A Selective and Sensitive Method Development and Validation of 1,1-Dimethyl-3-Hydroxy-Pyrrolidinium Bromide Impurity in Glycopyrrolate Oral Solution by Liquid Chromatography-Tandem Mass Spectroscopy.

OBJECTIVE: A selective and sensitive liquid chromatography-tandem mass spectrometer (LC-MS/MS) method has been developed for the quantification of 1,1-dimethyl-3-hydroxy-pyrrolidinium bromide impurity in glycopyrrolate oral solution. MATERIALS AND METHOD: The LC-MS/MS analysis was done on X Bridge HILIC (100 × 4.6 mm, 5 µm) analytical column, and the mobile phase used was10 mM ammonium formate with 0.2% formic acid as mobile phase-A and acetonitrile as mobile phase-B with a gradient programme of 5.0 min. The flow rate used was 1.2 mL/min. Triple quadrupole mass detector coupled to positive electrospray ionization operated in multiple reactions monitoring mode was used for the quantification at m/z 116.10 ± 0.5. RESULTS: Retention time of impurity was found ~3.2 min. The method was validated in terms of specificity, linearity, accuracy, precision, range, limit of detection, limit of quantitation (LOQ) and robustness. Relative standard deviation (RSD) for system suitability was found 1.3%. Calibration plot was linear over the range of 0.050-2.000 µg/mL. Limit of detection and limit of quantification were found 0.017 and 0.051 µg/mL, respectively. The intra- and inter-day precision RSD was 2.3% and the obtained recovery at LOQ to 200% was in between 86.7 and 107.4%. CONCLUSION: The low RSD values and high recoveries of the method confirm the suitability of the method.

Synthesis of C-14 labeled Rac-(3R,2S)-glycopyrronium bromide.

In an effort to better understand the drug metabolism and pharmacokinetics (DMPK) properties of glycopyrronium bromide (1), a muscarinic acetylcholine receptor antagonist, a C-14 labeled isotopologue was required. The compound was prepared in five synthetic steps and 5% overall radiochemical yield from Cu14 CN. During the synthesis, an unexpected decarboxylation of phenylglyoxylate resulted in the loss of much of the radiolabeled compound. Chiral chromatography was utilized to isolate and deliver the proper pair of enantiomers as [14 C]-1.

HPTLC Method for Determination of R, R-Glycopyrronium Bromide and its Related Impurities.

An innovative high-performance thin layer chromatographic (HPTLC) method was designed, optimized and validated for the quantification of R, R-glycopyrronium bromide (GLY) and its related impurities in drug substance and drug product. Separation was performed on HPTLC plates pre-coated with silica gel 60 F254 by dichloromethane:methanol:formic acid (10:0.5:0.5, v/v/v) as a developing system. GLY and its related impurities namely, glycopyrronium impurity G and glycopyrronium impurity J, were separated giving compact well-resolved spots with significant retardation factor (Rf) values of 0.17 ± 0.02, 0.34 ± 0.02 and 0.69 ± 0.02, respectively. Quantification was done at 220 nm in the ranges of 0.3-10 and 0.2-4.0 µg/spot with limits of detection and quantification of 0.1, 0.3 and 0.05, 0.2 µg/spot for GLY and its related impurities, respectively. Good accuracy was obtained with mean percentage recovery of 99.48 ± 1.36, 100.04 ± 1.32 and 99.61 ± 0.80 and R2 ≥ 0.9968 for GLY and its impurities, consecutively. Validation parameters were presented according to the International Conference on Harmonization. The method was used to investigate impurity profile of GLY in drug substance and drug product and could be applied in routine analysis of the drug. Comparison between the developed method and the reported method revealed no statistical difference.

New developments in optimizing bronchodilator treatment of COPD: a focus on glycopyrrolate/formoterol combination formulated by co-suspension delivery technology.

COPD causes considerable health and economic burden worldwide, with incidence of the disease expected to continue to rise. Inhaled bronchodilators, such as long-acting muscarinic antagonists (LAMAs) and long-acting ß2-agonists (LABAs), are central to the maintenance treatment of patients with COPD. Clinical studies have demonstrated that combined LAMA + LABA therapies improve efficacy while retaining a safety profile similar to LAMA or LABA alone. This has led to the development of several LAMA/LABA fixed-dose combination (FDC) therapies, which provide patients with the convenience of two active compounds in a single inhaler. GFF MDI (Bevespi Aerosphere®) is an FDC of glycopyrrolate/formoterol fumarate 18/9.6 µg formulated using innovative co-suspension delivery technology for administration via metered dose inhaler (MDI). GFF MDI was developed to make a treatment option available for patients who have a requirement or preference to use an MDI, rather than a dry powder or soft mist inhaler. Now that several LAMA/LABA FDCs have been approved for use in COPD, we review the impact of dual-bronchodilator treatment on COPD therapy and discuss recent clinical studies that are helping to develop a more comprehensive understanding of how LAMA/LABA FDCs can improve patient outcomes.

Validated ion pair chromatographic method for simultaneous determination and in vitro dissolution studies of indacaterol and glycopyrronium from inhaled capsule dosage form.

A rapid, and highly sensitive analytical method were developed for the simultaneous determination of indacaterol maleate (IND) and glycopyrronium bromide (GLY) in their inhaler capsules. Valid ion-pairing chromatographic (IPC) method was performed for separation of GLY in presence of IND using C18 column and mobile phase consisting of acetonitrile: acidified deionized water (60:40% v/v) containing 0.02% sodium dodecyl sulfate (SDS) adjusted to pH 3.0 using OPA (orthophosphoric acid) isocratically eluted at 2.0 mL/min. Quantitation was achieved with UV detection at 210 nm. Cyproheptadine was used as an internal standard. The retention times were 1.9 and 2.5 min for IND, and GLY, respectively. For the IPC method, the calibration graphs were linear in the range of 0.66-66.0 µg/mL for IND and 0.3-30.0 µg/mL for GLY. The proposed method are rapid, reproducible (R.S.D. <2.0%) and achieves satisfactory resolution between IND and GLY (resolution factor = 4.23). The mean recoveries of the analytes in their inhaler capsule were satisfactory. It was applied successfully to in vitro dissolution testing using Franz diffusion cell and extended to a content uniformity test consistent with the United States Pharmacopoeia (USP) guidelines and were found to be precise and accurate for the capsules studied with acceptance value of 4.53 and 1.39 for IND and GLY, respectively.

Dose-response of an extrafine dry powder inhaler formulation of glycopyrronium bromide: randomized, double-blind, placebo-controlled, dose-ranging study (GlycoNEXT).

Introduction: An extrafine formulation of the long-acting muscarinic antagonist, glycopyrronium bromide (GB), has been developed for delivery via the NEXThaler dry powder inhaler (DPI). This study assessed the bronchodilator efficacy and safety of different doses of this formulation in patients with COPD to identify the optimal dose for further development. Patients and methods: This was a multicenter, randomized, double-blind, placebo-controlled, incomplete block, three-way crossover study, including three 28-day treatment periods, each separated by a 21-day washout period. Eligible patients had a diagnosis of COPD and post-bronchodilator forced expiratory volume in 1 s (FEV1) 40%-70% predicted. Treatments administered were GB 6.25, 12.5, 25 and 50 µg or matched placebo; all were given twice daily (BID) via DPI, with spirometry assessed on Days 1 and 28 of each treatment period. The primary end point was FEV1 area under the curve from 0 to 12 h (AUC0-12 h) on Day 28. Results: A total of 202 patients were randomized (61% male, mean age 62.6 years), with 178 (88%) completing all the three treatment periods. For the primary end point, all the four GB doses were superior to placebo (p<0.001) with mean differences (95% CI) of 114 (74, 154), 125 (85, 166), 143 (104, 183) and 187 (147, 228) mL for GB 6.25, 12.5, 25 and 50 µg BID, respectively. All four GB doses were also statistically superior to placebo for all secondary efficacy end points, showing clear dose-response relationships for most of the endpoints. Accordingly, GB 25 µg BID met the criteria for the minimally acceptable dose. Adverse events were reported by 15.5, 16.2, 10.9 and 14.3% of patients receiving GB 6.25, 12.5, 25 and 50 µg BID, respectively, and 14.8% receiving placebo. Conclusion: This study supports the selection of GB 25 µg BID as the minimal effective dose for patients with COPD when delivered with this extrafine DPI formulation.

Dispersive micro-solid-phase extraction combined with online preconcentration by capillary electrophoresis for the determination of glycopyrrolate stereoisomers in rat plasma.

A simple and sensitive analytical method for four isomers of glycopyrrolate in rat plasma was developed using cation-selective exhaustive injection-sweeping cyclodextrin-modified electrokinetic chromatography (CSEI-Sweeping-CDEKC) for online enrichment combined with dispersive micro-solid-phase extraction pretreatment. The CSEI-Sweeping-CDEKC was conducted on an uncoated fused silica capillary (40.2 cm × 75 µm) with an applied voltage of -20 kV. The electrophoretic analysis was carried out in 30 mM phosphate solution at pH 2.0 containing 20 mg/mL sulfated-ß-cyclodextrin and 5% acetonitrile. Under these optimized conditions, the detection limit for racemic glycopyrrolate was found to be 2.0 ng/mL and this method could increase 495-fold detection sensitivity compared with the traditional injection method. Additionally, the parameters that affected the extraction efficiency of dispersive micro-solid-phase extraction were also examined systematically. The glycopyrrolate isomers in rat plasma samples as low as 0.0625 µg/mL were able to be separated and detected by capillary electrophoresis with the aid of CSEI-sweeping. The findings of this study show that the dispersive micro-solid-phase extraction pretreatment coupled with CSEI-Sweeping-CDEKC is a rapid and convenient method for analyzing glycopyrrolate isomers in rat plasma.

Role of nebulized glycopyrrolate in the treatment of chronic obstructive pulmonary disease.

In the upcoming years, the proportion of elderly patients with chronic obstructive pulmonary disease (COPD) will increase, according to the progressively aging population and the increased efficacy of the pharmacological treatments, especially considering the management of chronic comorbidities. The issue to prescribe an appropriate inhalation therapy to COPD patients with significant handling or coordination difficulties represents a common clinical experience; in the latter case, the choice of an inadequate inhalation device may jeopardize the adherence to the treatment and eventually lead to its ineffectiveness. Treatment options that do not require particular timing for coordination between activation and/or inhalation or require high flow thresholds to be activated should represent the best treatment option for these patients. Nebulized bronchodilators, usually used only in acute conditions such as COPD exacerbations, could fulfill this gap, enabling an adequate drug administration during tidal breathing and without the need for patients' cooperation. However, so far, only short-acting muscarinic antagonists have been available for nebulization. Recently, a nebulized formulation of the inhaled long-acting muscarinic antagonist glycopyrrolate, delivered by means of a novel proprietary vibrating mesh nebulizer closed system (SUN-101/eFlow®), has progressed to Phase III trials and is currently in late-stage development as an option for maintenance treatment in COPD. The present critical review describes the current knowledge about the novel nebulizer technology, the efficacy, safety, and critical role of nebulized glycopyrrolate in patients with COPD. To this end, PubMed, ClinicalTrials.gov, Embase, and Cochrane Library have been searched for relevant papers. According to the available results, the efficacy and tolerability profile of nebulized glycopyrrolate may represent a valuable and dynamic treatment option for the chronic pharmacological management of patients with COPD.

Bronchodilator efficacy of extrafine glycopyrronium bromide: the Glyco 2 study.

An extrafine formulation of the long-acting muscarinic antagonist glycopyrronium bromide (GB) is in development for chronic obstructive pulmonary disease (COPD), in combination with beclometasone dipropionate and formoterol fumarate - a "fixed triple". This two-part study was randomized, double blind, placebo controlled in patients with moderate-to-severe COPD: Part 1: single-dose escalation, GB 12.5, 25, 50, 100 or 200 µg versus placebo; Part 2: repeat-dose (7-day), four-period crossover, GB 12.5, 25 or 50 µg twice daily (BID) versus placebo, with an open-label extension in which all patients received tiotropium 18 µg once daily. On the morning of Day 8 in all five periods, patients also received formoterol 12 µg. In study Part 1, 27 patients were recruited. All GB doses significantly increased from baseline forced expiratory volume in 1 second (FEV1) area under the curve (AUC0-12h) and peak FEV1, with a trend toward greater efficacy with higher GB dose. All adverse events were mild-moderate in severity, with a lower incidence with GB than placebo and no evidence of a dose-response relationship. In study Part 2, of 38 patients recruited, 34 completed the study. Adjusted mean differences from placebo in 12 h trough FEV1 on Day 7 (primary) were 115, 142 and 136 mL for GB 12.5, 25 and 50 µg BID, respectively (all P<0.001). GB 25 and 50 µg BID were superior (P<0.05) to GB 12.5 µg BID for pre-dose morning FEV1 on Day 8. For this endpoint, GB 25 and 50 µg BID were also superior to tiotropium. Compared with Day 7, addition of formoterol significantly increased Day 8 FEV1 peak and AUC0-12h with all GB doses and placebo (all P<0.001). All adverse events were mild-moderate in severity and there was no indication of a dose-related relationship. This study provides initial evidence on bronchodilation, safety and pharmacokinetics of extrafine GB BID. Overall, the results suggest that GB 25 µg BID is the optimal dose in patients with COPD.

Long-term Stability of Zonisamide, Amitriptyline, and Glycopyrrolate in Extemporaneously Prepared Liquid-dosage Forms at Two Temperatures.

The lack of commercially available liquid dosage forms for pediatric patients prompted this study. The objectives of our study were to determine the stability of zonisamide, amitriptyline, and glycopyrrolate in extemporaneously prepared oral suspensions in plastic prescription bottles. One group of suspensions was prepared in OraPlus:OraSweet (1:1) for each drug and stored either under refrigeration (4°C) or at room temperature (25°C). A second group of suspensions were compounded in 1% methylcellulose:simple syrup at a 1:10 proportion for zonisamide, amitriptyline, and glycopyrrolate; these suspensions were stored at either under refrigeration (4°C) or at room temperature (25°C). The drug concentrations were measured by the stability-indicating high-performance liquid chromatographic methods. The mean concentration of zonisamide (10 mg/mL) remained above 95% of the original concentration for 91 days in each group of suspensions at both 4°C and 25°C. The mean concentration of amitriptyline (20 mg/mL) was above 95% for 91 days in the suspensions containing OraPlus/ OraSweet at both 4°C and 25°C. However, in the suspensions containing methylcellulose:simple syrup, the mean concentration of amitriptyline was about 95% for 42 days at 4°C and 28 days at 25°C. The mean concentration of glycopyrrolate (0.2 mg/mL) was above 95% in each group of suspensions during the 14-day study period. These data indicate that zonisamide, amitriptyline, and glycopyrrolate can be prepared extemporaneously as suspensions and stored in plastic prescription bottles for varying periods at 4°C and 25°C for use in pediatric patients.

Isothermal microcalorimetry of pressurized systems II: effect of excipient and water ingress on formulation stability of amorphous glycopyrrolate.

PURPOSE: Use isothermal microcalorimetry to directly evaluate the effects of excipients and water content to produce a stable amorphous glycopyrrolate pressurized metered dose inhaler (pMDI) formulation. METHODS: Amorphous glycopyrrolate particles with and without excipients (Distearoyl-sn-glycero-3-phosphatidylcholine (DSPC) or ß-cyclodextrin (ßCD)) were spray dried and cold filled along with HFA 134a into customized thermal activity monitor (TAM) measurement ampoules. When applicable, a known amount of water was also pipetted into the ampoule. Sample ampoules were hermetically sealed, equilibrated to 25°C and measured isothermally for at least 24 h using the TAM III (TA Instruments, Sollentuna, Sweden). RESULTS: Amorphous glycopyrrolate particles were highly unstable and crystallized rapidly when suspended in HFA 134a. Co-spray drying the glycopyrrolate with DSPC failed to mitigate this instability, but co-spray drying with ßCD protected the amorphous glycopyrrolate from crystallization, resulting in a stable formulation at low water contents (≤ 100 ppm). CONCLUSIONS: This study shows that isothermal microcalorimetry can easily differentiate between physically stable and unstable pMDI formulations of glycopyrrolate within a few hours. Furthermore, it allows rapid screening of various formulation factors (drug form, excipients, water ingress), which can greatly reduce the time required to develop marketable products with acceptable shelf life.

Determination of the enantiomeric and diastereomeric impurities of RS-glycopyrrolate by capillary electrophoresis using sulfated-ß-cyclodextrin as chiral selectors.

A practical chiral CE method, using sulfated-ß-CD as chiral selector, was developed for the enantioseparation of glycopyrrolate containing two chiral centers. Several parameters affecting the separation were studied, including the nature and concentration of the chiral selectors, BGE pH, buffer type and concentration, separation voltage, and temperature. The separation was carried out in an uncoated fused-silica capillary of (effective length 40 cm) × 50 µm id with a separation voltage of 20 kV using 30 mM sodium phosphate buffer (pH 7.0, adjusted with 1 M sodium hydroxide) containing 2.0% w/v sulfated-ß-CD at 25°C. Finally, the method for determining the enantiomeric impurities of RS-glycopyrrolate was proposed. The method was further validated with respect to its specificity, linearity range, accuracy and precision, LODs, and quantification in the expected range of occurrence for the isomeric impurities (0.1%).

Cosuspensions of microcrystals and engineered microparticles for uniform and efficient delivery of respiratory therapeutics from pressurized metered dose inhalers.

Engineered porous phospholipid microparticles with aerodynamic diameters in the respirable range of 1-2 µm were cosuspended in 1,1,1,2-tetrafluoroethane, a propellant, with microcrystals of glycopyrrolate, formoterol fumarate dihydrate, or Mometasone furoate-three drugs with different solubilities in the propellant, and different physical, chemical, and pharmacological attributes. The drug microcrystals were added individually, in pairs, or all three together to prepare different cosuspensions, contained in a pressurized metered dose inhaler (pMDI). The drug microcrystals irreversibly associated with the porous particles, and the resultant cosuspensions possessed greatly improved suspension stability compared with suspensions of drug microcrystals alone. In general, all cosuspensions showed efficient dose delivery of the drugs, with fine particle fractions of more than 60% for a wide range of doses, including those as low as 300 ng per inhaler actuation. In the cosuspension pMDIs, comparable fine particle fractions were delivered for all tested drugs, whether or not they were emitted from an inhaler containing one, two, or three drugs. We demonstrate that the cosuspension approach solves at least three long-standing problems in the clinical development of pMDI-based products: (1) dose and drug dependent delivery efficiency, (2) inability to formulate dose strengths below 1 µg to fully explore drug efficacy and safety, and (3) combination suspensions delivering a different fine particle fraction than individual drug suspensions.

Stability of extemporaneously prepared glycopyrrolate oral suspensions.

PURPOSE: The stability of extemporaneously prepared glycopyrrolate 0.5-mg/mL suspensions was evaluated. METHODS: An oral suspension of glycopyrrolate 0.5 mg/mL was prepared by thoroughly grinding 30 1-mg tablets of glycopyrrolate in a glass mortar. Thirty milliliters of Ora-Plus and 30 mL of either Ora-Sweet or Ora-Sweet SF were mixed and added to the powder to make a final volume of 60 mL. Three identical samples of the formulation were prepared and placed in 2-oz amber plastic bottles with child-resistant caps and stored at room temperature (23-25 °C). A 1-mL sample was withdrawn from each of the three bottles with a micropipette immediately after preparation and 7, 15, 30, 60, and 90 days afterward. After further dilution to an expected concentration of 50 µg/mL with sample diluent, the samples were assayed in duplicate by stability-indicating high-performance liquid chromatography. The samples were visually examined for any color change and evaluated for pH on each day of analysis. Taste evaluations were performed at the beginning and end of the study. Stability was defined as the retention of at least 90% of the initial concentration. RESULTS: At least 95% of the initial glycopyrrolate remained throughout the 90-day study period in both preparations. There were no detectable changes in color, odor, taste, and pH, and no visible microbial growth was observed in any sample. CONCLUSION: Extemporaneously compounded suspensions of glycopyrrolate 0.5 mg/mL in a 1:1 mixture of Ora-Plus/Ora-Sweet or Ora-Plus/Ora-Sweet SF were stable for at least 90 days when stored in amber plastic bottles at room temperature.

Soft quaternary anticholinergics: comprehensive quantitative structure-activity relationship (QSAR) with a linearized biexponential (LinBiExp) model.

A comprehensive quantitative structure-activity relationship (QSAR) study is presented for quaternary soft anticholinergics including two distinctly different classes designed on the basis of the soft analogue and the inactive metabolite approaches. Because of the clear biphasic (bilinear) nature of the activity data when all structures (n = 76) were considered as a function of molecular size (volume), a nonlinear model had to be used, and a linearized biexponential (LinBiExp) model proved very adequate. LinBiExp can fit activity data that show a maximum (or a minimum) around a given parameter value but tend to show linearity away from this turning point. Contrary to Hansch-type parabolic models, LinBiExp represents a natural extension of linear models, and a direct correspondence between its parameters and those obtained earlier by linear regression on compound subsets covering more limited parameter ranges could be easily established. Stereospecificity was confirmed as important, and the presence of an acid moiety was found to essentially eliminate activity. The consideration of bilinear behavior, which most likely results from size limitations at the binding site, can also explain the embarrassingly low activity found for a relatively large compound predicted as highly active by Lien, Ariëns, and co-workers based on their QSAR study.