Pollution characteristics and quantitative source apportionment of heavy metals within a zinc smelting site by GIS-based PMF and APCS-MLR models.

The abandoned smelters present a substantial pollution threat to the nearby soil and groundwater. In this study, 63 surface soil samples were collected from a zinc smelter to quantitatively describe the pollution characteristics, ecological risks, and source apportionment of heavy metal(loid)s (HMs). The results revealed that the average contents of Zn, Cd, Pb, As, and Hg were 0.4, 12.2, 3.3, 5.3, and 12.7 times higher than the risk screening values of the construction sites, respectively. Notably, the smelter was accumulated heavily with Cd and Hg, and the contribution of Cd (0.38) and Hg (0.53) to ecological risk was 91.58%. ZZ3 and ZZ7 were the most polluted workshops, accounting for 25.7% and 35.0% of the pollution load and ecological risk, respectively. The influence of soil parent materials on pollution was minor compared to various workshops within the smelter. Combined with PMF, APCS-MLR and GIS analysis, four sources of HMs were identified: P1(25.5%) and A3(18.4%) were atmospheric deposition from the electric defogging workshop and surface runoff from the smelter; P2(32.7%) and A2(20.9%) were surface runoff of As-Pb foul acid; P3(14.5%) and A4(49.8%) were atmospheric deposition from the leach slag drying workshop; P4(27.3%) and A1(10.8%) were the smelting process of zinc products. This paper described the distribution characteristics and specific sources of HMs in different process workshops, providing a new perspective for the precise remediation of the smelter by determining the priority control factors.

Assessing the Impact of PM2.5-Bound Arsenic on Cardiovascular Risk among Workers in a Non-ferrous Metal Smelting Area: Insights from Chemical Speciation and Bioavailability.

Inhalation of fine particulate matter PM2.5-bound arsenic (PM2.5-As) may cause significant cardiovascular damage, due to its high concentration, long transmission range, and good absorption efficiency in organisms. However, both the contribution and the effect of the arsenic exposure pathway, with PM2.5 as the medium, on cardiovascular system damage in nonferrous smelting sites remain to be studied. In this work, a one-year site sample collection and analysis work showed that the annual concentration of PM2.5-As reached 0.74 µg/m3, which was 120 times the national standard. The predominant species in the PM2.5 samples were As (V) and As (III). A panel study among workers revealed that PM2.5-As exposure dominantly contributed to human absorption of As. After exposure of mice to PM2.5-As for 8 weeks, the accumulation of As in the high exposure group reached equilibrium, and its bioavailability was 24.5%. A series of animal experiments revealed that PM2.5-As exposure induced cardiac injury and dysfunction at the environmental relevant concentration and speciation. By integrating environmental and animal exposure assessments, more accurate health risk assessment models exposed to PM2.5-As were established for metal smelting areas. Therefore, our research provides an important scientific basis for relevant departments to formulate industry supervision, prevention and control policies.

Eco-Friendly Inorganic Binders: A Key Alternative for Reducing Harmful Emissions in Molding and Core-Making Technologies.

Many years of foundry practice and much more accurate analytical methods have shown that sands with organic binders, in addition to their many technological advantages, pose risks associated with the emission of many compounds, including harmful ones (e.g., formaldehyde, phenol, benzene, polycyclic aromatic hydrocarbons, and sulfur), arising during the pouring of liquid casting alloys into molds, their cooling, and knock-out. The aim of this research is to demonstrate the potential benefits of adopting inorganic binders in European iron foundries. This will improve the environmental and working conditions by introducing cleaner and more ecological production methods, while also ranking the tested binders studied in terms of their harmful content. The article pays special attention to the analysis of seven innovative inorganic binders and one organic binder, acting as a reference for emissions of gases from the BTEX (benzene, toluene, ethylbenzene, and xylenes) and PAHs (polycyclic aromatic hydrocarbons) groups and other compounds such as phenol, formaldehyde, and isocyanates (MDI and TDI) generated during the mold pouring process with liquid metals. The knowledge gained will, for the first time, enrich the database needed to update the Reference Document on The Best Available Techniques for the Smitheries and Foundries Industry (SF BREF).

Distinguishing the contributions of different smelting emissions to the spatial risk footprints of toxic elements in soil using PMF, Bayesian isotope mixing models, and distance-based regression.

Toxic element pollution of soils emanating from smelting operations is an escalating global concern due to its severe impact on ecosystems and human health. In this study, soil samples were collected and analyzed to quantify the risk contributions and delineate the spatial risk footprints from smelting emissions for 8 toxic elements. A comprehensive health risk contribution and delineation framework was utilized, consisting of Positive matrix factorization (PMF), spatial interpolation, an advanced Bayesian isotope mixing model via Mixing Stable Isotope Analysis in R (MixSIAR), and distance-based regression. The results showed that the mean concentrations of As, Cd, Cu, Hg, Pb, and Zn exceeded the background levels, indicating substantial contamination. Three sources were identified using the PMF model and confirmed by spatial interpolation and MixSIAR, with contributions ranked as follows: industrial wastewater discharge and slag runoff from the smelter site (48.9 %) > natural geogenic inputs from soil parent materials (26.7 %) > atmospheric deposition of dust particles from smelting operations (24.5 %). Among the identified sources, smelter runoff posed the most significant risk, accounting for 97.9 % of the non-carcinogenic risk (NCR) and 59.9 % of the carcinogenic risk (CR). Runoff also drove NCR and CR exceedances at 7.8 % and 4.7 % of sites near the smelter, respectively. However, atmospheric deposition from smelting emissions affected soils across a larger 0.8 km radius. Although it posed lower risks, contributing just 1.1 % to NCR and 22.6 % to CR due to the limited elevation of toxic elements, deposition reached more distant soils. Spatial interpolation and distance-based regression delineated high NCR and CR exposure hotspots within 1.4 km for runoff and 0.8 km for deposition, with exponentially diminishing risks at further distances. These findings highlight the need for pathway-specific interventions that prioritize localized wastewater containment and drainage controls near the smelter while implementing broader regional air pollution mitigation measures.

Differentiating anthropogenic effects from natural metal(loid) levels in residential soil near a zinc smelter in South Korea.

Metal(loid)s pose a significant hazard due to inherent toxicity. Individuals are particularly exposed to metal(loid)s in soil through direct or indirect contact. Identifying metal(loid) sources in soil is required for exposure mitigation to anthropogenic metal(loid)s, while metal(loid)s are natural constitutes of soil. Metal(loid) concentrations and Pb isotopes were determined in residential soil profiles impacted by a Zn smelter to distinguish the anthropogenic effect from natural levels. One hundred sixty-nine core soil samples were collected from depths down to 5.5 m below ground level at 19 sites and were divided into Zn-Cd-As- and As-contaminated groups based on the worrisome level (WL) of soil contamination. The Zn-Cd-As-contaminated group (n = 62) was observed at depths < 1 m, showed high Zn levels (mean of 1168 mg/kg) and Cd and As frequently exceeding WLs, and had low 206Pb/207Pb ratios close to the Zn smelter. In contrast, the As-contaminated group (n = 96) was observed at depths > 1 m, did not have other metals exceeding WLs, and showed a wide range of 206Pb/207Pb ratios far away from the Zn smelter. The results indicated that the pollution sources of Zn-Cd-As- and As-contaminated soils were fugitive dust emissions from smelter stacks and geology, respectively. The metal(loid)s in host rock set geochemical baselines in soil profiles, while smelting activities affected the upper layers over 50 years. This study demonstrated the effectiveness of utilizing the vertical distribution of metal(loid) concentrations and Pb isotopes in soil profiles for distinguishing between anthropogenic and geogenic origins, in combination with baseline assessment.

Techno-economic assessment of bioleaching for metallurgical by-products.

This study focused on the economic feasibility of two potential industrial-scale bioleaching technologies for metal recovery from specific metallurgical by-products, mainly basic oxygen steelmaking dust (BOS-D) and goethite. The investigation compared two bioleaching scaling technology configurations, including an aerated bioreactor and an aerated and stirred bioreactor across different scenarios. Results indicated that bioleaching using Acidithiobacillus ferrooxidans proved financially viable for copper extraction from goethite, particularly when 5% and 10% pulp densities were used in the aerated bioreactor, and when 10% pulp density was used in the aerated and stirred bioreactor. Notably, a net present value (NPV) of $1,275,499k and an internal rate of return (IRR) of 65% for Cu recovery from goethite were achieved over 20-years after project started using the aerated and stirred bioreactor plant with a capital expenditure (CAPEX) of $119,816,550 and an operational expenditure (OPEX) of $5,896,580/year. It is expected that plant will start to make profit after one year of operation. Aerated and stirred bioreactor plant appeared more reliable alternative compared to the aerated bioreactor plant as the plant consists of 12 reactors which can allow better management and operation in small volume with multiple reactors. Despite the limitations, this techno-economic assessment emphasized the significance of selective metal recovery and plant design, and underscored the major expenses associated with the process.

LCA of recycling aluminium incineration bottom ash, dross and shavings in a rotary furnace and environmental benefits of salt-slag valorisation.

Recycling aluminium in a rotary furnace with salt-fluxes allows recovering valuable alloys from hard-to-recycle waste/side-streams such as packaging, dross and incinerator bottom ash. However, this recycling route generates large amounts of salt-slag/salt-cake hazardous wastes which can pose critical environmental risks if landfilled. To tackle this issue, the metallurgical industry has developed processes to valorise the salt-slag residues into recyclable salts and aluminium concentrates, while producing by-products such as ammonium sulphate and non-metallic compounds (NMCs), with applications in the construction or chemical industries. This study aims to assess through LCA the environmental impacts of recycling aluminium in rotary furnaces for both salt-slag management routes: valorisation or landfill. It was found that this recycling process brings forth considerable net environmental profits, which increase for all the considered impact categories if the salt-slag is valorised. The main benefits arise from the production of secondary cast aluminium alloys, which is not unexpected due to the high energy intensity of aluminium primary production. However, the LCA results also identify other hotspots which play a significant role, and which should be considered for the optimisation of the process based on its environmental performance, such as the production of by-products, the consumption of energy/fuels and the avoidance of landfilling waste. Additionally, the assessment shows that the indicators for mineral resource scarcity, human carcinogenic toxicity and terrestrial ecotoxicity are particularly benefited by the salt-slag valorisation. Finally, a sensitivity analysis illustrates the criticality of the metal yield assumptions when calculating the global warming potential of aluminium recycling routes.

Effects of soil metal(loid)s pollution on microbial activities and environmental risks in an abandoned chemical smelting site.

Abandoned chemical smelting sites containing toxic substances can seriously threaten and pose a risk to the surrounding ecological environment. Soil samples were collected from different depths (0 to 13 m) and analyzed for metal(loid)s content and fractionation, as well as microbial activities. The potential ecological risk indices for the different soil depths (ordered from high to low) were: 1 m (D-1) > surface (S-0) > 5 m (D-5) > 13 m (D-13) > 9 m (D-9), ranging between 1840.65-13,089.62, and representing extremely high environmental risks, of which Cd (and probably not arsenic) contributed to the highest environmental risk. A modified combined pollution risk index (MCR) combining total content and mobile proportion of metal(loid)s, and relative toxicities, was used to evaluate the degree of contamination and potential environmental risks. For the near-surface samples (S-0 and D-1 layers), the MCR considered that As, Cd, Pb, Sb, and Zn achieved high and alarming degrees of contamination, whereas Fe, Mn, and Ti were negligible or low to moderate pollution degrees. Combined microcalorimetry and enzymatic activity measurements of contaminated soil samples were used to assess the microbial metabolic activity characteristics. Correlation analysis elucidated the relationship between metal(loid)s exchangeable fraction or content and microbial activity characteristics (p < 0.05). The microbial metabolic activity in the D-1 layer was low presumably due to heavy metal stress. Enzyme activity indicators and microcalorimetric growth rate (k) measurements were considered sensitive indicators to reflect the soil microbial activities in abandoned chemical smelting sites.

Atmospheric occurrences and bioavailability health risk of PAHs and their derivatives surrounding a non-ferrous metal smelting plant.

Non-ferrous metal smelting emits large amounts of organic compounds into the atmosphere. Herein, 20 parent polycyclic aromatic hydrocarbons (PPAHs), 9 nitrated PAHs (NPAHs), 14 chlorinated PAHs (ClPAHs), and 6 alkylated PAHs (APAHs) in atmospheric samples from a typical non-ferrous metal smelting plant (NMSP) and residential areas were detected. In NMSP, benzo[a]pyrene, dibenz[a,h]anthracene, 6-nitrochrysene, 9-chlorofluorene, and 1-methylfluorene were the predominant compounds in the particulate phase, while phenanthrene constituted 57.3% in the gaseous phase. The concentration of PAHs in residential areas around NMSP was 1.8 times higher than that in the control area. Additionally, there was a significant negative correlation between the concentration and the distance from the NMSP. In terms of health risks, although the skin penetration coefficient of PM2.5 is smaller than that of the gaseous phase, dermal absorption of PM2.5 posed a greater threat to the population, the incremental lifetime cancer risk (ILCR) of NMSP was 1.8 × 10-4. After considering bioavailability, BILCR decreased by 1-2 orders of magnitude in different regions, and dermal absorption decreased more than inhalation intake. Nevertheless, the dermal absorption of PM2.5 in NMSP still presents a probable carcinogenic risk. This study provides a necessary reference for the subsequent control of NMSP contamination.

Nano zerovalent Fe did not reduce metal(loid) leaching and ecotoxicity further than conventional Fe grit in contrasting smelter impacted soils: A 1-year field study.

The majority of the studies on nanoscale zero-valent iron (nZVI) are conducted at a laboratory-scale, while field-scale evidence is scarce. The objective of this study was to compare the metal(loid) immobilization efficiency of selected Fe-based materials under field conditions for a period of one year. Two contrasting metal(loid) (As, Cd, Pb, Zn) enriched soils from a smelter-contaminated area were amended with sulfidized nZVI (S-nZVI) solely or combined with thermally stabilized sewage sludge and compared to amendment with microscale iron grit. In the soil with higher pH (7.5) and organic matter content (TOC = 12.7 %), the application of amendments resulted in a moderate increase in pH and reduced As, Cd, Pb, and Zn leaching after 1-year, with S-nZVI and sludge combined being the most efficient, followed by iron grit and S-nZVI alone. However, the amendments had adverse impacts on microbial biomass quantity, S-nZVI being the least damaging. In the soil with a lower pH (6.0) and organic matter content (TOC = 2.3 %), the results were mixed; 0.01 M CaCl2 extraction data showed only S-nZVI with sludge as remaining effective in reducing extractable concentrations of metals; on the other hand, Cd and Zn concentrations were increased in the extracted soil pore water solutions, in contrast to the two conventional amendments. Despite that, S-nZVI with sludge enhanced the quantity of microbial biomass in this soil. Additional earthworm avoidance data indicated that they generally avoided soil treated with all Fe-based materials, but the presence of sludge impacted their preferences somewhat. In summary, no significant differences between S-nZVI and iron grit were observed for metal(loid) immobilization, though sludge significantly improved the performance of S-nZVI in terms of soil health indicators. Therefore, this study indicates that S-nZVI amendment of soils alone should be avoided, though further field evidence from a broader range of soils is now required.

Multi-process production occurs in the iron and steel industry, supporting 'dual carbon' target: An in-depth study of CO2 emissions from different processes.

Reducing CO2 emissions of the iron and steel industry, a typical heavy CO2-emitting sector, is the only way that must be passed to achieve the 'dual-carbon' goal, especially in China. In previous studies, however, it is still unknown what is the difference between blast furnace-basic oxygen furnace (BF-BOF), scrap-electric furnace (scrap-EF) and hydrogen metallurgy process. The quantitative research on the key factors affecting CO2 emissions is insufficient. There is also a lack of research on the prediction of CO2 emissions by adjusting industrial structure. Based on material flow analysis, this study establishes carbon flow diagrams of three processes, and then analyze the key factors affecting CO2 emissions. CO2 emissions of the iron and steel industry in the future is predicted by adjusting industrial structure. The results show that: (1) The CO2 emissions of BF-BOF, scrap-EF and hydrogen metallurgy process in a site are 1417.26, 542.93 and 1166.52 kg, respectively. (2) By increasing pellet ratio in blast furnace, scrap ratio in electric furnace, etc., can effectively reduce CO2 emissions. (3) Reducing the crude steel output is the most effective CO2 reduction measure. There is still 5.15 × 108-6.17 × 108 tons of CO2 that needs to be reduced by additional measures.

Multimethod analysis of large- and low-tapered single file reciprocating instruments: Design, metallurgy, mechanical performance, and irrigation flow.

AIM: To compare eight large- and low-tapered heat-treated reciprocating instruments regarding their design, metallurgy, mechanical properties, and irrigation flow through an in silico model. METHODOLOGY: A total of 472 new 25-mm E-Flex Rex (25/.04 and 25/.06), Excalibur (25/.05), Procodile (25/.06), Reciproc Blue R25 (25/.08v), WaveOne Gold Primary (25/.07v), and Univy Sense (25/.04 and 25/.06) instruments were evaluated regarding their design (stereomicroscopy, scanning electron microscopy, and 3D surface scanning), metallurgy (energy-dispersive X-ray spectroscopy and differential scanning calorimetry), and mechanical performance (cyclic fatigue, torsional resistance, cutting ability, bending and buckling resistance). Computational fluid dynamics assessment was also conducted to determine the irrigation flow pattern, apical pressure, and wall shear stress in simulated canal preparations. Kruskal-Wallis and one-way anova post hoc Tukey tests were used for statistical comparisons (α = 5%). RESULTS: Instruments presented variations in blade numbers, helical angles, and tip designs, with all featuring non-active tips, symmetrical blades, and equiatomic nickel-titanium ratios. Cross-sectional designs exhibited an S-shaped geometry, except for WaveOne Gold. Univy 25/.04 and Reciproc Blue displayed the smallest and largest core diameters at D3. Univy 25/.04 and E-Flex Rec 25/.04 demonstrated the longest time to fracture (p < .05). Reciproc Blue and Univy 25/.04 exhibited the highest and lowest torque to fracture, respectively (p < .05). Univy 25/.04 and Reciproc Blue had the highest rotation angles, whilst E-Flex Rec 25/.06 showed the lowest angle (p < .05). The better cutting ability was observed with E-Flex Rec 25/.06, Procodile, Excalibur, and Reciproc Blue (p > .05). Reciproc R25 and E-Flex Rec showed the highest buckling resistance values (p < .05), with WaveOne Gold being the least flexible instrument. The impact of instruments' size and taper on wall shear stress and apical pressure did not follow a distinct pattern, although Univy 25/.04 and E-Flex Rec 25/.06 yielded the highest and lowest values for both parameters, respectively. CONCLUSIONS: Low-tapered reciprocating instruments exhibit increased flexibility, higher time to fracture, and greater angles of rotation, coupled with reduced maximum bending loads and buckling strength compared to large-tapered instruments. Nevertheless, low-tapered systems also exhibit lower maximum torque to fracture and inferior cutting ability, contributing to a narrower apical canal enlargement that may compromise the penetration of irrigants in that region.

Arsenic pollution concerning surface water and sediment of Jie River: A pilot area where gold smelting enterprises are concentrated.

A comprehensive monitoring and risk assessment of arsenic (As) pollution concerning surface water and sediment is performed in the Jie River basin, where gold smelting enterprises are concentrated. The study area is divide into six regions, labeled as A, B, C, D, E, and F, from sewage outlets to downstream. Results shows that with far away from the sewage outlets, the total As concentrations in water and sediment gradually decrease from regions A to F. However, in region F, the concentration of bioavailable As significantly increases in the sediment due to the higher pH, leading to the transformation of As(V) into more mobile As(III). In sediment, Paracladius sp. exhibits strong resistance to As pollution in sediment, which can potentially elevate the risk of disease transmission. In water bodies, diatoms and euglena are the main phytoplankton in the Jie River while toxic cyanobacteria exhibits lower resistance to As pollution. Overall, measures should be taken to ecologically remediate the sediment in downstream while implementing appropriate isolation methods to prevent the spread of highly contaminated sediments from regions near sewage outlets.

Tribological behavior and in vitro biocompatibility of powder metallurgical Ti-15Mo/HA composite for bone repair.

Ti-15Mo/HA composite was prepared by powder metallurgy, and the influence of Hydroxyapatite (HA) on the microstructure, tribological behavior and in vitro biocompatibility was studied by comparison with TC4. The results show that the Ti-15Mo/HA composite consists of increased α-Ti, decreased ß-Ti and a variety of ceramic phases (CaTiO3, Ca3(PO4)2, CaO, etc.) with the increase of HA content. The friction coefficient and wear rate of Ti-15Mo/HA composite is apparently lower than those of TC4 due to solid solution strengthening of Mo in Ti and dispersion strengthening of ceramic phases. Ti-15Mo/5HA displays more excellent wear resistance than the other composite. TC4 alloy is dominated by adhesive wear, however, Ti-15Mo alloy is a combination of adhesive wear and abrasive wear. Ti-15Mo/HA composite is mainly subjected to abrasive wear, together with adhesive wear. The viability and the number of mouse osteoblasts in Ti-15Mo/5HA extract are higher than that of Ti-15Mo. The morphology of the osteoblasts is clear and full, and the growth and proliferation are satisfactory with the increased cell pseudopodia with the culture time. The Ti-15Mo/HA composite displays good wear resistance and biocompatibility, and accordingly has a potential application in bone repair materials.

Investigation of the enrichment-purification process and electrochemical performance of kish graphite in dust from blast furnace tapping yard.

Kish graphite is a typical byproduct of steel production, and its enrichment and purification are essential prerequisites for its high value and comprehensive utilization. To solve the problem of recovery and application of difficult-to-treat kish graphite with a small particle size obtained from metallurgical dust, kish graphite in blast furnace tapping yard dust was effectively enriched and purified by a comprehensive flotation-acid leaching treatment process in this study. The influence of the flotation agents on the flotation process was explored. The results showed that the optimized flotation agent dosage was 500.0 g·t-1 (collector) and 120.0 g·t-1 (frother), respectively. Based on the optimized flotation scheme, a graphite concentrate (FG) with 79.12 % carbon content and 93.5 % carbon recovery was obtained. After the leaching treatment with a HCl-HF mixed acid solution, the carbon content of the graphite concentrate increased to 95.55 %. The ID/IG value of the graphite concentrate was 0.145, and the average lattice spacing was approximately 0.3354 nm. The SEM results showed that the leaching-treated graphite concentrate (AFG) had a loose, fragment-like structure. When used as an anode material for lithium-ion batteries, The AFG still provided a high reversible capacity of âˆ¼370 mAh·g-1 and excellent coulombic efficiency of 99.6 % after 350 cycles. In addition, an industrial-grade recycling and utilization path for kish graphite based on a circular supply chain strategy was proposed. The results of this study may serve as a conceptual basis for the recovery and application of kish graphite from metallurgical dust.

A review of metallurgical slags as catalysts in advanced oxidation processes for removal of refractory organic pollutants in wastewater.

With the rapid growth of the metallurgical industry, there is a significant increase in the production of metallurgical slags. The waste slags pose significant challenges for their disposal because of complex compositions, low utilization rates, and environmental toxicity. One promising approach is to utilize metallurgical slags as catalysts for treatment of refractory organic pollutants in wastewater through advanced oxidation processes (AOPs), achieving the objective of "treating waste with waste". This work provides a literature review of the source, production, and chemical composition of metallurgical slags, including steel slag, copper slag, electrolytic manganese residue, and red mud. It emphasizes the modification methods of metallurgical slags as catalysts and the application in AOPs for degradation of refractory organic pollutants. The reaction conditions, catalytic performance, and degradation mechanisms of organic pollutants using metallurgical slags are summarized. Studies have proved the feasibility of using metallurgical slags as catalysts for removing various pollutants by AOPs. The catalytic performance was significantly influenced by slags-derived catalysts, catalyst modification, and process factors. Future research should focus on addressing the safety and stability of catalysts, developing green and efficient modification methods, enhancing degradation efficiency, and implementing large-scale treatment of real wastewater. This work offers insights into the resource utilization of metallurgical slags and pollutant degradation in wastewater.

Prediction of size-selective permitted daily exposures for mineral oil mist based on an in vitro study in different scenarios.

The incidence of DNA damage from exposure to specific types of metalworking fluids has been reported. In this research, size-selective permissible limits to prevent genotoxic damage in A549 cell lines exposed to two types of mineral oil were estimated for the first time using a benchmark dose approach and extrapolated to workers. The comet assay was performed based on Olive and Banath protocol to determine DNA damage. Then, the Benchmark Dose, the 95% lower bound confidence limit BMD, and the 95% upper-bound confidence limit BMD were determined using continuous response data. Finally, the four Benchmark Dose levels reported in the A549 cell line were extrapolated to the human population in occupational settings in two phases. This study showed when determining the permissible limits, the type used or unused, the type of injury, the organ affected in the body and the size of the particles should also be considered.

Relationship between exposure to metalworking fluids and nonalcoholic fatty liver disease.

OBJECTIVE: The relationship between metalworking fluids (MWFs) and nonalcoholic fatty liver disease (NAFLD) has not been previously explored. We aim to investigate the relationship between occupational exposure to MWFs and the prevalence of NAFLD and to determine the cumulative exposure threshold per day. METHODS: In 2020, 2079 employees were selected randomly from one computer numerical control machining factory in Wuxi for a questionnaire survey, and occupational health examinations were conducted at the affiliated branch of Wuxi Eighth People's Hospital. MWF samples were collected within the factory using the National Institute for Occupational Safety and Health (NIOSH) 5524 method. NAFLD was defined as having a hepatic steatosis index (HSI) ≥ 36 without significant alcohol consumption. The relationship between NAFLD and MWFs was analyzed using logistic regression, and the daily exposure threshold was calculated using R software. RESULTS: MWF exposure was found to be a risk factor for NAFLD in exposed workers compared to the non-exposed group. The OR for NAFLD in workers exposed to MWFs compared to controls was 1.42 (95% CI: 1.04-1.95). An increased risk of NAFLD was shown to be associated with an increasing dose. The daily exposure dose threshold to MWFs was found to be 6.54 mg/m3 (OR = 2.09, 95% CI: 1.24-3.52). CONCLUSION: An association between occupational exposure to MWFs and NAFLD was found. As the concentration of exposure rose, the prevalence of NAFLD was also escalated.