Textured Perovskite/Silicon Tandem Solar Cells Achieving Over 30% Efficiency Promoted by 4-Fluorobenzylamine Hydroiodide.

Monolithic textured perovskite/silicon tandem solar cells (TSCs) are expected to achieve maximum light capture at the lowest cost, potentially exhibiting the best power conversion efficiency. However, it is challenging to fabricate high-quality perovskite films and preferred crystal orientation on commercially textured silicon substrates with micrometer-size pyramids. Here, we introduced a bulky organic molecule (4-fluorobenzylamine hydroiodide (F-PMAI)) as a perovskite additive. It is found that F-PMAI can retard the crystallization process of perovskite film through hydrogen bond interaction between F- and FA+ and reduce (111) facet surface energy due to enhanced adsorption energy of F-PMAI on the (111) facet. Besides, the bulky molecular is extruded to the bottom and top of perovskite film after crystal growth, which can passivate interface defects through strong interaction between F-PMA+ and undercoordinated Pb2+/I-. As a result, the additive facilitates the formation of large perovskite grains and (111) preferred orientation with a reduced trap-state density, thereby promoting charge carrier transportation, and enhancing device performance and stability. The perovskite/silicon TSCs achieved a champion efficiency of 30.05% based on a silicon thin film tunneling junction. In addition, the devices exhibit excellent long-term thermal and light stability without encapsulation. This work provides an effective strategy for achieving efficient and stable TSCs.

Diffusible Capping Layer Enabled Homogeneous Crystallization and Component Distribution of Hybrid Sequential Deposited Perovskite.

Nowadays, the development of wide-bandgap perovskite by thermal evaporation and spin-coating hybrid sequential deposition (HSD) method has special meaning on textured perovskite/silicon tandem solar cells. However, the common issues of insufficient reaction caused by blocking of perovskite capping layer are exacerbated in HSD, because evaporated precursors are usually denser with higher crystallinity and the widely used additive-assisted microstructure is also difficult to access. Here, a facile "diffusible perovskite capping layer" (DPCL) strategy to solve this dilemma is presented. With DPCL, crystallization alleviation of perovskite and more diffusion channels of organic salts can be realized simultaneously, contributing to a homogenization process. The resultant perovskite films exhibit complete conversion, uniform crystallization, enhanced quality, and reduced defect, leading to obvious improvements in device efficiency, repeatability, and stability. This work offers a way to promote the development of textured tandems a step further.

Multifunctional Additive CdAc2 for Efficient Perovskite-Based Solar Cells.

Polycrystalline perovskite films fabricated on flexible and textured substrates often are highly defective, leading to poor performance of perovskite devices. Finding substrate-tolerant perovskite fabrication strategies is therefore paramount. Herein, this study shows that adding a small amount of Cadmium Acetate (CdAc2 ) in the PbI2 precursor solution results in nano-hole array films and improves the diffusion of organic salts in PbI2 and promotes favorable crystal orientation and suppresses non-radiative recombination. Polycrystalline perovskite films on the flexible substrate with ultra-long carrier lifetimes exceeding 6 µs are achieved. Eventually, a power conversion efficiency (PCE) of 22.78% is obtained for single-junction flexible perovskite solar cells (FPSCs). Furthermore, it is found that the strategy is also applicable for textured tandem solar cells. A champion PCE of 29.25% (0.5003 cm2 ) is demonstrated for perovskite/silicon tandem solar cells (TSCs) with CdAc2 . Moreover, the un-encapsulated TSCs maintains 109.78% of its initial efficiency after 300 h operational at 45 °C in a  nitrogen atmosphere. This study provides a facile strategy for achieving high-efficiency perovskite-based solar cells.

CsPbCl3 -Cluster-Widened Bandgap and Inhibited Phase Segregation in a Wide-Bandgap Perovskite and its Application to NiOx -Based Perovskite/Silicon Tandem Solar Cells.

Nickel oxide (NiOx ) is an attractive hole-transport material for efficient and stable p-i-n metal-halide perovskite solar cells (PSCs). However, an undesirable redox reaction occurs at the NiOx /perovskite interface, which results in a low open-circuit voltage (VOC ), instability, and phase separation of the NiOx -based wide-bandgap perovskite (Br > 20%). In order to simultaneously address the abovementioned phase separation problem and redox chemistry at the perovskite/NiOx interface, the bandgap is widened from 1.64 to 1.67 eV by adding inorganic CsPbCl3 -clusters (3 mol%) to the Cs22 Br15 perovskite precursor solution. Moreover, adding extra 2 mol% CsCl enriches the NiOx /perovskite interface with Cl, thereby preventing the redox reaction at the interface, while controlling the Br content to within 15% improves the photostability of the wide-bandgap perovskite. Consequently, the power conversion efficiency (PCE) of a single-junction p-i-n PSC increases from 17.82% to 19.76%, which leads to the fabrication of highly efficient monolithic p-i-n-type NiOx -based perovskite/silicon tandem solar cells with PCEs of up to 27.26% (certified PCE: 27.15%). The perovskite to an n-i-p-type perovskite/silicon tandem solar cell is also applied to deliver a VOC of 1.93 V and a final efficiency of 25.5%. These findings provide critical insight into the fabrication of highly efficient and stable wide-bandgap perovskites.

Quasi-Heteroface Perovskite Solar Cells.

Perovskite solar cells (PSCs) have attracted unprecedented attention due to their rapidly rising photoelectric conversion efficiency (PCE). In order to further improve the PCE of PSCs, new possible optimization path needs to be found. Here, quasi-heteroface PSCs (QHF-PSCs) is designed by a double-layer perovskite film. Such brand new PSCs have good carrier separation capabilities, effectively suppress the nonradiative recombination of the PSCs, and thus greatly improve the open-circuit voltage and PCE. The root cause of the performance improvement is the benefit from the additional built-in electric field, which is confirmed by measuring the external quantum efficiency under applied electric field and Kelvin probe force microscope. Meanwhile, an intermediate band gap perovskite layer can be obtained simply by combining a wide band gap perovskite layer with a narrow band gap perovskite layer. Tunability of the band gap is obtained by varying the film thicknesses of the narrow and wide band gap layers. This phenomenon is quite different from traditional inorganic solar cells, whose band gap is determined only by the narrowest band gap layer. It is believed that these QHF-PSCs will be an effective strategy to further enhance PCE in PSCs and provide basis to further understand and develop the perovskite materials platform.

Solution-processed highly conductive PEDOT:PSS/AgNW/GO transparent film for efficient organic-Si hybrid solar cells.

Hybrid solar cells based on n-Si/poly(3,4-ethylenedioxythiophene):poly(styrene- sulfonate) (PEDOT:PSS) heterojunction promise to be a low cost photovoltaic technology by using simple device structure and easy fabrication process. However, due to the low conductivity of PEDOT:PSS, a metal grid deposited by vacuum evaporation method is still required to enhance the charge collection efficiency, which complicates the device fabrication process. Here, a solution-processed graphene oxide (GO)-welded silver nanowires (AgNWs) transparent conductive electrode (TCE) was employed to replace the vacuum deposited metal grid. A unique "sandwich" structure was developed by embedding an AgNW network between PEDOT:PSS and GO with a figure-of-merit of 8.6×10(-3) Ω(-1), which was even higher than that of sputtered indium tin oxide electrode (6.6×10(-3) Ω(-1)). A champion power conversion efficiency of 13.3% was achieved, because of the decreased series resistance of the TCEs as well as the enhanced built-in potential (Vbi) in the hybrid solar cells. The TCEs were obtained by facile low-temperature solution process method, which was compatible with cost-effective mass production technology.