Antagonist enamel tooth wear produced by different dental ceramic systems: A systematic review and network meta-analysis of controlled clinical trials.

OBJECTIVES: The aim of this study was to evaluate the amount of enamel tooth wear induced by different antagonistic ceramic crown materials in the posterior area within a follow-up period up to 24 months in function. A network meta-analysis was performed to assess the effect of the materials on the mean vertical loss (MVL) of the antagonist enamel tooth surface. DATA: Main search terms used in combination: ceramic, dental materials, metal ceramic, tooth wear and dental enamel. SOURCES: An electronic search was conducted in PubMed/Medline, Embase, and Cochrane CENTRAL plus hand-searching. STUDY SELECTION: Eligibility criteria included clinical studies reporting on MVL on antagonist's tooth up to 24 months following the permanent crown placement. From a total of 5697 articles, 7 studies reporting on 261 crowns for 177 subjects with 3 ceramic materials (Lithium disilicate, metal-ceramic, monolithic zirconia) were included. Among all, metal-ceramic and zirconia caused significantly higher enamel tooth wear on antagonist teeth, representing 82.5 µm [54.4; 110.6]) and 40.1 µm [22.2; 58.0]) more MVL than natural teeth group. In contrast, lithium disilicate showed only 5.0 µm [-48.2; 58.1]) more MVL than occurs on opposing natural teeth. CONCLUSIONS: This systematic review demonstrated that prosthodontic ceramic materials produced significantly more antagonist enamel tooth wear than opposing natural enamel tooth wear, and ceramic material type was correlated to the degree of enamel tooth wear. Additional well-conducted, randomized controlled trials with homogeneous specimens are required due to inadequate sample size and number of the clinical studies included in the analyses. CLINICAL SIGNIFICANCE: The amount of wear caused by different restorative materials has a high influence on the antagonistic natural teeth and should therefore be evaluated intensively by the dentist.

Effect of Hydrothermal Aging and Beverages on Color Stability of Lithium Disilicate and Zirconia Based Ceramics.

Background and Objectives: All-ceramic prosthesis is widely used in modern dental practice because of its improved physico-mechanical and optical properties. These restorations are exposed to coloring agents from various nutrition and beverages in the oral cavity. Long-term color stability is critical for the success of these restorative materials. The purpose of this in vitro study was to assess the effect of common beverages and mouthwash on the color stability of lithium disilicate (LD), monolithic zirconia (MZ) and bilayer zirconia (BZ) surfaces. Materials and Method: Thirty disc-shaped specimens from each material were fabricated; each group was subdivided (n = 10) according to coffee, green tea and chlorhexidine immersion solutions. The baseline color of ceramic discs was recorded according to the CIE L*a*b* system with a portable spectrophotometer. The second measurement was recorded after 3000 thermocycling and immersion in coloring agents for 7 days. The mean color difference was calculated and data were compared with Kruskal-Wallis and Mann-Whitney post hoc tests (0.05). Results: ΔE values for LD with the immersion of coffee, tea, and Chlorhexidine gluconate (CHG) were 1.78, 2.241 and 1.58, respectively. Corresponding ΔE values for MZ were 5.60, 5.19, and 4.86; marginally higher than the clinically acceptable level of 3.5. Meanwhile, BZ showed better color stability compared to MZ with ΔE values of 4.22, 2.11 and 1.43. Conclusions: Among the ceramics evaluated, LD ceramic was found to be more color stable, while MZ ceramics displayed a higher susceptibility to discoloration. MZ and BZ ceramic colors were significantly altered with coffee immersion, while LD ceramics were more affected by green tea.

In vitro investigation of human enamel wear by dental porcelain.

BACKGROUND: Ceramic crown that fires the layering porcelain on zirconia corping is starting to be used due to aesthetic requirements. However, many ceramics are used, but wear characteristics are often unknown. OBJECTIVE: This study was performed to investigate the wear of human enamel by porcelains, and to determine the influence of porcelain hardness, surface roughness and crystal of porcelain on the enamel wear. METHODS: Enamel specimens were prepared from extracted human molar teeth. Porcelain specimens were prepared from Deguceram Gold, Vita Omega 900, and Cercon Ceram Kiss. Enamel wear volume was calculated and the porcelain wear depth, surface roughness and Vickers hardness was measured. Moreover, the observation of a crystal by scanning electron microscope and the crystal by X-ray diffraction were identified. RESULTS: Omega 900 showed the smallest enamel wear volume and porcelain wear depth. The Vickers hardnesses of Omega 900 and Cercon Ceram Kiss were almost identical. Leucite was detected from Deguceram Gold and Omega 900, and Silica and Silicon Nitride were detected from Cercon Ceram Kiss. CONCLUSIONS: The enamel wear is influenced not by the hardness of the porcelain but by the surface roughness, the size and shape of the crystal.

Effects of New Generation All-Ceramic and Provisional Materials on Fibroblast Cells.

PURPOSE: The purpose of this in vitro study was to evaluate the cytotoxic and apoptotic effects of seven new-generation all-ceramic materials for CAD/CAM (Lava Ultimate [LU], VITA Mark II [VM], InCoris TZI [IC], IPS e.max CAD [EM], VITA Suprinity [VS], Cerasmart [CS], IPS Empress CAD [EC]) and six provisional materials (Protemp 4 [PT], Telio CAD [TC], CAD-Temp [CT], Telio Lab [TL], Temdent Classic [TD], Telio CS C&B [TS]) on L929 mouse fibroblast cells. MATERIALS AND METHODS: 24 disc-shaped specimens (∅ = 5 mm, h = 2 mm) were prepared from each test material. Medium extracts were collected at the 1st, 3rd, and 7th days for each group and tested using the L929 cell line. Cytotoxicity was evaluated using XTT assay, and apoptosis was determined by Annexin-V/PI staining. Data were analyzed using one-way ANOVA, Tukey's multiple comparison tests at a significance level of p < 0.05. RESULTS: The cell viability results among all-ceramic material groups after the 1st and 7th days of incubation periods showed statistically significant differences (p < 0.05). There were significant differences within the ceramic groups in different incubation periods regarding apoptosis rate (p < 0.05). Throughout the entire test period, LU and VM from the CAD/CAM all-ceramic materials and PT and TC from the provisional restoration materials showed cell viability higher than 90%. EC and TD showed the lowest cell viability and highest apoptosis rates in their own groups. For the provisional materials, there were significant differences in cell viability and apoptosis rate in all the incubation periods for each material (p < 0.05). CONCLUSIONS: Although some new-generation CAD/CAM and provisional restoration materials display slight cytotoxicity values, the results are still within the reliable range, and they can safely be used in clinical conditions.

Investigation on the properties of borate bonding agents: Ti6Al4V-porcelain bonding, chemical durability and preliminary cytotoxicity.

The purpose of this study was to investigate the properties of the borate bonding agents (BBAS) including chemical durability, biocompatibility and bonding characteristics of porcelain to Ti6Al4V. The bond strength was performed by the three-point bending test. And the chemical durability and ion release of BBAS were tested by chemical soaking and inductively coupled plasma optical emission spectrometry (ICP-OES), respectively. Moreover, cytotoxicity was evaluated by cell viability assay and cell adhesion using human osteosarcoma cells (MG-63) and cell counter kit-8 (CCK-8) assay. To investigate the influences of composition and microstructure changes on all the properties mentioned above, the 11B and 27Al spectra and infrared spectra of BBAS were measured by solid-state nuclear magnetic resonance (SSNMR) and Fourier transform infrared spectroscopy (FTIR), respectively. Combined with all these properties of BBAS, the optimal addition proportion of Al2O3 into BBAS is 20 mol%. The relative contents of [BO3], [BO4], [AlO4], [AlO5] and [AlO6] have great influences on these properties of BBAS. BBAS, possessing excellent chemical durability, good biocompatibility and low ion release and being an effective way to improve the Ti6Al4V-porcelain bond strength, have significant clinical potentials in porcelain fused to metal restorations.

Corrosion potential in artificial saliva and possible genotoxic and cytotoxic damage in buccal epithelial cells of patients who underwent Ni-Cr based porcelain-fused-to-metal fixed dental prostheses.

Nickel-chromium(Ni-Cr) based alloys account for the majority of the porcelain-fused-to-metal fixed dental prostheses(PFM-FDPs) on account of their superior properties despite both nickel and chromium being known as human carcinogens. Understanding the genotoxicity and the cytotoxicity alongside the characteristics of corrosion behavior of the alloy is vital for understanding their biocompatibility. This study has evaluated whether the Ni-Cr based alloys corroded in artificial saliva by analyzing alloy decomposition at different pH levels and immersion durations(7, 14, 21, and 28 days) using inductively coupled plasma-optic emission spectrophotometry(ICP-OES). The principal aim of the study was to determine the possible genotoxicity and cytotoxicity using micronucleus(MN) and other nuclear anomaly frequencies [nuclear bud(NBUD), binucleated(BNC), condensed chromatin(CC), karyorrhectic(KhC), pyknotic(PC) and karyolytic(KC) cells] and various cytome parameters [basal cells(BC), differentiated cells(DF)] with the buccal epithelial cell(BEC) micronucleus cytome assay(BMCyt). This test was administered at 1 pre- and 3 post-treatment time points to 40 patients who underwent installation of PFM-FDPs made of Ni-Cr based alloy. Furthermore, at the final post-treatment time point, saliva cotinine levels were measured with salivary cotinine quantitative enzyme immunoassay(EIA) kit and information obtained by questionnaire prior to the first pre-treatment time point was confirmed. The highest greatest release of Ni and Cr ions were seen at pH 2.3. MN and micronucleated cell frequencies, and BNC cell frequencies were significantly elevated at post-treatment time points(p < 0.03). BC, CC, KhC, PC and KC cell frequencies however were not significantly different between pre-and post-treatment time points(p > 0.05). MN frequency was significantly lower in non-smokers than in current and former smokers(p < 0.001) at the pre-treatment time point. There was no significant correlation between the unit number of PFM-FDPs and MN frequencies. Our results revealed that Ni-Cr based alloys are prone to corrosion and that PFM-FDPs fabricated with Ni-Cr based alloys may induce genotoxic effects rather than cytotoxic effect.

Randomized clinical study of wear of enamel antagonists against polished monolithic zirconia crowns.

OBJECTIVES: To test the hypothesis that there is no difference in the in vivo maximum wear of enamel opposing monolithic zirconia crowns, enamel opposing porcelain fused to metal crowns and enamel opposing enamel. METHODS: Thirty patients needing single crowns were randomized to receive either a monolithic zirconia or metal-ceramic crown. Two non-restored opposing teeth in the same quadrants were identified to serve as enamel controls. After cementation, quadrants were scanned for baseline data. Polyvinylsiloxane impressions were obtained and poured in white stone. Patients were recalled at six-months and one-year for re-impression. Stone models were scanned using a tabletop laserscanner to determine maximum wear. Statistical analysis was performed using Mann-Whitney U to determine any significant differences between the wear of enamel against zirconia and metal-ceramic crowns. RESULTS: Sixteen zirconia and 14 metal-ceramic crowns were delivered. There were no statistical differences in mean wear of crown types (p=0.165); enamel antagonists (p=0.235) and enamel controls (p=0.843) after one year. CONCLUSION: Monolithic zirconia exhibited comparable wear of enamel compared with metal-ceramic crowns and control enamel after one year. SIGNIFICANCE: This study is clinically significant because the use of polished monolithic zirconia demonstrated comparable wear of opposing enamel to metal-ceramic and enamel antagonists.

Determinação da tensão de falha de lascamento da porcelana de cobertura em prótese livre de metal utilizando análise de imagem / Determination of the failure stress of the porcelain chipping cover in metal free prosthesis using image analysis

A introdução da zircônia na Odontologia deu-se pela necessidade de melhores propriedades mecânicas dos materiais cerâmicos, pois com a crescente demanda estética, os cerâmicos tornaram-se materiais de largo uso, devido às suas propriedades estéticas e mecânicas. Em busca dessas propriedades, vários estudos analisaram a taxa de sobrevivência de restaurações zircônia-porcelana, relatando como uma das causas de falha a fratura precoce da porcelana de cobertura e o aumento significativo nos relatos clínicos de lascamento da porcelana de recobrimento aplicada sobre "coping" de zircônia. Diante desse problema, o objetivo deste trabalho foi determinar a tensão de falha no lascamento a partir de casos de clínicos e experimentais pertinentes a esse fenômeno em próteses fixas livres de metal .Foram coletados dados de artigos dos últimos 15 anos, por meio das bases de dados Pubmed e Google Schoolar, sendo selecionados para essa revisão os que obtiveram melhor abordagem do assunto, dando ênfase às possíveis causas de falhas nas restaurações cerâmicas dos casos clínicos e os ensaios realizados, visando um melhor entendimento desse fenômeno, via análise quantitativa e qualitativa, para melhor utilização e aproveitamento desse material na Odontologia. Para determinação da tensão de falha, foi empregada a mecânica da fratura linear elástica e determinado o fator de correção da trinca com base nas dimensões da trinca.Com a presente pesquisa, nota-se que amplitude de tensão influencia no processo de fratura, embora não tenha apontado exatamente para a causa da fratura. No entanto, pode-se inferir que uma baixa taxa de sobrevivência está relacionada a um grande defeito que, por sua vez, necessitou de uma sobrecarga para conduzir o processo de lascamento. Portanto, melhorias no processo de fabricação podem otimizar as características do material e sua aplicação final para suportar as tensões, a fim de aumentar a taxa de sobrevivência(AU)

The introduction of zirconia in dentistry was due to the need for better mechanical properties of ceramic materials, because of an increasing aesthetic demand. Ceramics became widely used materials due to their aesthetic and mechanical properties. Aiming at these properties, several studies have analyzed the survival rate of zirconia-porcelain restorations, reporting as one of the causes of failure. Early porcelain fracture coverage and a significant increase in clinical reports of veneering porcelain applied over "coping "of zirconia. In view of this problem, the objective of this work was to determine the failure causes of chipping from clinical and experimental cases associated to this phenomenon in fixed metal free prostheses. Data from articles of the last 15 years were collected through the Pubmed and Google Schoolar databases. Those who obtained the best approach to the subject were selected for this analysis, emphasizing the possible causes of failures in the ceramic restorations of the clinical cases and the tests performed. Aiming for a better understanding of this phenomenon, via quantitative and qualitative analysis, to better use this material in dentistry. To determine the failure causes, linear elastic fracture mechanics were used and the crack correction factor was determined based on the crack dimensions. With the present research, it is noticed that stress amplitude influences in the fracture process, although it has not pointed exactly the cause of the fracture. However, it can be inferred that a low survival rate is related to a large defect, this in turn needed an overload to conduct the chipping process. Therefore, the manufacturing process can improve the characteristics of the material and its final application to withstand the stresses in order to increase the survival rat(AU)

Zirconia-based versus metal-based single crowns veneered with overpressing ceramic for restoration of posterior endodontically treated teeth: 5-year results of a randomized controlled clinical study.

OBJECTIVES: The aim of this 5-year randomized controlled trial was to compare the longevity and clinical behavior of single posterior crowns made with pressable ceramic on zirconia and on metal frameworks, and if failures occur, to delineate the contributing factors. METHODS: 72 patients, who needed the covering of at least a molar and/or premolar, were included in the study. All teeth were endodontically treated, with absence of periapical lesion or active periodontitis. Ninety single crowns were made with zirconia or metal framework and covered with pressable veneering ceramics. Two independent examiners assessed the survival of restorations at 6 months, 1-4 and 5 years after restoration placement including periapical radiographs, intraoral photographs, and USPHS modified criteria. The statistical analyses were performed with the Kaplan-Meier method. RESULTS: One core fracture occurred in Zircad/Zirpress crowns and one metal ceramic crown was lost for root fracture. Chipping fracture of the veneering ceramic was detected in 2 metal-ceramic crowns and in 3 zirconia-based crowns. The Estimate Cumulative Survival (ECS) and the Estimate Cumulative Success (ECSs) with standard deviation (SE) were respectively 97,73±2,19 and 92,64±4,14 for zirconia-based crowns whereas 97,44±2,39 and 91,11±4,27 for porcelain fused to metal crowns. CONCLUSIONS: The present randomized controlled trial shows that the survival of zirconia-based and metal-based single crowns is similar over a follow-up period of 5 years. No significant differences in esthetic, functional and biological outcomes were demonstrated between the two groups. The main failure mode was the chipping fracture of the veneering ceramic in both materials. Study number on ClinicalTrial.gov NCT02758457. CLINICAL SIGNIFICANCE: According to the results of this clinical study, zirconia-based rehabilitations with overpressing veneering technique represent a valid alternative to metal-based for posterior single crown restorations.

Enamel wear by antagonistic restorative materials under erosive conditions.

OBJECTIVES: This study aimed to analyse loss of enamel worn against composite, leucite glass ceramic or enamel antagonists under non-erosive and alternating or simultanuous erosive-attritive conditions. MATERIALS AND METHODS: Flat human enamel specimens were loaded (1 Hz, 300 g loading weight, each subgroup n = 12) with antagonists made from a hybrid-composite (Z250, 3 M Espe), a nano-composite (Filtek Supreme XTE, 3 M Espe), leucite glass ceramic (IPS Empress CAD LT, Ivoclar Vivadent) or enamel. Specimens were either submitted to mechanical loading in mineral solution (60 s) or to loading under alternating or simultaneous erosive conditions. For alternating erosion-attrition, specimens were eroded by citric acid (pH 2.6, 60 s) and then loaded with the respective antagonist for 60s. For simultaneous erosion-attrition, specimens were loaded with the respective antagonist while being immersed in citric acid (pH 2.6, 60 s). After each cycle, specimens were stored in water for 1 h. After 18 cycles, enamel loss was calculated profilometrically and statistically analysed by two-way ANOVA and Tukey's post-hoc tests (p < 0.05). RESULTS: Enamel loss (µm, mean ± standard deviation) was significantly highest for simultaneous erosion-attrition (ceramic 9.4 ± 1.1, hybrid-composite 8.3 ± 0.7, nano-composite 7.8 ± 1.2, enamel 7.4 ± 0.8) followed by alternating erosion-attrition (ceramic 3.5 ± 0.5, hybrid-composite 2.1 ± 0.8, nano-composite 1.0 ± 0.2, enamel 2.5 ± 0.7) and attrition in mineral solution (ceramic 0.5 ± 0.3, hybrid composite 0.3 ± 0.1, nano composite 0.1 ± 0.2, enamel 0.1 ± 0.1). Ceramic antagonists resulted in significantly higher loss than the remaining antagonistic materials when alternating or simultaneous erosion-attrition was performed. CONCLUSION: Erosive conditions had a massive impact on enamel worn against different antagonistic materials, with simultaneous erosive-attritive conditions being more detrimental than alternating erosive-attritive conditions. CLINICAL RELEVANCE: Enamel wear by antagonistic restorative materials is significantly influenced by erosive conditions.

Influence of misfit on the occurrence of veneering porcelain fractures (chipping) in implant-supported metal-ceramic fixed dental prostheses: an in vitro pilot trial.

OBJECTIVE: Technical complications such as veneer fractures are more common in implant-supported than tooth-supported restorations. The underlying causes have not been fully identified. The aim of this study was to evaluate whether misfit between the restoration and the implant may affect the risk of veneer fractures. MATERIALS AND METHODS: Twenty standardized five-unit implant-supported metal-ceramic fixed dental prostheses (FDP)s were manufactured and fixed in acrylic blocks. The test group consisted of ten FDPs fixed with a 150-µm misfit at the distal abutment. The remaining ten FDPs were fixed without misfit and acted as a control group. All FDPS underwent cyclic loading for a total of 100,000 cycles at 30-300 N. The FDPs were checked for cracks or chip-off fractures regularly. After cyclic load, the retorque value of all abutment screws was checked. RESULTS: Cracks within the veneering porcelain were noted in nine FDPs in the test group and one FDP in the control group. This difference was statistically significant (P < 0.001). Fractures of the veneering porcelain occurred in three FDPs in the test group. No fractures occurred in the control group. This difference was not statistically significant. There were no significant differences in retorque values neither between the groups nor between different abutment positions in the FDPs. CONCLUSIONS: Within the limitations of this in vitro pilot trial, it is suggested that misfit between a restoration and the supporting implant may increase the risk of cracking and/or chipping of the veneering porcelain for metal-ceramic FDPs.

Comparison of fracture strength and failure mode of different ceramic implant abutments.

STATEMENT OF PROBLEM: The whitish color of zirconia (ZrO2) abutments offers favorable esthetics compared with the grayish color of titanium (Ti) abutments. Nonetheless, ZrO2 has greater opacity, making it difficult to achieve natural tooth color. Therefore, lithium disilicate (LaT) abutments have been suggested to replace metal abutments. PURPOSE: The purpose of this in vitro study was to evaluate the fracture strength and failure mode of single-tooth implant restorations using ZrO2 and LaT abutments, and to compare them with titanium (Ti) abutments. MATERIAL AND METHODS: Five different types of abutments, Ti; ZrO2 with no metal base; ZrO2 with a metal base (ZrT); LaT; and LaT combination abutment and crown (LcT) were assembled on 40 Ti implants and restored with LaT crowns. Specimens were subjected to quasistatic loading using a universal testing machine, until the implant-abutment connection failed. As bending of the metal would be considered a clinical failure, the values of force (N) at which the plastic deformation of the metal occurred were calculated, and the rate of deformation was analyzed. Statistical analysis was done using the Mann-Whitney U test (α=.05). RESULTS: Group ZrO2 revealed the lowest resistance to failure with a mean of 202 ±33 N. Groups ZrT, LaT, and LaC withstood higher forces without fracture or debonding of the ceramic suprastructure, and failure was due to deformation of metal bases, with no statistically significant differences between these groups regarding the bending behavior. CONCLUSIONS: Within the limitations of this in vitro study, it was concluded that LaT abutments have the potential to withstand the physiological occlusal forces that occur in the anterior region and that ZrO2 abutments combined with Ti inserts have much higher fracture strength than pure ZrO2 abutments.

Findings of a Four-Year Randomized Controlled Clinical Trial Comparing Two-Piece and One-Piece Zirconia Abutments Supporting Single Prosthetic Restorations in Maxillary Anterior Region.

The purpose of this randomized controlled study is to investigate the clinical results obtained over four years and incidence of complications associated with one- versus two-piece custom made zirconia anchorages, in single tooth implant-supported restorations of the maxillary anterior region. Sixty-five patients, with a total of 74 missing maxillary teeth, were selected in the period from February 2007 to July 2010. Two different ways of custom made zirconia abutment and final prosthetic restoration were evaluated: a standard zirconia abutment associated with a pressed layer of lithium disilicate with an all-ceramic cemented restoration versus one-piece restoration with the facing porcelain fired and pressed straight to the custom made zirconia abutment. In 29 cases, the restoration consisted of an all-ceramic restoration for cementation (two pieces); in 45 cases the restoration was a screw-retained restoration (one piece). Three all-ceramic restorations broke during the observation time. Two one-piece restorations fractured after 26 months. At follow-up examination there were no significant differences between one-piece and two-piece groups regarding the PI, BI, and MBL. Awaiting studies with longer follow-up times, a careful conclusion is that zirconia anchorages for single-implant restorations seem to demonstrate good short-term technical and biological results.

A practice-based clinical evaluation of the survival and success of metal-ceramic and zirconia molar crowns: 5-year results.

This practice-based study evaluates the survival and success of conventionally luted metal-ceramic and zirconia molar crowns fabricated by using a prolonged cooling period for the veneering porcelain. Fifty-three patients were treated from 07/2008 to 07/2009 with either metal-ceramic crowns (MCC) or zirconia crowns (ZC). Forty-five patients (26 female) with 91 restorations (obser-vational period: 64.0 ± 4.8 months) participated in a clinical follow-up examination and were included in the study. Estimated cumulative survival (ECSv), success (ECSc) and veneering ceramic success (ECVCSc) were calculated (Kaplan-Meier) and analysed by the crown fabrication technique and the position of the restoration (Cox regression model) (P < 0.05). Five complete failures (MCC: 2, ZC: 3) were recorded (5-year ECSv: MCC: 97.6%, (95% confidence interval (95%-CI): [93%; 100%]/ZC: 94.0%, (95%-CI): [87%; 100%]). Of the MCCs (n = 41), 85.0%, [95%-CI: (77%; 96%)] remained event-free, whereas the ECSc for the ZCs (n = 50) was 74.3% (95%-CI): [61%; 87%]. No significant differences in ECSv (P = 0.51), ECSc (P = 0.43) and ECVCSc (P = 0.36) were detected between the two fabrication techniques. Restorations placed on terminal abutments (n = 44) demonstrated a significantly lower ECVCSc (P = 0.035), (5-year VCF-rate: 14.8%) than crowns placed on tooth-neighboured abutments (n = 47), (5-year VCF-rate: 4.3%). In the present study, zirconia molar crowns demonstrated a 5-year ECSv, ECSc and ECVCSc comparable to MCCs. Irrespective of the fabrication technique, crowns on terminal abutments bear a significantly increased risk for VCFs. Clinical investigations with an increased number of restorations are needed.

Interaction of titanium, zirconia and lithium disilicate with peri-implant soft tissue: study protocol for a randomized controlled trial.

BACKGROUND: Against the background of increasing use of dental implants, and thus an increasing prevalence of implant-associated complications, a deeper understanding of the biomolecular mechanisms in the peri-implant tissue is needed. Peri-implant soft tissue is in direct contact with transmucosal dental implant abutments. The aim of this trial is to distinguish the biomolecular and histological interactions of various dental abutment materials with peri-implant soft tissue. METHODS/DESIGN: The study is designed as a prospective, randomized, investigator-initiated clinical pilot trial with blinded assessment. We will ultimately include 24 eligible patients who opt for implant treatment to replace a single missing posterior tooth. Three months after implantation (submerged procedure), the study begins with the second-stage surgery. Each of the 24 patients will be given three different transmucosal abutments (zirconia, lithium disilicate, titanium) consecutively. The sequence in which the three materials are used is randomized. Peri-implant crevicular fluid is sampled weekly around the respective abutment for biomolecular analyses. After one month of wearing time, the stamping press from the second-stage surgery is used to gain a narrow gingival ring biopsy around the abutment for immunohistochemical analyses. The next abutment is then inserted. The same procedure is used for all three abutments. After sampling is completed, the patients will receive a definitive crown. The primary outcome measure of the trial is biomolecular detection of specific markers in the peri-implant crevicular fluid: matrix metalloproteinase 8, interleukin- 1ß, polymorphonuclear elastase, and myeloid-related protein MRP8/14 (calprotectin). Secondary outcome measures include immunohistochemical analyses and clinical parameters. DISCUSSION: The study design will allow us to perform correlation analyses between the clinical indices with biomarkers' expression in the interface of the transmucosal abutments and the peri-implant soft tissue. A deeper understanding of the three abutment materials' interactions with peri-implant soft tissue will help us understand the formation mechanisms of implant-associated complications and then develop prevention strategies. TRIAL REGISTRATION: The trial is registered at the German Clinical Trial Register and the International Clinical Trials Registry Platform by the WHO under DRKS00006555 (Registered on 27 October 2014).

Clinical study to evaluate the wear of natural enamel antagonist to zirconia and metal ceramic crowns.

STATEMENT OF PROBLEM: Tooth wear is a complex process, which, if not prevented, may adversely affect the integrity of the stomatognathic system. Different restorative dental materials may affect the amount of wear on natural enamel antagonists. PURPOSE: The purpose of this in vivo study was to evaluate and compare the wear of enamel opposing natural enamel, zirconia, and metal ceramic crowns after 1 year. MATERIAL AND METHODS: Ten participants between 18 and 35 years of age requiring 2 complete crowns, 1 on either side of maxillary or mandibular molar region, and having healthy natural teeth in the opposing arch were selected. For each participant, 1 monolithic polished zirconia crown and 1 glazed metal ceramic crown were fabricated and cemented. To evaluate the wear of the antagonistic natural enamel (premolar and molar), polyvinyl siloxane impressions were made immediately (baseline) and at 1 year after cementation. The wear of natural enamel against natural enamel was evaluated as the control. The resulting casts were scanned (using a 3D white light scanner), and 3D software was used to calculate the maximum amount of linear wear. RESULTS: One-way repeated measures ANOVA was conducted to analyze data. Mean ±SD occlusal wear of the antagonistic enamel 1 year after the cementation of metal ceramic crowns was 69.20 ±4.10 µm for premolar teeth and 179.70 ±8.09 µm for molar teeth, whereas for zirconia crowns, it was 42.10 ±4.30 µm for premolar teeth and 127.00 ±5.03 µm for molar teeth. Occlusal wear of natural enamel opposing natural enamel was 17.30 ±1.88 µm in the premolar region and 35.10 ±2.60 µm in the molar region. The Bonferroni post hoc test revealed that the occlusal wear of antagonistic enamel 1 year after the cementation of a metal ceramic crown was significantly higher (P<.001) than that of an opposing zirconia crown or natural enamel. CONCLUSIONS: Zirconia crowns led to less wear of antagonist enamel than metal ceramic crowns, but more than natural enamel.

Enamel wear opposing polished and aged zirconia.

Aging of dental zirconia roughens its surface through low temperature degradation. We hypothesized that age-related roughening of zirconia crowns may cause detrimental wear to the enamel of an opposing tooth. To test our hypothesis, we subjected artificially aged zirconia and reference specimens to simulated mastication in a wear device and measured the wear of an opposing enamel cusp. Additionally, the roughness of the pretest surfaces was measured. The zirconia specimens, artificially aged by autoclave, showed no significant increase in roughness compared to the nonaged specimens. Furthermore, no significant difference in material or opposing enamel wear between the aged and nonaged zirconia was seen. All zirconia specimens showed less material and opposing enamel wear than the enamel to enamel control or veneering porcelain specimens. Scanning electron micrographs showed relatively smooth surfaces of aged and nonaged zirconia following wear testing. The micrographs of the veneering ceramic showed sharp fractured edges and fragments of wear debris. Zirconia may be considered a wear-friendly material for restorations opposing enamel, even after simulated aging.

Marginal bone loss of two implant systems with three different superstructure materials: a randomised clinical trial.

Marginal bone level is a criterion for implant success. The aetiological factors of bone loss have not been clarified. The aim of this study was to evaluate the influence of implant systems and prosthetic materials on the marginal bone loss. Twenty-three patients participated; two implant systems and three superstructure materials were used in this study. Twenty-two of the implants were restored with porcelain fused to base metal alloy (BMA), 25 with porcelain fused to noble metal alloy (NMA) and 20 with zirconium oxide-based ceramics. Radiographs were taken at baseline and 3, 6 and 12 months after loading. Crestal bone-level changes were assessed with digital subtraction radiographs. The effects of superstructure materials and implants were evaluated with one-way anova and independent samples t-test, respectively (α = 0·05). The mean crestal bone loss was found 0·483 mm in 3 months, 0·622 mm in 6 months and 0·816 mm in 12 months. Prosthetic materials were found to have greater effect (ß = 0·575, P = 0·015) on crestal bone loss than implant systems (P > 0·05). The porcelain fused to BMA restorations showed higher crestal bone loss than NMA-based restorations (P = 0·003) at 3 months, (P = 0·038), at 6 months and (P = 0·00) at 12 months; however, crestal bone loss differences between NMA and zirconia were not significant (P = 0·629) at 3 months, (P = 0·974) at 6 months and (P = 1) at 12 months. Within the limitations of this study, our results revealed that rather than the implant systems, prosthetic materials seemed to have an effective role on crestal bone.

Practice-based clinical evaluation of metal-ceramic and zirconia molar crowns: 3-year results.

This practice-based study evaluates the clinical performance of conventionally luted metal-ceramic and zirconia molar crowns fabricated with pronounced anatomical core design and a prolonged cooling period of the veneering porcelain. Fifty-three patients were treated from 07/2008 until 07/2009 with either metal-ceramic crowns (MCC) (high-noble alloy + low-fusing porcelain) or zirconia crowns (Cercon System, DeguDent, Germany). Forty-nine patients (30 women/19 men) with 100 restorations (metal-ceramic: 48/zirconia: 52, mean observational period: 36·5 ± 6 months) participated in a clinical follow-up examination and were included in the study. Time-dependent survival (in situ criteria), success (event-free restorations) and chipping rates (defects of the veneering ceramics) were calculated according to the Kaplan-Meier method and analysed in relation to the crown fabrication technique, using a Cox regression model (P < 0·05). Three complete failures (metal-ceramic: 1, zirconia: 2) were recorded (survival rate after 3 years: metal-ceramic: 97·6%, zirconia: 95·2%). Of the metal-ceramic restorations, 90·9% remained event-free (two ceramic fractures, one endodontic treatment), whereas the success rate for the zirconia was 86·8% (two ceramic fractures, one endodontic treatment, one secondary caries). No significant differences in survival (P = 0·53), success (P = 0·49) and ceramic fracture rates (P = 0·57) were detected. The combination of a pronounced anatomical core design and a modified firing of the veneering porcelain for the fabrication of zirconia molar crowns resulted in a 3-year survival, success and chipping rate comparable to MCC.