premolars were treated according to the groups described for FEA. Two strain gauges were bonded on each sample submitted to compressive loading in a mechanical testing machine. RESULTS: A presented higher stress concentration and strain values than R. Oblique loading promoted highest stress concentration and strain rates for all groups. ALR and RLR presented similar stress-strain distribution pattern when compared to A and R. CONCLUSION: The interaction between MOD cavity restored with amalgam and oblique loading propitiated the highest stress concentration and strain values on cervical region and WS lesion. CLINICAL RELEVANCE: The MOD cavity restored with composite resin is a better option than amalgam to improve the biomechanical behavior of wedge-shaped lesion, avoiding dental failure. In addition, the occlusal interferences must be removed, allowing homogeneous contact distribution and preventing WS lesion progression.

Effect of Root Filling on Stress Distribution in Premolars with Endodontic-Periodontal Lesion: A Finite Elemental Analysis Study.

INTRODUCTION: Endodontic-periodontal (EP) lesions require both endodontic and periodontal therapies. Impermeable sealing of the root canal system after cleaning and shaping is essential for a successful endodontic treatment. However, complete healing of the hard and soft tissue lesions takes time, and diseased bone, periodontal ligament, and tooth fibrous joints are reported to have an increased failure risk for a given load. Considering that EP lesions may affect the biomechanics of teeth, this finite elemental analysis study aimed to test the effect of root fillings on stress distribution in premolars with EP lesions. METHODS: Three finite elemental analysis models representing 3 different types of EP lesions (primary endodontic disease [PED], PED with secondary periodontic involvement, and true combined) were created. The root canals were assumed as nonfilled or filled with gutta-percha, gutta-percha/apical mineral trioxide aggregate (MTA) plug, and MTA-based sealer. Materials used were assumed to be homogenous and isotropic. A 300-N load was applied from the buccal cusp of the crown with a 135° angle. The Cosmoworks structural-analysis program (SolidWorks Corp, Waltham, MA) was used for analysis. Results were presented considering von Mises criteria. RESULTS: Stresses at the root apex increased with an increase in lesion dimensions. Root filling did not affect stress distribution in the PED model. An MTA plug or MTA-based sealer created more stress areas within the root compared with the others in the models representing PED with periodontic involvement and true combined lesions. CONCLUSIONS: Stresses at the apical end of the root increase with increases in lesion dimensions. MTA-based sealers or an MTA plug creates more stresses when there is periodontic involvement or a true combined lesion.

Slow and fast orthodontic tooth movement: an experimental study on humans.

INTRODUCTION: The aim of this study was to investigate the variation in the amount of the orthodontically induced tooth movement in humans and potential associations between the amount of tooth movement with age and location in the mandible or maxilla. SUBJECTS AND METHODS: This study included 11 participants (7 females, 4 males) with an age range of 11.3-28.6 years. In a standardized experimental orthodontic tooth movement protocol, two premolars of each participant were moved buccally during 8 weeks with the use of 1 N force. No functional or localized obstacles were affecting the displacement. Plaster models before and after the experimental tooth movement were constructed, digitized, and superimposed, to evaluate the amount of tooth movement of each tooth. Random effects linear regression analysis was performed to examine associations between tooth displacement, age, and tooth location. RESULTS: The mean displacement of the teeth was 2.7±1.4mm. The range of tooth movement varied substantially between individuals (0.6-5.8mm). The displacement of the teeth within the same individual was highly correlated (R (2) = 0.78, P < 0.001). The tooth displacement decreased with age; however, this finding did not reach statistical significance (ß = -0.11, 95% CI: -0.28, 0.05, P = 0.172). The tooth movement was higher in the maxilla than in the mandible (ß = 0.47, 95% CI: 0.81, 0.86, P = 0.018). CONCLUSION: Wide range of tooth displacement revealed slow and fast movers in this sample. Larger displacements were recorded in the maxilla compared to the mandible and in younger individuals.

Biomechanical Behavior of Extensively Restored Premolars: Cusp Deformation, Marginal Integrity, and Fracture Resistance.

PURPOSE: To study the biomechanical behavior of extensively restored premolars by determining the effect of the composite type, presence of cusp weakening, and compressive loading on the cusp deformation (CD), marginal integrity (MI), and fracture resistance (FR) of directly restored premolars. MATERIALS AND METHODS: Forty premolars received Class II mesio-occlusal-distal (MOD) cavities and were divided into 4 groups (n = 10) in accordance with the two study variables: composite type (conventional: Filtek Z250 XT [Z250], 3M ESPE; low shrinkage: Venus Diamond [VD], Heraeus-Kulzer) and the presence of cusp weakening (with/without). Cusp deformation upon restoration was assessed using strain gauges during the restorative procedure and thereafter when the restorations were subjected to an occlusal load of 100 N. The samples were subjected to thermal and mechanical cycling. Epoxy resin replicas of the proximal tooth/restoration interfaces were made to analyze the marginal integrity (MI) using scanning electron microscopy. To determine the fracture resistance (FR), the teeth were loaded at a crosshead speed of 0.5 mm/min until fracture. RESULTS: The conventional composite Z250 had higher CD, lower MI, and lower FR than the low-shrinkage composite VD. Cusp weakening had no influence on CD, but MI and FR decreased. CONCLUSION: The low-shrinkage composite VD performed better in restoring extensively destroyed premolars than did Z250.

Agenesis of second premolars and delayed dental maturation.

AIM: The purpose of this work was to examine the relationship between second-premolar agenesis and how rapidly permanent dentition develops. METHODS: Panoramic radiographs of 678 girls and boys aged 6-14 years were evaluated. Subjects with syndromes or history of tooth extraction were excluded. The permanent dentition's stages of mineralization (scale 1-10) and eruption (1-7), and the resorption (1-5) of deciduous teeth were assessed. RESULTS: Adjusted for age and sex, subjects with one or more missing second premolars revealed earlier developmental stages (mineralization: average -0.37 stages per tooth, 95% CI -0.23 to -0.50; eruption: -0.42, 95% CI -0.60 to -0.24; resorption: -0.36, 95% CI -0.49 to -0.24; all p < 0. 001). Canines, premolars, and second molars were particularly affected, regardless of their location in the same or opposing jaw, and independent of the number of missing teeth. Overall dental development was delayed by 8.6 months (95% CI 5.4-11.8) in subjects with missing second premolars. CONCLUSION: These results have implications for several areas of medicine. Joint biological etiology for the agenesis and late maturation of permanent teeth should be considered in developmental research. Orthodontists should be aware of the delay associated with missing second premolars when timing interventions. Forensic age assessment based on tooth development should adjust for missing teeth to avoid underestimating the subject's age.

Maturogenesis of an Early Erupted Immature Permanent Tooth: A Case Report With 7-Year Follow-Up.

The main objective of treatment of an undeveloped tooth (immature) is to provide vital pulp therapy to allow continued development of root dentin. A case report is presented that demonstrates the use of calcium hydroxide (CaOH2) as an indirect pulp-copping material for the purpose of continued maturogenesis of an early-erupted permanent tooth with severe mobility and almost-begun root formation. Seven-year radiographic and clinical follow-up demonstrated a vital pulp and physiologic root development without any endodontic failure clinically or radiographicaly.

Microscopic morphological changes of the tooth surface in relation to fixed orthodontic treatment.

Orthodontic treatment has, as any other medical intervention, in addition to its benefits, side effects, some of them being perceived as unavoidable. The aim of this case series was to microscopically evaluate the changes of the tooth surface in relation to fixed orthodontic treatment. A case series study was implemented by the usage of four extracted first maxillary premolars, from patients with previous orthodontic treatment, of 12 and 23 months. Analysis was performed using the high precision stereomicroscope (Axiovert, Carl Zeiss, Germany), at magnifications from 10× to 50×. The tooth surface corresponding to the bracket bonding area registered numerous disorderly grooves and cracks, with various directions and depths, and was flattened, having lower convexity compared to teeth surfaces where brackets were not bonded. Root resorption lacunae were more frequently observed in teeth under orthodontic treatment, these having various depths, and sizes considerably larger than those observed in teeth without orthodontic treatment. Following orthodontic treatment, teeth exhibit changes that can be perceived as being directly linked to this medical intervention. These teeth changes usually have low or moderate severity, which can be influenced at some degree by the clinical conduct of the orthodontic treatment. The stereomicroscope proved to be a high sensitivity tool for the analysis of morphological changes of teeth in relation to the fixed orthodontic treatment.

Effect of ferrule location on the fracture resistance of crowned mandibular premolars: An in vitro study.

STATEMENT OF PROBLEM: How the location of a ferrule affects the fracture resistance of endodontically treated mandibular premolars is unclear. PURPOSE: The purpose of this in vitro study was to compare the effect of ferrule location on the fracture resistance of endodontically treated mandibular premolars. MATERIAL AND METHODS: Seventy-two extracted human mandibular premolars were selected and divided into 6 test groups (n = 12) according to ferrule location: control group, GHT; endodontically treated teeth without endodontic posts and crowns, GCF; teeth with a 2 mm circumferential ferrule, GBF; teeth with a 2 mm buccal ferrule; GLF, teeth with a 2 mm lingual ferrule; GBLF, teeth with a 2 mm buccal and lingual ferrule; and teeth without ferrule, GWF. After glass fiber posts were cemented with a self-adhesive resin cement and foundation restorations were placed, NiCr crowns were luted to each prepared tooth. All specimens were quasistatically loaded at 30 degrees in a universal testing machine until fractured. Data were then analyzed with 1-way ANOVA, followed by multiple comparisons using the Tukey honestly significant difference test (α=.05). RESULTS: Mean ± SD failure loads for groups ranged from 791.1 ± 177.5 N to 1086.1 ± 181.1 N. One-way ANOVA revealed a statistically significant difference between the groups (P ≤ .05). However, no statistically significant differences were observed among groups (P > .05), except between GHT (control group) and groups GBLF and GWF (P = .025, P = .022). CONCLUSIONS: Within the limitations of this study, the location of the ferrule had no significant effect on the fracture resistance of endodontically treated mandibular premolars.