Correlation Between Acquisition of Dental Implant Stability and Hounsfield Units at Dental Implant Placement.

Alveolar bone quality at the implantation site affects the initial stability of dental implant treatment. However, the relationship between bone quality and osseointegration has yet to be evaluated. Herein, we aimed to investigate the effect of bone quality on dental implant stability in osseointegration formation changes. Patients underwent computed tomography imaging before dental implantation at the posterior. Hounsfield units were measured at the platform, middle, and tip sites. Implant stability was measured using resonance frequency analysis immediately and at 3 months postoperatively, in which the difference in implant stability quotients (ISQ) was defined as the change between primary and secondary fixation. In multiple regression analysis, the dependent variable was the change between the immediate and secondary fixations. We included 81 implants that conformed to the criteria. Primary fixation yielded the following results: R2 = 0.117, F = 2.529, and P = .047. The difference between the maxilla and mandible of the implantation site (P = .02) and the platform-site Hounsfield units (P = .019) were identified as significant factors. The following results were obtained regarding the change between the immediate and secondary fixation: R2 = 0.714, F = 40.964, and P < .001. The difference between diameter (P = .008) and the immediate ISQ (P < .001) were identified as significant factors. Overall, the bone quality of the implantation site affected initial fixation; however, it had limited effect on secondary fixation. Our findings clarified the period where bone quality affects dental implant treatment and is expected to advance dental implant treatment.

Evaluation of Vertical Misfit and Torque Loss of Different Abutments for Tri-Channel Type Internal Connection Dental Implants After Mechanical Cycling.

The aim of this study was to evaluate the mechanical behavior of UCLA and Mini-conical abutments for implants with Tri-channel connections regarding torque loss and vertical misfit. Twenty 3-element metal-ceramic fixed partial dentures (FPD) supported by 2 implants were manufactured and divided into 2 groups (n = 10): UCLA (group 1) and Mini-conical Abutments (group 2). The evaluation of torque loss was carried out before and after mechanical cycling, while the vertical fit was evaluated throughout the different stages of manufacturing the prostheses, as well pre- and postcycling (300,000 cycles, 30 N). Statistical analyses of torque loss and vertical misfit were performed using the linear mixed effects model. Both groups showed torque loss after mechanical cycling (P < .05); however, there was no significant percentage differences between them (P = .795). Before cycling, the groups showed a significant difference in terms of vertical misfit values (P < .05); however, this difference was no long observed after cycling (P = .894). Both groups showed torque loss after the cycling test, with no significant difference (P > .05). There was no significant difference in vertical misfit after mechanical cycling; however, in group 1 (UCLA) there was accommodation of the implant-UCLA abutment interface, while group 2 (Mini-conical abutment) did not show changes in the interface with the implant after the test. Both groups behaved similarly regarding the torque loss of the prosthesis retention screws pre- and postmechanical cycling, with greater loss after the test.

Comparison of the Effect of Implant Abutment Surface Modifications on the Retention of Implant-Supported Restorations.

PURPOSE: To evaluate and compare the difference in retention between implant-supported restorations with and without surface modification of the implant abutments. MATERIALS AND METHODS: A total of 30 patients with singletooth implants were restored with cement-retained (Multilink N, Ivoclar) restorations using titanium base abutments (Variobase, Straumann) and randomly assigned surface modifications. Group 1 used nonmodified abutments, group 2 used sandblasted abutments, and group 3 used sandblasted abutments followed by an application of metal primer. All patients were recalled for a baseline examination 6 months after crown placement. The pull-out strength and intergroup distribution of mean pull-out strength were assessed. To assess differences between the three groups, intergroup statistical comparison of continuous variables was done using one-way ANOVA with Tukey correction for multiple group comparisons. RESULTS: The results of the intergroup mean pull-out strength distribution revealed that the distribution of mean ± SD pull-out strength in group 1, group 2, and group 3 were 220.79 ± 94.23, 488.64 ± 84.12, and 705.46 ± 112.75 Ncm, respectively. CONCLUSIONS: Sandblasting followed by the application of metal primer produced the highest retention of porcelain-fused-to-metal (PFM) crowns to titanium base abutments, followed by sandblasting alone, with the least retention being observed with no surface treatment.

Evaluation of the Correlation Between the Structural Parameters of Trabecular Bone in CBCT and the Primary Stability of Dental Implants.

PURPOSE: To investigate the relationship between the structural parameters of trabecular bone obtained from CBCT imaging and the primary stability of dental implants. MATERIALS AND METHODS: Sixty patients underwent implant placement followed by primary stability evaluation via measurement of the insertion torque (IT) and the implant stability quotient (ISQ). Gray values (GV) and the fractal dimension (FD) were also measured using pretreatment CBCT images. RESULTS: FD values showed a positive and significant relationship with ISQ and IT values (P = .017 and P = .004, respectively). Additionally, there was a positive and significant correlation between GV and IT (P = .004) as well as between GV and ISQ (P = .010). FD and GV showed a considerable difference between the maxillary and mandibular jaws and were higher in the mandible. Only FD was significantly different between men and women and was higher in men. In the two age groups (older and younger than 45 years), only GV was considerably higher in people older than 45 (P < .05). CONCLUSIONS: Both fractal dimension and gray values obtained from CBCT are efficient methods for predicting the primary stability of the implant due to their relationship with ISQ and IT values.

Radiographic alveolar bone assessment in correlation with primary implant stability: A systematic review and meta-analysis.

INTRODUCTION: The radiographic examination of alveolar bone using 3D radiographic examination is essential in dental implant treatment planning. Our study aimed to systematically review and quantitatively analyze the correlation between alveolar bone parameters, specifically bone density and cortical bone thickness, assessed using cone beam computed tomography (CBCT) and/or multidetector computed tomography (MDCT); and primary implant stability (PIS) determined using implant stability quotient (ISQ), Periotest® value (PTV), and insertion torque value (ITV). METHODS: This review was registered in the PROSPERO database (registration number CRD42022307245). An electronic literature search was conducted on the PubMed, SCOPUS, and Web of Science databases for papers published until February 2022. The Quality Assessment in Prognostic Studies (QUIPS) tool was used to assess risk of bias. Meta-analyses were conducted to calculate the estimated average correlation coefficient based on a multilevel random-effects model, followed by subgroup analysis. RESULTS: Twenty-six studies were included in this review, consisting of 17 prospective cohort studies, eight retrospective cohort studies, and one nonrandomized controlled trial. A total of 3109 implants placed in 1171 subjects were analyzed. Twenty-three studies were evaluated using meta-analysis. The alveolar bone condition was significantly correlated with ISQ (r = 0.60; p < .001), IT (r = 0.52; p < .001), and PTV (r = -0.42; p < .05). CONCLUSION: Alveolar bone condition is significantly associated with PIS. Low bone density and thin cortical bone can lead to low PIS; therefore, modification of treatment planning and surgical procedures might be needed to avoid poor osseointegration.

Retention of titanium copings to implant-supported fixed dental prostheses.

PURPOSE: The aim of this in vitro study was to assess the effects of using different cements and titanium copings designs on the retention of implant-supported fixed dental prostheses (IFDPs) using a pull-out test. MATERIALS AND METHODS: Fifty zirconia (ZirCAD; Ivoclar Vivadent) and 20 prepolymerized denture acrylic resin (AvaDent) rectangular (36 mm × 12 mm × 8 mm) specimens were milled to mimic the lower left segmental portion of the All-on-Four IFDPs. Cylindrical titanium copings (Variobase; Straumann) (V) were used in 2 prepolymerized denture acrylic resin groups (n = 10) while conical titanium copings (Straumann) (C) were used as a control group for zirconia with 4 groups using cylindrical titanium copings. Before cementation, the outer surfaces of all titanium copings and the intaglio bonding surface of prosthetic specimens were airborne-particle abraded. All specimens were cemented following the manufacturer's recommendations and instructions according to the experimental design. After artificial aging (5000 cycles of 5°C 55°C, dwelling time 20 s; 150 N, 1.5 Hz in a 37°C water bath), all specimens were subjected to retention force testing using a pull-out test using a universal testing machine and a custom fixture with a crosshead speed 5 mm/min. Modes of failure were classified as Type 1, 2, or 3. Retention force values were analyzed by the t-test for the prepolymerized denture acrylic resin specimen groups, and 1-way ANOVA and the Tukey test for the zirconia groups at α = 0.05. RESULTS: Mean and standard deviation retention force values varied from 101.1 ± 67.1 to 509.0 ± 65.2 N for the prepolymerized denture acrylic resin specimen groups. The zirconia groups ranged from 572.8 ± 274.7 to 1416.1 ± 258.0 N. There is no statistically significant difference in retention force values between V and C specimens cementing to zirconia with Panavia SA cement (Kuraray Noritake) (p = 0.587). The retention forces and failure modes were influenced by the cement used (p < 0.05). Modes of failure were predominantly Type 2 (mixed failure) and Type 1 (adhesive fracture from prosthetic materials) except for the quick-set resin group (Type 3, adhesive failure from coping). CONCLUSIONS: When bonding IFDPs onto titanium copings, quick-set resin provided significantly higher retention force for prepolymerized denture acrylic resin prostheses. Conical and cylindrical titanium copings performed similarly when cemented to zirconia with Panavia SA cement under the same protocol. The stability of the bonded interface and retention forces between zirconia prostheses and titanium copings varied from the cement used.

Correlation between Periotest value and implant stability quotient: a systematic review.

OBJECTIVES: To determine, through clinical studies, whether there is a correlation between the Periotest value (PTV) and the implant stability quotient (ISQ). CONTENT: Methods to evaluate the stability of dental implants. SUMMARY: A search was performed in the PubMed, Scopus, and Web of Science databases for articles on the proposed subject up to January 29, 2023, using search terms that combined "resonance frequency analysis" and "Periotest" with "correlation" or "relationship"; and combinations of "implant stability quotient" and "Periotest" with "correlation" or "relationship." The inclusion criteria were clinical studies in English involving human subjects who received dental implants and evaluating the correlation between PTV and ISQ. A total of 46 articles were screened, of which 10 were selected for full-text analysis, and eight articles were included in this review. Based on three articles, 75 % of the results of this systematic review showed a negative correlation between PTV and ISQ, regardless of the type of stability assessed. Based on the remaining five articles, 100 % (regardless of the patient's gender) and 66.66 % of the results showed a negative correlation for primary and secondary stability, respectively. There is a negative correlation between PTV and ISQ for both primary and secondary dental implant stability. OUTLOOK: This review can serve as a reference for the development of methodologies for future clinical studies on this topic.

Influence of diameter and length on primary stability in various implant site densities-An in vitro study in polyurethane blocks.

BACKGROUND: The influence of dental implant length and diameter on primary stability in various bone densities is not well understood. AIM: To in vitro study the effect of length and diameter on resonance frequency analysis (RFA), insertion torque (IT) and displacement (DP) measurements of dental implants in different implant site densities. MATERIALS AND METHODS: Dental implants of four different diameters (Ø 3.5, 4.0, 4.5 and 5.0 mm) and three different lengths (7, 11 and 15 mm) (Neoss Ltd, Harrogate, UK) were placed in polyurethane blocks of three different densities (Sawbones Europe AB, Malmö, Sweden). The primary stability was assessed by RFA (ISQ) (Osstell, Osstell AB, Gothenburg, Sweden) and insertion torque measurements (ITmax in N cm) (iChiropo™, Bien-Air Dental SA, Bienne, Switzerland). In addition, the blocks were mounted in a rig and a lateral force of 25 N cm was applied to the implants and the DP was measured in µm with a micrometer gauge placed on the opposite side of the load transducer. Statistical analyses using linear and quadratic models were applied. RESULTS: Implant length, diameter and block density were found to be significant independent predictors of RFA, ITmax, and DP measurements. Implant length had a strong effect, while the effect of diameter in general was subtle, particularly in the softest block. CONCLUSIONS: Implant length affects primary stability more than implant diameter in polyurethane blocks of uniform density along the whole length of the tested implants.

Insertion Torque and Resonance Frequency Analysis in Tapered and Parallel Dental Implants.

Primary implant stability (PIS) is known to vary with recipient bone mass and density, dental implant design and surgical technique. The objective of this preliminary study was to compare rotational and lateral PIS of same-coronal-diameter conical and parallel implants, using insertion torque recorded with a dental implant motor set and implant stability quotient obtained from resonance frequency analysis (performed with both Osstell and Penguin systems) as measures of rotational and lateral stability, respectively. Additionally, the relationship between PIS and alveolar ridge width (ARW) was explored in both implant types. Sixty dental implants (30 tapered and 30 parallel) were randomly placed with a split-mouth design in 17 patients. Bone density and ARW were estimated from cone beam computed tomography images taken with radiological-surgical templates. Density and width values were similar in the 2 groups (P > .05). Implant coronal diameters were 3.75 mm in all cases, while consistent with the manufacturer's recommendations, final drill bit diameters used were 3.25 and 3.4 mm for parallel and tapered implants, respectively. Insertion torque was higher (P < .05) with parallel implants, but between-group differences in implant stability quotient were not significant (P > .05). In tapered implants, insertion torque was inversely correlated with ARW (P < .001). Notably, significant differences were observed between resonance frequency analysis values from Osstell and Penguin systems (P < .001). In conclusion, future studies should explore how PIS may be influenced by final drill bit size regardless of implant design and potential limits on the effectiveness of tapered implants to achieve good stability in thick low-density bone.

Resonance Frequency Analysis to Assess the Stability of Immediate Implants: A Retrospective Clinical Trial.

Adequate implant primary stability is a key factor to obtain osseointegration and can be measured at insertion by insertion torque (IT) and at different timepoints with resonance frequency analysis (RFA), expressed as an implant stability quotient (ISQ). This retrospective study investigated the correlation between ISQ and IT at implant insertion. All patients who were eligible for this single-cohort retrospective clinical trial were treated with an immediate implant. IT parameters were recorded at implant insertion, and ISQ values were recorded at insertion and at 2-, 4-, and 12-month follow-ups. The study comprised 23 patients who received 32 implants. The mean IT value was 46.87 ± 9.66 Ncm (range: 25 to 65 Ncm), and the mean ISQ value at implant insertion was 71.45 ± 4.24 (range: 63 to 78); these values showed a statistically significant correlation (P < .0001). According to the present data and considering the implant design used in this trial, there is a statistically significant and positive correlation between IT and ISQ values. Thus, ISQ can be used as a reliable method to measure implant stability over time.

Primary Stability Evaluation of a Novel Tapered Implant Inserted in Low-Density Bone Sites: An In Vitro Study.

Purpose: To evaluate primary stability of a new dental implant design in low-density bone sites, compare it with another implant design previously studied in the same bone density, and explore possible correlations between primary stability parameters. Materials and Methods: The study was carried out on fresh humid bovine bone classified as type III. The test group consisted of 30 DS Prime Taper implants (PT), and the control group consisted of 30 Astra Tech EV implants (EV). All the implants were inserted according to the protocol provided by the manufacturer. After placement, variable torque work (VTW), peak insertion torque (pIT), and resonance frequency analysis (RFA) were recorded. Results: Mann-Whitney test showed that the mean VTW and pIT were significantly higher in the test group PT compared to the control group EV; furthermore, statistical analysis showed that the mean RFA was slightly higher in the control group EV but without reaching statistical significance. Pearson correlation analysis showed a very strong positive correlation between pIT and VTW values in both groups; furthermore, it showed a positive correlation between pIT and RFA values and between VTW and RFA values again in both groups. Conclusion: The results showed that the novel tapered implants were able to reach good primary stability in low-density bone sites and that this was superior to parallel-walled implants when measured with VTW and pIT. Moreover, a statistically significant correlation was found between the three methods used to measure implant primary stability.

Techniques for locating the screw access hole in cement-retained implant-supported prostheses: A systematic review.

STATEMENT OF PROBLEM: Different techniques for retrieving cement-retained implant-supported prostheses have been described to minimize damage to the prostheses. Nevertheless, a classification of the described techniques remains ambiguous. PURPOSE: The purpose of this systematic review was to review and classify the described techniques for recording and locating the screw access hole in cement-retained implant-supported prostheses. MATERIAL AND METHODS: A bibliographic search was completed on MEDLINE/PubMed, Web of Science, Scopus, and Cochrane databases. A manual search was also conducted. The articles that described or evaluated techniques for recording and locating the screw access hole of cement-retained implant-supported prostheses were included. Two investigators independently assessed the quality assessment of the studies using the Revised Cochrane risk of bias tool for randomized trials. A third examiner was consulted to resolve the lack of consensus. RESULTS: A total of 30 articles were included. The different methods were classified according to whether the screw access hole location was registered before or after cementation. The precementation techniques were classified into 4 subgroups: identification marks, photographic records, digital files, and precementation screw access hole location guides. The postcementation techniques were subdivided into 2 subgroups: radiographic records and postcementation screw access hole location guides. CONCLUSIONS: Different techniques have been proposed to facilitate the location of the screw access hole in cement-retained implant-supported restorations. Although the evidence is scarce, studies seem to ascertain that some techniques, such as the use of drilling guides, orientation with cone beam computed tomography images, or holes made in the metal framework, can increase the retrievability of cement-retained implant-supported prostheses and decrease complications in the location of the screw access hole. The proposed classification summarizes precementation and postcementation techniques and provides a tool to decide the most suitable for each specific clinical situation.

Screwmentable implant-supported prostheses: A systematic review.

STATEMENT OF PROBLEM: Screwmentable prostheses were developed to combine the benefits of screw retention and cement retention. However, data are limited on the clinical performance of this type of prosthesis. PURPOSE: The purpose of this systematic review was to collect scientific evidence on screwmentable prostheses and evaluate their long-term clinical behavior. MATERIAL AND METHODS: An electronic search was conducted by 2 independent reviewers for articles published in scientific dental journals in English from 2004 to April 2020. The search strategy followed the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) guidelines. Inclusion criteria were scientific studies concerning the screwmentable type of prosthesis. RESULTS: The search provided 494 records. Of these, 24 studies fulfilled the inclusion criteria and were included in the review. The included articles presented significant heterogeneity concerning the manufacturing process and the materials used. One randomized clinical trial, 2 prospective clinical studies, 14 in vitro studies, 3 protocol descriptions, 1 case series, and 3 case reports were included. CONCLUSIONS: Based on the systematic search of the literature, it is concluded that the screwmentable prosthesis combines advantages of both cement-retained and screw-retained restorations, including passive fit, retrievability, excess cement control, tissue-friendly emergence profile, and improved esthetics. Nevertheless, data from well-designed clinical trials are limited, and further research is required to provide evidence on their long-term clinical behavior.

Deformation of implant retaining screws-Study with stereoscopic microscopy and microCT.

BACKGROUND: The prosthetic screw fixes the prostheses to the implants. Upon osteointegration, the untightening of the prosthetic screw is the most common problem in oral rehabilitation with implants. OBJECTIVE: To study the deformation of the implant retaining hexagonal screw head. METHODS: This investigation used two methods for evaluating the screw head's area of deformation (mm2 ): a stereoscopic microscopy and micro computed tomography (microCT). For stereoscopic microscopy, 16 titanium alloy (T) and 16 titanium gold-plated alloy (G) screws of the Zimmer Biomet™ brand were used, divided into eight groups: group 0 (control group), groups T1 and G1 (screws tightened 10 times to 20 Ncm), the groups T2 and G2 (screws tightened 20 times to 20 Ncm) and the groups T3 and G3 (screws tightened 10 times to 30 Ncm). In the study with microCT, one screw was randomly chosen from each of the groups described above to perform the scanning by microCT. RESULTS: When comparing the type of screw material using stereoscopic microscopy, no statistically significant differences were found (p > 0.05). Contrarily, different number of successive grips and different torque value showed statistically significant differences in the head section of the retaining screws (p < 0.05). The observation by microCT showed the torque applied is crucial to the head deformation in titanium screws. In gold-plated screws the successive tightening appears to be pivotal. CONCLUSION: Titanium and gold screws tend to behave similarly. By increasing the tightening cycles and the torque values of protocols greater levels of deformations can be expected. In general, microCT data showed better results for gold-plated titanium alloy. CLINICAL SIGNIFICANCE: To control severe screw head deformation and the impossibility of untightening the implant's restoration, clinicians should avoid extreme torque values and prevent surpassing 10 tightening cycles.

Prótese overdenture: sistema o'ring / Overdenture prosthesis: o'ring system

Overdenture é uma prótese total que se caracteriza por usar apoios retentivos para que aumente sua estabilidade e retenção na cavidade bucal, gerando assim menor desconforto ao paciente e melhor adaptação. A Prótese overdenture dentossuportada necessita de elementos dentais remanescentes com canais tratados endodonticamente e que possuam suporte periodontal adequado. O objetivo deste relato de caso clínico é expor a sequência de confecção de uma prótese overdenture dentossuportada maxilar associada a uma prótese total convencional mandibular, com os passos clínicos detalhados por meio de uma abordagem teórica e visual. Esse tipo de reabilitação favorece a adaptação do paciente à nova condição, visto que o uso de próteses totais convencionais pode causar certo desconforto ao paciente devido à falta de retenção e estabilidade. Essa manutenção dos dentes remanescentes favorece à manutenção óssea e a futura decisão do paciente em optar pela instalação de implantes dentários, podendo confeccionar próteses implantorretidas (overdentures) ou implantossuportadas (protocolo).O Paciente demonstrou-se satisfeito com o resultado estético e funcional após a instalação da prótese concretizando que o tratamento é viável(AU)

Overdenture is a denture that utilizing retentive supports for increase stability and retention in oral cavity. The tooth-supported overdenture require dental elements with root canal therapy and good periodontal support. The aim of this study is to report the confection of a maxillary tooth-supported overdenture associated with mandibular denture and your clinical steps. This rehabilitation promotes the patient's adaptation the new condition, since the use of conventional dentures may cause discomfort due to lack of retention and stability. The preservation of dental elements promotes bone maintenance and forthcoming decision of the patient in the installation of dental implants that can choose implantretained or implant-supported prosthesis. Patient was satisfied with aesthetic and functional result after installation of prosthesis(AU)

Intra- and inter-operator concordance of the resonance frequency analysis. A cross-sectional and prospective clinical study.

OBJECTIVE: Resonance frequency analysis (RFA) provides an evaluation of implant stability over time. This analysis is a non-invasive, precise, and objective method. Several studies compare the RFA system with other devices. However, few investigations analyze repeatability and reproducibility between different operators. The aim of this study was to evaluate the intra- and inter-operator concordance of the Osstell® ISQ. MATERIAL AND METHODS: RFA measurements were performed with Osstell® ISQ in a total of 37 implants placed in 21 patients. At the time of implant placement, 6 measurements per implant were taken by three different experienced operators. Three measurements were carried out consecutively and three by removing and placing the SmartPeg-Osstell® to assess intra-operator and inter-operator agreement. RESULTS: Intra-operator concordance according to the intraclass correlation coefficient (ICC) showed high concordance. The ICC values were higher than 0.9 (p < 0.0001) for consecutive measures and alternative measures, being almost perfect of Landis & Koch classification. For inter-operator concordance The ICC was 0.709 (p < 0.0001) and 0.670 (p < 0.0001) for consecutive and alternative measures, respectively, both estimates being in the substantial category. In torque and ISQ values, no statistically significant differences were observed when operators and measurements were compared. CONCLUSIONS: Osstell® ISQ system was stable both in intra-operator and inter-operator measurements. This device has excellent repeatability and reproducibility, demonstrating reliability to measure the stability of dental implants. CLINICAL RELEVANCE: Resonance frequency analysis (RFA) is a non-invasive, objective, and reliable diagnostic method to determine the ideal moment to load the implant, as well as to predict possible failures.

Validation of an implant stability measurement device using the percussion response: a clinical research study.

BACKGROUND: Several devices have been developed to measure implant-bone stability as an indicator of successful implant treatment; these include Osstell®, which measures the implant stability quotient (ISQ), and the more recent AnyCheck®, which relies on percussion for the implant stability test (IST). These devices make it possible to measure implant stability. However, no studies have compared the performance of AnyCheck® and Osstell® (i.e., IST and ISQ values) in clinical practice. Therefore, this study aimed to determine the correlation between primary and secondary implant stability using the Osstell® and AnyCheck® devices. METHODS: Ten patients (7 women; age [mean ± standard deviation]: 49.1 ± 13.3 years) with partially edentulous jaws who received a total of 15 implants were included. IST (AnyCheck®) and ISQ (Osstell®) values were measured immediately after implantation and at 1, 2, 3, 4, and 6 weeks post-implantation. Each measurement was performed three times, and the average value was used as the result. The correlation between measurements obtained using the two devices was determined using Spearman's rank correlation coefficient. RESULTS: The IST values ranged from 79.1 ± 2.87 to 82.4 ± 2.65. The ISQ values ranged from 76.0 ± 2.8 to 80.2 ± 2.35. Spearman's rank correlation coefficient was r = 0.64 immediately after implantation, r = 0.29 at 1 week, r = 0.68 at 2 weeks, r = 0.53 at 3 weeks, r = 0.68 at 4 weeks, and r = 0.56 at 6 weeks. A positive correlation was found in all cases, except at week 1 when the correlation was weak; the IST and ISQ values decreased the most during the first postoperative week and increased during the second week. The IST values were also slightly higher at all measurement points. CONCLUSION: The ability to assess implant stability without removing the abutment during healing is essential for determining the timing of loading without the risk of bone resorption. The results of this study suggest that AnyCheck® is useful for determining primary and secondary implant stability.

Is Resonance Frequency Analysis a Reliable Evaluation for Primary Stability of Implants Without Apical Contact?

PURPOSE: The primary stability of dental implants is one of the most crucial factors for providing long-term success of osseointegration. Vertical deficiencies, such as those due to maxillary sinus pneumatization, may cause a severe vertical limitation to residual bone height. This study aimed to examine the primary stabilization of implants without apical contacts. MATERIALS AND METHODS: Eighty bone-level implants (4.1-mm diameter/10-mm length) were placed into polyurethane test blocks without apical contacts. According to coronal bone-to-implant contact, groups were set as 4, 6, 8, and 10 mm, respectively. Resonance frequency analysis (RFA) using a SmartPeg was performed separately toward the transversal and horizontal axes by two independent researchers. Data were statistically compared for interobserver and among groups. RESULTS: Interobserver reliability varied from moderate to excellent (intraclass correlation coefficient [ICC]: 0.629 to 0.985). There were no significant differences among the 6 mm, 8 mm, and 10 mm groups, although the 4 mm group showed the significantly lowest stability (P < .001). Transversal and longitudinal measurements of the same groups did not show a parallel correlation statistically. CONCLUSION: RFA values may be affected by the finger torque in tightening of the SmartPeg among different researchers. Fully placed implants did not significantly show the highest stability among various apically contactless groups. Consequently, RFA should not be used alone to evaluate primary stability for implants without an apical contact.

The influence of implant design on implant stability in low-density bone under guided surgical template in inexperienced surgeons: A pilot randomized controlled clinical trial using resonance frequency analysis.

INTRODUCTION: There are several factors that greatly influence implant stability with implant design being a paramount factor; however, few studies investigate its impact. AIM: To investigate the implant stability in relation to two different implant designs, a cylindrical shaped single-threaded design (CS/ST) and a tapered shaped double-threaded design (TS/DT) using resonance frequency analysis over the first 8 weeks after implantation. MATERIALS AND METHODS: Twenty-eight implants were randomly allocated using computer-generated random numbers into two groups and were placed as single tooth implant in the posterior arch in human jaw as specimens. iCAT™ CBCT scan (Hatfield, PA) was used to determine the bone density according to Misch's Bone classification. The osseotomy sites were prepared and implants were placed with guided surgical template by inexperienced surgeons which were prepared with the same implant planning software (3shape® implant studio). The implant stability was measured using the resonance frequency analysis Osstell® ISQ (Osstell AB, Sweden) on the implant level over the first 8 weeks at three different time intervals. A mean implant stability quotient (ISQ) value was recorded at each measurement time points. The first ISQ of each implant recorded at the time of implant placement were considered as baseline and were the so-called primary stability. RESULTS: All 28 dental implants were analyzed. A similar pattern of implant stability changes was observed in both implant designs. A significant decreased was found at the first 4 weeks after implantation (p < 0.05) before ascending to maximum cumulative stability by the eighth week (p < 0.05). Between the two groups, TS/DT group had a higher mean ISQ values than that of the CS/ST group at all three observation periods but did not reach statistical significance (p = 0.69). Regarding different types of bone, TS/DT showed a significant difference in mean ISQ values in D4 bone. To date, all 28 implants are in function with no failure/and or complications. CONCLUSIONS: The difference in implant design did not significantly influence the implant stability. TS/DT shows superiority over CS/ST when placed in D4 bone and offer a significant advantage due to their positive bounce back of the ISQ values by the eighth week after implant installation. CLINICAL TRIAL REGISTRATION: TCTR20211020005.

The effect of different cleansing methods for removing temporary cement on the tensile bond force of permanently cemented implant-supported metal copings: An in vitro study.

OBJECTIVES: Complete cleaning of temporary cement before permanent cementation of cement-retained implant-supported prosthesis (CISP) when recementing the crown is critical. This study evaluated the effect of different cleaning methods for removing traces of temporary cement on the final tensile bond force (TBF) of CISP recemented with resin cement. MATERIALS AND METHODS: Seventy computer-aided design/computer-aided manufacturing metal implant-supported copings were prepared and distributed into seven groups (N = 10). Copings of six groups (60 samples) were cemented with temporary cement with eugenol and subjected to 5000 thermocycling. After debonding by a universal testing machine, the internal surfaces of the copings were cleaned using one of the six following methods: 1-an ultrasonic water bath (UW), 2-sandblasting, then washing with water (SW), 3-sandblasting and an ultrasonic water bath (SUW), 4-an ultrasonic isopropyl alcohol bath (UA), 5-sandblasting, then washing with isopropyl alcohol (SA) or 6-sandblasting and an ultrasonic isopropyl alcohol bath (SUA). Then the subjects were subsequently cemented by dual-cure self-adhesive resin cement. In the seventh group (control, N = 10), the copings were cemented by dual-cure self-adhesive resin cement without the temporization phase. The TBF was tested using a universal testing machine with a cross-head speed of 1 mm/min. Two-way analysis of variance (ANOVA) and post-hoc Tamhane tests were used for statistical analysis at a significance level of α = .05. RESULTS: The maximum mean of TBF value was observed in SUA group (845 ± 203 N), and the minimum was observed in the temporary cement group (49 ± 20 N). All groups which were cleaned with isopropyl alcohol showed significantly higher TBF values compared with those cleaned with water. CONCLUSIONS: Cleaning of the inner surface of metal copings after debonding with sandblasting and isopropyl alcohol results in the highest value of TBF by eliminating the effect of remaining eugenol and removing traces of temporary cements.