Pigeon Pea Husk for Removal of Emerging Contaminants Trimethoprim and Atenolol from Water.

The pace of industrialization and rapid population growth in countries such as India entail an increased input of industrial and sanitary organic micropollutants, the so-called emerging contaminants (EC), into the environment. The emission of EC, such as pharmaceuticals, reaching Indian water bodies causes a detrimental effect on aquatic life and ultimately on human health. However, the financial burden of expanding sophisticated water treatment capacities renders complementary, cost-efficient alternatives, such as adsorption, attractive. Here we show the merits of washed and milled pigeon pea husk (PPH) as low-cost adsorbent for the removal of the EC trimethoprim (TMP) and atenolol (ATN) that are among the most detected pharmaceuticals in Indian waters. We found a linear increase in adsorption capacity of PPH for TMP and ATN at concentrations ranging from 10 to 200 µg/L and from 50 to 400 µg/L, respectively, reflecting the concentrations occurring in Indian water bodies. Investigation of adsorption kinetics using the external mass transfer model (EMTM) revealed that film diffusion resistance governed the adsorption process of TMP or ATN onto PPH. Moreover, analysis of the adsorption performance of PPH across an extensive range of pH and temperature illustrated that the highest adsorption loadings achieved concurred with actual conditions of Indian waters. We anticipate our work as starting point towards the development of a feasible adsorbent system aiming at low-cost water treatment.

Removal of carbamazepine, diclofenac and trimethoprim by solar driven advanced oxidation processes in a compound triangular collector based reactor: A comparison between homogeneous and heterogeneous processes.

Contaminants of emerging concern (including pharmaceuticals) are not effectively removed by municipal wastewater treatment plants (WWTPs), so particular concern is related to agricultural wastewater reuse due to their possible uptake in crops irrigated with WWTPs effluents. Advanced oxidation processes (AOPs) and solar AOPs have been demonstrated to effectively remove pharmaceuticals from different aqueous matrices. In this study, an heterogeneous photocatalytic process using powdered nitrogen-doped TiO2 immobilized on polystyrene spheres (sunlight/N-TiO2) was compared to the benchmark homogenous AOP sunlight/H2O2 in a compound triangular collector reactor, to evaluate the degradation of three pharmaceuticals (carbamazepine (CBZ), diclofenac (DCF), trimethoprim (TMP)) in water. The degradation of the contaminants by sunlight and sunlight-AOPs well fit the pseudo-first order kinetic model (but for TMP under sunlight). High removal efficiency by solar photolysis was observed for DCF (up to 100%, half-life sunlight cumulative energy QS,1/2 = 2 kJ L-1, half-life time t1/2 = 32 min), while CBZ (32%, QS,1/2 = 28 kJ L-1, t1/2 = 385 min) and TMP (5% removal after 300 min) removal was poor. The degradation rate of CBZ, TMP and DCF was found to be slower during sunlight/H2O2 (QS,1/2 = 5 kJ L-1, t1/2 = 77 min; QS,1/2 = 20 kJ L-1, t1/2 = 128 min; QS,1/2 = 4 kJ L-1, t1/2 = 27 min, respectively) compared to sunlight/N-TiO2 (QS,1/2 = 4 kJ L-1, t1/2 = 55 min; QS,1/2 = 3 kJ L-1, t1/2 = 42 min; QS,1/2 = 2 kJ L-1, t1/2 = 25 min, respectively). These results are promising in terms of solar technology upscale because the faster degradation kinetics observed for sunlight/N-TiO2 process would result in smaller treatment volume, thus possibly perspective compensating the cost of the photocatalyst.

Preparation of phenyl-boronic acid polymer monolith by initiator-free ring-opening polymerization for microextraction of sulfamethoxazole and trimethoprim from animal-originated foodstuffs.

Boronate affinity materials are usually used for selective enrichment of cis-diol-containing compounds, mainly based on formation of pH-dependent cyclic ester between cis-diol and boronic acid. Recently, B-N coordination, or combined with hydrogen-bonding interaction, was employed as primary interaction for the extraction of nitrogen-containing compounds. However, there are no reports about the combination of hydrophobic (or π-π) interaction and B-N coordination for the extraction. Here, we prepared a novel hydrophobic phenyl-boronic acid polymer (PBAP) through initiator-free ring-opening polymerization. The adsorption experiment indicated that the PBAP could combine hydrophobic (or π-π) interaction and B-N coordination to enhance their adsorption capacity toward hydrophobic and nitrogen-containing compounds, for example sulfamethoxazole (SMX) and trimethoprim (TMP). In addition, the PBAP monolith synthesized in pipette tip was used as solid phase microextraction (SPME) sorbent with combination of ultra high performance liquid chromatography to extract and monitor SMX and TMP from animal-originated foodstuffs. The proposed method exhibited low limit of quantitation as 5.0 and 1.0 ng mL-1 for SMX and TMP, respectively. The recoveries at three spiked levels were between 92.4% to 100.5% for SMX, and 92.7% to 102.6% for TMP, with intra-day and inter-day relative standard deviations no more than 5.3% and 8.6%, respectively. These results well demonstrated that the combination of hydrophobic (or π-π) interaction and B-N coordination played an important role in the extraction of hydrophobic and nitrogen-containing compounds.

Tolerance intervals modeling for design space of a salt assisted liquid-liquid microextraction of trimethoprim and six common sulfonamide antibiotics in environmental water samples.

Sulfonamides and trimethoprim combinations have been used extensively as antimicrobial agents for prevention and treatment of human and animal infections. Although many microextraction methods were developed for monitoring their residues in environmental water, none of these methods applied liquid-liquid microextraction for this purpose. This work presents for the first time a simultaneous Salt Assisted Liquid-Liquid Microextraction SALLME coupled with HPLC-UV for determination of trimethoprim and six common sulfonamide residues (sulfathiazole, sulfadiazine, sulfadmidine, sulfamethoxazole sulfadoxine and sulfaquinoxaline) in water samples. Co-extraction of trimethoprim with sulfonamides was achieved by the addition of perchloric acid as a chaotropic agent to the extraction medium. Quality by Design framework was applied to develop and optimize both of SALLME and HPLC steps to ensure procedure robustness and sensitivity. Tolerance interval modeling of SALLME responses was applied to construct the design space of SALLME procedure. The optimized HPLC system enabled fast, sensitive and robust separation the extracted compounds within four minutes. The method detection limits of the method were in the range of 2.15-7.64 ng.mL-1. These values were far below the guidelines recommended limits (35 and 70 ng.mL-1 for each individual sulfonamide and trimethoprim respectively).

Synthesis of monodisperse molecularly imprinted microspheres with multi-recognition ability via precipitation polymerization for the selective extraction of cyromazine, melamine, triamterene and trimethoprim.

Through precipitation polymerization, three monodisperse molecularly imprinted polymers (MIPs) containing imprints of 2,4-diamino-6-methyl-1,3,5-triazine (DM), cyromazine (CY) or trimethoprim (TM), were synthesized using methacrylic acid as functional monomer, divinylbenzene as cross-linker, and a mixture of acetonitrile-toluene (90/10, v/v) as porogen. The morphology and selectivity of the MIPs were characterized and compared systematically. The MIPs had the best specific binding in pure acetonitrile, and the data of adsorption experiment were fitted well with Langmuir and Freundlich model. In addition, DM-MIPs showed the excellent binding and multi-recognition capability for CY, melamine (ME), triamterene (TA) and TM, and the binding capacity were 7.18, 7.56, 5.66 and 5.45µmol/g, respectively. Due to the pseudo template and the ability of multi-recognition, DM-MIPs as sorbent material could avoid the effect of template leakage on quantitative analysis. Therefore, DM-MIPs were used as a solid-phase extraction material to enrich ME, CY, TA and TM from different bio-matrix samples for high performance liquid chromatography analysis. Under the optimized conditions, the recoveries of three spiked levels in different bio-matrix samples were ranged from 80.9% to 91.5% with RSD≤4.2 (n=3).

Pathogens and pharmaceuticals in source-separated urine in eThekwini, South Africa.

In eThekwini, South Africa, the production of agricultural fertilizers from human urine collected from urine-diverting dry toilets is being evaluated at a municipality scale as a way to help finance a decentralized, dry sanitation system. The present study aimed to assess a range of human and environmental health hazards in source-separated urine, which was presumed to be contaminated with feces, by evaluating the presence of human pathogens, pharmaceuticals, and an antibiotic resistance gene. Composite urine samples from households enrolled in a urine collection trial were obtained from urine storage tanks installed in three regions of eThekwini. Polymerase chain reaction (PCR) assays targeted 9 viral and 10 bacterial human pathogens transmitted by the fecal-oral route. The most frequently detected viral pathogens were JC polyomavirus, rotavirus, and human adenovirus in 100%, 34% and 31% of samples, respectively. Aeromonas spp. and Shigella spp. were frequently detected gram negative bacteria, in 94% and 61% of samples, respectively. The gram positive bacterium, Clostridium perfringens, which is known to survive for extended times in urine, was found in 72% of samples. A screening of 41 trace organic compounds in the urine facilitated selection of 12 priority pharmaceuticals for further evaluation. The antibiotics sulfamethoxazole and trimethoprim, which are frequently prescribed as prophylaxis for HIV-positive patients, were detected in 95% and 85% of samples, reaching maximum concentrations of 6800 µg/L and 1280 µg/L, respectively. The antiretroviral drug emtricitabine was also detected in 40% of urine samples. A sulfonamide antibiotic resistance gene (sul1) was detected in 100% of urine samples. By coupling analysis of pathogens and pharmaceuticals in geographically dispersed samples in eThekwini, this study reveals a range of human and environmental health hazards in urine intended for fertilizer production. Collection of urine offers the benefit of sequestering contaminants from environmental release and allows for targeted treatment of potential health hazards prior to agricultural application. The efficacy of pathogen and pharmaceutical inactivation, transformation or removal during urine nutrient recovery processes is thus briefly reviewed.

Analysis of trimethoprim, lincomycin, sulfadoxin and tylosin in swine manure using laser diode thermal desorption-atmospheric pressure chemical ionization-tandem mass spectrometry.

A new extraction method coupled to a high throughput sample analysis technique was developed for the determination of four veterinary antibiotics. The analytes belong to different groups of antibiotics such as chemotherapeutics, sulfonamides, lincosamides and macrolides. Trimethoprim (TMP), sulfadoxin (SFX), lincomycin (LCM) and tylosin (TYL) were extracted from lyophilized manure using a sonication extraction. McIlvaine buffer and methanol (MeOH) were used as extraction buffers, followed by cation-exchange solid phase extraction (SPE) for clean-up. Analysis was performed by laser diode thermal desorption-atmospheric pressure chemical-ionization (LDTD-APCI) tandem mass spectrometry (MS/MS) with selected reaction monitoring (SRM) detection. The LDTD is a high throughput sample introduction method that reduces total analysis time to less than 15s per sample, compared to minutes when using traditional liquid chromatography (LC). Various SPE parameters were optimized after sample extraction: the stationary phase, the extraction solvent composition, the quantity of sample extracted and sample pH. LDTD parameters were also optimized: solvent deposition, carrier gas, laser power and corona discharge. The method limit of detection (MLD) ranged from 2.5 to 8.3 µg kg(-1) while the method limit of quantification (MLQ) ranged from 8.3 to 28µgkg(-1). Calibration curves in the manure matrix showed good linearity (R(2)≥ 0.996) for all analytes and the interday and intraday coefficients of variation were below 14%. Recoveries of analytes from manure ranged from 53% to 69%. The method was successfully applied to real manure samples.

Desorption kinetics of sulfonamide and trimethoprim antibiotics in soils assessed with diffusive gradients in thin-films.

Although sorption/desorption of antibiotics in soils affects their mobility and availability, with consequences for risks to the surrounding environment, the dynamics of these processes are not well-known. In this study, diffusive gradients in thin-films devices suitable for measuring polar organic compounds (o-DGT) were deployed in two soils for a range of times (5 h to 20 d) to measure the distribution and rates of exchange between solid phase and solution of three sulphonamides (SAs; sulfamethoxazole, SMX; sulfamethazine, SMZ; and sulfadimethoxine, SDM) and trimethoprim (TMP). o-DGT continuously removes antibiotics to a XAD gel layer after passage through a well-defined diffusion layer and therefore perturbs their concentration in the adjacent soil solution. This induces a remobilization flux from the solid phase, which is related to the concentration of antibiotics in the soil solution, their diffusional supply, and the exchange kinetics between dissolved and sorbed antibiotics. A dynamic model of solute interactions called DIFS (DGT induced fluxes in soils) was used to derive distribution coefficients for labile antibiotics (Kdl) and the rate constant for supply of antibiotics from solid phase to solution, expressed as a response time (Tc). Larger labile solid phase pools were observed for TMP than for SAs. The soils could resupply TMP so rapidly that in one soil, where Tc = 2 min, supply was controlled by diffusion. Response times for SAs were generally longer (>27 min), particularly for SDM (>3 h), implying that the supply of SAs to o-DGT samplers was limited by the desorption release rate. A wider implication of this study is that similar solid phase release kinetics may control the uptake of antibiotics by biota.

MIP-graphene-modified glassy carbon electrode for the determination of trimethoprim.

A novel sensitive electrochemical sensor was developed by electropolymerization of pyrrole (PY) and molecularly imprinted polymer (MIP) which was synthesized onto a glassy carbon electrode (GCE) in aqueous solution using cyclic voltammetry in the presence of Trimethoprim (TMP) as template molecules. Furthermore, a previous electrode modification was performed by deposition of a suspension of graphene on the electrode's surface. The performance of the imprinted and non-imprinted (NIP) films was evaluated by impedance spectroscopy (EIS) and cyclic voltammetry (CV) of a ferric solution. The molecularly imprinted film exhibited a high selectivity and sensitivity toward TMP. The sensor presented a linear range, between peak current intensity and logarithm of TMP concentration between 1.0 × 10(-6) and 1.0 × 10(-4)M. The results were accurate (with recoveries higher than 94%), precise (with standard deviations less than 5%) and the detection limit was 1.3 × 10(-7)M. The new sensor is selective, simple to construct and easy to operate. The MIP sensor was successfully applied to quantify TMP in urine samples.

Removal of trace organic chemical contaminants by a membrane bioreactor.

Emerging wastewater treatment processes such as membrane bioreactors (MBRs) have attracted a significant amount of interest internationally due to their ability to produce high quality effluent suitable for water recycling. It is therefore important that their efficiency in removing hazardous trace organic contaminants be assessed. Accordingly, this study investigated the removal of trace organic chemical contaminants through a full-scale, package MBR in New South Wales, Australia. This study was unique in the context of MBR research because it characterised the removal of 48 trace organic chemical contaminants, which included steroidal hormones, xenoestrogens, pesticides, caffeine, pharmaceuticals and personal care products (PPCPs). Results showed that the removal of most trace organic chemical contaminants through the MBR was high (above 90%). However, amitriptyline, carbamazepine, diazepam, diclofenac, fluoxetine, gemfibrozil, omeprazole, sulphamethoxazole and trimethoprim were only partially removed through the MBR with the removal efficiencies of 24-68%. These are potential indicators for assessing MBR performance as these chemicals are usually sensitive to changes in the treatment systems. The trace organic chemical contaminants detected in the MBR permeate were 1 to 6 orders of magnitude lower than guideline values reported in the Australian Guidelines for Water Recycling. The outcomes of this study enhanced our understanding of the levels and removal of trace organic contaminants by MBRs.

Development of a liquid chromatography­tandem mass spectrometry method for the determination of sulfonamides, trimethoprim and dapsone in honey and validation according to Commission Decision 2002/657/EC for banned compounds [corrected].

This work reports a sensitive liquid chromatography-tandem mass spectrometry (LC-MS/MS) method for identification and quantification of seven sulfonamides, trimethoprim and dapsone in honey. The method is based on a solid-phase extraction (SPE) step of the target analytes with Oasis HLB cartridges after acidic hydrolysis of the honey sample to liberate the sugar-bound sulfonamides. Analysis was performed using liquid chromatography-tandem mass spectrometry (LC-MS/MS) in the positive electro-spray ionization (ESI) mode with two different isotopically labeled internal standards with the view to improve the quantitative performance of the method. The method validation has been performed according to the Commission Decision 2002/657/EC; the average recoveries, measured at three concentration levels (1.5, 2.5 and 5.0 µg kg(-1)), have been estimated in the range 70 to 106% while the respective % relative standard deviations of the within-laboratory reproducibility ranged from 6 to 18%. Mean values of the expanded uncertainties calculated were in the range 22-41% at the 99% confidence level. Decision limit (CCα) and detection capability (CCß) values were in the ranges 0.4-0.9 and 0.7-1.4 µg kg(-1), respectively. Matrix effects have been investigated demonstrating a moderate signal suppression/enhancement for most of the target compounds. The method described has been successfully applied to the analysis of honey samples; sulfamethoxazole, sulfathiazole and trimethoprim were detected in some cases.

Behavior of pharmaceuticals in waste water treatment plant in Japan.

The fate of pharmaceuticals in a wastewater treatment plant (WWTP) in Kumamoto, Japan with activated sludge treatment is reported. Selected pharmaceuticals were detected in influent. Results from the present study confirmed that Acetaminophen, Amoxicillin, Ampicillin and Famotidine were removed at a high rate (>90% efficiency). In contrast, removal efficiency of Ketoprofen, Losartan, Oseltamivir, Carbamazepine, and Diclofenac was relatively low (<50%). The selected pharmaceuticals were also detected in raw sludge. In digestive process, Indomethacin, Atenolol, Famotidine, Trimethoprim and Cyclofosamide were removed at a high (>70% efficiency). On the other hand, removal of Carbamazepine, Ketoprofen and Diclofenac was not efficient (<50%).

Derivative spectrum chromatographic method for the determination of trimethoprim in honey samples using an on-line solid-phase extraction technique.

A simple, selective and rapid analytical method for determination of trimethoprim (TMP) in honey samples was developed and validated. This method is based on a SPE technique followed by HPLC with photodiode array detection. After dilution and filtration, aliquots of 500 µL honey samples were directly injected to an on-line SPE HPLC system. TMP was extracted on an RP SPE column, and separated on a hydrophilic interaction chromatography column during HPLC analysis. At the first detection step, the noise level of the photodiode array data was reduced with two-dimensional equalizer filtering, and then the smoothed data were subjected to derivative spectrum chromatography. On the second-derivative chromatogram at 254 nm, the limit of detection and the limit of quantification of TMP in a honey sample were 5 and 10 ng/g, respectively. The proposed method showed high accuracy (60-103%) with adequate sensitivity for TMP monitoring in honey samples.

The application of membrane bioreactors as decentralised systems for removal of endocrine disrupting chemicals and pharmaceuticals.

The concentrations of some important endocrine disrupting chemicals and pharmaceuticals after various stages of wastewater treatment were investigated. The endocrine disrupting chemicals included natural and synthetic estrogenic and androgenic steroids. The pharmaceuticals included a series of sulfonamide antibiotics and trimethoprim. The removal efficiency of a membrane bioreactor (MBR) was investigated and compared with a conventional activated sludge (CAS) system. Samples were analysed by liquid chromatography tandem mass spectrometry. Results showed that the MBR and CAS systems effectively removed steroidal estrogens and androgens, but only partially eliminated the target antibiotics from wastewater. The MBR was shown to be more effective than the CAS system which was possibly attributed to the high solid retention time and concentration of biosolids in the MBR. The results highlight the potential wider application of MBRs for the removal of trace chemical contaminants in wastewater and their potential for use as decentralised wastewater treatment systems.

A multidimensional high performance liquid chromatography method coupled with amperometric detection using a boron-doped diamond electrode for the simultaneous determination of sulfamethoxazole and trimethoprim in bovine milk.

The development and validation of a multidimensional HPLC method using an on-line clean-up column coupled with amperometric detection employing a boron-doped diamond (BDD) electrode for the simultaneous determination of sulfamethoxazole (SMX) and trimethoprim (TMP) in bovine milk are presented. Aliquots of pre-prepared skim-milk samples were directly injected into a RAM octyl-BSA column in order to remove proteins that otherwise would interfere with milk analysis. After exclusion of the milk proteins, SMX and TMP were transferred to the analytical column (an octyl column) and the separation of the compounds from one another and from other endogenous milk components was achieved. SMX and TMP were detected amperometrically at 1.25V vs. Ag/AgCl (3.0molL(-1) KCl). Results with good linearity in the concentration ranges 50-800 and 25-400microgL(-1) for SMX and TMP, respectively, were obtained and no fouling of the BDD electrode was observed within the experimental period of several hours. The intra- and inter-assay coefficients of variation were less than 10% for both drugs and the obtained LOD values for SMX and TMP were 25.0 and 15.0microgL(-1), respectively.

A confirmatory method for the simultaneous extraction, separation, identification and quantification of Tetracycline, Sulphonamide, Trimethoprim and Dapsone residues in muscle by ultra-high-performance liquid chromatography-tandem mass spectrometry according to Commission Decision 2002/657/EC.

A rapid confirmatory multi-residue method for the analysis of tetracyclines, sulphonamides, trimethoprim and dapsone by UPLC-MS/MS is described. The method is able to quantify and confirm the following 19 compounds, oxytetracycline, tetracycline, chlortetracycline, doxycycline, sulfadiazine, sulfathiazole, sulfapyridine, trimethoprim, sulfamerazine, sulfamethizole, sulfamethazine, sulfamethoxypyridazine, sulfamonomethoxine, sulfachlorpyridazine, dapsone, sulfamethoxazole, sulfisoxazole, sulfaquinoxaline and sulfadimethoxine. Samples are extracted with 0.1M EDTA and acetonitrile, which is then evaporated under a stream of nitrogen and reconstituted in water. Following centrifugation and filtering, an aliquot is analysed by UPLC-MS/MS using positive electrospray ionisation and multiple reaction monitoring. The method is deemed rapid as all analytes are extracted by a single extraction technique, with no solid-phase extraction clean up required. Validation is according to Commission Decision 2002/657/EC and was carried out for bovine, porcine, ovine and poultry species. Specificity, recovery, repeatability, reproducibility, CCalpha and CCbeta data is presented.

Preparation of alumina-coated magnetite nanoparticle for extraction of trimethoprim from environmental water samples based on mixed hemimicelles solid-phase extraction.

In this study, a new type of alumina-coated magnetite nanoparticles (Fe(3)O(4)/Al(2)O(3) NPs) modified by the surfactant sodium dodecyl sulfate (SDS) has been successfully synthesized and applied for extraction of trimethoprim (TMP) from environmental water samples based on mixed hemimicelles solid-phase extraction (MHSPE). The coating of alumina on Fe(3)O(4) NPs not only avoids the dissolving of Fe(3)O(4) NPs in acidic solution, but also extends their application without sacrificing their unique magnetization characteristics. Due to the high surface area of these new sorbents and the excellent adsorption capacity after surface modification by SDS, satisfactory concentration factor and extraction recoveries can be produced with only 0.1g Fe(3)O(4)/Al(2)O(3) NPs. Main factors affecting the adsolubilization of TMP such as the amount of SDS, pH value, standing time, desorption solvent and maximal extraction volume were optimized. Under the selected conditions, TMP could be quantitatively extracted. The recoveries of TMP by analyzing the four spiked water samples were between 67 and 86%, and the relative standard deviation (RSD) ranged from 2 to 6%. Detection and quantification limits of the proposed method were 0.09 and 0.24 microg L(-1), respectively. Concentration factor of 1000 was achieved using this method to extract 500 mL of different environmental water samples. Compared with conventional SPE methods, the advantages of this new Fe(3)O(4)/Al(2)O(3) NPs MHSPE method still include easy preparation and regeneration of sorbents, short times of sample pretreatment, high extraction yields, and high breakthrough volumes. It shows great analytical potential in preconcentration of organic compounds from large volume water samples.

Analysis of substances to be used as internal standards in MEKC.

The use of internal standards (ISs) improves the quantitative performance of CE. However, ISs chosen for use in CZE often cannot be used for micellar EKC (MEKC). Therefore 22 substances were investigated as potential ISs in MEKC. These substances were selected based upon a literature search. The substances were investigated using a method similar to the standard operating conditions for MEKC as recommended by S. Terabe. Furthermore, the migration time and the corrected migration time (k(S)) were determined for each substance to establish the migration position relative to other peaks in the electropherograms. A combination of eight substances, selected according to the obtained results (t(m) = 4 up to 12 min), was tested for practical benefit and applicability. The peak area precision was in the range of 0.8 and 1.2% (n = 60), and the peaks were well shaped for all the investigated substances. The selected substances covered a wide migration time window and therefore they can be regarded as suitable for future analysis at any required migration position.

A systematic investigation of recovery in preparative reverse phase high performance liquid chromatography/mass spectrometry.

In this paper we report a systematic recovery study based on reversed phase high performance liquid chromatography (RP-HPLC) separation and mass spectrometric (MS) based fractionation. Factors including a compound's physicochemical properties, column mass loading and presence of impurities were investigated through commercially available compounds. Results suggest that the delay time between MS peak detection and fraction collection, fraction detector's signal-to-noise ratio and compound's base peak width in the chromatogram have the biggest impacts on purification recovery. In an effort to assess sample recovery within our high throughput purification process, re-purification was performed on four compound libraries that were synthesized in-house. Reproducible recoveries (>80%) were achieved in all tests.

Removal of selected non-steroidal anti-inflammatory drugs (NSAIDs), gemfibrozil, carbamazepine, beta-blockers, trimethoprim and triclosan in conventional wastewater treatment plants in five EU countries and their discharge to the aquatic environment.

The removal of commonly used pharmaceuticals (ibuprofen, naproxen, diclofenac, gemfibrozil, carbamazepine, atenolol, metoprolol and trimethoprim) and a biocide (triclosan) in operating wastewater treatment plants in five EU countries has been studied. Under normal operating conditions the acidic drugs and triclosan were partially removed with removal rates varying from ca. 20 to >95%. The highest removal rate was found for ibuprofen and triclosan (>90%) followed by naproxen (80%), gemfibrozil (55%) and diclofenac (39%). Ibuprofen undergoes an oxidative transformation to corresponding hydroxy- and carboxy-metabolites, which contributes to its high removal rate. Disturbances in the activated sludge process resulted in lower removal rates for all acidic drugs, mostly for diclofenac (<10% removed) but also for ibuprofen (<60% removed). The treatment of wastewaters by activated sludge usually did not result in any practical removal (<10%) of neutral carbamazepine or basic atenolol, metoprolol and trimethoprim. The removal rates of the investigated drugs and triclosan are discussed in terms of mechanisms responsible for their removal. Discharges of carbamazepine, diclofenac, gemfibrozil, naproxen, triclosan and trimethoprim from WWTPs to the aquatic environment, expressed as the average concentration in the effluent and the daily discharged quantity per person served by WWTPs were assessed.