Enhancing environmental performance in biogas production from wastewater-grown microalgae: A life cycle assessment perspective.

The production of biogas from microalgae has gained attention due to their rapid growth, CO2 sequestration, and minimal land use. This study uses life cycle assessment to assess the environmental impacts of biogas production from wastewater-grown microalgae through anaerobic digestion within an optimized microalgae-based system. Using SimaPro® 9 software, 3 scenarios were modeled considering the ReCiPe v1.13 midpoint and endpoint methods for environmental impact assessment in different categories. In the baseline scenario (S1), a hypothetical system for biogas production was considered, consisting of a high rate algal pond (HRAP), a settling, an anaerobic digester, and a biogas upgrading unit. The second scenario (S2) included strategies to enhance biogas yield, namely co-digestion and thermal pre-treatment. The third scenario (S3), besides considering the strategies of S2, proposed the biogas upgrading in the HRAP and the digestate recovery as a biofertilizer. After normalization, human carcinogenic toxicity was the most positively affected category due to water use in the cultivation step, accounted as avoided product. However, this category was also the most negatively affected by the impacts of the digester heating energy. Anaerobic digestion was the most impactful step, constituting on average 60.37% of total impacts. Scenario S3 performed better environmentally, primarily due to the integration of biogas upgrading within the cultivation reactor and digestate use as a biofertilizer. Sensitivity analysis highlighted methane yield's importance, showing potential for an 11.28% reduction in ionizing radiation impacts with a 10% increase. Comparing S3 biogas with natural gas, the resource scarcity impact was reduced sixfold, but the human health impact was 23 times higher in S3.

Wastewater-grown microalgae biomass as a source of sustainable aviation fuel: Life cycle assessment comparing hydrothermal routes.

The present paper compared, through life cycle assessment (LCA), the production of aviation biofuel from two hydrothermal routes of microalgae cultivated in wastewater. Hydrothermal liquefaction (HTL) and gasification followed by Fischer-Tropsch synthesis (G + FT) were compared. Both routes included biomass production, hydrotreatment for biofuel upgrading, and product fractionation. Secondary data obtained from the literature were used for the cradle-to-gate LCA. G + FT had a higher impact than HTL in the 18 impact categories assessed, with human carcinogenic toxicity exerting the most harmful pressure on the environment. The catalysts were the inputs that caused the most adverse emissions. The solvent used for bio-oil separation also stood out in terms of impacts. In HTL, emissions for global warming were -51.6 g CO2 eq/MJ, while in G + FT, they were 250 g CO2 eq/MJ. At the Endpoint level, HTL resulted in benefits to human health and ecosystems, while G + FT caused environmental damage in these two categories, as well as in the resources category. In the improvement scenarios, besides considering solid, aqueous, and gaseous products as co-products rather than just as waste/emissions, a 20% reduction in catalyst consumption and 90% recovery were applied. Thus, in HTL, 39.47 kg CO2 eq was avoided, compared to 35.44 kg CO2 eq in the base scenario. In G + FT, emissions decreased from 147.55 kg CO2 eq to the capture of 8.60 kg CO2 eq.

Assessment of characteristics and treatment processes of wastewater from slaughterhouses in the state of Minas Gerais, Brazil.

The state of Minas Gerais is one of Brazil's largest animal protein producers, and its slaughterhouses generate highly polluting wastewater, which needs to be treated for discharge or reuse. As a novelty, this review article focused on assessing the characteristics and methods to treat wastewater from slaughterhouses in the state of Minas Gerais, and verifying its compliance with environmental regulatory agencies. The aim was to present data that helps to better manage this residue in other Brazilian states and countries. By analyzing the literature data, it was found that raw slaughterhouse wastewater (SWW) showed a high concentration of organic matter. For most SWW, the BOD5/COD ratio was above 0.4, which implies that it can be treated biologically. Generally, treated wastewater was in accordance with legal discharge standards, considering COD and BOD5 removals above 70% and 75%, respectively. It was found that wastewater treatment plants (WWTPs) consisted of some type of pretreatment (screens, grease traps) to remove coarse solids and fatty material, eventually followed by a flotation step and finally by biological processes, mostly anaerobic and/or aerated (or facultative) ponds. However, the absence of an aerobic process at the end of the treatment in some WWTPs, in addition to a system allowing better removal of biological flocs, might be the reason for ammoniacal nitrogen and suspended solids values being above the allowed maximum in treated wastewater, respectively. Besides the discharge into water bodies, it was verified that fertigation using treated SWW is very common in the state of Minas Gerais.

Enhancing microalgae biomass production: Exploring improved scraping frequency in a hybrid cultivation system.

Recently, hybrid systems, such as those incorporating high-rate algal ponds (HRAPs) and biofilm reactors (BRs), have shown promise in treating domestic wastewater while cultivating microalgae. In this context, the objective of the present study was to determine an improved scraping frequency to maximize microalgae biomass productivity in a mix of industrial (fruit-based juice production) and domestic wastewater. The mix was set to balance the carbon/nitrogen ratio. The scraping strategy involved maintaining 1 cm wide stripes to retain an inoculum in the reactor. Three scraping frequencies (2, 4, and 6 days) were evaluated. The findings indicate that a scraping frequency of each 2 days provided the highest biomass productivity (18.75 g total volatile solids m-2 d-1). The species' behavior varied with frequency: Chlorella vulgaris was abundant at 6-day intervals, whereas Tetradesmus obliquus favored shorter intervals. Biomass from more frequent scraping demonstrated a higher lipid content (15.45%). Extrapolymeric substance production was also highest at the 2-day frequency. Concerning wastewater treatment, the system removed 93% of dissolved organic carbon and ∼100% of ammoniacal nitrogen. Combining industrial and domestic wastewater sources to balance the carbon/nitrogen ratio enhanced treatment efficiency and biomass yield. This study highlights the potential of adjusting scraping frequencies in hybrid systems for improved wastewater treatment and microalgae production.

Biocompounds from wastewater-grown microalgae: a review of emerging cultivation and harvesting technologies.

Microalgae biomass has attracted attention as a feedstock to produce biofuels, biofertilizers, and pigments. However, the high production cost associated with cultivation and separation stages is a challenge for the microalgae biotechnology application on a large scale. A promising approach to overcome the technical-economic limitations of microalgae production is using wastewater as a nutrient and water source for cultivation. This strategy reduces cultivation costs and contributes to valorizing sanitation resources. Therefore, this article presents a comprehensive literature review on the status of microalgae biomass cultivation in wastewater, focusing on production strategies and the accumulation of valuable compounds such as lipids, carbohydrates, proteins, fatty acids, and pigments. This review also covers emerging techniques for harvesting microalgae biomass cultivated in wastewater, discussing the advantages and limitations of the process, as well as pointing out the main research opportunities. The novelty of the study lies in providing a detailed analysis of state-of-the-art and potential advances in the cultivation and harvesting of microalgae, with a special focus on the use of wastewater and implementing innovative strategies to enhance productivity and the accumulation of compounds. In this context, the work aims to guide future research concerning emerging technologies in the field, emphasizing the importance of innovative approaches in cultivating and harvesting microalgae for advancing knowledge and practical applications in this area.

COVID-19 cases, vaccination, and SARS-CoV-2 in wastewater: insights from a Brazilian municipality.

Vaccines combatting COVID-19 demonstrate the ability to protect against disease and hospitalization, and reduce the likelihood of death caused by SARS-CoV-2. In addition, monitoring viral loads in sewage emerges as another crucial strategy in the epidemiological context, enabling early and collective detection of outbreaks. The study aimed to monitor the viral concentration of SARS-CoV-2 in untreated sewage in a Brazilian municipality. Also, it attempted to correlate these measurements with the number of clinical cases and deaths resulting from COVID-19 between July 2021 and July 2022. SARS-CoV-2 viral RNA was quantified by RT-qPCR. Pearson's correlation was performed to analyze the variables' relationship using the number of cases, deaths, vaccinated individuals, and viral concentration of SARS-CoV-2. The results revealed a significant negative correlation (p < 0.05) between the number of vaccinated individuals and the viral concentration of SARS-CoV-2, suggesting that after vaccination, the RNA viral load concentration was reduced in the sample population by the circulating concentration of wastewater. Consequently, wastewater monitoring, in addition to functioning as an early warning system for the circulation of SARS-CoV-2 and other pathogens, can offer a novel perspective that enhances decision-making, strengthens vaccination campaigns, and contributes to authorities establishing systematic networks for monitoring SARS-CoV-2.

Microalgae biomass as a conditioner and regulator of soil quality and fertility.

Characteristics of an acid soil cultivated with Urochloa brizantha cv. Marandu were evaluated in relation to two types of fertilization: a conventional one, chemical based on nitrogen and potassium, and a biofertilizer, based on microalgae biomass. The results were compared among three treatments, control, conventional, and biological fertilization, with seven replications each. The study evaluated microalgae community, total carbon and nitrogen contents, mineral nitrogen, and enzymatic activity. Chlorella vulgaris showed the highest organism density, which can be explained by its rapid growth and high resistance. The highest species diversity was detected in the control 1,380,938 org cm-3 and biological 1,841,250 org cm-3 treatments, with the latter showing a higher density of cyanobacteria, especially Pseudanabaena limnetica with 394,554 org cm-3. The soil treated with chemical fertilization showed higher nitrate (9.14 mg NKg-1 NO3--N) and potassium (52.32 mg dm-3) contents. The highest levels of sulfur (21.73 mg dm-3) and iron (96.46 mgdm-3) were detected in the biological treatment. The chemical treatment showed higher activity of the enzymes acid phosphatase, acetylglucosaminidase, and sulfatase, while α-glucosidase and leucine aminopeptidase stood out in the biological treatment. Soil properties were not significantly affected by the treatments. The use of microalgae biomass derived from wastewater treatment from milking parlors was evaluated and presented as a promising biofertilizer for agriculture, following the line of recovering nutrient-rich wastes. In this sense, although many challenges need to be overcome, the results suggest that microalgal-based fertilizers could lead to low-impact agriculture.

Copper multifaceted interferences during swine wastewater treatment in high-rate algal ponds: alterations on nutrient removal, biomass composition and resource recovery.

Microalgae cultivation in swine wastewater (SW) allows the removal of nutrients and biomass production. However, SW is known for its Cu contamination, and its effects on algae cultivation systems such as high-rate algal ponds (HRAPs) are poorly understood. This gap in the literature limits the proposition of adequate concentrations of Cu to optimise SW treatment and resource recovery in HRAPs. For this assessment, 12 HRAPs installed outdoors were operated with 800 L of SW with different Cu concentrations (0.1-4.0 mg/L). Cu's interferences on the growth and composition of biomass and nutrient removal from SW were investigated through mass balance and experimental modelling. The results showed that the concentration of 1.0 mg Cu/L stimulated microalgae growth, and above 3.0 mg Cu/L caused inhibition accompanied by an accumulation of H2O2. Furthermore, Cu affected the contents of lipids and carotenoids observed in the biomass; the highest concentration was observed in the control (16%) and 0.5 mg Cu/L (1.6 mg/g), respectively. An innovative result was verified for nutrient removal, in which increased Cu concentration reduced the N-NH4+ removal rate. In contrast, the soluble P removal rate was enhanced by 2.0 mg Cu/L. Removal of soluble Cu in treated SW reached 91%. However, the action of microalgae in this process was not associated with assimilation but with a pH increase resulting from photosynthesis. A preliminary evaluation of economic viability showed that the commercialisation of biomass considering the concentration of carotenoids obtained in HRAPs with 0.5 mg Cu/L could be economically attractive. In conclusion, Cu affected the different parameters evaluated in this study in a complex way. This can help managers consort nutrient removal, biomass production, and resource recovery, providing information for possible industrial exploitation of the generated bioproducts.

Microbial dynamics and methanogenic potential of co-digestion of sugarcane vinasse and dairy secondary effluent in an upflow anaerobic sludge blanket reactor.

Co-digestion is a strategy that may prevent microbial inhibition during the anaerobic treatment of sugarcane vinasse, a substrate with highly biodegradable organic load, acidity, and toxic compound levels (e.g., sulfates, phenols). In this context, this study evaluated the microbial dynamics and methanogenic potential throughout the co-digestion of sugarcane vinasse and secondary effluent from the dairy industry in a mesophilic lab-scale upflow anaerobic sludge blanket (UASB) reactor. Periodic next-generation sequencing (NGS) analyses revealed an increase in the relative abundance of the phylum Euryarchaeota (+8.6 % after inoculation), predominating hydrogenotrophic methanogens (Methanobacterium and Methanobrevibacter) at the end of the operation. Moreover, the average methane yield was 221 mLCH4 gCODrem-1, with 69 % of organic matter removal. These results evidenced a progressive acclimation of the anaerobic microbial community to the substrate and a stable operation. Therefore, the proposed experiment demonstrates energy advantages for the agro-industrial sector by implementing a similar but full-scale treatment plant.

The potential of algae and aquatic macrophytes in the pharmaceutical and personal care products (PPCPs) environmental removal: a review.

The presence of emerging contaminants, such as pharmaceuticals and personal care products (PPCPs), in aquatic environments has received increasing attention in the last years due to the various possible impacts on the dynamics of the natural environment and human health. In global terms, around 771 active pharmaceutical substances or their transformation products have been detected at levels above their respective detection limit. Additionally, 528 different compounds have been detected in 159 countries. Seeking to overcome potential ecotoxicological problems, several studies have been conducted using different technologies for PPCPs removal. Recently, the use of macro, microalgae, and aquatic macrophytes has been highlighted due to the excellent bioremediation capacity of these organisms and easy acclimatization. Thus, the present review aims to outline a brief and well-oriented scenario concerning the knowledge about the bioremediation alternatives of PPCPs through the use of macro, microalgae, and aquatic macrophytes. The characteristics of PPCPs and the risks of these compounds to the environment and human health are also addressed. Moreover, the review indicates the opportunities and challenges for expanding the use of biotechnologies based on algae and aquatic macrophytes, such as studies dedicated to relate the operational criteria of these biotechnologies with the main PPCPs removal mechanisms. Finally, algae and macrophytes can compose green and ecological biotechnologies for wastewater treatment, having great contribution to PPCPs removal.

Swine wastewater treatment in high rate algal ponds: Effects of Cu and Zn on nutrient removal, productivity and biomass composition.

This study aimed to evaluate the simultaneous interferences of Cu and Zn found in swine wastewater (SW) in the development of microalgae considering real conditions of cultivation in high rate algal ponds (HRAPs). Ten HRAPs on a pilot scale were fed with SW with different mixtures of Cu (0.5-3.0 mg/L) and Zn (5.0-25.0 mg/L). The interferences of these metals in removing nutrients (N-NH4+ and soluble phosphorus (Ps)) from the SW were determined. In addition, this study evaluated the effects on biomass growth and biochemical composition. Chlorella sp. was dominant in all HRAPs and the condition that potentiated its growth occurred in medium containing 1.8 mg Cu/L + 15.0 mg Zn/L, while higher concentrations conferred inhibition. Only Cu compromised the removal rates of N-NH4+ while the effects of Zn were not significant. Contrary, Zn interfered with Ps removal rates, but the impact of Cu was not significant. The greatest Cu applications increased the protein levels by biomass (50.5-55.2 %). Carbohydrate accumulation was favored by conditions that inhibited the development of microalgae due to either limitation or excess of metals. Copper and Zn compromised the levels of lipids, and the control treatment had the highest content (24.5 %). The presence of Cu and Zn changed the dynamics of HRAPs regarding nutrient removal, productivity, and biochemical composition of the biomass.

Evaluation of high rate ponds operational and design strategies for algal biomass production and domestic wastewater treatment.

This study evaluated the effect of high rate ponds (HRPs) depth on algal biomass production during domestic wastewater treatment. HRPs were evaluated for 20, 30, and 40 cm depths, with and without CO2 supplementation. In addition, 40 cm deep HRP with ultraviolet (UV) pre-disinfection was evaluated. The concentration of chlorophyll-a as a function of time for each evaluated condition was represented by logistic models that were after submitted to cluster analysis. The 20 cm HRPs presented higher chlorophyll-a concentration, reaching a maximum of 5.8 and 4.3 mg L-1, in the HRPs with and without CO2 addition, respectively. Ammonia nitrogen and soluble phosphorus were greater removed in shallower HRPs. The addition of CO2 influenced the nutrient removal processes, optimizing nutrient recovery by biomass assimilation. HRP configuration did not influence organic matter removal (~40% of removal efficiency in all HRPs), predominant microalgae genera (Chlorella sp. and Scenedesmus), and E. coli inactivation (removal of ~2 log units), except for the 20 cm HRP without CO2 that had removal of 4 log units due to high pH values. For HRPs with CO2 addition and UV pre-disinfection, the models for 40 cm were grouped together with those obtained for 30 cm HRPs, indicating the same behavior for chlorophyll-a production as a function of time. Thus, it can be concluded that the evaluated strategies represent alternatives for reducing HRP area requirements. Moreover, results may represent advancement and major contributions for HRP design criteria.

A life cycle assessment of energy recovery using briquette from wastewater grown microalgae biomass.

Microalgae biomass (MB) is a promising source of renewable energy, especially when the cultivation is associated with wastewater treatment. However, microalgae wastewater technologies still have much to improve. Additionally, microalgae biomass valorization routes need to be optimized to be a sustainable and feasible source of green bioenergy. Thus, this paper aimed to evaluate the environmental impacts of the production of briquettes from MB, cultivated during domestic wastewater treatment. Also, it was evaluated how much the drying of the MB affected the life cycle and the environment. Improvements in the life cycle to mitigate the environmental impacts of this energy route were proposed. Cradle-to-gate modeling was applied to obtain a life cycle assessment (LCA) from cultivation to the valorization of MB, through its transformation into a solid biofuel. With LCA, it was possible to identify which technical aspect of the process needs to be optimized so that environmental sustainability can be achieved. Two scenarios were compared, one with the microalgae growth in a high-rate algal pond (HRAP) (scenario 1) and the other in a hybrid reactor, formed by a HRAP and a biofilm reactor (BR) (scenario 2). LCA highlighted the electric power mix, representing, on average, 60% of the total environmental impacts in both scenarios. The valorization of MB in briquettes needs to consume less energy to offset its yield. The environment suffered pressure in freshwater eutrophication, due to the release of 3.1E-05 and 3.9E-05 kg of phosphorus equivalent; in fossil resources scarcity, with the extraction of 1.4E-02 and 4.5E-02 kg of oil equivalent; and in climate change, by the emission of 1.0E-01 and 1.9E-01 kg of carbon dioxide (CO2) equivalent, in scenarios 1 and 2, respectively. Scenario 1 was highly damaging to terrestrial ecotoxicity, with the release of 3.5E-01 kg of 1,4 Dichlorobenzene, coming from the CO2 used in MB growth. This category was the one that most negatively pressured the environment, differing from scenario 2, in which this input was not required. This was the only impact category in which scenario 2 had a better environmental performance when compared to scenario 1. Cotton, required in scenario 2, represented up to 87% of emissions in some of the evaluated categories. Despite the impacts that occurred in the two modeled scenarios, the environmental gains due to the use of wastewater for microalgae growth, replacing the synthetic cultivation medium, stood out. In the sensitivity analysis, two alternative scenarios were proposed: (i) electricity consumption for drying has been reduced, due to the natural decrease of MB humidity, and (ii) MB briquettes were considered a substitute for coal briquettes. Results indicated that pressures on climate change and fossil resource scarcity were eliminated in both scenarios and this also occurred for freshwater eutrophication in scenario 2. This paper contributes to the improvement and development of converting MB routes into more sustainable products, causing less pressure on the environment. Also, the study contributes to filling a gap in the literature, discussing methods and technologies to be improved, and consequently making microalgae biotechnology environmentally feasible and a potential renewable energy alternative.

Hydrothermal carbonization of microalgae biomass produced in agro-industrial effluent: Products, characterization and applications.

Hydrothermal carbonization is a thermochemical treatment whose objective is to convert carbohydrate components of a given biomass into carbon-rich material in an aqueous medium. Biomass of wastewater grown microalgae is among the various potential biomasses for this route. However, operational parameters of hydrothermal carbonization for different types of biomass are still being investigated. In general, larger temperature ranges (180-260 °C) are applied to woody biomasses, which have fibrous and/or ligneous structures and, therefore, are more thermally stable than algae biomass. This study presents the hydrothermal carbonization of microalgae biomass cultivated in an agro-industrial effluent. For this purpose, a Parr reactor was operated at different temperatures (130, 150 and 170 °C) and retention times (10, 30 and 50 min). Results showed improvements in the properties of the hydrochar, mainly energy yield and carbon concentration, after the thermochemical treatment. Energy recovery was improved, as well as hydrophobicity of the carbonized material. It was observed that in the retention time of 10 min, the increase in temperature provided an increase of 7.53% in the yield of solids. On the other hand, in the retention times of 30 and 50 min, when the temperature was increased, the solid yield decreased 6.70% and 0.92%, respectively. Thus, the highest yield of solids (77.72%) and energy (78.21%) was obtained at the temperature of 170 °C and retention time of 10 min. There was a high ash content in the raw biomass (32.99%) and an increase of approximately 3% in the carbonized material, regardless of the applied treatment. With the exception of potassium and sodium, the other macro and micronutrients were concentrated in the hydrochar after thermochemical treatment, indicating the potential of the material for agriculture application, in addition to energy use. Results showed that the retention time was the most significant operational parameter of the process.

Innovative hybrid system for wastewater treatment: High-rate algal ponds for effluent treatment and biofilm reactor for biomass production and harvesting.

The use of algal biomass still faces challenges associated with the harvesting stages. To address this issue, we propose an innovative hybrid system, in which a biofilm reactor (BR) operates as an algal biomass production and harvesting unit connected to a high-rate algal pond (HRAP), a wastewater treatment unit. BR did not interfered with the biomass chemical composition (protein = 32%, carbohydrates = 11% and total lipids = 18%), with the wastewater treatment (removals efficiency: chemical oxygen demand = 59%, ammonia nitrogen = 78%, total phosphorus = 16% and Escherichia coli = 1 log unit), and did not alter the sedimentation characteristics of the biomass (sludge volume index = 29 mg/L and humidity content = 92%) in the secondary settling tank of the hybrid system. On the other hand, the results showed that this technology achieved a biomass production about 2.6x greater than the conventional system without a BR, and the efficiency of harvesting of the hybrid system was 61%, against 22% obtained with the conventional system. In addition, the BR promoted an increase in the density (~1011 org/m2) and diversity of microalgae in the hybrid system. Chlorella vulgaris was the most abundant species (>60%) from the 4th week of operation until the end of the experiment. Hence, results confirm that the integration of BR into a wastewater treatment plant optimised the production and harvesting of biomass of the hybrid system, making it a promising technology. The importance of economic and environmental analysis studies of BR is highlighted in order to enable its implementation on a large scale.

Biomass production in high rate ponds and hydrothermal liquefaction: Wastewater treatment and bioenergy integration.

Against the worldwide energy crisis and climate change, new forms of energy generation have been investigated. Among the possibilities, microalgae are considered potential feedstock for biofuels production. However, there are still important challenges to overcome. In this context, the integration of biomass cultivation and the treatment of different types of wastewater can represent a source of nutrients and water, with the additional benefit of reducing the discharge of pollutant loads into water bodies. The wastewater grown biomass is composed by a microorganism consortium. These microorganisms can develop important symbiotic relationships for the optimization of biomass production. However, the success of algal biomass cultivation in effluents also involves the development of efficient reactors, which ranges from design criteria to operational parameters. High rate ponds are the most suitable reactors for such a purpose, within the context of a wastewater treatment plant. In this reactor, the addition of CO2 is an important parameter for pH control and, consequently, will influence nutrient assimilation. Another relevant operational parameter is the pond depth, which will have a major role in radiation availability along the water column. With respect to the energy use of the biomass, hydrothermal liquefaction (HTL) represents an interesting alternative for wastewater grown biomass, since the process does not require complete drying of the biomass, its bio-oil production efficiency is not necessarily attached to the lipid content and may present a positive energy balance. In addition, the possibility of using the HTL by-products, especially the water soluble products, in the context of a biorefinery, represents a route for nutrient recycling, residue minimization, and cost reduction.

A review of biochemical and thermochemical energy conversion routes of wastewater grown algal biomass.

Microalgae are recognized as a potential source of biomass for obtaining bioenergy. However, the lack of studies towards economic viability and environmental sustainability of the entire production chain limits its large-scale application. The use of wastewaters economizes natural resources used for algal biomass cultivation. However, desirable biomass characteristics for a good fuel may be impaired when wastewaters are used, namely low lipid content and high ash and protein contents. Thus, the choice of wastewaters with more favorable characteristics may be one way of obtaining a more balanced macromolecular composition of the algal biomass and therefore, a more suitable feedstock for the desired energetic route. The exploration of biorefinery concept and the use of wastewaters as culture medium are considered as the main strategic tools in the search of this viability. Considering the economics of overall process, direct utilization of wet biomass using hydrothermal liquefaction or hydrothermal carbonization and anaerobic digestion is recommended. Among the explored routes, anaerobic digestion is the most studied process. However, some main challenges remain as little explored, such as a low energy pretreatment and suitable and large-scale reactors for algal biomass digestion. On the other hand, thermochemical conversion routes offer better valorization of the algal biomass but have higher costs. A biorefinery combining anaerobic digestion, hydrothermal carbonization and hydrothermal liquefaction processes would provide the maximum possible output from the biomass depending on its characteristics. Therefore, the choice must be made in an integrated way, aiming at optimizing the quality of the final product to be obtained. Life cycle assessment studies are critical for scaling up of any algal biomass valorization technique for sustainability. Although there are limitations, suitable integrations of these processes would enable to make an economically feasible process which require further study.

Microalgae based biofertilizer: A life cycle approach.

Waste, especially biomass in general, is a large reservoir of nutrients that can be recovered through different technologies and used to produce biofertilizers. In the present study, environmental impacts of the production of microalgae biomass-based phosphate biofertilizer compared to triple superphosphate through life-cycle assessment conducted in the Simapro® software were investigated. The functional unit of the analysis was 163 g of P for both fertilizers. Phosphorus was recovered from a meat processing industry effluent in a high-rate algal pond. Impacts related to the entire biofertilizer chain impacted mainly on climate changes (3.17 kg CO2eq). Microalgae biofertilizer had higher environmental impact than conventional fertilizer in all impact categories, highlighting climate change and terrestrial ecotoxicity. An ideal scenario was created considering that: all energy used comes from photovoltaic panels; in the separation step a physical method will be used, without energy expenditure (i.e. gravimetric sedimentation) and; biomass will be dried in a drying bed instead of the thermal drying. In this scenario, the impact of biofertilizer approached considerably those of triple superphosphate. When impacts of biomass cultivation and concentration stages were disregarded, drying step was of great relevance, contributing to increase biofertilizer impacts. More research is needed to optimize the algae production chain and determine the possibility of obtaining higher added value products more environmental attractive.

Algal biomass from wastewater: soil phosphorus bioavailability and plants productivity.

The cultivation of microalgae in wastewater allows to obtain a biomass concentrated in nutrients and organic material. This biomass added to phosphate fertilizers can promote a slow release of the nutrient and consequently a higher absorption of phosphorus (P). The objective of this study was to investigate P uptake by plants subjected to triple superphosphate (TSP) fertilization, added with microalgae biomass (MB) grown in wastewater. TSP was added with different MB proportions in order to verify if there would be a different behaviour in P release for millet (Pennisetum glaucum L.) plants. With the proportion that maximized P accumulation in plants, a second experiment was carried out to investigate whether MB exerts influence of P diffusion in the soil. Finally, a third trial was conducted in a greenhouse, where TSP and TSP + 12% MB were applied to the soil under different phosphorus doses in corn (Zea mays L.). The proportion of MB in TSP that maximized the increase of P content and concentration in plants was approximately 12% MB. From this proportion, a reduction in the values of the variables analysed in the plant with the increase of the proportion of MB in the biofertilizer was observed. Similar behaviour was observed when evaluating P diffusion in sandy and clay soils. Fertilizers TSP and TSP + 12% MB showed no difference in P diffusion in the soil, while the ratio of 30% MB clearly impaired P diffusion. In a greenhouse, the P content presented significant difference for the tests carried out with TSP and TSP + 12% MB fertilizer, in which the latter provided higher P recovery rate by plants. Therefore, MB added to TSP had a positive influence on plant development and its P recovery capacity when applied in a proportion of 12% MB to the fertilizer mass.

Energy recovery in high rate algal pond used for domestic wastewater treatment.

High rate algal pond (HRAP) was evaluated according to its energy potential and productivity by two rates, net energy ratio (NER) and specific biomass productivity. All energy inputs were calculated according to one HRAP with pre-ultraviolet disinfection treating anaerobic domestic sewage. The outputs were calculated for two energetic pathways: lipid and biogas production for the raw biomass (RB) and biomass after lipid extraction. The non-polar lipid content in dry biomass was 7.6%, reaching a daily lipid productivity of 0.2 g/m2·day and the biogas production potential was 0.20 m3/kg solids. For the biomass after lipid extraction, the biogas production reached 2.6 m3/kg solids. NER values of 10-3 for the RB were similar for lipids and biogas routes. The specific biomass productivity was 0.7 mg/kJ. For the residual biomass, after lipid extraction, NER value was 10-2 for the integrated route (lipids + biogas) and the specific biomass productivity of the extracted biomass was 0.4 mg/kJ. The best energetic pathway was to integrate both lipids and biogas route.