In vivo axial load-share ratio measurement using a novel hexapod system for safe external fixator removal.

BACKGROUND: External fixation is widely used in the treatment of traumatic fractures; however, orthopedic surgeons encounter challenges in deciding the optimal time for fixator removal. The axial load-share ratio (LS) of the fixator is a quantitative index to evaluate the stiffness of callus healing. This paper introduces an innovative method for measuring the LS and assesses the method's feasibility and efficacy. Based on a novel hexapod LS-measurement system, the proposed method is to improve the convenience and precision of measuring LS in vivo, hence facilitating the safe removal of external fixators. METHODS: A novel hexapod system is introduced, including its composition, theoretical model, and method for LS measurement. We conducted a retrospective study on 82 patients with tibial fractures treated by the Taylor Spatial Frame in our hospital from September 2018 to June 2020, of which 35 took LS measurements with our novel method (Group I), and 47 were with the traditional method (Group II). The external fixator was removed when the measurement outcome (LS < 10%) was consistent with the surgeon's diagnosis based on the clinical and radiological assessment (bone union achieved). RESULTS: No significant difference was found in the fracture healing time (mean 25.3 weeks vs. 24.9 weeks, P > 0.05), frame-wearing duration (mean 25.5 weeks vs. 25.8 weeks, P > 0.05), or LS measurement frequency (mean 1.1 times vs. 1.2 times, P > 0.05). The measurement system installation time in Group I was significantly shorter compared to Group II (mean 14.8 min vs. 81.3 min, P < 0.001). The LS value of the first measurement in Group I was lower than that of Group II (mean 5.1% vs. 6.9%, P = 0.011). In Group I, the refracture rate was 0, but in Group II it was 4.3% (2/47, P > 0.05). CONCLUSION: The novel hexapod LS-measurement system and involved method demonstrated enhanced convenience and precision in measuring the LS of the external fixator in vivo. The LS measurement indicates the callus stiffness of fracture healing, and is applicable to evaluate the safety of removing the fixator. Consequently, it is highly recommended for widespread adoption in clinical practice.

An evaluation of the effects of localised skin cooling on microvascular, inflammatory, structural, and perceptual responses to sustained mechanical loading of the sacrum: A study protocol.

This study protocol aims to investigate how localised cooling influences the skin's microvascular, inflammatory, structural, and perceptual tolerance to sustained mechanical loading at the sacrum, evaluating factors such as morphology, physiology, and perceptual responses. The protocol will be tested on individuals of different age, sex, skin tone and clinical status, using a repeated-measure design with three participants cohorts: i) young healthy (n = 35); ii) older healthy (n = 35); iii) spinal cord injured (SCI, n = 35). Participants will complete three testing sessions during which their sacrum will be mechanically loaded (60 mmHg; 45 min) and unloaded (20 min) with a custom-built thermal probe, causing pressure-induced ischemia and post-occlusive reactive hyperaemia. Testing sessions will differ by the probe's temperature, which will be set to either 38°C (no cooling), 24°C (mild cooling), or 16°C (strong cooling). We will measure skin blood flow (via Laser Doppler Flowmetry; 40 Hz); pro- and anti-inflammatory biomarkers in skin sebum (Sebutape); structural skin properties (Optical Coherence Tomography); and ratings of thermal sensation, comfort, and acceptance (Likert Scales); throughout the loading and unloading phases. Changes in post-occlusive reactive hyperaemia will be considered as the primary outcome and data will be analysed for the independent and interactive effects of stimuli's temperature and of participant group on within- and between-subject mean differences (and 95% Confidence Intervals) in peak hyperaemia, by means of a 2-way mixed model ANOVA (or Friedman). Regression models will also be developed to assess the relationship between absolute cooling temperatures and peak hyperaemia. Secondary outcomes will be within- and between-subject mean changes in biomarkers' expression, skin structural and perceptual responses. This analysis will help identifying physiological and perceptual thresholds for the protective effects of cooling from mechanically induced damage underlying the development of pressure ulcers in individuals varying in age and clinical status.

Analysis of cartilage loading and injury correlation in knee varus deformity.

Knee varus (KV) deformity leads to abnormal forces in the different compartments of the joint cavity and abnormal mechanical loading thus leading to knee osteoarthritis (KOA). This study used computer-aided design to create 3-dimensional simulation models of KOA with varying varus angles to analyze stress distribution within the knee joint cavity using finite element analysis for different varus KOA models and to compare intra-articular loads among these models. Additionally, we developed a cartilage loading model of static KV deformity to correlate with dynamic clinical cases of cartilage injury. Different KV angle models were accurately simulated with computer-aided design, and the KV angles were divided into (0°, 3°, 6°, 9°, 12°, 15°, and 18°) 7 knee models, and then processed with finite element software, and the Von-Mises stress distribution and peak values of the cartilage of the femoral condyles, medial tibial plateau, and lateral plateau were obtained by simulating the human body weight in axial loading while performing the static extension position. Finally, intraoperative endoscopy visualization of cartilage injuries in clinical cases corresponding to KV deformity subgroups was combined to find cartilage loading and injury correlations. With increasing varus angle, there was a significant increase in lower limb mechanical axial inward excursion and peak Von-Mises stress in the medial interstitial compartment. Analysis of patients' clinical data demonstrated a significant correlation between varus deformity angle and cartilage damage in the knee, medial plateau, and patellofemoral intercompartment. Larger varus deformity angles could be associated with higher medial cartilage stress loads and increased cartilage damage in the corresponding peak stress area. When the varus angle exceeds 6°, there is an increased risk of cartilage damage, emphasizing the importance of early surgical correction to prevent further deformity and restore knee function.

Time to full weight-bearing with the use of a calcium sulfate-calcium phosphate bone substitute as a bone void filler following extended curettage in the treatment of primary benign bone tumours.

PURPOSE: The primary objective of this study was to determine time to full weight-bearing after the use of a calcium-sulfate-calcium phosphate bone substitute (CaSO4/CaPO4) as a bone void filler in the treatment of primary benign bone tumours following intralesional curettage. The secondary objectives were to determine surgical complications and recurrence rates. METHODS: Retrospective review of patients identified from a surgeon-specific orthopaedic oncology database, who underwent curettage of benign bone tumours and subsequent bone void filling with CaSO4/CaPO4. RESULTS: A total of 39 patients (20 males, 19 females) met inclusion criteria with an average age of 31 years (range: 13 to 62 years), a median follow-up of 3.7 years, and a maximum follow-up of 11 years. The most common tumour diagnosis was giant cell tumour of bone (GCT) (n = 19), and the most common location was the proximal tibia (n = 9). The mean volume of tumour excised was 74.1 cm3 including extraosseous bone expansion due to tumour growth, with a mean of volume of 21.4 mL of CaSO4/CaPO4 used to fill the intraosseous cavitary defects to restore normal bone anatomy. None of the lesions required additional internal fixation. The primary outcome measure, average time to full weight-bearing/full range of motion, was 11 weeks and 6 weeks for upper and lower extremity lesions, respectively. Secondary outcomes included tumour recurrence requiring reoperation in five patients and infection requiring reoperation in two patients. CONCLUSION: This study demonstrates that CaSO4/CaPO4 is a viable option as a bone void filler in the reconstruction of cavitary defects following removal of primary benign bone tumours. CaSO4/CaPO4 provides sufficient bone regeneration early in the post-operative period to allow progression to full weight-bearing within weeks without the need for internal fixation. There were no graft-specific complications noted.

Numerical evaluation of internal femur osteosynthesis based on a biomechanical model of the loading in the proximal equine hindlimb.

Femoral fractures are often considered lethal for adult horses because femur osteosynthesis is still a surgical challenge. For equine femur osteosynthesis, primary stability is essential, but the detailed physiological forces occurring in the hindlimb are largely unknown. The objective of this study was to create a numerical testing environment to evaluate equine femur osteosynthesis based on physiological conditions. The study was designed as a finite element analysis (FEA) of the femur using a musculoskeletal model of the loading situation in stance. Relevant forces were determined in the musculoskeletal model via optimization. The treatment of four different fracture types with an intramedullary nail was investigated in FEA with loading conditions derived from the model. The analyzed diaphyseal fracture types were a transverse (TR) fracture, two oblique fractures in different orientations (OB-ML: medial-lateral and OB-AP: anterior-posterior) and a "gap" fracture (GAP) without contact between the fragments. For the native femur, the most relevant areas of increased stress were located distally to the femoral head and proximally to the caudal side of the condyles. For all fracture types, the highest stresses in the implant material were present in the fracture-adjacent screws. Maximum compressive (-348 MPa) and tensile stress (197 MPa) were found for the GAP fracture, but material strength was not exceeded. The mathematical model was able to predict a load distribution in the femur of the standing horse and was used to assess the performance of internal fixation devices via FEA. The analyzed intramedullary nail and screws showed sufficient stability for all fracture types.

Probability of Occult Ankle Fracture Based on Radiograph-Measured Swelling.

INTRODUCTION: Pediatric ankle injuries are a common presentation in the emergency department (ED). A quarter of pediatric ankle fractures show no radiographic evidence of a fracture. Physicians often correlate non-weight bearing and tenderness with an occult fracture. We present this study to predict the probability of an occult fracture using radiographic soft-tissue swelling on initial ED radiographs. METHODS: This is a retrospective study at a Level 1 pediatric trauma center from 2021 to 22. Soft-tissue swelling between the lateral malleolus and skin was measured on radiographs, and weight-bearing status was documented. Statistical analysis was conducted using Stata software. DISCUSSION: The study period involved 32 patients with an occult fracture, with 8 (25%) diagnosed with a fracture on follow-up radiographs. The probability of an occult fracture was calculated as a function of the ankle swelling in millimeters (mm) using a computer-generated predictive model. False-negative and false-positive rates were plotted as a function of the degree of ankle swelling. CONCLUSION: Magnitude of ankle soft-tissue swelling as measured on initial ED radiographs is predictive of an occult fracture. Although weight-bearing status was not a sign of occult fracture, it improves the predictive accuracy of soft-tissue swelling.

Effects of various load magnitudes on ACL: an in vitro study using adolescent porcine stifle joints.

INTRODUCTION: The escalating incidence of anterior cruciate ligament (ACL) injuries, particularly among adolescents, is a pressing concern. The study of ACL biomechanics in this demographic presents challenges due to the scarcity of cadaveric specimens. This research endeavors to validate the adolescent porcine stifle joint as a fitting model for ACL studies. METHODS: We conducted experiments on 30 fresh porcine stifle knee joints. (Breed: Yorkshire, Weight: avg 90 lbs, Age Range: 2-4 months). They were stored at - 22 °C and a subsequent 24-h thaw at room temperature before being prepared for the experiment. These joints were randomly assigned to three groups. The first group served as a control and underwent only the load-to-failure test. The remaining two groups were subjected to 100 cycles, with forces of 300N and 520N, respectively. The load values of 300N and 520N correspond to three and five times the body weight (BW) of our juvenile porcine, respectively. RESULT: The 520N force demonstrated a higher strain than the 300N, indicating a direct correlation between ACL strain and augmented loads. A significant difference in load-to-failure (p = 0.014) was observed between non-cyclically loaded ACLs and those subjected to 100 cycles at 520N. Three of the ten samples in the 520N group failed before completing 100 cycles. The ruptured ACLs from these tests closely resembled adolescent ACL injuries in detachment patterns. ACL stiffness was also measured post-cyclical loading by applying force and pulling the ACL at a rate of 1 mm per sec. Moreover, ACL stiffness measurements decreased from 152.46 N/mm in the control group to 129.42 N/mm after 100 cycles at 300N and a more significant drop to 86.90 N/mm after 100 cycles at 520N. A one-way analysis of variance (ANOVA) and t-test were chosen for statistical analysis. CONCLUSIONS: The porcine stifle joint is an appropriate model for understanding ACL biomechanics in the skeletally immature demographic. The results emphasize the ligament's susceptibility to injury under high-impact loads pertinent to sports activities. The study advocates for further research into different loading scenarios and the protective role of muscle co-activation in ACL injury prevention.

Strain rate-dependent failure mechanics of the intervertebral disc under tension/compression and constitutive analysis.

BACKGROUND: The intervertebral disc exhibits not only strain rate dependence (viscoelasticity), but also significant asymmetry under tensile and compressive loads, which is of great significance for understanding the mechanism of lumbar disc injury under physiological loads. OBJECTIVE: In this study, the strain rate sensitive and tension-compression asymmetry of the intervertebral disc were analyzed by experiments and constitutive equation. METHOD: The Sheep intervertebral disc samples were divided into three groups, in order to test the strain rate sensitive mechanical behavior, and the internal displacement as well as pressure distribution. RESULTS: The tensile stiffness is one order of magnitude smaller than the compression stiffness, and the logarithm of the elastic modulus is approximately linear with the logarithm of the strain rate, showing obvious tension-compression asymmetry and rate-related characteristics. In addition, the sensitivity to the strain rate is the same under these two loading conditions. The stress-strain curves of unloading and loading usually do not coincide, and form a Mullins effect hysteresis loop. The radial displacement distribution is opposite between the anterior and posterior region, which is consistent with the stress distribution. By introducing the damage factor into ZWT constitutive equation, the rate-dependent viscoelastic and weakening behavior of the intervertebral disc can be well described.

Comparative finite element analysis of the first thoracic vertebra in artiodactyls.

Artiodactyls exhibit a striking diversity of the cervical vertebral column in terms of length and overall mobility. Using finite element analysis, this study explores the morphology at the cervico-thoracic boundary and its performance under loads in artiodactyls with different habitual neck postures and body sizes. The first thoracic vertebra of 36 species was loaded with (i) a compressive load on the vertebral body to model the weight of the head and neck exerted onto the trunk; and (ii) a tensile load at the spinous process to model the pull via the nuchal ligament. Additional focus was laid on the peculiar shape of the first thoracic vertebra in giraffes. We hypothesized that a habitually upright neck posture should be reflected in the greater ability to withstand compressive loads compared to tensile loads, whereas for species with a habitually suspended posture it should be the opposite. In comparison to species with a suspended posture, species with an upright posture exhibited lower stress (except Giraffidae). For compressive loads in larger species, stress surprisingly increased. Tensile loads in larger species resulted in decreased stress only in species with an intermediate or suspensory neck posture. High stress under tensile loads was mainly reflecting the relative length of the spinous process, while high stress under compressive loads was common in more "bell"-shaped vertebral bodies. The data supports a stability-mobility trade-off at the cervico-thoracic transition in giraffes. Performance under load at the cervico-thoracic boundary is indicative of habitual neck posture and is influenced by body size.

Experimental Evaluation of Pedestrian-Induced Multiaxial Gait Loads on Footbridges: Effects of the Structure-to-Human Interaction by Lateral Vibrating Platforms.

The introduction of resistant and lightweight materials in the construction industry has led to civil structures being vulnerable to excessive vibrations, particularly in footbridges exposed to human-induced gait loads. This interaction, known as Human-Structure Interaction (HSI), involves a complex interplay between structural vibrations and gait loads. Despite extensive research on HSI, the simultaneous effects of lateral structural vibrations with fundamental frequencies close to human gait frequency (around 1.0 Hz) and wide amplitudes (over 30.0 mm) remain inadequately understood, posing a contemporary structural challenge highlighted by incidents in iconic bridges like the Millennium Bridge in London, Solferino Bridge in Paris, and Premier Bridge in Cali, Colombia. This paper focuses on the experimental exploration of Structure-to-Human Interaction (S2HI) effects using the Human-Structure Interaction Multi-Axial Test Framework (HSI-MTF). The framework enables the simultaneous measurement of vertical and lateral loads induced by human gait on surfaces with diverse frequency ranges and wide-amplitude lateral harmonic motions. The study involved seven test subjects, evaluating gait loads on rigid and harmonic lateral surfaces with displacements ranging from 5.0 to 50.0 mm and frequency content from 0.70 to 1.30 Hz. A low-cost vision-based motion capture system with smartphones analyzed the support (Tsu) and swing (Tsw) periods of human gait. Results indicated substantial differences in Tsu and Tsw on lateral harmonic protocols, reaching up to 96.53% and 58.15%, respectively, compared to rigid surfaces. Normalized lateral loads (LL) relative to the subject's weight (W0) exhibited a linear growth proportional to lateral excitation frequency, with increased proportionality constants linked to higher vibration amplitudes. Linear regressions yielded an average R2 of 0.815. Regarding normalized vertical load (LV) with respect to W0, a consistent behavior was observed for amplitudes up to 30.0 mm, beyond which a linear increase, directly proportional to frequency, resulted in a 28.3% increment compared to rigid surfaces. Correlation analyses using Pearson linear coefficients determined relationships between structural surface vibration and pedestrian lateral motion, providing valuable insights into Structure-to-Human Interaction dynamics.

Effects of added trunk load on the in vivo kinematics of talocrural and subtalar joints during landing.

BACKGROUND: Landing from heights is a common movement for active-duty military personnel during training. And the additional load they carry while performing these tasks can affect the kinetics and ankle kinematic of the landing. Traditional motion capture techniques are limited in accurately capturing the in vivo kinematics of the talus. This study aims to investigate the effect of additional trunk load on the kinematics of the talocrural and subtalar joints during landing, using a dual fluoroscopic imaging system (DFIS). METHODS: Fourteen healthy male participants were recruited. Magnetic resonance imaging was performed on the right ankle of each participant to create three-dimensional (3D) models of the talus, tibia, and calcaneus. High-speed DFIS was used to capture the images of participants performing single-leg landing jumps from a height of 40 cm. A weighted vest was used to apply additional load, with a weight of 16 kg. Fluoroscopic images were acquired with or without additional loading condition. Kinematic data were obtained by importing the DFIS data and the 3D models in virtual environment software for 2D-3D registration. The kinematics and kinetics were compared between with or without additional loading conditions. RESULTS: During added trunk loading condition, the medial-lateral translation range of motion (ROM) at the talocrural joint significantly increased (p < 0.05). The subtalar joint showed more extension at 44-56 ms (p < 0.05) after contact. The subtalar joint was more eversion at 40-48 ms (p < 0.05) after contact under the added trunk load condition. The peak vertical ground reaction force (vGRF) significantly increased (p < 0.05). CONCLUSIONS: With the added trunk load, there is a significant increase in peak vGRF during landing. The medial-lateral translation ROM of the talocrural joint increases. And the kinematics of the subtalar joint are affected. The observed biomechanical changes may be associated with the high incidence of stress fractures in training with added load.

Load carriage changes tibiofemoral arthrokinematics during ambulatory tasks in recruit-aged women.

The introduction of women into U.S. military ground close combat roles requires research into sex-specific effects of military training and operational activities. Knee osteoarthritis is prevalent among military service members; its progression has been linked to occupational tasks such as load carriage. Analyzing tibiofemoral arthrokinematics during load carriage is important to understand potentially injurious motion and osteoarthritis progression. The study purpose was to identify effects of load carriage on knee arthrokinematics during walking and running in recruit-aged women. Twelve healthy recruit-aged women walked and ran while unloaded (bodyweight [BW]) and carrying additional + 25%BW and + 45%BW. Using dynamic biplane radiography and subject-specific bone models, tibiofemoral arthrokinematics, subchondral joint space and center of closest contact location between subchondral bone surfaces were analyzed over 0-30% stance (separate one-way repeated measures analysis of variance, load by locomotion). While walking, medial compartment contact location was 5% (~ 1.6 mm) more medial for BW than + 45%BW at foot strike (p = 0.03). While running, medial compartment contact location was 4% (~ 1.3 mm) more lateral during BW than + 25%BW at 30% stance (p = 0.04). Internal rotation was greater at + 45%BW compared to + 25%BW (p < 0.01) at 30% stance. Carried load affects tibiofemoral arthrokinematics in recruit-aged women. Prolonged load carriage could increase the risk of degenerative joint injury in physically active women.

A novel in-vitro model of intervertebral disc degeneration using hyperphysiological loading.

Intervertebral disc (IVD) degeneration includes changes in tissue biomechanics, physical attributes, biochemical composition, disc microstructure, and cellularity, which can all affect the normal function of the IVD, and ultimately may lead to pain. The purpose of this research was to develop an in-vitro model of degeneration that includes the evaluation of physical, biomechanical, and structural parameters, and that does so over several load/recovery periods. Hyperphysiological loading was used as the degenerative initiator with three experimental groups employed using bovine coccygeal IVD specimens: Control; Single-Overload; and Double-Overload. An equilibrium stage comprising a static load followed by two load/recovery periods was followed by six further load/recovery periods. In the Control group all load/recovery periods were the same, comprising physiological cyclic loading. The overload groups differed in that hyperphysiological loading was applied during the 4th loading period (Single-Overload), or the 4th and 5th loading period (Double-Overload). Overloading led to a significant reduction in disc height compared to the Control group, which was not recovered in subsequent physiological load/recovery periods. However, there were no significant changes in stiffness. Overloading also led to significantly more microstructural damage compared to the Control group. Taking all outcome measures into account, the overload groups were evaluated as replicating clinically relevant aspects of moderate IVD degeneration. Further research into a potential dose-effect, and how more severe degeneration can be replicated would provide a model with the potential to evaluate new treatments and interventions for different stages of IVD degeneration.

The effect of early weight-bearing and later weight-bearing rehabilitation interventions on outcomes after ankle fracture surgery: A systematic review and meta-analysis of randomised controlled trials.

OBJECTIVE: This systematic review aimed to analyse the effect of early weight bearing versus late weight bearing on rehabilitation outcomes after ankle fractures, which primarily include ankle function scores, time to return to work/daily life and complication rates. METHODS: The China National Knowledge Infrastructure, Wanfang Data Knowledge Service Platform, China Science and Technology Journal, Web of Science, PubMed, Embase and Cochrane Library databases were searched. The focus was on identifying randomised controlled trials centred on early weight-bearing interventions for post-operative ankle fracture rehabilitation. All databases were searched for eligible studies published within the period from database inception to 20 June 2023. The eligible studies were screened according to the inclusion criteria. Study quality was evaluated using the methodology recommended by the Cochrane Handbook for the Systematic Evaluation of Interventions. Two authors independently performed the literature search and data extraction. Eligible studies were subjected to meta-analyses using Review Manager 5.3. Based on the time points at which post-operative ankle function was reported in the studies included in this paper, we decided to perform a meta-analysis of ankle function scores at 6 weeks post-operatively, 12 weeks post-operatively, 24-26 weeks post-operatively and 1 year post-operatively. RESULTS: A total of 11 papers, comprising 862 patients, were included. Meta-analysis indicated that patients receiving early weight-bearing interventions, which referred to weight-bearing for 6 weeks post-operatively, experienced enhancements in ankle function scores (Olerud-Molander score, AOFAS score or Baird-Jackson score) at various post-operative milestones: 6 weeks (SMD = 0.69, 95% CI: 0.49-0.88 and p < 0.01), 12 weeks (SMD = 0.57, 95% CI: 0.22-0.92 and p < 0.01) and the 24-26 weeks range (SMD = 0.52, 95% CI: 0.20-0.85 and p < 0.01). The results of subgroup analyses revealed that the effects of early weight-bearing interventions were influenced by ankle range-of-motion exercises. Additionally, early weight bearing allows patients to return to daily life and work earlier, which was evaluated by time when they resumed their preinjury activities (MD = -2.74, 95% CI: -3.46 to -2.02 and p < 0.01), with no distinct elevation in the incidence of complications (RR = 1.49, 95% CI: 0.85-2.61 and p > 0.05). CONCLUSION: The results showed that early weight bearing is effective in improving ankle function among post-operative ankle fracture patients and allows patients to return to daily life earlier. Significantly, the safety profile of early weight bearing remains favourable, with no higher risk of complications than late weight bearing.

PTH treatment before cyclic joint loading improves cartilage health and attenuates load-induced osteoarthritis development in mice.

Osteoarthritis (OA) treatment is limited by the lack of effective nonsurgical interventions to slow disease progression. Here, we examined the contributions of the subchondral bone properties to OA development. We used parathyroid hormone (PTH) to modulate bone mass before OA initiation and alendronate (ALN) to inhibit bone remodeling during OA progression. We examined the spatiotemporal progression of joint damage by combining histopathological and transcriptomic analyses across joint tissues. The additive effect of PTH pretreatment before OA initiation and ALN treatment during OA progression most effectively attenuated load-induced OA pathology. Individually, PTH directly improved cartilage health and slowed the development of cartilage damage, whereas ALN primarily attenuated subchondral bone changes associated with OA progression. Joint damage reflected early transcriptomic changes. With both treatments, the structural changes were associated with early modulation of immunoregulation and immunoresponse pathways that may contribute to disease mechanisms. Overall, our results demonstrate the potential of subchondral bone-modifying therapies to slow the progression of OA.

Weight-Bearing Physical Activity, Lower-Limb Muscle Mass, and Risk of Knee Osteoarthritis.

Importance: It has been demonstrated that total physical activity is not associated with risk of osteoarthritis. However, the association of different types of physical activity with incident knee osteoarthritis remains unclear. Objective: To determine whether weight-bearing recreational physical activities are associated with increased risk of incident knee osteoarthritis. Design, Setting, and Participants: This prospective cohort study used data from the Rotterdam Study (1996 to 2009), including participants with knee x-ray measurements at baseline and follow-up examinations. Participants with knee osteoarthritis at baseline were excluded. Residents aged 45 years and older of the Ommoord district in the city of Rotterdam in The Netherlands were invited to join the Rotterdam Study (78% response rate). Analysis was conducted in June 2023. Exposure: Total, weight-bearing, and non-weight-bearing recreational physical activities collected by questionnaires at baseline. Main Outcomes and Measures: Incident radiographic knee osteoarthritis measured by knee x-ray was the primary outcome, and incident symptomatic knee osteoarthritis defined by x-ray and knee pain questionnaire was the secondary outcome. The association of different types of recreational physical activity with radiographic knee osteoarthritis was examined using logistic regression within generalized estimating equation framework after adjusting for potential confounders. A prespecified stratification analysis was planned on the basis of lower-limb muscle mass index (LMI) tertiles, measured by dual-energy x-ray absorptiometry. Results: A total of 5003 individuals (2804 women [56.0%]; mean [SD] age, 64.5 [7.9] years) were included. The knee osteoarthritis incident rate was 8.4% (793 of 9483 knees) for a mean (SD) follow-up time of 6.33 (2.46) years. Higher weight-bearing activity was associated with increased odds of incident knee osteoarthritis (odds ratio [OR], 1.22; 95% CI, 1.10-1.35; P < .001), but non-weight-bearing activity was not (OR, 1.04; 95% CI, 0.95-1.15; P = .37). In the analysis stratified by LMI tertiles, the association of weight-bearing activity with incident osteoarthritis was found only among 431 patients in the lowest LMI tertile (OR, 1.53; 95% CI, 1.15-2.04; P = .003), but not among patients in the middle or high LMI tertile. Conclusions and Relevance: The findings of this study suggest that weight-bearing activity is associated with incident knee osteoarthritis in people with low levels of lower-limb muscle mass, which might be a promising avenue for tailored advice for physical activity.

Equivalent weight: Application of the assessment method on real task conducted by railway workers wearing a back support exoskeleton.

Commonly used risk indexes, such as the NIOSH Lifting Index, do not capture the effect of exoskeletons. This makes it difficult for Health and Safety professionals to rigorously assess the benefit of such devices. The community requires a simple method to assess the effectiveness of back-support exoskeleton's (BSE) in possibly reducing ergonomic risk. The method introduced in this work is termed "Equivalent Weight" (EqW) and it proposes an interpretation of the effect built on the benefit delivered through reduced activation of the erector spinae (ES). This manifests itself as an apparent reduction of the lifted load perceived by the wearer. This work presents a pilot study where a practical application of the EqW method is used to assess the ergonomic risk in manual material handling (MMH) when using a back support exoskeleton (StreamEXO). The results are assessed by combining observational measurements from on-site testing with five different workers and quantitative measures of the muscle activity reduction achieved during laboratory evaluation with ten workers. These results will show that when lifting, lowering, and carrying a 19 kg load the StreamEXO can reduce risk by up to two levels (from "high" to "low") in the target sub-tasks. The Lifting index (LI) was reduced up to 64% when examining specific sub-tasks and the worker's movement conduction.

The influence of the weight-bearing state on three-dimensional (3D) planning in lower extremity realignment - analysis of novel vs. state-of-the-art planning approaches.

BACKGROUND: The use of 3D planning to guide corrective osteotomies of the lower extremity is increasing in clinical practice. The use of computer-tomography (CT) data acquired in supine position neglects the weight-bearing (WB) state and the gold standard in 3D planning involves the manual adaption of the surgical plan after considering the WB state in long-leg radiographs (LLR). However, this process is subjective and dependent on the surgeons experience. A more standardized and automated method could reduce variability and decrease costs. PURPOSE: The aim of the study was (1) to compare three different three-dimensional (3D) planning modalities for medial open-wedge high tibial osteotomy (MOWHTO) and (2) to describe the current practice of adapting NWB CT data after considering the WB state in LLR. The purpose of this study is to validate a new, standardized approach to include the WB state into the 3D planning and to compare this method against the current gold standard of 3D planning. Our hypothesis is that the correction is comparable to the gold standard, but shows less variability due compared to the more subjective hybrid approach. METHODS: Three surgical planning modalities were retrospectively analyzed in 43 legs scheduled for MOWHTO between 2015 and 2019. The planning modalities included: (1) 3D hybrid (3D non-weight-bearing (NWB) CT models after manual adaption of the opening angle considering the WB state in LLR, (2) 3D NWB (3D NWB CT models) and (3) 3D WB (2D/3D registration of 3D NWB CT models onto LLR to simulate the WB state). The pre- and postoperative hip-knee-ankle angle (HKA) and the planned opening angle (°) were assessed and differences among modalities reported. The relationship between the reported differences and BMI, preoperative HKA (LLR), medial meniscus extrusion, Outerbridge osteoarthritis grade and joint line convergence angle (JLCA) was analyzed. RESULTS: The mean (std) planned opening angle of 3D hybrid did not differ between 3D hybrid and 3D WB (0.4 ± 2.1°) (n.s.) but was higher in 3D hybrid compared to 3D NWB (1.1° ± 1.1°) (p = 0.039). 3D WB demonstrated increased preoperative varus deformity compared to 3D NWB: 6.7 ± 3.8° vs. 5.6 ± 2.7° (p = 0.029). Patients with an increased varus deformity in 3D WB compared to 3D NWB (> 2 °) demonstrated more extensive varus alignment in LLR (p = 0.009) and a higher JLCA (p = 0.013). CONCLUSION: Small intermodal differences between the current practice of the reported 3D hybrid planning modality and a 3D WB approach using a 2D/3D registration algorithm were reported. In contrast, neglecting the WB state underestimates preoperative varus deformity and results in a smaller planned opening angle. This leads to potential under correction in MOWHTO, especially in patients with extensive varus deformities or JLCA. CLINICAL RELEVANCE: Incorporating the WB state in 3D planning modalities has the potential to increase accuracy and lead to a more consistent and reliable planning in MOWHTO. The inclusion of the WB state in automatized surgical planning algorithms has the potential to reduce costs and time in the future.

Adaptive gait responses to varying weight-bearing conditions: Inferences from gait dynamics and H-reflex magnitude.

This study investigates the effects of varying loading conditions on excitability in neural pathways and gait dynamics. We focussed on evaluating the magnitude of the Hoffman reflex (H-reflex), a neurophysiological measure representing the capability to activate motor neurons and the timing and placement of the foot during walking. We hypothesized that weight manipulation would alter H-reflex magnitude, footfall and lower body kinematics. Twenty healthy participants were recruited and subjected to various weight-loading conditions. The H-reflex, evoked by stimulating the tibial nerve, was assessed from the dominant leg during walking. Gait was evaluated under five conditions: body weight, 20% and 40% additional body weight, and 20% and 40% reduced body weight (via a harness). Participants walked barefoot on a treadmill under each condition, and the timing of electrical stimulation was set during the stance phase shortly after the heel strike. Results show that different weight-loading conditions significantly impact the timing and placement of the foot and gait stability. Weight reduction led to a 25% decrease in double limb support time and an 11% narrowing of step width, while weight addition resulted in an increase of 9% in step width compared to body weight condition. Furthermore, swing time variability was higher for both the extreme weight conditions, while the H-reflex reduced to about 45% between the extreme conditions. Finally, the H-reflex showed significant main effects on variability of both stance and swing phases, indicating that muscle-motor excitability might serve as feedback for enhanced regulation of gait dynamics under challenging conditions.

Poincaré analysis detects pathological limb loading rate variability in post-anterior cruciate ligament reconstruction individuals.

BACKGROUND: Post-ACLR individuals can experience repeated exposure to variable limb loading, which contributes to development of knee osteoarthritis. Variable limb loading can present as loading rate variability (LRV) and is magnified during tasks like fast walking when the system is stressed. Nonlinear measures that evaluate temporal variability have successfully detected changes in gait variability associated with altered motor control, however, appropriately describing and uncovering the nature of gait variability has been challenging. Here, Poincaré analysis, a nonlinear method unique in its ability to capture different aspects of variability, served to uncover and quantify changes in limb LRV. It was hypothesized that post-ACLR individuals' overloaded limbs would quantitatively and graphically demonstrate greater short-term stride-to-stride and long-term limb LRV during fast walking compared to the underloaded and healthy control limbs. METHODS: Fourteen post-ACLR individuals and fourteen healthy controls completed a walking protocol on an instrumented treadmill where they walked at 1.0 m/s and 1.5 m/s for 5-minutes each. A Welch's test was performed to compare differences in short-term and long-term LRV metrics for the post-ACLR individuals' overloaded and underloaded limbs and the healthy controls' right limbs. RESULTS: Analyses revealed that the post-ACLR individuals' overloaded limb exhibited significantly greater short-term and long-term values compared to the underloaded and healthy control limbs at 1.5 m/s (p<0.05). Additionally, the loading rate data was widely scattered across the plots for the overloaded limb, indicating greater LRV. SIGNIFICANCE: Poincaré analysis successfully identified that post-ACLR overloaded limbs exhibited impaired motor control during fast walking based on quantitative and graphical changes in variability. This highlights the clinical applications of Poincaré analysis, with the plots potentially serving as an easy-to-interpret diagnostic tool for pathological limb LRV.