Highly deformable bi-continuous conducting polymer hydrogels for electrochemical energy storage.

Conducting polymer hydrogels with inherent flexibility, ionic conductivity and environment friendliness are promising materials in the fields of energy storage. However, a trade-off between mechanical and electrochemical properties has limited the development of flexible/stretchable conducting polymer hydrogel electrodes, owing to the intrinsic conflict among mechanical and electrical phases. Here, we report a reliable design to enable conducting polymer with both exceptional mechanical and electrical/electrochemical performance through the construction of bi-continuous conducting polymer crosslinked network. The resultant bi-continuous conducting polymer hydrogels (BCPH) demonstrate significantly improved mechanical and electrochemical properties compared to the conventional conducting polymer hydrogel (CPH) electrode. BCPH presents a high specific capacitance of 715 F g-1 at 0.5 A/g, a high mechanical strength (∼1 MPa) and a large stretchability (∼300%). Enabled by such intrinsically deformability and electrochemical properties, we further demonstrate its utility in flexible solid-state supercapacitor (FSSC), which exhibits an outstanding specific capacitance of 760 mF cm-2 at 2 mA cm-2, excellent electrochemical stability with 81% capacitance retention after 5000 charge/discharge cycles, and superior bending cycle stability. This simple and scalable strategy provides a platform for the fabrication of high-performance conducting hydrogel electrodes for various wearable electronic equipment.

Stimulated Raman Scattering Microscopy Reveals Aberrant Triglyceride Accumulation in Lymphatic Metastasis of Papillary Thyroid Carcinoma.

Lipid metabolic alterations are known to play a crucial role in cancer metastasis. As a key hub in lipid metabolism, intracellular neutral lipid accumulation in lipid droplets (LDs) has become a signature of aggressive human cancers. Nevertheless, it remains unclear whether lipid accumulation displays distinctive features in metastatic lesions compared to the primary ones. Here, we integrated multicolor stimulated Raman scattering (SRS) imaging with confocal Raman spectroscopy on the same platform to quantitatively analyze the amount and composition of LDs in intact human thyroid tissues in situ without any processing or labeling. Inspiringly, we found aberrant accumulation of triglycerides (TGs) in lymphatic metastases but not in normal thyroid, primary papillary thyroid carcinoma (PTC), or normal lymph node. In addition, the unsaturation degree of unsaturated TGs was significantly higher in the lymphatic metastases from patients diagnosed with late-stage (T3/T4) PTC compared to those of patients diagnosed with early-stage (T1/T2) PTC. Furthermore, both public sequencing data analysis and our RNA-seq transcriptomic experiment showed significantly higher expression of alcohol dehydrogenase-1B (ADH1B), which is critical to lipid uptake and transport, in lymphatic metastases relative to the primary ones. In summary, these findings unravel the lipid accumulation as a novel marker and therapeutic target for PTC lymphatic metastasis that has a poor response to the regular radioactive iodine therapy.

Accurate Embolization for Endoleak after F-TEVAR of Thoracic Aortic Dissection by Detachable Coils.

OBJECTIVES: To evaluate the efficacy and clinical outcomes of accurate embolization of endoleaks after fenestrated thoracic endovascular aortic repair (F-TEVAR) for thoracic aortic dissections. METHODS: Twenty patients with endoleaks (17 type I and 3 type II) after fenestrated thoracic endovascular aortic repair (F-TEVAR) were embolized using detachable and ordinary coils. We assessed the success rate and complications of the operation, and its effects, through clinical and CT follow-up. RESULTS: The mean clinical follow-up duration was 25.68 ± 11.07 months (3-44 months). During follow-up, all endoleaks were completely embolized and aortic remodeling was improved. Secondary endoleaks occurred in four patients who were embolized twice. No other complications or death were reported. CONCLUSION: Embolization using detachable and ordinary coils is effective and safe for the treatment of endoleaks after fenestrated thoracic endovascular aortic repair.

Breathable and Stretchable Organic Electrochemical Transistors with Laminated Porous Structures for Glucose Sensing.

Dynamic glucose monitoring is important to reduce the risk of metabolic diseases such as diabetes. Wearable biosensors based on organic electrochemical transistors (OECTs) have been developed due to their excellent signal amplification capabilities and biocompatibility. However, traditional wearable biosensors are fabricated on flat substrates with limited gas permeability, resulting in the inefficient evaporation of sweat, reduced wear comfort, and increased risk of inflammation. Here, we proposed breathable OECT-based glucose sensors by designing a porous structure to realize optimal breathable and stretchable properties. The gas permeability of the device and the relationship between electrical properties under different tensile strains were carefully investigated. The OECTs exhibit exceptional electrical properties (gm ~1.51 mS and Ion ~0.37 mA) and can retain up to about 44% of their initial performance even at 30% stretching. Furthermore, obvious responses to glucose have been demonstrated in a wide range of concentrations (10-7-10-4 M) even under 30% strain, where the normalized response to 10-4 M is 26% and 21% for the pristine sensor and under 30% strain, respectively. This work offers a new strategy for developing advanced breathable and wearable bioelectronics.

Three-Dimensional Printing to Guide Fenestrated/Branched TEVAR in Triple Aortic Arch Branch Reconstruction With a Curative Effect Analysis.

PURPOSE: To summarize experience with and the efficacy of fenestrated/branched thoracic endovascular repair (F/B-TEVAR) using physician-modified stent-grafts (PMSGs) under 3D printing guidance in triple aortic arch branch reconstruction. MATERIALS AND METHODS: From February 2018 to April 2022, 14 cases of aortic arch aneurysms and 30 cases of aortic arch dissection (22 acute aortic arch dissection and 8 long-term aortic arch dissection)were treated by F/B-TEVAR in our department, including 34 males and 10 females, with an average age of 59.84 ± 11.72 years. Three aortic arch branches were affected in all patients. A 3D-printed model was made according to computed tomography angiography images and used to guide the fabrication of PMSGs. All patients were followed up. RESULTS: A total of 132 branches were successfully reconstructed with no case of conversion to open surgery. The average operation time was 4.97 ± 1.40 hours, including a mean 44.05 ± 7.72 minutes for stent-graft customization, the mean postoperative hospitalization duration was 9.91 ± 4.47 days, the average intraoperative blood loss was 480.91 mL (100-2810 mL), and the mean postoperative intensive care unit monitoring duration was 1.02 days (0-5 days). No deaths occurred within 30 days of surgery. Postoperative neurological complications occurred in 1 case (2.3%), and retrograde type A dissection occurred in 1 case (2.3%). CONCLUSION: Compared with conventional surgery, triple aortic arch branch reconstruction under the guidance of 3D printing is a minimally invasive treatment method with the advantages of accurate positioning, rapid postoperative recovery, few complications, and reliable short- to mid-term effects. CLINICAL IMPACT: At present the PMSG usually depend on imaging data and software calculation. With the guidance of 3D printing technology, image data could be transformed into 3D model, which has improved the accuracy of the positioning of the fenestrations. The diameter reduction technique and the internal mini cuff technique have made a complement to the slimed-down fenestration selection process and the low rate of endoleak. As reproducible study, our results may provide reference for TEVAR in different cases.

Outcomes of tibial pilon fracture fixation based on four-column theory.

OBJECTIVES: To assess the medium-term functional and radiological outcomes, as well as injury mechanisms, fracture patterns and demographics of typical pilon fractures and pilon variant fractures treated based on the four-column theory in adults. METHODS: A retrospective comparative study was performed. Demographics of typical pilon and pilon variant fractures, injury mechanisms, OTA/AO classification, Rüedi-Allgöwer and the four-column classification were analyzed for the cohort. Radiographic ankle arthrosis (modified Kellgren-Lawrence 3/4), Burwell Charnley Score, and AOFAS score were also analyzed. RESULTS: There were 142 pilon fractures met the inclusion and exclusion criteria for this study, of which 77(54.23%) were females and 65 (45.77%) were males, with an average of 48 (range, 18-86)years. One hundred twenty-five posterior columns fractured in 142 pilon fractures, and the posterior columns were most prone to fractures. Ninety cases of posterior pilon fractures in 142 pilon fractures were single posterior column fractures with or without medial or lateral malleolar fractures. The average age (51, range, 18-86 years) of low-energy pilon fractures was older than the average age (42, range, 19-66 years) of high-energy pilon fractures significantly. The average time (5, range, 0-17 days) from injury to definitive internal fixation of the low-energy group was shorter than the average time (9, range, 0-21 days) from injury to definitive internal fixation of the high-energy group significantly. The average of AOFAS (87, range, 56-100) of the low-energy group is higher than the average of AOFAS (82, range, 47-100) of the high-energy group significantly. There were more male patients and more die-punch or intercalary fractures in high energy groups significantly. There were more medial and lateral malleolar fractures in low-energy groups. Compared with the non-multiple column group, the multiple-column group had more Rüedi-Allgöwer type III cases, more modified Kellgren-Lawrence 3/4 cases and lower AOFAS score significantly. However, the numbers of Burwell Charnley Score type 1 and 2 cases were not significantly different between the two groups. CONCLUSIONS: Kinds of pilon variants should be recognized. Outcomes of high-energy pilon fractures were worse than low-energy pilon fractures. The four-column theory can be applied to typical pilon fracture and pilon variants in adults.

Mechanism of Astrin in Head and Neck Squamous Cell Carcinoma.

Head and neck squamous cell carcinoma(HNSCC) is a malignant epidermal tumor that seriously threatens human life and health. The main factors affecting the death of patients are local recurrence and lymph node metastasis. Astrin antibody is the basic component of the mitotic spindle required for normal chromosome separation and later development. There are few domestic studies on the mechanism of Astrin in HNSCC. Based on this, this article is studying Astrin in HNSCC. The expression and function of Astrin, and analyze its correlation with clinical pathological parameters and prognosis of patients, and further explore the relevant mechanisms involved in the progression of Astrin in HNSCC. In this experiment, the real-time fluorescent quantitative polymerase chain reaction (PCR) method was used to detect the expression of the Astrin antibody in HNSCC cell lines A and B. Secondly, this article will focus on high metastatic HNSCC cells B. Divided into five groups (blank control group, overexpression positive group, overexpression negative control group, expression suppression positive group, expression suppression negative control group), using real-time fluorescent quantitative PCR technology to detect the expression of Astrin in each group, and then speculate the mechanism of Astrin in HNSCC. Experiments have shown that Astrin is expressed in A and B cells, but its expression in B is significantly higher than its expression in A, and the difference is statistically significant (P<0.001). This shows that the inhibition of Astrin expression has a significant anti-tumor effect and that Astrin plays an important role in the occurrence and development of tumors. It is expected to provide new ideas and reference basis for exploring new therapeutic strategies for targeted therapy of HNSCC.

Biomechanical and clinical evaluation of interlocking hip screw in Pauwels â ¢ femoral neck fractures: A comparison with inverted triangle cannulated screws.

Purpose: To compare biomechanical and clinical properties of the novel internal fixation Interlocking Hip Screw (IHS) and conventional inverted triangle cannulated screws (ITCS) for treatment of Pauwels Ⅲ femoral neck fractures. Methods: Twenty synthetic femurs were osteotomized to simulate 70° Pauwels Ⅲ femoral neck fractures and randomly divided into two groups: Group IHS and Group ITCS. Specimens were loaded in quasi-static ramped and cyclical compression testing in 25° adduction to analyze for axial stiffness, failure load, and interfragmentary displacement. 21 matched patients with Pauwels Ⅲ femoral neck fracture who received closed reduction and internal fixation from January 2020 to January 2021 in both Group IHS and Group ITCS. Demographic data, time to surgery, operating duration, intraoperative blood loss, number of fluoroscopies, length of hospital stay, fracture healing time, Harris Hip Score (HHS), the score of Visual Analogue Scale (VAS) and complications such as nonunion, avascular necrosis, and femoral neck shortening were compared. Results: All specimens in the two groups survived in the axial and cyclical compression test. The axial stiffness was significantly higher for Group IHS (277.80 ± 26.58 N/mm) versus Group ITCS (205.33 ± 10.46 N/mm), p < 0.05. The maximum failure loading in Group IHS performed significantly higher than in Group ITCS (1,400.48 ± 71.60 N versus 996.76 ± 49.73 N, p < 0.05). The interfragmentary displacement of the cyclic loading test for Groups IHS and Group ITCS was 1.15 ± 0.11 mm and 1.89 ± 0.14 mm, respectively, p < 0.05. No significant difference was found in terms of demographic data, time to surgery, intraoperative blood loss, length of hospital stay and the occurrence of nonunion and avascular necrosis between groups. Shorter operating duration and fewer intraoperative fluoroscopic views were noticed using IHS compare to ITCS, p < 0.05. The HHS was 72.14 ± 5.76 and 86.62 ± 5.01 in Group IHS, and was 67.29 ± 5.27 and 81.76 ± 5.13 in Group ITCS at 3-month and 6-month follow-up, respectively, p < 0.05. The magnitude of femoral neck shortening was significantly lower in Group IHS compared to Group ITCS (4.80 ± 1.03 mm versus 5.56 ± 1.21 mm, p < 0.05). Conclusion: Our study demonstrated that IHS provided better biomechanical and clinical performance due to its unique biological and biomechanical mechanisms, compared with ITCS. Thus, IHS is a feasible alternative to ITCS for the fixation of Pauwels Ⅲ femoral neck fractures.

Solute Carrier Family 27 Member 6 (SLC27A6) Possibly Promotes the Proliferation of Papillary Thyroid Cancer by Regulating c-MYC.

To investigate the expression and mechanism of LSC27A6 in papillary thyroid cancer (PTC). We analyzed the differential expression of SLC27A6 in PTC tissues and normal tissues based on the TCGA database and validated it using immunohistochemistry. Wilcoxon rank sum, chi-square test, or Fisher exact exam were used to analyze the relationship between the expression of SLC27A6 and clinicopathological information. Samples were divided into two groups according to whether BRAF was mutated or not, and Wilcoxon rank sum was used to determine whether the expression of SLC27A6 was related to BRAF mutation. The effects of SLC27A6 on the proliferation, migration, and apoptosis of PTC cells were detected by cell counting kit-8 (CCK8), colony formation assay, transwell assay, and flow cytometry. Spearman correlation analysis was used to evaluate the relationship between SLC27A6 and c-MYC. Protein expression was detected by Western blot. The expression of SLC27A6 was higher in PTC and positively correlated with N stage. SLC27A6 expression was higher in samples with BRAF mutations. Down-regulation of SLC27A6 inhibited cell proliferation, migration, and invasion and induced apoptosis. Spearman correlation analysis showed that SLC27A6 was positively correlated with c-MYC. Knockdown of SLC27A6 inhibited c-MYC expression. Our results suggest that SLC27A6 is overexpressed in PTC tissues and affects the progression of PTC by regulating c-MYC.

Experimental Study on the Synergistic Effect between Evaporation Weathering and Emulsification of Oil Spills.

First, a range of experiments using a stainless steel shallow plate in a thermostatic oscillator were carried out to simulate evaporation weathering of oil spills under different temperatures, wind velocities, oil film thicknesses, and wave conditions. The information on influencing factors of evaporation weathering could be obtained. Then, evaporation experiments of four oil samples with three emulsification states were conducted, and the effect of emulsification on evaporation of oil spills was investigated. The characteristics of each operation were described, mass loss characteristics of oil spills with time were plotted, and the effects of evaporative weathering processes under different conditions were quantitatively compared. A high-precision visualization system was utilized to simulate experimentally oil spill emulsification processes, and the effect of evaporative weathering on emulsification weathering of oil spills was investigated. The results of evaporation experiments showed that the increase of temperature could promote the evaporative weathering. The thin film thickness was beneficial to evaporation of oil spills. The increment of the wind speed could promote evaporation behavior when the wind velocity was small, but the increase of velocity had little effect on oil evaporation when the wind speed was large. Wave conditions had little effect on oil evaporation under the conditions of this experiment. The effect of different emulsification states on oil evaporation was not consistent. Unstable or semistable water-in-oil emulsions inhibited oil evaporation at the initial stage of evaporation, but water evaporation would increase oil-phase evaporation with the destruction of the emulsion structure. Stable water-in-oil emulsions inhibited evaporation weathering. The evaporation weathering of oil was conducive to the emulsification of oil.

pUDK-HGF Gene Therapy to Relieve CLI Rest Pain and Ulcer: A Phase II, Double-Blind, Randomized Placebo-Controlled Trial.

This phase II clinical trial investigated the efficacy and safety of intramuscular injection of plasmid pUDK-HGF, which encodes the human hepatocyte growth factor gene in patients with critical limb ischemia. Resting pain patients (n = 119) and patients with leg ulcers (n = 121) were enrolled as two cohorts and randomized to receive pUDK-HGF treatment on days 0, 14, and 28. In the resting pain cohort, the proportion of patients with complete pain relief on day 180 after receiving pUDK-HGF injection, as the primary outcome, was significantly higher than that of the placebo group on the same day (p = 0.0148). More responders with >50% pain reduction were also observed in the pUDK-HGF groups than in the placebo groups (p = 0.0168). In the ulcer cohort of patients, pUDK-HGF treatment tended to be superior to the placebo in the percentage of patients with both complete ulcer healing and >50% ulcer healing. No significant differences in the incidence of adverse events (AEs) or serious AEs were observed among the groups. The mid-dose pUDK-HGF (6 mg) was the most efficacious, and is therefore an appropriate dose for use in a phase III clinical trial. This study was approved by the China Food and Drug Administration (2013L00637), China Clinical Trial Registry URL: www.chinadrugtrials.org.cn. Unique Identifier: 20130378.

Treatment of Stanford type A aortic dissection with triple pre-fenestration, reduced diameter, and three-dimensional-printing techniques: A case report.

BACKGROUND: A 63-year-old female was diagnosed with acute Stanford type A aortic dissection. The patient had pain in the chest and back for 1 wk. The computed tomography angiography (CTA) showed Stanford type A aortic dissection (Myla type III aortic arch). The intimal tear was located at the top of the aortic arch and retrograded to the ascending aorta. CASE SUMMARY: Preoperatively, a three-dimensional (3D)-printed model of the aortic arch was made according to CTA data. Then, under the guidance of the 3D-printed aortic model, a pre-fenestrated stent-graft was customized, and the diameter of the stent-graft was reduced intraoperatively by surgeons. 3D printing, triple pre-fenestration, and reduced diameter techniques were used during the surgery. The CTA examinations were performed at the 3rd mo and 1st year after the surgery; the results showed that the aortic dissection was repaired without endoleak, and all three branches of the aortic arch remained unobstructed. CONCLUSION: Applying the triple pre-fenestration technique for aortic arch lesions was feasible and minimally invasive in our case. The technique provides a new avenue for thoracic endovascular aortic repair of Stanford type A aortic dissection.

A Quantum Expectation Value Based Language Model with Application to Question Answering.

Quantum-inspired language models have been introduced to Information Retrieval due to their transparency and interpretability. While exciting progresses have been made, current studies mainly investigate the relationship between density matrices of difference sentence subspaces of a semantic Hilbert space. The Hilbert space as a whole which has a unique density matrix is lack of exploration. In this paper, we propose a novel Quantum Expectation Value based Language Model (QEV-LM). A unique shared density matrix is constructed for the Semantic Hilbert Space. Words and sentences are viewed as different observables in this quantum model. Under this background, a matching score describing the similarity between a question-answer pair is naturally explained as the quantum expectation value of a joint question-answer observable. In addition to the theoretical soundness, experiment results on the TREC-QA and WIKIQA datasets demonstrate the computational efficiency of our proposed model with excellent performance and low time consumption.

Endovascular Repair of Aortic Dissection Involving the Left Subclavian Artery by Castor Stent Graft: A Multicentre Prospective Trial.

OBJECTIVE: The left subclavian artery (LSA) origin can be intentionally covered by stent grafts, to provide adequate proximal landing zones during thoracic endovascular repair for Stanford type B aortic dissections (TBADs). To preserve the LSA, a novel single branched stent graft, named "Castor" was designed and a clinical trial conducted to investigate its suitability. METHODS: From April 2013 to March 2015, 73 patients with TBAD were treated by Castor stent grafts at 11 Chinese tertiary hospitals as part of a single arm prospective clinical trial. There were 50 acute (<2 weeks [68.5%]) and 23 chronic aortic dissections (>2 weeks [31.5%]). RESULTS: The technical success rate was 97% (n = 71/73). The two failures were caused by occlusion of the branch section of the stent graft. There were four intra-operative endoleaks (two type Ia, two type B from the LSA). The endoleak rate was 5% (n = 4/73). There was one in hospital death and no major complications. The median follow up time was 61 months (range 48-72 months). The mortality was 5% (n = 4/73) within one year and 7% within six years (n = 5/73). Two deaths were of unknown cause and three were not related to the aorta. Two new entry tears were found on the proximal or distal edge of the stent graft and were retreated endovascularly. Six occlusions of the branch section of the Castor stent graft were found, and the follow up patency rate of the branch section was 93% (n = 63/68). Two intra-operative endoleaks were left during follow up and eventually disappeared according to the latest computed tomography angiograms. CONCLUSION: For patients with TBADs needing anchoring proximal to the origin of LSA, the Castor single branched stent graft may provide an easily manipulated, safe, and effective endovascular treatment.

How to get better TAD? Relationship between anteversion angle of nail and position of femoral neck guide pin during nailing of intertrochanteric fractures.

BACKGROUND: To demonstrate the correlation between guide pin-shaft angle (PSA) at the anteroposterior film and anteversion angle of guide pin at the lateral film and investigate whether excellent tip-apex distance (TAD) can be obtained by changing the entry point via axial rotation of the main intramedullary nail. METHODS: Fifty patients with intertrochanteric femoral fractures (IFFs) undergoing internal fixation with intramedullary nails under 2D fluoroscopy were retrospectively enrolled. Both of the PSA at the anteroposterior film and anteversion angle at the lateral film before and after adjustment of the guide pin were collected. Pearson correlation analysis was performed to investigate their correlation. Intraoperative and postoperative outcomes were recorded. Furthermore, the software of Mimics 10.0 and Pro/E were used to establish the 3D models of the proximal femur and main intramedullary nail/guide pin, respectively. Surgery was simulated on the Pro/E software platform and solid geometry analysis was conducted to calculate the correlation between the PSA and the anteversion angle. RESULTS: Pearson correlation analysis indicated there was a positive correlation between PSA and anteversion angle, with the correlation coefficient of 0.902 (p < 0.01). By altering the PSA and anteversion angle, TAD was adjusted to be less than 25 mm in all patients. The mean operative time, fluoroscopy time and length of hospital stay were 65.82 ± 11.16 min, 2.03 ± 0.79 min and 6.66 ± 2.49 d. Thirty-one patients received blood transfusions (3.55 ± 1.95 U). Fracture reduction was considered to be good or acceptable in all patients. Complications occurred only in 6 patients (12.00%). At a 3-month follow-up, the mean Timed Up and Go was 31.54 ± 20.95 s and Harris Hip Score was 72.88 ± 8.79. The 3D surgery model also showed when the main intramedullary nail was externally rotated or internally rotated of 20° at the standard location, the PSA of guide pin at the anteroposterior position and anteversion angle of the guide pin at the lateral position were simultaneously increased or decreased. CONCLUSION: Our findings suggest altering the PSA and anteversion angle may be beneficial for obtaining excellent TAD and achieving superior outcomes.

Use of 3D Printing to Guide Creation of Fenestrations in Physician-Modified Stent-Grafts for Treatment of Thoracoabdominal Aortic Disease.

Purpose: To summarize the experience and outcomes of total endovascular repair of thoracoabdominal aortic disease using 3-dimensional (3D) printed models to guide on-site creation of fenestrations in aortic stent-grafts. Materials and Methods: From April 2018 to March 2019, 34 patients (mean age 58±14 years; 24 men) with thoracoabdominal aortic disease were treated in our department. Nineteen patients had thoracoabdominal aortic dissection and 15 had thoracoabdominal aortic aneurysm. Preoperatively, a 3D printed model of the aorta was made according to computed tomography images. In the operating room, the main aortic stent-graft was completely released in the 3D printed model, and the position of each fenestration or branch was marked on the stent-graft. The fenestrations were then made using an electric pen. Wires were sewn to the edge of the fenestrations using nonabsorbable sutures. After customization, the aortic stent-graft was reloaded into the delivery sheath and deployed. Results: The printing process took ~5 hours (1 hour for image reconstruction, 3 hours for printing, and 1 hour for postprocessing). The physician-modified stent-grafts had a total of 107 fenestrations secured by 102 bridging stent-grafts, including 73 covered stents and 29 bare stents. The average procedure time was 5.6±1.2 hours, including a mean 1.3 hours for stent-graft customization. No renal insufficiency or paraplegia occurred. Two branch arteries were lost during the operation. One patient (3%) died 1 week after surgery from a retrograde dissection rupture. One patient developed a minor cerebral infarction postoperatively. The mean follow-up time was 8.5 months. There was 1 endoleak from a fenestration (coil embolized) and 4 distal ruptures of the aortic dissection (3 treated and 1 observed). Conclusion: Three-dimensional printing can be used to guide creation of fenestrated stent-grafts for the treatment of thoracoabdominal aortic diseases involving crucial branches. This technique appears to be more accurate than the traditional measurement method, with short-term follow-up demonstrating the safety and reliability of the method. However, further research and development are needed.

Total endovascular repair of an intraoperative stent-graft deployed in the false lumen of Stanford type A aortic dissection: A case report.

BACKGROUND: A 46-year-old male underwent ascending aortic replacement, total arch replacement, and descending aortic stent implantation for Stanford type A aortic dissection in 2016. However, an intraoperative stent-graft was deployed in the false lumen inadvertently. This caused severe iatrogenic thoracic and abdominal aortic dissection, and the dissection involved many visceral arteries. CASE SUMMARY: The patient had pain in the chest and back for 1 mo. A computed tomography scan showed that the patient had secondary thoracic and abdominal aortic dissection. The ascending aortic replacement, total arch replacement, and descending aortic stent implantation for Stanford type A aortic dissection were performed 2 years prior. An intraoperative stent-graft was deployed in the false lumen. Endovascular aneurysm repair was performed to address this intractable situation. An occluder was used to occlude the proximal end of the true lumen, and a covered stent was used to direct blood flow back to the true lumen. A three-dimensional printing technique was used in this operation to guide pre-fenestration. The computed tomography scan at the 1stmo after surgery showed that the thoracic and abdominal aortic dissection was repaired, with all visceral arteries remaining patent. The patient did not develop renal failure or neurological complications after surgery. CONCLUSION: The total endovascular repair for false lumen stent-graft implantation was feasible and minimally invasive. Our procedures provided a new solution for stent-graft deployed in the false lumen, and other departments may be inspired by this case when they need to rescue a disastrous stent implantation.

Estimating and Analyzing Long-Term Multi-GNSS Inter-System Bias Based on Uncombined PPP.

With the development of precise positioning with multi-GNSS, the inter-system bias (ISB) has become an issue that cannot be ignored. ISB is introduced from the differences among satellite reference clocks and different receiver hardware delay biases. To analyze the characteristics of multi-GNSS ISB, the precise point positioning (PPP) with full-rank uncombined model was derived for GLONASS, BDS, GALILEO, while the GPS receiver clock was selected as the reference. In addition, a recommended ISB parameter processing model was adopted. Data of 28-days from the Multi-GNSS Experiment (MGEX) station was used to estimate and analyze the ISB parameters. Based on a statistical analysis of the acquired data, results demonstrate that: (a) The rms of multi-GNSS PPP positional bias can reach 4.6 mm, 3.4 mm and 8.5 mm for E, N and U directions, respectively, which guarantees the reliability and accuracy of the ISB parameter solution. (b) The intra-day ISB time series of the three groups is relatively stable with standard deviations less than 0.6 ns. The ISB parameters between the GALILEO and GPS system are the most stable and the standard deviation was the smallest, at about 0.37 ns, which may be related to the good signal quality of the GALILEO system. (c) The mean of the single-day solution of the ISB parameter is not stable and the amplitude of the jump can be up to 60 ns. However, each station shows a similar variation for the same ISB parameter on the same day. The situation is independent of the type of receiver and antenna; however, it may be affected by the satellite reference clock of different systems. (d) There is a clear relationship between the ISB parameters and receiver types.

Intensified nitrogen removal by heterotrophic nitrification aerobic denitrification bacteria in two pilot-scale tidal flow constructed wetlands: Influence of influent C/N ratios and tidal strategies.

This study investigated the influence of C/N ratios and tidal strategies on nitrogen removal and bacterial communities in two pilot-scale tidal flow constructed wetlands (TFCWs) with simultaneous nitrification-denitrification process. Heterotrophic nitrification aerobic denitrification (HNAD) was the main nitrogen transformation pathway in both TFCWs. High C/N ratios and effluent circulation at low temperature promoted HNAD in TFCWs with high nitrogen removal efficiencies (72.6%-95.5% for NH4+-N and 70.9%~91.8% for TN). Effluent circulation had more influence on bacterial community structure and diversity than C/N ratios. Among 16 detected genera related to nitrogen removal, HNAD bacteria (HNADB) were abundant. Especially, some dominant HNADB (e.g. Aeromonas, Hydrogenophage and Gemmobacter) were core genera, showing positive interactions with other genera related to nitrogen removal. Tidal strategies had more contribution to the shifts in these genera than C/N ratios. This study highlights the importance of HNADB in pilot-scale TFCWs and their responses to C/N ratios and tidal strategies.

Three-Dimensional Printing to Guide the Application of Modified Prefenestrated Stent Grafts to Treat Aortic Arch Disease.

BACKGROUND: The aim of this study was to summarize the experience and outcomes of total endovascular repair of aortic arch disease using three-dimensional (3D) printing to guide the application of modified prefenestrated/branched stent grafts. PATIENTS AND METHODS: From April 2018 to March 2019, 17 patients with aortic arch disease were treated in our department. Five patients had an aortic arch aneurysm and 12 had undergone an aortic arch dissection. Thirteen men and 4 were women, with an average age of 57.82 ± 10.47 years. Preoperatively, a 3D-printed model of the aorta was made according to computed tomography data. Then, under the guidance of the 3D-printed aortic model, modified prefenestrated/branched stent grafts were prepared, and the diameter of the stent grafts was reduced intraoperatively by a physician for total endovascular repair. Aortic computed tomography angiography was performed 3 and 6 months after the surgery. RESULTS: All procedures were completed in one stage with no conversions to sternotomy. Among all 17 patients, the operation was successful in 16. One patient was treated with a chimney graft and a stent graft fenestrated in situ because of distortion of the stent. The success rate of the technique was 94.18%. The average operation time was 4.18 ± 1.57 hr, and no patients died. No neurologic complications, such as cerebral infarction or paraplegia, were observed during the follow-up period. CONCLUSIONS: Three-Dimensional printing can be used to help guide the treatment of aortic arch disease using modified prefenestrated/branched stent grafts. This minimally invasive total treatment technique is accurate, allows quick recovery, and has a low complication rate. The short-term follow-up data show the safety and reliability of the method; however, further research and development are needed.