Study on triaxial compression performance and damage characteristics of fiber-reinforced ecological matrix cementing gangue gypsum fill material.

Polypropylene fiber was equally mixed into alkali-activated slag fly ash geopolymer in order to ensure the filling effect of mine goaf and improve the stability of cemented gangue paste filling material with ecological matrix. Triaxial compression tests were then conducted under various conditions. The mechanical properties and damage characteristics of composite paste filling materials are studied, and the damage evolution model of paste filling materials under triaxial compression is established, based on the deviatoric stress-strain curve generated by the progressive failure behavior of samples. Internal physical and chemical mechanisms of the evolution of structure and characteristics are elucidated and comprehended via the use of SEM-EDS and XRD micro-techniques. The results show that the fiber can effectively improve the ultimate strength and the corresponding effective stress strength index of the sample within the scope of the experimental study. The best strengthening effect is achieved when the amount of NaOH is 3% of the mass of the solid material, the amount of fiber is 5‰ of the mass of the solid material, and the length of the fiber is about 12 mm. The action mode of the fiber in the sample is mainly divided into single-grip anchoring and three-dimensional mesh traction. As the crack initiates and develops, connection occurs in the matrix, where the fiber has an obvious interference and retardation effect on the crack propagation, thereby transforming the brittle failure into a ductile failure and consequently improving the fracture properties of the ecological cementitious coal gangue matrix. The theoretical damage evolution model of a segmented filling body is constructed by taking the initial compaction stage end point as the critical point, and the curve of the damage evolution model of the specimen under different conditions is obtained. The theoretical model is verified by the results from the triaxial compression test. We concluded that the experimental curve is in good agreement with the theoretical curve. Therefore, the established theoretical model has a certain reference value for the analysis and evaluation of the mechanical properties of paste filling materials. The research results can improve the utilization rate of solid waste resources.

Resource utilization of MSWI fly ash supporting TiO2/BiOCl nanocomposite for enhanced photocatalytic degradation of sodium isopropyl xanthate: Mechanism and performance evaluation.

The removal of organic pollutants in water environments and the resource utilization of solid waste are two pressing issues around the world. Facing the increasing pollution induced by discharge of mining effluents containing sodium isopropyl xanthate (SIPX), in this work, municipal solid waste incineration fly ash (MSWI FA) was pretreated by hydrothermal method to produce stabilized FA, which was then innovatively used as support for the construction of FA/TiO2/BiOCl nanocomposite (FTB) with promoted photocatalytic activity under visible light and natural sunlight. When the content of FA was 20 wt% and the mass ratio of TiO2 to BiOCl was 4:6, a remarkable performance for the optimal FTB (20-FTB-2) was achieved. Characterizations demonstrated that TiO2 and BiOCl uniformly dispersed on FA contributing to high surface area and broad light adsorption of FTB, which exhibits excellent adsorption capacity and light response ability. Build in electric field formed in the interface of TiO2/BiOCl heterojunction revealed by density functional theory calculations accelerated the separation of photoinduced e- and h+, leading to high efficiency for SIPX degradation. The synergetic effect combined with adsorption and photocatalytic degradation endowed 20-FTB-2 superior SIPX removal efficiency over 99% within 30 min under visible light and natural sunlight irradiation. The photocatalytic degradation pathways of SIPX were determined through theoretical calculations and characterizations, and the toxic byproduct CS2 was effectively eliminated through oxidation of •O2-. For 20-FTB-2, reusability of photocatalyst was showed by cycle tests, also the concentrations of main heavy metals (Pb, Zn, Cu, Cr, and Cd) in the liquid phases released during photocatalyst preparation process (< 1 mg/L) and photodegradation process (< 8.5 µg/L) proved the satisfactory stability with low toxicity. This work proposed a novel strategy to develop efficient and stable support-based photocatalysts by utilizing MSWI FA and realize its resource utilization.

Reduction of heavy metals in municipal solid waste incineration fly ash followed by making transparent glass.

Municipal solid waste incineration (MSWI) fly ash is a hazardous waste containing heavy metals. Secondary aluminum dross (SAD) is a hazardous waste discharged from aluminum smelting, containing active aluminum nitride (AlN). In this work, heavy metals from MSWI fly ash were reduced into alloy by AlN from SAD, and the slag was manufactured into transparent glass for building. Reduction of iron and zinc was 67 and 100 %, respectively. Reduction mechanism was explored after applying XRD, XRF and thermodynamics analysis. It was found that the reduction reaction was an ion reaction. The AlN and heavy metal oxide transformed into anionic group containing nitrogen and heavy metal cation, after entering slag. The heavy metals were reduced into alloy after electron was transferred from anionic group to cation. In addition, the reduced iron and zinc could merge into alloy, which inhibited evaporation of zinc. Yellow transparent glass was obtained after the reduction process. Yellow was come from titanium oxide, which could not be reduced by AlN. Microhardness, density and water absorption of the transparent glass were 741 HV, 2.86 g·cm-3 and 0.04 %, respectively. Leaching content of Ni, Cu, Zn and Pb of the glass were 0.1, <0.1, 0.6 and < 0.1 mg/L, respectively, all below the TCLP limit. About 115 âˆ¼ 213 dollars were earned after manufacturing 500 kg of MSWI fly ash into transparent glass. This work provided a novel idea of recycling solid waste into alloy and transparent glass for building.

High temperature melting of municipal solid waste incineration (MSWI) fly ash and co-disposal technology with blast furnaces.

With the development of municipal solid waste incineration technologies, the disposal of fly ash has become a difficult problem that many countries need to solve. High-temperature melting is a promising disposal technology. Based on this, a new process for collaborative treatment of fly ash in metallurgical blast furnaces had been proposed in this study. To explore the impact of disposal of fly ash on blast furnace production, by simulating the high-temperature reducing environment of blast furnaces, the melting changes of water-washed fly ash (W-FA), and the effects of W-FA injection on coal combustion and products (slag, iron) composition were studied. The results showed that W-FA, as a flux, could be sprayed into the blast furnace separately or mixed with coal. But when injected along with coal, W-FA would suppress the combustion of coal. After melting, the removal rates of S, P, Cl, and Pb in W-FA were 21%, 30%, 86%, and 89%, respectively. The removal rates of K, Na, and Zn were close to 100%, and Cr was basically not removed. When the proportion of W-FA to coal was less than 1%, in addition to controlling the alkalinity of the slag, the impact of W-FA on the composition of iron and slag was minimal. The successful execution of this work will not only achieve the reduction, harmless and resourceful utilization of fly ash, but also save investment and operating costs of disposal facilities, with both environmental and social benefits.

Complementary vitrification of municipal solid waste incineration fly ash from grate furnaces and fluidised bed incinerators via a co-reduction process.

The increasing application of municipal solid waste incineration (MSWI) emphasises the need for MSWI fly ash (FA) safe treatment. Based on the compositional complementarity of FA from grate furnaces (G-FA) and fluidised bed incinerators (F-FA), we proposed a co-reduction process to treat G-FA and F-FA together for producing vitrified slag and ferroalloys. The clean vitrified slag and Fe-Cr-Ni-Cu alloy were obtained with the mass ratios of 1:9 âˆ¼ 6:4 (G-FA:F-FA) at 1300℃, which is about 300℃ lower than the conventional G-FA vitrification. The metals Zn, Cd, and Pb were mostly volatilised into the flue gas for potential recovery from the secondary FA. The thermodynamic SiO2-Al2O3-CaO ternary system demonstrated that an optimal mass ratio of the two complementary FA types contributes to the system shifting to the low-temperature melting zone. The co-reduction process of G-FA and F-FA could be a promising option for FA beneficial reutilization with environmental advantages.

A field trial for remediation of multi-metal contaminated soils using the combination of fly ash stabilization and Zanthoxylumbungeanum- Lolium perenne intercropping system.

Insitu stabilization and phytoextraction are considered as two convenient and effective technologies for the remediation of toxic elements (TEs) in soils. However, the effectiveness of these two remediation technologies together on the bioavailability and phytoextraction of TEs in field trials has not been explored yet. Specifically, the remediation potential of fly ash (FA; as stabilizing agent) and ryegrass (as a TE accumulator) intercropped with a target crop for soil polluted with multiple TEs has not been investigated yet, particularly in long-term field trials. Therefore, in this study, a six-month combined remediation field experiment of FA stabilization and/or ryegrass intercropping (IR) was carried out on the farmland soils contaminated with As, Cd, Cr, Cu, Hg, Ni, Pb and Zn where Zanthoxylumbungeanum (ZB) trees as native crops were grown for years. The treatments include soil cultivated alone with ZB untreated- (control) and treated-with FA (FA), produced by burning lignite in Shaanxi Datong power plant, China, soil cultivated with ZB and ryegrass untreated- (IR) and treated-with FA (FA + IR). This was underpinned by a large-scale survey in Daiziying (China), which showed that the topsoils were polluted by Cd, Cu, Hg and Pb, and that Hg and Pb contents in the Zanthoxylumbungeanum fruits exceeded their allowable limits. The TEs contents in the studied FA were lower than their total element contents in the soil. The DTPA-extractable TEs contents of the remediation modes were as follows: FA < FA + IR < IR < control. Notably, TEs contents in the ZB fruits were lowest under the FA + IR treatment, which were decreased by 27.6% for As, 42.3% for Cd, 16.7% for Cr, 30.5% for Cu, 23.1% for Hg, 15.5% for Ni, 33.2% for Pb and 38.1% for Zn compared with the control treatment. Whereas the FA + IR treatment enhanced TEs contents in ryegrass shoots and roots, and the TEs contents in ryegrass shoots were below their regulatory limits for fodder crops. The findings confirmed that the combined remediation strategy, i.e., FA (with low content of TEs) stabilization effect and intercropping of ZB (target crop) and ryegrass (accumulating plant) could provide a prospective approach to produce target plants within safe TEs thresholds with greater economic benefits, while remediating soils polluted with multiple TEs and mitigating the potential ecological and human health risk. Those results are of great applicable concern.

Preparation and characterization of high-ash coal slime-based soil amendment as well as investigations of its adsorption performance and mechanisms towards heavy metals in soil.

In this study, high-ash coal slime-based mineral soil amendment (MSA) was prepared via the hydrothermal method using high-ash coal slime as raw material, supplemented with activator calcium oxide and additive KOH solution. After hydrothermal treatment at 230 °C for 5 h, the original crystalline phase (quartz and kaolinite) of the high-ash slime was completely transformed into hydrotalcite zeolite, tobermorite, and silicate of potassium aluminosilicate, which has the largest specific surface area. The adsorption of Pb2+ and Cd2+ was adherent to the kinetic equation of secondary adsorption and Freundlich models, and the removal of Pb2+ and Cd2+ reached up to 362.58 mg g-1 and 64.67 mg g-1. The successive releases of SiO2 and CaO from MSA conformed to the Elovich equation, whereas the releases of SiO2 in Cd-containing environments and CaO in Pb- and Cd-containing environments more closely conformed to the power function; the releases of K2O all conformed to the first-order kinetic equation. The presence of Pb2+ and Cd2+ in the environment promotes the release of potassium and calcium elements with MSA's ion-exchange ability, and attenuates the release of silicon elements. Combining Pb2+ and Cd2+ with silicon resulted in the intolerant precipitation of 3PbO·2SiO2 and Cd2SiO4. The mineral precipitation mechanism is the most important mechanism of MSA in immobilizing heavy metals, accounting for 72.7%-80.5% of the total adsorption. Further contaminated soil immobilization experiments also showed that the application of MSA significantly reduced the bioavailability of soil heavy metals. When the MSA addition amount was 1.6%, the residual state increased by 63.58%. In conclusion, preparing MSA may effectively utilize coal-based solid waste with high added value.

Design and preparation of reticular superabsorbent hydrogel material with nutrient slow-release and high shear strength for ecological remediation of abandoned mines with steep slopes.

In order to solve ecological remediation issues for abandoned mines with steep slopes, a kind of hydrogels with high cohesion and water-retaining were designed by inorganic mineral skeleton combining with polymeric organic network cavities. This eco-friendly hydrogel (MFA/HA-g-p(AA-co-AM)) was prepared with acrylic acid (AA)-acrylamide (AM) as network, which was grafted with humic acids (HA) as network binding point reinforcement skeleton and polar functional group donors, KOH-modified fly ash (MFA) as internal supporter. The maximum water absorption capacities were 1960 g/g for distilled water, which followed the pseudo-second-order model. This super water absorption was attributed to the first stage of 62 % fast absorption due to the high specific surface area, pore volume and low osmotic pressure, moreover, the multiple hydrophilic functional groups and network structure swell contributed to 36 % of the second stage slow adsorption. In addition, the pore filling of water in mesoporous channels contributed the additional 2 % water retention on the third stage. The high saline-alkali resistance correlated with the electrostatic attraction with MFA and multiple interactions with oxygen-containing functional groups in organic components. MFA and HA also enhanced the shear strength and fertility retention properties. After 5 cycles of natural dehydration and reabsorption process, these excellent characteristics of reusability and water absorption capacity kept above 97 %. The application of 0.6 wt% MFA/HA-g-p(AA-co-AM) at 15° slope could improve the growth of ryegrass by approximately 45 %. This study provides an efficient and economic superabsorbent material for ecological restoration of abandoned mines with steep slopes.

Solidification/stabilization and optimization of municipal solid waste incineration fly ash with aluminosilicate solid wastes.

Alkali-activation is an effective municipal solid waste incineration fly ash (MSWIFA) solidification/stabilization (S/S) technology. However, the characteristics of calcium-rich silica-poor aluminum phase in MSWIFA easily cause the structural instability and contamination of alkali activated MSWIFA S/S bodies. Therefore, the aluminosilicate solid wastes are used in this work to optimize the immobilization and structural properties. Results showed that incorporation of aluminosilicate solid wastes significantly improved the compressive strength and heavy metals pollution toxicity of MSWIFA S/S bodies. Compared to alkali activated MSWIFA, the compressive strength of S/S bodies with addition of coal fly ash, silica fume and granulated blast furnace slag improved by 31.0%, 47.6% and 50.8% when the curing time was 28 days, respectively. Leachability of Pb, Zn and Cd in these alkali activated MSWIFA S/S bodies was far below the threshold value specified in Standard GB16889. Aluminosilicate solid wastes provided abundant Si/Al structural units, and some new phases such as ettringite(AFt, 3CaO⋅Al2O3⋅3CaSO4⋅32H2O), calcium sulfoaluminate hydrate (3CaO⋅Al2O3⋅CaSO4⋅12H2O) and Friedel's salt (CaO⋅Al2O3⋅CaCl2⋅10H2O) can be detected in S/S matrix with aluminosilicate solid wastes, along comes increased the amount of the amorphous phases. Lower Ca/Si molar ratio tended to form the network structure gel similar to tobermorite with higher polymerization degree. Meanwhile, the silica tetrahedron of the gels changed from the oligomerization state like island to the hyperomerization state like chain, layer network or three-dimensional structure, and average molecular chain length increased. These findings provide theoretical basis for structural properties optimization and resource utilization of MSWIFA S/S matrices.

Analysis of composition characteristics and treatment techniques of municipal solid waste incineration fly ash in China.

The rapid development of the economy and society is causing an increase in the amount of municipal solid waste (MSW) produced by people's daily lives. With the strong support of the Chinese government, incineration power generation has steadily become the primary method of treating MSW, accounting for 79.86%. However, burning produces a significant amount of municipal solid waste incineration fly ash (MSWI-FA), which contains heavy metals, soluble chlorine salts, and dioxins. China's MSWI-FA yield increased by 8.23% annually to 7.80 million tons in 2022. Besides, the eastern region, especially the southeastern coastal region, has the highest yield of MSWI-FA. There are certain similarities in the chemical characteristics of MSWI-FA samples from Northeast, North, East, and South China. Zn and CaO have the largest amounts of metals and oxides, respectively. The Cl content is about 20 wt%. This study provides an overview of the techniques used in the thermal treatment method, solidification and stabilization, and separation and extraction of MSWI-FA and compares their benefits and drawbacks. In addition, the industrial applications and standard requirements of landfill treatment and resource utilization of MSWI-FA in China are analyzed. It is discovered that China's resource utilization of MSWI-FA is insufficient through the study on the fly ash disposal procedures at a few MSW incineration facilities located in the economically developed Guangdong Province and the traditional industrial city of Tianjin. Finally, the prospects for the disposal of MSWI-FA were discussed.

Mitigating ash-related alkali and heavy metals emissions in rotary kiln through oxygen-carrier-aided combustion of waste.

Rotary kiln (RK) incineration technology gains prominence in waste management, aiming to reduce pollution, recover energy, and minimize waste. Oxygen-carrier (OC)-aided incineration of waste in the RK demonstrates notable benefits by enhancing oxygen distribution uniformity and facilitating fuel conversion. However, the effects of OC on ash-related alkali and heavy metals during waste incineration in the RK remain unknown. In this study, manganese ore and ilmenite as OCs are introduced into RK during waste combustion, focusing on their effects on the bottom ashes and the behavior of alkali and heavy metals. Results show that manganese ore exhibits a decreasing reactivity due to oxygen depletion during the conversion from Mn2O3 to Mn3O4, while ilmenite maintains good reactivity due to sustained enrichment of Fe2O3 on the particles even after multiple cycles in RK. The porous structure on the surface of OCs particles verifies the cyclic reaction involving oxidation by air and reduction by fuel as OCs move between the active and passive layers of the bed. The porous OCs particles offer abundant adsorption sites for K from the gaseous phase, with surface-deposited K migrating into the particles and enhancing the OCs' capacity for K adsorption. Adding OCs promotes the formation of stable, less volatile compounds of heavy metals (As, Cr, Pb, and Zn) and enhances their retention in bottom ash while ensuring the leaching toxicity remains below Chinese national standard limits. This study enhances the understanding of OCs in incineration, guiding vital references for waste management practices and environmental sustainability.

Ni-FeOx synergy induced by metal-support interaction on Ni-impregnated incineration bottom ash for effective tar reforming.

The incineration bottom ash (IBA) was impregnated with nickel to catalyze toluene (tar surrogate) steam reforming. A toluene conversion of >80 % was achieved at 800℃ without activity decay in a 100-h test for 15 %Ni/IBA. An activation stage was observed for Ni/IBA catalysts in the initial 50 âˆ¼ 400 min under different reaction conditions. A series of experiments and characterizations were performed to explore the possible mechanisms for the activation. It was found that the iron species in IBA gradually migrated to the catalyst surface and formed a Ni-FeOx complex owing to the metal-support interaction. The synergy of Ni-FeOx played an important role in improving the activity of Ni/IBA due to the enhanced lattice oxygen activity. Additionally, Ni/IBA catalysts showed a much lower coke deposition rate than Ni/Al2O3 (1.12 vs. 3.45 mg-C/gcat∙h) because of the variable states of FeOx and the abundant basic sites caused by the alkali and alkaline earth metals contained in IBA.

Optimizing MSW incineration bottom ash reuse: A study on treated wastewater washing and leaching control.

The current study introduces an innovative methodology by utilizing treated wastewater (TWW) from an effluent treatment plant as a washing agent to enhance the characteristics of incineration bottom ash (IBA). This approach addresses sustainability concerns and promotes the circular economy by reusing wastewater generated in municipal solid waste incineration facilities. Previous research has underscored the challenges of open IBA reuse due to elevated leaching of chlorides, sulfates, and trace metal(loid)s. Thus, the experimental setup explores various combinations of washing, with or without screening, to optimize the properties of soil-like material (SLM < 4.75 mm) and overall material (OM < 31.5 mm) fractions of IBA for unrestricted applications. Batch leaching tests were conducted on treated samples, and leaching characteristics were evaluated in accordance with regulatory standards, primarily the Dutch standard for unrestricted IBA reuse. The findings reveal that washing in isolation proves insufficient to enhance IBA properties; however, washing followed by screening, specifically for removing fines (<0.15 mm), proves effective in reducing contamination. The study identifies that multiple steps of washing and screening (with recirculation) process render OM and SLM fractions suitable for unrestricted reuse with a cumulative liquid-to-solid ratio of 6 L/kg and a total washing time of 15 min. The multi-step treatment was found effective in reducing sulfate contamination by 65-74 % and chloride contamination by 83-89 % in IBA fractions. This approach offers a promising solution for overcoming the limitations associated with IBA leaching, thereby promoting sustainable waste reuse practices.

A systematic comparison of salt removal efficiency in washing treatment by using fly ashes from 13 MSWI plants in China.

Municipal solid waste incineration (MSWI) fly ash contains large amounts of Ca, Si, and other elements, giving it the potential to be used as a raw material for cement production. However, fly ash often contains a high content of salts, which greatly limits its blending ratio during cement production. These salts are commonly removed via water washing, but this process is affected by the nature and characteristics of fly ash. To clarify the influence of the ash characteristics on salt removal, a total of 60 fly ash samples from 13 incineration plants were collected, characterized, and washed. The ash characterization and cluster analysis showed that the incinerator type and flue gas purification technology/process significantly influenced the ash characteristics. Washing removed a high percentage of salts from fly ash, but the removal efficiencies varied significantly from each other, with the chlorine removal efficiency ranging from 73.76% to 96.48%, while the sulfate removal efficiency ranged from 6.92% to 51.47%. Significance analysis further revealed that the salt removal efficiency varied not only between the ash samples from different incinerators, but also between samples collected at different times from the same incinerator. The high variance of the 60 ash samples during salt removal was primarily ascribed to their different mineralogical and chemical characteristics. Mineralogical analysis of the raw and washed ash samples showed that the mineralogical forms and proportion of these salts in each ash sample greatly influenced their removal. The presence of less-soluble and insoluble chloride salts (e.g., CaClOH, Ca2Al(OH)6(H2O)2Cl etc.) in fly ash significantly affected the chlorine removal efficiency. This study also found that Fe, Mn, and Al in fly ash were negatively correlated with the dechlorination efficiency of fly ash. In summary, the different physical and chemical properties of fly ash caused great discrepancies in salt removal. Consequently, it is suggested to consider the potential impact of the ash source and ash generation time on salt removal to ensure a reliable treatment efficiency for engineering applications.

Lanthanum-modified tobermorite synthesized from fly ash for efficient phosphate removal.

Phosphate removal from water by lanthanum-modified tobermorite synthesized from fly ash (LTFA) with different lanthanum concentrations was studied. LTFA samples were characterized by X-ray diffraction, Fourier transform infrared spectroscopy, scanning electron microscopy, and Brunauer‒Emmett‒Teller specific surface area analysis. The results showed that the LTFA samples were mainly composed of mesoporous tobermorite-11 Å, and LTFA1 with a lanthanum concentration of 0.15 M had a high specific surface area (83.82 m2/g) and pore volume (0.6778 cm3/g). The phosphate adsorption capacities of LTFA samples were highest at pH 3 and gradually decreased with increasing pH. The phosphate adsorption kinetics data on LTFA samples were most accurately described by the Elovich model. The adsorption isotherms were in the strongest agreement with the Temkin model, and LTFA1 showed the highest phosphate adsorption capacity (282.51 mg P/g), which was higher than that of most other lanthanum-modified adsorbents. LTFA1 presented highly selective adsorption of phosphate with other coexisting ions (HCO3-, Cl-, SO42-, and NO3-). In addition, phosphate was adsorbed onto LTFA samples by forming inner-sphere phosphate complexes and amorphous lanthanum phosphate. This study provides technical support for development of efficient fly ash-based phosphate adsorbents.

Fly ash treatment via conventional and microwave-assisted organic acid leaching: kinetics and life cycle assessment.

Heedless disposal of oil-based fly ash contributes to the contamination of the air, water, and soil. Acid leaching of industrial solid wastes is recognized as a versatile, cost-effective, and environmentally friendly solid waste treatment approach. The present study investigated the viability of conventional leaching (CL) and microwave-assisted leaching (MAL) of predominant heavy metals from Mazut-burnt fly ash. For this purpose, the practicality of four organic acids with various specifications (ascorbic, gluconic, citric, and oxalic acids) on the dissolution efficiency of fly ash components was examined. Utilization of oxalic acid led to achieving full V recovery, complete Fe removal, and Ni enrichment in the residue in both CL and MAL setups. The Ni content of the sample was enriched from 6% in the calcinated sample to 23.7% in the oxalic acid leaching residue. Using citric acid resulted in the co-extraction of V, Ni, and Fe with nearly 70% V, 50% Ni, and 89% Fe dissolved in CL. The dissolution efficiencies were slightly lower in MAL. Oxalic acid was selected as the most promising organic acid reagent for fly ash treatment, so its CL kinetics was studied and defined by the shrinking particle model. The model showed that the controlling steps in the leaching of V differ over time, changing from a chemical reaction before 60 min to fluid film diffusion or mixing afterward. The kinetic study proved MAL as an effective technique in overcoming the leaching kinetic barriers. A life cycle assessment study was conducted to determine the environmental impacts of the proposed process. Accordingly, the MAL using oxalic acid was the most environmentally friendly process among the studied ones, and the utilization of microwaves leads to the reduction of the leaching processes' environmental impacts by decreasing the processing time.

Neighborhood-scale lead (Pb) speciation in Akron, Ohio (USA) soils: primary sources, post-deposition diagenesis, and high concentrations of labile Pb.

Lead (Pb) poses a significant risk to infants and children through exposure to contaminated soil and dust. However, there is a lack of information on Pb speciation and distribution at the neighborhood-scale. This work aimed to determine: (1) the distribution of acid-extractable (labile) Pb and other metals ([M]AE) in two neighborhoods in Akron, Ohio (USA) (Summit Lake and West Akron; n = 82 samples); and (2) Pb speciation and potential sources. Total metal concentration ([M]T) and [M]AE was strongly correlated for Pb and Zn (R2 of 0.66 and 0.55, respectively), corresponding to 35% and 33% acid-extractability. Lead and Zn exhibited a strong positive correlation with each other (R2 = 0.56 for MT and 0.68 for MAE). Three types of Pb-bearing phases were observed by electron microscopy: (1) galena (PbS)-like (5-10 µm); (2) paint chip residuals (10-20 µm); and (3) Pb-bearing Fe-oxides (20 µm). Isotope ratio values for PbAE were 1.159 to 1.245 for 206Pb/207Pb, and 1.999 to 2.098 for 208Pb/206Pb, and there was a statistically significant difference between the two neighborhoods (p = 0.010 for 206Pb/207Pb and p = 0.009 for 208Pb/206Pb). Paint and petrol are the dominant sources of Pb, with some from coal and fly ash. Lead speciation and distribution is variable and reflects a complex relationship between the input of primary sources and post-deposition transformations. This work highlights the importance of community science collaborations to expand the reach of soil sampling and establish areas most at risk based on neighborhood-dependent Pb speciation and distribution for targeted remediation.

Leachability of hexavalent chromium from fly ash-marl mixtures in Sarigiol basin, Western Macedonia, Greece: environmental hazard and potential human health risk.

Hexavalent chromium (Cr (VI)) is an environmental contaminant brining high concerns due to its higher toxicity and mobility in comparison with trivalent chromium Cr(III). Cr (VI) has been linked with several adverse health effects, including respiratory diseases, lung cancer, and skin irritation. The primary sources of it in the environment are industrial activities.Most of the time, fly ash made of lignite can release Cr(VI) when it comes into contact with water in an aquatic environment. The objective of this study is the investigation of Cr (VI) concentration in leachates of fly ash and marl mixtures and the determination of its solubility under different pH conditions. Samples of fly ash were collected from the Power Plant of Agios Dimitrios. Additionally, samples of marl were collected from the mine of South Field, and both samples were mixed and prepared in in different proportions (% w.t.). The leaching experiments were carried out according to the EN-12457/1-4 (2003) standard under different pH conditions and chemical analysis of the leachates were performed by spectrophotometry with diphenylcarbazide (DPC). The environmental footprint of Cr (VI) in the study area was significant, especially in mixtures containing higher concentrations of fly ash. A critical pH range between 6 to 12 is observed. At acidic pH values, a high release of Cr (VI) was observed, while at the mentioned critical values (pH 10-12), a gradual decrease in its leachability was noticed. The high concentrations of Cr (VI) in the industrial area studied require immediate actions in terms of managing and limiting the potential hazardous impacts on the environment and by extension on the public health by developing appropriate prevention strategies.

Exploiting fly ash as an ecofriendly pesticide/nematicide on Abesmoschus esculuntus: Insights into soil amendment-induced antioxidant fight against nematode mediated ROS.

Conventional pest control measures, such as chemical pesticides and nematicides, have limited efficacy and raise environmental concerns, necessitating sustainable and eco-friendly alternatives for pest management. Therefore, to find a complementary eco-friendly pesticide/nematicide, this study investigated the role of fly ash (FA) in managing a notorious pest, Meloidogyne javanica and its impact on the growth and physiology of Abelmoschus esculentus. Molecular characterization using SSU and LSU rDNA gene markers confirmed the identity of Indian M. javanica as belonging to the same species. Biotic stress induced by nematode infection was significantly alleviated (P < 0.05) by FA application at a 20% w/v, regulating of ROS accumulation (44.1% reduction in superoxide anions and 39.7% reduction in hydrogen peroxide content) in the host plant. Moreover, FA enhanced antioxidant defence enzymes like superoxide dismutase (46.6%) and catalase (112%) to combat nematode induced ROS. Furthermore, the application of FA at a 20% concentration significantly improved the biomass and biochemical attributes of okra. Fly ash also upregulated the activity of the important osmo-protectant proline (11.5 µmol/g FW) to mitigate nematode stress in host cells. Suppression of disease indices like gall index and reproduction factor, combined with in-vitro experiments, revealed that FA exhibits strong nematode mortality capacity and thus can be used as a sustainable and eco-friendly control agent against root-knot nematodes.

Exploring the geotechnical and microstructural properties of composite mixtures for landfill liner materials: an experimental investigation.

The present study directs the need for the development of an economical composite mix comprised locally available soil and industrial waste which satisfy the design parameters of the municipal solid waste (MSW) landfill. The local soil, bentonite, and fly ash mixtures are mixed in different proportions to evaluate the geotechnical and microstructural characteristics for suggesting an optimum composite mix that fulfills the design parameters of landfill liners. The curing periods of different mixes are also considered while evaluating the unconfined compressive strength (UCS) characteristics. The microstructure of the mixtures is examined using advanced imaging techniques, including X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDAX) to gain insights into the changes at the microscale level due to the inclusion of fly ash. It is observed that soil-bentonite-fly ash composite mix in a ratio of 65:15:20 aligns with the optimal design characteristics required for a landfill liner. Notably, for this composite mix, both liquid limit (LL) and plastic limit (PL) show a significant increase of 48.57% and 32.33% respectively, while the optimum moisture content (OMC) rises by 11.25%. Conversely, maximum dry density (MDD) experiences an 8.79% decrease. Moreover, the free swell index (FSI) escalates by 113%, whereas hydraulic conductivity (HC) records a substantial reduction of 96.04%. Moreover, the UCS exhibited a notable increase of 209% after a 28-day curing period. The highest strength is achieved initially by soil mixed with 20% fly ash, followed by a blend containing 15% bentonite. Therefore, proper fly ash content in filler and other binder materials is an effective and sustainable approach that not only solves the disposal issue but also enhances the material's engineering characteristics, justifying its suitability to be used as a landfill liner.