Evaluation of marginal and internal adaptation of veneers generated by the guided prosthetic tooth preparation system.

OBJECTIVE: This in vitro study aimed to assess and contrast the marginal and internal adaptation of all-ceramic prefabricated veneers manufactured via the FirstFit guided tooth preparation system against all-ceramic veneers produced using the chairside Computer-Aided Design/Computer Aided Manufacture (CAD/CAM) system following identical guided preparation protocols. MATERIALS AND METHODS: Two main groups were included, with 16 lithium disilicate veneers per group. Four typodonts were used for the test (FirstFit) and control CAD/CAM groups. Intraoral scans created master casts and preparation guides. Guides performed preparations on typodont teeth (two central incisors and two lateral incisors). Prepared teeth were scanned (CEREC Omnicam) to design and mill CAD/CAM veneers. Marginal gap thickness and cement space thickness were measured using light microscopy at four locations: marginal, cervical internal, middle internal, and incisal internal. RESULTS: No significant difference existed between groups for marginal adaptation (p = 0.058) or incisal internal adaptation (p = 0.076). The control group had significantly lower values for middle internal adaptation (p = 0.023) and cervical internal adaptation (p = 0.019). CONCLUSIONS: Guided preparation evaluation showed no significant differences in marginal or incisal internal adaptation. The CAD/CAM group had significantly lower middle and cervical internal adaptation values.

Effect of a modified laminate veneer preparation design on absolute margin discrepancy and marginal overhang.

STATEMENT OF PROBLEM: Veneer preparation designs impact veneer accuracy. However, whether a modified design could reduce absolute margin discrepancy and marginal overhangs is unclear. PURPOSE: The purpose of this in vitro study was to investigate whether a modified veneer preparation design enhances the absolute margin discrepancy and marginal overhang. MATERIAL AND METHODS: The absolute margin discrepancy and the marginal overhang of 3 different veneer preparation designs on a typodont tooth (n=20): feather edge, shoulder, and shoulder with wings were measured. The feather edge design was prepared first and subsequently modified to create the shoulder and shoulder with wings preparations. Ceramic veneers were fabricated using computer-aided design and computer-aided manufacture with each veneer assessed for fit before cementation. Ten specimens were cut vertically, and 10 were cut horizontally in each group. The absolute margin discrepancy and marginal overhangs were measured for each cross-section with scanning electron microscopy. Descriptive data analysis and hypothesis testing were conducted using the nonparametric Kruskal Wallis test (α=.05). RESULTS: On the vertical sections, the shoulder with wings preparation had the best absolute margin discrepancy and overhang. The design was also best for mesial overhang and mesial absolute margin discrepancy when measuring horizontally. CONCLUSIONS: The shoulder with wings preparation design produced the smallest cervical absolute margin discrepancy and overhang. This design also produced absolute margin discrepancy and overhangs comparable with those of the shoulder design in the proximal areas.

Computer-aided design software-enabled preclinical prosthodontic training: A digital education technique.

The prosthodontics preclinical training modules involve textbook-based two-dimensional (2D) ideal images and practicing on manikin models to emulate ideal tooth preparations and teeth arrangements. Relying solely on 2D images as objectives for preclinical exercises limits the trainee's creative skills to instructions of textbooks and clinical instructions received. With advancements in digital dentistry, dental trainees should have early exposure to the three-dimensional (3D) rendering of ideal preclinical objectives. A dental education technique using computer-aided design software and smartphones is described that will allow 3D rendering of ideal prosthodontic training assignments allowing early exposure to digital dentistry for dental training students.

Influence of the Operator`s Experience, Working Time, and Working Position on the Quality of the Margin Width: In Vitro Study.

Background and Objectives: Appropriate tooth preparation is mandatory to obtain a perfect marginal fit of fixed restorations. The heavy chamfer is the most commonly used finish line, especially for minimally invasive tooth preparation. The aim of the study was to compare the width of the finish line obtained during tooth preparation performed by experienced (university lecturers) and inexperienced persons (dental students) in different working times and positions. Materials and Methods: Forty left upper-second molars were prepared on the simulator by each participant, totalizing 160 prepared teeth. A new round-end tapered diamond was used to obtain the 0.5 mm width of the heavy chamfer. The prepared teeth were photographed using a Canon D5300 camera with a macro lens attached to a tripod. The measurements were made with the Image-Pro Insight software selecting the same eight reference points. From these points, perpendicular lines were drawn above the finish line to the axial walls and the distance between the chamfer's outer edge and the axial wall's inner edge was measured. GraphPad Instat and NCSS Dowson Edition software were used. The statistical significance was set at p < 0.05. The mean (M) and standard deviation (SD) were calculated. The used tests: one sample t-test, ANOVA test, and Tukey-Kramer Multiple Comparisons Test. Results: Statistically significant differences were obtained according to the experience of the participant, preparation time, patient's position, and the chamfer width on the prepared tooth different surfaces. Conclusions: Daytime or weeklong tiredness and patient position do not affect the width of the heavy chamfer prepared by experienced and inexperienced persons. The experience and the operator's working position influence the width of the prepared finish line.

Effect of cement gap and drill offset on the marginal and internal fit discrepancies of crowns designed with different tooth preparations.

AIM: The aim of the present study was to evaluate the effect of cement gap and drill offset on the marginal and internal fit discrepancies of crowns designed with different tooth preparations. MATERIALS AND METHODS: Five tooth preparations were constructed, and crowns with different cement gaps and drill offsets were obtained. Then, best-fit alignment was performed on the crowns with the corresponding tooth preparations, and the fit discrepancies were expressed by color-coded difference images and root mean square (RMS) values. The RMS values of each group were analyzed by the rank-based Scheirer-Ray-Hare test (α = 0.05). RESULTS: The color segments in the sharp line angles area of the Sharp line angles group changed significantly before and after the drill offset. The cement gap had a significant effect on the marginal, internal, or overall fit discrepancies of the five design groups (P < 0.001), while the drill offset had a significant effect on the marginal fit discrepancies of the Shoulder-lip group and the internal or overall fit discrepancies of the Sharp line angles group (P < 0.001). Additionally, the interaction effect between cement gap and drill offset was significant for the marginal fit discrepancies of the Shoulder-lip group and the internal or overall fit discrepancies of the Sharp line angles group (P < 0.01). CONCLUSIONS: The cement gap and drill offset had a significant adverse effect on the marginal or internal fit discrepancies of the crowns designed with the shoulder-lip and sharp line angles designs. Tooth preparation designs with intense curvature changes such as shoulder-lip and sharp line angles should be avoided clinically.

Impact of marginal defects on the accuracy of automated finish line detection in tooth preparation.

AIM: The present study aimed to evaluate the accuracy of automated detection of preparation finish lines in teeth with defective margins. MATERIALS AND METHODS: An extracted first molar was prepared for a full veneer crown, and marginal defects were created and scanned (discontinuity of finish line: 0.5, 1.0, and 1.5 mm; additional line angle: connected, partially connected, and disconnected). Six virtual defect models were entered into CAD software and the preparation finish line was designated by 20 clinicians (CAD-experienced group: n = 10; CAD-inexperienced group: n = 10) using the automated finish line detection method. The accuracy of automatic detection was evaluated by calculating the 3D deviation of the registered finish line. The Kruskal-Wallis and Mann-Whitney U tests were used for between-group comparisons (α = 0.05). RESULTS: The deviation values of the registered finish lines were significantly different according to conditions with different amounts of finish line discontinuity (P < 0.001). There was no statistical difference in the deviation of the registered finish line between models with additional line angles around the margin. Moreover, no statistical difference was found in the results between CAD-experienced and CAD-inexperienced operators. CONCLUSIONS: The accuracy of automated finish line detection for tooth preparation can differ when the finish line is discontinuous. The presence of an additional line angle around the preparation margin and prior experience in dental CAD software do not affect the accuracy of automated finish line detection.

[Prediction, analysis and application of learning curve of tooth preparation for all ceramic crowns of maxillary central incisors].

OBJECTIVE: To predict the learning curve of tooth preparation for all ceramic crowns of maxillary central incisors on phantom head simulators for graduate students participating in standardized dental resident training based on the modified Wright learning curve model, then to analyze and applicate the learning curve. METHODS: Twelve graduate students participating in standardized dental resident training were selected to prepare the resin maxillary central incisors on phantom head simulators for all ceramic crowns 4 times. The results of preparation were evaluated by 3 prosthetic experts with at least 10 years' experience focusing on the reduction, contour, taper, shoulder, finish line, margin placement, adjacent tooth injury, and preparation time for tooth preparation. The learning rate of tooth preparation was calculated by scores of tooth preparation of 4 times. The learning curve of tooth preparation was predicted based on the modified Wright learning curve model. According to the criteria of standardized training skill examinations for dental residents in Beijing, 80 was taken as the qualified standard score. The minimum training times for tooth preparation to satisfy the qualified standard score (80) was calculated, to analyze the characteristics of learning curve and evaluate the effectiveness of tooth preparation. RESULTS: The scores of 4 tooth preparation were 64.03±7.80, 71.40±6.13, 74.33±5.96, and 75.98±4.52, respectively. The learning rate was (106±4)%, which showed the learning curve an upward trend. There were no significant differences between the qualified standard score and the predicted scores of tooth preparation from the 5th preparation to the 13th preparation (P > 0.05). The predicted score of the 14th preparation was higher than the qualified standard score (P < 0.05). CONCLUSION: The trend of the learning curve of tooth preparation for all ceramic crowns of maxillary central incisors on phantom head simulators for graduate students participating in standardized dental resident training is upward, which predicts the minimum training times higher than the qualified standard score is 14 times.

A pilot study on the use of a novel digital real-time evaluation system in undergraduate preclinical training of tooth preparation in fixed prosthodontics.

INTRODUCTION: In the light of the digital teaching, it is necessary that the effectiveness of a new digital real-time evaluation system in the preclinical training of tooth preparation be evaluated. MATERIALS AND METHODS: Forty undergraduate dental students of the fourth year were randomly divided into the control group and the experimental group to complete the training task of tooth preparation for porcelain fused to metal (PFM) crown restoring the upper right central incisor. The control students received conventional training with instructor's guidance. The experimental students received training with the digital system without instructor's guidance. Every student exercised preparation in two resin incisors in 3 h training by respective training methods. A third incisor was prepared on a dental model in the simulated head phantom by each student as the test on the next day. All students' tooth preparations were scored by the same two experienced experts. The experimental students were asked to answer a questionnaire regarding their attitudes and opinions on the digital evaluation system in preclinical training. RESULTS: There was no significant difference between the scores of the experimental group and the control group (p > .05). The students of two groups obtained the similar scores in the test (p > .05). Most of the students were supportive of the application of digital training system in the preclinical tooth preparation training course. CONCLUSIONS: The digital real-time evaluation system could provide effective training effects for the dental undergraduate students in the preclinical training of tooth preparation in fixed prosthodontics.

Evaluation of the Quality of Undergraduate Full Veneer Crown Preparations at a UK Dental Teaching Hospital.

OBJECTIVES: To determine the quality of full veneer crown preparations produced by supervised undergraduate students at a UK dental teaching hospital. METHODS: One hundred and eighty-five scanned digital dies between October 2019 and March 2021 were obtained. Using cross-sections in four planes, the total angle of convergence, abutment height, margin design and margin depth were evaluated. Statistical comparisons were made by plane, location, material-type, tooth-type, and inter- and intra-arch positions. RESULTS: Across all preparations the mean total angle of convergence was 24.8° ± 11.7°. and mean abutment height was 3.6 mm ± 1.0 mm. Mandibular and molar teeth were significantly more tapered (P ⟨0.001) and exhibited significantly shorter abutment heights (P ⟨0.001). Chamfer margins were the most frequently observed and mean margin depths ranged from 0.49-1.06 mm. The compliance to recommended taught parameters were 28.1%, 42.7%, 34.1% and 6.5% for total angle of convergence, abutment height, margin design and margin depth, respectively. CONCLUSIONS: The findings from this study suggest that compliance to taught parameters is poor, especially for molar teeth, and demonstrates the use of digital software in guiding future research and teaching.

Reliability of automatic finish line detection for tooth preparation in dental computer-aided software.

PURPOSE: This study aimed to investigate the accuracy of automatic tooth finish line registration compared to manual registration with regard to various finish line configurations and dental computer-aided design (CAD) software. METHODS: Finish line registrations were performed on 15 digital tooth models with different finish line configurations (edge roundness radius = 0 mm, 0.2 mm, and 0.4 mm; edge angle = 30°, 60°, 90°, 120°, and 150°) using automatic and manual methods for designing virtual copings (N = 150). The discrepancies between the registered finish line extracted from the copings and the actual finish line segmented from the digitized tooth model were measured. Three-way analysis of variance (ANOVA) and post-hoc analyses with Bonferroni correction (α = 0.05) were used to analyze the results. RESULTS: The finish line configurations, registration methods, and CAD software interacted with the accuracy of the registered finish line (p = 0.001). The automatic finish line registration method exhibited larger error values than the manual method, especially at high finish line edge roundness and obtuse edge angles for both EXOCAD and R2CAD software (p < 0.001). The difference in dental CAD software affected the registration accuracy in the automatic method (p < 0.001), but not in the manual method (p = 0.676). CONCLUSIONS: Finish line registration errors may occur when the automatic registration method is applied to the indistinct edge of tooth preparation. The accuracy of the automatic finish line registration could differ according to the CAD software program.

Prediction, analysis and application of learning curve of tooth preparation for all ceramic crowns of maxillary central incisors / 北京大学学报(医学版)

OBJECTIVE@#To predict the learning curve of tooth preparation for all ceramic crowns of maxillary central incisors on phantom head simulators for graduate students participating in standardized dental resident training based on the modified Wright learning curve model, then to analyze and applicate the learning curve.@*METHODS@#Twelve graduate students participating in standardized dental resident training were selected to prepare the resin maxillary central incisors on phantom head simulators for all ceramic crowns 4 times. The results of preparation were evaluated by 3 prosthetic experts with at least 10 years' experience focusing on the reduction, contour, taper, shoulder, finish line, margin placement, adjacent tooth injury, and preparation time for tooth preparation. The learning rate of tooth preparation was calculated by scores of tooth preparation of 4 times. The learning curve of tooth preparation was predicted based on the modified Wright learning curve model. According to the criteria of standardized training skill examinations for dental residents in Beijing, 80 was taken as the qualified standard score. The minimum training times for tooth preparation to satisfy the qualified standard score (80) was calculated, to analyze the characteristics of learning curve and evaluate the effectiveness of tooth preparation.@*RESULTS@#The scores of 4 tooth preparation were 64.03±7.80, 71.40±6.13, 74.33±5.96, and 75.98±4.52, respectively. The learning rate was (106±4)%, which showed the learning curve an upward trend. There were no significant differences between the qualified standard score and the predicted scores of tooth preparation from the 5th preparation to the 13th preparation (P > 0.05). The predicted score of the 14th preparation was higher than the qualified standard score (P < 0.05).@*CONCLUSION@#The trend of the learning curve of tooth preparation for all ceramic crowns of maxillary central incisors on phantom head simulators for graduate students participating in standardized dental resident training is upward, which predicts the minimum training times higher than the qualified standard score is 14 times.

An Evaluation of the Usefulness of YouTube® Videos on Crown Preparation.

BACKGROUND: You Tube is one of the most commonly used online sources for sharing information and knowledge. Academic topics or clinical data shared on this platform is not peer reviewed or evaluated by subject specialists for accuracy. No study was found in the literature examining the validity of crown preparation videos available at this platform. OBJECTIVE: To evaluate the authenticity of the content and quality of the crown preparation videos uploaded on the YouTube. METHODS: The systematic search for YouTube videos was carried out over a period of one year from January 2020 until February 2021. The keywords or phrases and tags used were crown preparation, PFM crown preparation, all ceramic crown preparation, and dental crown preparation. The videos were shortlisted on the basis of inclusion and exclusion criteria to select educationally useful videos in terms of content and quality. RESULTS: Three subject specialists evaluated the videos on crown preparation three times to shortlist only 12 (11%) educationally useful videos out of 109 relevant videos. These 12 videos met the preset inclusion criteria. CONCLUSION: Although YouTube is the most popular social media platform used as the source of information by the students, the majority of uploaded content lacks authenticity. This study found that crown preparation videos uploaded by the faculty members or subject specialists can be considered as the reliable source.

Success of Feather Margin Preparation for Full Metal Prosthodontic Crowns in the Canine Teeth in 84 Pet and Working Dogs (2005-2017).

Medical and dental records of Veterinary Dental Specialties and Oral Surgery were searched to identify dogs that received full metal prosthodontic crowns on canine teeth, using a feather or knife edge preparation between 2005 and 2017. A total of 160 teeth in 84 dogs were included in the study. Current follow-up by telephone, electronic mail, or electronic messaging was conducted, in addition to thorough record review for in-person recheck examinations. Treatment was considered successful if the prosthodontic crown was in place and no further or additional injury to the tooth had occurred at the time of reexamination, owner contact, or patient death. Tooth fracture apical to the prosthodontic crown occurred in 2 (1.25%) cases, bond failure between the tooth and the cement or the cement and the crown occurred in a single case (0.625%), and one metal crown required replacement after 3 years due to wear (0.625%), for an overall failure rate of 2.5%. These results suggest that feather preparation of the margin is at least as, if not more, successful as the more commonly accepted and performed chamfer margin, and thus is a successful, practical and durable option for prosthodontic crown treatment in dog canine teeth.

A Digital Chairside Technique for an Accurate Evaluation of the Taper of the Prepared Teeth for the Restoration of Crowns and Fixed Partial Dentures.

AIM: The aim of the article was to provide a digital chairside method for the objective evaluation of the taper of prepared abutment teeth retaining a fixed partial denture (FPD). BACKGROUND: According to research, the taper of the abutment teeth supporting an FPD has a direct effect on both retention and stress transmission to the abutment teeth. However, no approaches have been documented in the literature that objectively quantify the taper of the prepared teeth chairside, in a simple and cost-effective manner. TECHNIQUE: The proposed technique utilized an intraoral camera with an on-the-go (OTG) connection, and a silicone dental bite block. The images of the prepared teeth were captured using this camera from the facial aspect. An indigenous program was developed using the MATLAB (Matrix Laboratory 2013) software for the analysis of the images and the taper of each abutment tooth was calculated in degrees using the software. CONCLUSION: The novel, chairside, digital technique utilizes an intraoral camera and a computer-generated software package to quantify and evaluate the taper of abutment teeth efficiently. This, in turn, can help minimize the errors in the treatment of FPD and improve the retention of the prosthesis. CLINICAL SIGNIFICANCE: The current technique enables the clinician to avoid over-preparation of the abutment teeth by assessing its taper chairside. This digital technique can be a beneficial alternative to the existing procedures for an accurate assessment of taper, especially for the inexperienced operator. Hence, the quality of retention, and thereby the long-term success of the crowns and FPDs, can be enhanced. This article was presented as a postgraduate paper titled "Scan and Plan" on March 6, 2020, at 22nd IPS (Indian Prosthodontic Society) PG Convention, Kochi, India.

Dentists' Perception and Clinical Use of Preformed Metal Crowns to Restore Primary Molar Defects in Chengdu City, China: A Cross-Sectional Study.

BACKGROUND: Preformed metal crowns (PMCs), as an effective technique recommended for the enduring restoration of primary molar defects, have not been widely implemented in China as well as that in Western countries. This study is aimed at assessing the knowledge on the clinical use of the PMC technique and its effective factors among dentists in Chengdu, China. Thus, the present study is aimed at providing the best available evidence on clinical decision-making to manage dental caries in children and the overall benefits. METHODS: The self-designed questionnaire in this study consisted of two main sections, including the sociodemographic characteristics of the respondents and their perception and use of PMCs. The anonymous questionnaire was distributed among 1000 dentists practicing in Chengdu via SO JUMP. RESULTS: The response rate was 45%. Most respondents (69.6%) did not use PMCs. Academic qualification, working specialty, and professional experience were associated with dentists' use of PMCs. The lack of knowledge about the PMC technique was the main obstacle to the dental practitioners' use of PMCs (41.7%). The lack of understanding of the rationale behind PMCs was the main reason for parents' acceptance of PMC restorations (43.6%). Attending continuing education programs was the main approach to learning the PMC restorative technique (59.1%). CONCLUSIONS: The clinical use of PMCs was not very popular in Chengdu city. To promote this restorative technique, knowledge and practical training should be incorporated into routine courses of undergraduate dental education.

Reliability of software-based assessment of paediatric preparations for preformed metal crowns in the simulation laboratory.

PURPOSE: Using software for assessment of restorative work on typodonts in the simulation laboratory may enhance the objective evaluation of student work. The study aimed to evaluate the inter-rater and intra-rater reliability using 3-D scans from the Planmeca Emerald™ intra-oral scanner with Romexis Compare® software for assessing preparations for preformed metal crowns (PMCs). METHODS: Three operators independently recorded 3-D scans and digitally measured the features of 30 PMC preparations on typodont primary teeth (# 75). Using Romexis Compare® software, preparations were measured from mesial, distal and occlusal aspects. Measurements were repeated after 2 weeks. The intraclass correlation coefficient (ICC) was used to measure the reliability of measurements between operators and within the one operator. RESULTS: For measuring the extent of tooth reduction, there was excellent intra-rater reliability for each operator (ICC 0.96-0.99). The highest inter-rater reliability was for measurements of the occlusal surface (0.946 and 0.956), followed by the mesial surface (0.852 and 0.862) and then the distal surface (0.746 and 0.724). CONCLUSION: This method was useful and reliable for measuring features of PMC preparation, but with some limitations. Improving the software to provide specific assistance tools would empower greater uptake of this method as an adjunct to traditional visual grading tool in paediatric dentistry preclinical teaching.

Influência da técnica de preparo sobre o contorno cervical dos laminados cerâmicos: relato de caso / Influence of the preparation technique on the cervical contour of ceramic laminates: a case report / Influencia de la técnica de preparación en el contorno cervical de los laminados cerámicos: reporte del caso

Introdução: Devido à crescente demanda estética, a odontologia restauradora se renova na intenção de alcançar melhores resultados na harmonia do sorriso. Entretanto, a atenção deve voltar-se também aos tecidos periodontais, visto que há uma integração entre material restaurador e os tecidos. Objetivo:Descrever e discutir as etapas clínicas para a confecção de laminados cerâmicos, atentando-se a preparos minimamente invasivos, contorno cervical e fatores que podem intervir na longevidade do procedimento.Relato de caso:Paciente do sexo masculino, 28 anos de idade, compareceu a Associação Brasileira de Odontologia, seção de Alagoas, relatando insatisfação em relação ao tamanho dos seus dentes. Os arcos superior e inferior foram moldados para a obtenção dos modelos de estudo e enceramento diagnóstico. Ao início do tratamento foi orientado ao paciente clareamento dental pela técnica combinada. O preparo dos dentes foi guiado por uma matriz de silicone, sendo estes uniformes e conservadores, seguido de moldagem, fase laboratorial e cimentação final. Finalizado o caso foi realizado o ajuste oclusal solicitando ao paciente que realizasse movimentos de lateralidade e protrusão. Conclusões:A técnica do preparo influência na longevidade dos laminados cerâmicos, por relacioanar-se à adesão e a saúde periodontal. O preparo deve ser mínino e limitado ao esmalte dental sempre que possível, determinando assim um maior e melhor prognóstico (AU).

Introduction:Due to the growing aesthetic demand, restorative dentistry is renewed to achieve better results in smile harmony. However, attention should also be turned to periodontal tissues since there is an integration between restorative material and tissues. Objective:To describe and discuss the clinical steps for the manufacture of laminate veneers, paying attention to minimally invasive preparations, cervical contour, and factors that can intervene in the procedure's longevity. Case report:A 28-year-old male patient attended the Brazilian Dental Association, the Alagoas section, reporting dissatisfaction with his teeth' size. The upper and lower arches were molded to obtain the study and diagnostic waxing models. At the beginning of treatment, the patient was instructed by the combined technique. After the case, the occlusal adjustment was performed, asking the patient to perform laterality and protrusion movements. Conclusions:The preparation technique influences the longevity of laminate veneers due to adherence and periodontal health. The preparation should be minimal and limited to dental enamel whenever possible, thus determining a higher and better prognosis (AU).

Introducción: Debido a la creciente demanda estética, la odontología restauradora se renueva para lograr mejores resultados en la armonía de la sonrisa. Sin embargo, también se debe prestar atención a los tejidos periodontales ya que existe una integraciónentre el material restaurador y los tejidos.Objetivo: Describir y discutir los pasos clínicos para la confección de carillas laminares, prestando atención a las preparaciones mínimamente invasivas, al contorno cervical y a los factores que pueden intervenir en la longevidad del procedimiento.Reporte del caso: Un paciente masculino de 28 años asistió a la Asociación Dental Brasileña, sección de Alagoas, reportando insatisfacción con el tamaño de sus dientes. Los arcos superior e inferior fueron moldeados para obtener los modelos de depilación de estudio y diagnóstico. Al comienzo del tratamiento, el paciente fue instruido por la técnica combinada. La preparación de los dientes fue guiada por una matriz de silicona, siendo estas uniformes y conservadoras, seguidas de moldeo, fase de laboratorio y cementación final. Después del caso, se realizó el ajuste oclusal, pidiendo al paciente que realizara movimientos de lateralidad y protuberancia. Conclusiones: La técnica de preparación influye en la longevidad de los laminados cerámicos, debido a la adherencia y la salud periodontal. La preparación debe ser mínima y limitada al esmalte dental siempre que sea posible, determinando así un pronóstico más alto y mejor (AU).

Marginal Integrity of CAD/CAM Ceramic Crowns Using Two Different Finish Line Designs.

OBJECTIVE: Research on evaluation of crowns made by the latest contemporary dental computer-aided design/computer-aided manufacturing (CAD/CAM) systems for their marginal adaptation is scarce. The purpose of this in vitro study was to evaluate the marginal integrity of crowns fabricated by the latest Chairside Economical Restorations of Esthetic Ceramic (CEREC) system using 2 different finish line preparation designs: chamfer and shoulder. MATERIALS AND METHODS: Typodont teeth were divided equally into 2 groups, A and B. The teeth were prepared for full coverage crowns with a shoulder (group A) and chamfer (group B) finish line design. An experienced prosthodontist prepared all crown preparations. Evaluation of 6 sites per sample was completed by 2 calibrated, experienced prosthodontists using the modified US Public Health Services (USPHS) criteria. The descriptive statistics and Z-test were used to evaluate the results. RESULTS: A total of 180 teeth were included in the study (90 teeth in each group). Only 2 crowns in group A and 1 crown in group B were clinically unacceptable. There was no statistical significance (p = 0.282) between the 2 groups regarding finish line design. CONCLUSIONS: The CEREC system provides clinically acceptable crowns and can safely be utilized in dental treatment. Therefore, CAD/CAM restorations could be considered as a safe treatment modality by dental professionals.