RESUMEN
Synthetic leather samples from Brazil and Paraguay were evaluated in this study using three spectroscopy techniques: inductively coupled plasma optical emission spectrometry (ICP-OES), laser-induced breakdown spectroscopy (LIBS), and wavelength dispersive X-ray fluorescence (WDXRF). The obtained information from each technique was separately inspected with principal component analysis (PCA). The concentrations of the elements determined in the synthetic leathers using ICP-OES decreased in the following order: Ca > Cr > Mg > Ba > Pb > Al > Fe > Zn > Sb > Ni with a concentration range below the limit of quantification (Asunto(s)
Materiales Manufacturados/análisis
, Metales/análisis
, Análisis Espectral/métodos
, Brasil
, Rayos Láser
, Límite de Detección
, Paraguay
, Análisis de Componente Principal
, Espectrometría por Rayos X/métodos
, Análisis Espectral/estadística & datos numéricos
RESUMEN
Tunability of the optical response of multilayered photonic structures has been compared with sequential (SQ) and superposition (SP) addition of refractive index profile functions. The optical response of the composite multilayered structure, formed after the SP addition of the two Bragg type refractive index profile functions has been studied as a function of percentage overlap and relative shift between the profiles. Apart from the substantial advantage in terms of the reduced physical thickness of the SP composite structures (over the SQ addition), at certain optimum values of relative shift, photonic structures with better quality factor resonant modes or a broader PBG could be designed. Similar analysis has been extended for rugate filters as well. The experimental verification of the optical response, was carried out through multilayered dielectric porous silicon structures fabricated by electrochemical anodization.
Asunto(s)
Materiales Manufacturados/análisis , Modelos Teóricos , Simulación por Computador , Luz , Dispersión de RadiaciónRESUMEN
In this report, we investigate the polarization effect (linear, elliptical and circular) on the two-photon absorption (2PA) properties of a chiral compound based in azoaromatic moieties using the femtosecond Z-scan technique with low repetition rate and low pulse energy. We observed a strong 2PA modulation between 800 nm and 960 nm as a function the polarization changes from linear through elliptical to circular. Such results were interpreted employing the sum-over-essential states approach, which allowed us to model the 2PA circular-linear dichroism effect and to identifier the overlapping of the excited electronic states responsible by the 2PA allowed band.
Asunto(s)
Dicroismo Circular/métodos , Materiales Manufacturados/análisis , Modelos Químicos , Fotones , Refractometría/métodos , Absorción , Simulación por Computador , LuzRESUMEN
The main objective of this study was to carry out a direct performance comparison among some known types of TLDs-three types of CaSO(4):Dy pellets, sintered Al(2)O(3) pellets, LiF:Mg,Ti (Harshaw TLD-100), CaF(2):Dy (Harshaw TLD-200) and CaF(2):Mn (Harshaw TLD-400)-in the energy and dose ranges of diagnostic radiology beams. Several dosimetric characteristics were evaluated, such as reproducibility, sensitivity, calibration curves, lower dose limits and energy dependence.
Asunto(s)
Materiales Manufacturados/análisis , Dosimetría Termoluminiscente/instrumentación , Tomografía Computarizada por Rayos X/métodos , Diseño de Equipo , Análisis de Falla de Equipo , Ensayo de Materiales , Dosis de Radiación , Reproducibilidad de los Resultados , Sensibilidad y Especificidad , Rayos XRESUMEN
Gamma ray tomography experiments have been carried out to detect spatial patterns in the porosity in a 0.27 m diameter column packed with steel Rashig rings of different sizes: 12.6, 37.9, and 76 mm. using a first generation CT system (Chen et al., 1998). A fast Fourier transform tomographic reconstruction algorithm has been used to calculate the spatial variation over the column cross section. Cross-sectional gas porosity and solid holdup distribution were determinate. The values of cross-sectional average gas porosity were epsilon=0.849, 0.938 and 0.966 for the 12.6, 37.9, and 76 mm rings, respectively. Radial holdup variation within the packed bed has been determined. The variation of the circumferentially averaged gas holdup in the radial direction indicates that the porosity in the column wall region is a somewhat higher than that in the bulk region, due to the effect of the column wall.
Asunto(s)
Algoritmos , Materiales Manufacturados/análisis , Ensayo de Materiales/métodos , Espectrometría gamma/métodos , PorosidadRESUMEN
The properties of the thermally stimulated exoelectron emission (TSEE) and thermoluminescent (TL) emission of topaz-glass composites were studied with the aim of using them as solid-state dosemeters. The TSEE response was studied as a function of radiation energy and as a function of absorbed dose. Topaz-glass composites presented a linear TL and TSEE response to dose within a range of 0.01-1 Gy. The topaz-glass composites presented higher TSEE peaks than topaz-Teflon pellets. In the dosimetry of radiotherapic fields normally the responses of the topaz-glass dosemeters are comparable to topaz-Teflon pellets. The results confirmed that these new dosemeters can be useful in monitoring the quality of the radiation sources. This dose mapping technique is particularly useful in investigating dose distribution throughout a planned target volume.
Asunto(s)
Vidrio/química , Vidrio/efectos de la radiación , Modelos Químicos , Cementos de Resina/química , Cementos de Resina/efectos de la radiación , Dosimetría Termoluminiscente/instrumentación , Dosimetría Termoluminiscente/métodos , Simulación por Computador , Relación Dosis-Respuesta en la Radiación , Diseño de Equipo , Análisis de Falla de Equipo , Materiales Manufacturados/análisis , Ensayo de Materiales , Dosis de RadiaciónRESUMEN
Laser-induced breakdown spectroscopy (LIBS) was used for the characterization of the main components of the surface residual dirt produced in cold-rolled steel plates as a consequence of the manufacturing stages. At laser fluences between 0.05 J/cm(2) < F < 0.30 J/cm(2), dirt ablation takes place without any contribution from the substrate. Results show that the main components of the dirt are fine particles of Fe mostly homogeneously distributed in a thin layer of grease and soaps. In the primary stages of the manufacturing process carbon residuals can also be found. By measuring light emission from the lambda = 495.9 nm line of Fe(I) after laser ablation, we developed a real-time on-line method for the determination of the concentration of iron particles present in the surface dirt. The obtained results open new possibilities in the design of real-time instruments for industrial applications as a quality control of products and processes.
Asunto(s)
Polvo/análisis , Rayos Láser , Materiales Manufacturados/análisis , Suelo/análisis , Análisis Espectral/instrumentación , Acero/análisis , Acero/química , Polvo/prevención & control , Contaminación de Equipos/prevención & control , Diseño de Equipo , Análisis de Falla de Equipo , Reproducibilidad de los Resultados , Sensibilidad y Especificidad , Análisis Espectral/métodosRESUMEN
It is not rare to hear arguments against the use of thermocouples for taking temperatures in processes that are taking place under microwave fields. However, the simplicity of this device makes it attractive to consider its use. One question that arises when thermocouples are employed is whether the electric field perturbs the measurement, and if the thermocouple affects the processing. The process that was chosen for conducting this test was the synthesis of spinel (MgAl2O4) using microwaves as a power supply and hematite (Fe2O3) as an additive for both spinel formation promotion and susceptor. The alumina-based systems are very important to study because this is one of the most common ingredients in refractory materials. There are many discussions about the improvement of the process when microwaves are used, but a kinetic comparison cannot be performed if the temperature is unknown, and that is the reason for emphasizing the measurement techniques. The analysis of the obtained samples was carried out by X-ray diffraction of powders. The results of this work show that there is no difference between the products obtained when the thermocouple was inserted in the system, compared to processing without it; hence the thermocouple is appropriate for this application.
Asunto(s)
Cerámica/análisis , Cerámica/química , Microondas , Termografía/instrumentación , Termografía/métodos , Transductores , Artefactos , Cerámica/efectos de la radiación , Análisis de Falla de Equipo , Materiales Manufacturados/análisis , Materiales Manufacturados/efectos de la radiación , Ensayo de Materiales , Reproducibilidad de los Resultados , Sensibilidad y EspecificidadRESUMEN
This work presents the results of the determination of uranium concentration in the most commonly used phosphate fertilizers employed in Brazilian agricultural land. The technique employed was the nuclear fission track registration in plastic foils of Makrofol KG (dry method), together with a discharge chamber system for track counting. Phosphate fertilizer samples and uranium standards were irradiated together with thermal neutrons in the 2 MW IEA-R1 research reactor of IPEN/SP. The uranium concentration in Brazilian phosphate fertilizers ranging from 5.17 to 54.3 ppm is in good agreement with the results reported in the literature for similar fertilizers produced in other countries.