Ultrasonic humidifier aerosols: Observed high heavy metal enrichment and a new emission control method.

Ultrasonic humidifiers are commonly used in households to maintain indoor humidity and generate a large number of droplets or spray aerosols. However, there have been various health concerns associated with humidifier use, largely due to aerosols generated during operation. Here, we investigated the size distribution, chemical composition, and charged fraction of aerosol particles emitted from commercial ultrasonic humidifiers. Heavy metals in water used for humidifiers were found to be highly enriched in the ultrasonic humidifier aerosols (UHA), with the enrichment factors ranging from 102 to 107. This enrichment may pose health concerns for the building occupants, as UHA concentrations of up to 106 particles/cm3 or 3 mg/m3 were observed. Furthermore, approximately 90% of UHA were observed to be electrically charged, for the first time according to our knowledge. Based on this discovery, we proposed and tested a new method to remove UHA by using a simple electrical field. The designed electrical field in this work can efficiently remove 81.4% of UHA. Therefore, applying this electrical field could be an effective method to significantly reduce the health risks by UHA.

Standardized framework for assessing soil quality at antimony smelting site by considering microbial-induced resilience and heavy metal contamination.

Antimony smelting activities damage the soil and vegetation surroundings while generating economic value. However, no standardized methods are available to diagnose the extent of soil degradation at antimony smelting sites. This study developed a standardized framework for assessing soil quality by considering microbial-induced resilience and heavy metal contamination at Xikuangshan antimony smelting site. The soil resilience index (SRI) and soil contamination index (SCI) were calculated by Minimum Data Set and geo-accumulation model, respectively. After standardized by a multi-criteria quantitative procedure of modified Nemerow's pollution index (NPI), the integrated assessment of soil quality index (SQI), which is the minimum of SRINPI and SCINPI, was achieved. The results showed that Sb and As were the prominent metal(loid) pollutants, and significant correlations between SQI and SRI indicated that the poor soil quality was mainly caused by the low level of soil resilience. The primary limiting factors of SRI were Fungi in high and middle contaminated areas, and Skermanella in low contaminated area, suggesting that the weak soil resilience was caused by low specific microbial abundances. Microbial regulation and phytoremediation are greatly required to improve the soil quality at antimony smelting sites from the perspectives of pollution control and resilience improvement. This study improves our understanding of ecological effects of antimony smelting sites and provides a theoretical basis for ecological restoration and sustainable development of mining areas.

Remediation mechanism of high concentrations of multiple heavy metals in contaminated soil by Sedum alfredii and native microorganisms.

Pollution accident of nonferrous metallurgy industry often lead to serious heavy metal pollution of the surrounding soil. Phytoremediation of contaminated soil is an environmental and sustainable technology, and soil native microorganisms in the process of phytoremediation also participate in the remediation of heavy metals. However, the effects of high concentrations of multiple heavy metals (HCMHMs) on plants and native soil microorganisms remain uncertain. Thus, further clarification of the mechanism of phytoremediation of HCMHMs soil by plants and native soil microorganisms is required. Using the plant Sedum alfredii (S. alfredii) to restore HCMHM-contaminated soil, we further explored the mechanism of S. alfredii and native soil microorganisms in the remediation of HCMHM soils. The results showed that (i) S. alfredii can promote heavy metals from non-rhizosphere soil to rhizosphere soil, which is conducive to the effect of plants on heavy metals. In addition, it can also enrich the absorbed heavy metals in its roots and leaves; (ii) native soil bacteria can increase the abundance of signal molecule-synthesizing enzymes, such as trpE, trpG, bjaI, rpfF, ACSL, and yidC, and promote the expression of the pathway that converts serine to cysteine, then synthesize substances to chelate heavy metals. In addition, we speculated that genes such as K19703, K07891, K09711, K19703, K07891, and K09711 in native bacteria may be involved in the stabilization or absorption of heavy metals. The results provide scientific basis for S. alfredii to remediate heavy metals contaminated soils, and confirm the potential of phytoremediation of HCMHM contaminated soil.

Priority sources identification and risks assessment of heavy metal(loid)s in agricultural soils of a typical antimony mining watershed.

Heavy metal(loid) (HM) pollution in agricultural soils has become an environmental concern in antimony (Sb) mining areas. However, priority pollution sources identification and deep understanding of environmental risks of HMs face great challenges due to multiple and complex pollution sources coexist. Herein, an integrated approach was conducted to distinguish pollution sources and assess human health risk (HHR) and ecological risk (ER) in a typical Sb mining watershed in Southern China. This approach combines absolute principal component score-multiple linear regression (APCS-MLR) and positive matrix factorization (PMF) models with ER and HHR assessments. Four pollution sources were distinguished for both models, and APCS-MLR model was more accurate and plausible. Predominant HM concentration source was natural source (39.1%), followed by industrial and agricultural activities (23.0%), unknown sources (21.5%) and Sb mining and smelting activities (16.4%). Although natural source contributed the most to HM concentrations, it did not pose a significant ER. Industrial and agricultural activities predominantly contributed to ER, and attention should be paid to Cd and Sb. Sb mining and smelting activities were primary anthropogenic sources of HHR, particularly Sb and As contaminations. Considering ER and HHR assessments, Sb mining and smelting, and industrial and agricultural activities are critical sources, causing serious ecological and health threats. This study showed the advantages of multiple receptor model application in obtaining reliable source identification and providing better source-oriented risk assessments. HM pollution management, such as regulating mining and smelting and implementing soil remediation in polluted agricultural soils, is strongly recommended for protecting ecosystems and humans.

Simultaneous immobilization of multiple heavy metal(loid)s in contaminated water and alkaline soil inoculated Fe/Mn oxidizing bacterium.

Two strains of Fe/Mn oxidizing bacteria tolerant to high concentrations of multiple heavy metal(loid)s and efficient decontamination for them were screened. The surface of the bio-Fe/Mn oxides produced by the oxidation of Fe(II) and Mn(II) by Pseudomonas taiwanensis (marked as P4) and Pseudomonas plecoglossicida (marked as G1) contains rich reactive oxygen functional groups, which play critical roles in the removal efficiency and immobilization of heavy metal(loid)s in co-contamination system. The isolated strains P4 and G1 can grow well in the following environments: pH 5-9, NaCl 0-4%, and temperature 20-30°C. The removal efficiencies of Fe, Pb, As, Zn, Cd, Cu, and Mn are effective after inoculation of the strains P4 and G1 in the simulated water system (the initial concentrations of heavy metal(loid) were 1 mg/L), approximately reaching 96%, 92%, 85%, 67%, 70%, 54% and 15%, respectively. The exchangeable and carbonate bound As, Cd, Pb and Cu are more inclined to convert to the Fe-Mn oxide bound fractions in P4 and G1 treated soil, thereby reducing the phytoavailability and bioaccessible of heavy metal(loid)s. This research provides alternatives method to treat water and soil containing high concentrations of multi-heavy metal(loid)s.

Hybrid and enhanced electrokinetic system for soil remediation from heavy metals and organic matter.

The electrokinetic (EK) process has been proposed for soil decontamination from heavy metals and organic matter. The advantages of the EK process include the low operating energy, suitability for fine-grained soil decontamination, and no need for excavation. During the last three decades, enhanced and hybrid EK systems were developed and tested for improving the efficiency of contaminants removal from soils. Chemically enhanced-EK processes exhibited excellent efficiency in removing contaminants by controlling the soil pH or the chemical reaction of contaminants. EK hybrid systems were tested to overcome environmental hurdles or technical drawbacks of decontamination technologies. Hybridization of the EK process with phytoremediation, bioremediation, or reactive filter media (RFM) improved the remediation process performance by capturing contaminants or facilitating biological agents' movement in the soil. Also, EK process coupling with solar energy was proposed to treat off-grid contaminated soils or reduce the EK energy requirements. This study reviews recent advancements in the enhancement and hybrid EK systems for soil remediation and the type of contaminants targeted by the process. The study also covered the impact of operating parameters, imperfect pollution separation, and differences in the physicochemical characteristics and microstructure of soil/sediment on the EK performance. Finally, a comparison between various remediation processes was presented to highlight the pros and cons of these technologies.

Nitrogen-cycling processes under long-term compound heavy metal(loids) pressure around a gold mine: Stimulation of nitrite reduction.

Mining and tailings deposition can cause serious heavy metal(loids) pollution to the surrounding soil environment. Soil microorganisms adapt their metabolism to such conditions, driving alterations in soil function. This study aims to elucidate the response patterns of nitrogen-cycling microorganisms under long-term heavy metal(loids) exposure. The results showed that the diversity and abundance of nitrogen-cycling microorganisms showed negative feedback to heavy metal(loids) concentrations. Denitrifying microorganisms were shown to be the dominant microorganisms with over 60% of relative abundance and a complex community structure including 27 phyla. Further, the key bacterial species in the denitrification process were calculated using a random forest model, where the top three key species (Pseudomonas stutzei, Sphingobium japonicum and Leifsonia rubra) were found to play a prominent role in nitrite reduction. Functional gene analysis and qPCR revealed that nirK, which is involved in nitrite reduction, significantly accumulated in the most metal-rich soil with the increase of absolute abundance of 63.86%. The experimental results confirmed that the activity of nitrite reductase (Nir) encoded by nirK in the soil was increased at high concentrations of heavy metal(loids). Partial least squares-path model identified three potential modes of nitrite reduction processes being stimulated by heavy metal(loids), the most prominent of which contributed to enhanced nirK abundance and soil Nir activity through positive stimulation of key species. The results provide new insights and preliminary evidence on the stimulation of nitrite reduction processes by heavy metal(loids).

Analysis of the Chemical and Medicinal Properties of Armillaria ostoyae (Agaricomycetes) Extracts and the Presence of Heavy Metals in Dry Basidiocarps.

We investigated the chemical and medicinal properties of methanolic and acetonic extracts of Armillaria ostoyae and the presence of heavy metals in its dry basidiocarps. The chemical content of extracts was analyzed with the HPLC-DAD-MS/MS method. According to our results, the most abundant mineral was potassium; the most abundant organic acid was malic acid; the most abundant carbohydrate was fructose, and the most abundant polyphenol was chlorogenic acid. The antimicrobial potential was evaluated using the microdilution assay, and the results ranged from 0.62 to 20 mg/mL. Antioxidant potential was studied by DPPH [half-maximal inhibitory concentration (IC50) of the methanolic extract was 619.67 µg/mL and of the acetonic extract was 533.65 µg/mL] and reducing power assays (the results ranged from 0.025 to 0.078 µg/mL). Total phenolic content was presented as gallic acid equivalent (methanolic extract, 6.12 mg GAE/g; acetonic extract, 3.99 mg GAE/g). The antidiabetic potential was explored by applying the α-amylase (the results ranged from 39.62 to 44.33%) and α-glucosidase assays (the results were in the range of 0.27-2.51%). The neuroprotective activity was asserted by the acetylcholinesterase inhibition assay (the results were in the range of 3.06-6.09%). The cytotoxic potential was investigated using the microtetrazolium assay, and the IC50 values ranged from 221.96 to > 400 µg/mL. Heavy metal content of the dry basidiocarps was evaluated using the AAS method and iron was the most abundant metal. A. ostoyae is a conditionally edible mushroom, which was not studied thoroughly before, thus this research will provide valuable knowledge about this species.

Optimizing Soil Sampling for Accurately Prediction of the Potential Remediation-Effective Area in a Contaminated Agricultural Land.

To achieve food security in a contaminated agricultural land, the remediation areas usually need more samples to obtain accurate contamination information and implement appropriate measures. In this study, we propose an optimal encryption sampling design to instead of the detailed survey, which is determined by the variation of heavy metals and the technology capability of remediation, to guide soil sampling for accurately remediation in the potential remediation-effective areas (PRA). The coefficient of screening variation threshold (CSVT), considering spatial variation, technology capacity and acceptable error of sampling, together with the spatial cyclic statistics method of neighbourhood analysis, is introduced to identify and delineate the PRA. Both of the hypothetical analysis and application case studies are conducted to illustrate the advantages and disadvantages of the optimization. The results show that, compared with the detailed survey, the optimal design shows a lower overall accuracy due to its sparsely sampling at the clean area, but it exhibits a similar effect of accurately prediction in boundary delineation and further classification in the PRA in both simulation and application studies. This work provides an effective method for subsequent accurate remediation at the investigation stage and valuable insights into application combination of technology capacity and contaminated agricultural land investigation.

Soil quality and heavy metal contamination in an open dumpsite in Navrongo, Ghana.

The increasing proximity of the Dudumbia dumpsite, an open dumpsite in Navrongo, Ghana, to human settlements necessitates an investigation of the soil quality to safeguard the environment from heavy metal toxicity. This study examined the impact of waste dumping activities on the physicochemical properties of the soil, as well as the level of heavy metal (Pb, Cd, Ni, Cr, As, Hg, Cu, Mn, and Zn) contamination and associated risks. Various contamination and risk assessment tools were used, including the geoaccumulation index (Igeo), pollution load index (PLI), potential ecological risk (Er), and potential ecological risk index (PERI). The study found significant improvements in notable soil attributes such as phosphorus (P), organic carbon (C), total nitrogen (N), calcium (Ca), magnesium (Mg), potassium (K), sodium (Na), and effective cation exchange capacity, with percentage increases ranging from 50.8 to 2078.3%. Igeo values ranged from 2.07 to 6.20, indicating contamination levels from moderate to extreme. The PLI and PERI values were 16.241 and 1810, respectively. The Er values for the heavy metals ranged from 36 to 607, indicating ecological risk levels from low to very high, with Cd and Hg posing very high risks. These results suggest that while the dumpsite soil shows improvements in some characteristics favourable for plant cultivation, waste dumping significantly contributes to heavy metal contamination. The soil at the dumpsite is deteriorated and poses significant health risks, particularly due to Cd and Hg. Therefore, remediation efforts should prioritise mitigating the risks posed by Cd and Hg.

Human Exposure to Heavy Metals over the Last 100 Years.

The primary objective of the presented research was to assess the impact of intense global economic development, over the last 100 years, on the bioaccumulation of heavy metals in the human body. This evaluation was conducted based on the measurement of heavy metals in human hair samples collected 100 years ago in present-day southern Poland.In this study, concentrations of lead (Pb), cadmium (Cd), arsenic (As), zinc (Zn), copper (Cu), iron (Fe), and selenium (Se) were measured in 61 hair samples,28 of which were obtained from individuals who lived 100 years ago, while the remaining 33 constituted the contemporary control group. The concentrations were determined using a triple quadrupole inductively coupled plasma mass spectrometer (Agilent 8900). Statistical analysis of the obtained results was conducted using the Principal Cmponent Analysis and the non-parametric Mann-Whitney test. In the case of As, Pb, Cd, and Fe, the concentrations were significantly higher in individuals who lived 100 years ago compared to those living today. Over this period, the median concentrations were shown to have decreased by 95%, 94%, 85%, and 69% for As, Pb, Cd, and Fe, respectively. No statistically significant differences were observed for Cu, Zn, and Se. The results obtained for Pb, Cd, As, and Fe unequivocally indicate that the population studied from 100 years ago was more exposed to internal contamination with these metals than people who live nowadays.

Source Identification of Potentially Toxic Metals in Plants of Alpine Ecosystems of Mt. Madra by Positive Matrix Factorization.

In this study, the concentrations of cadmium (Cd), iron (Fe), manganese (Mn), nickel (Ni), lead (Pb) and zinc (Zn) in plants sampled from Mt. Madra were investigated. Furthermore, the distribution characteristics and source identification of potentially toxic metals were investigated with the application of Positive Matrix Factorization (PMF) modelling. Samples of 26 different plant species were taken from Mt. Madra at elevations ranging from 177 to 1347 m using the multi-point sampling approach. The metal quantities measured by ICP-OES are the following sequences (mean ± SD) (mg/kg): Fe (974.96 ± 29.6) > Mn (111.81 ± 2.6) > Zn (27.28 ± 0.2) > Ni (2.17 ± 0.03) > Pb (0.77 ± 0.01) > Cd (0.12 ± 0.01). According to the plant samples in which the highest values were determined, the metals are as follows: Cd (Lathyrus laxiflorus, 0.401 mg/kg), Fe (Ajuga orientalis, 7621.207 mg/kg), Mn (Castanea sativa, 724.927 mg/kg), Ni (Prunella laciniata, 6.947 mg/kg), Pb (Crataegus stevenii, 3.955 mg/kg) and Zn (Prunella laciniata, 50.802 mg/kg). The results of the PMF model showed that Cd had an atmospheric transport factor originated and transported from industrial activites, Ni had a substrate factor, Fe, Mn, Pb and Zn were influenced by different anthropogenic factors.

A review of heavy metals pollution in riverine sediment from various Asian and European countries: Distribution, sources, and environmental risk.

Riverine sediments are important reservoirs of heavy metals, representing both historical and contemporary anthropogenic activity within the watershed. This review has been conducted to examine the distribution of heavy metals in the surface sediment of 52 riverine systems from various Asian and European countries, as well as to determine their sources and environmental risks. The results revealed significant variability in heavy metal contamination in the world's riverine systems, with certain hotspots exhibiting concentrations that exceeded the permissible limits set by environmental quality standards. Among the studied countries, India has the highest levels of chromium (Cr), cobalt (Co), manganese (Mn), nickel (Ni), zinc (Zn), cadmium (Cd), copper (Cu), and lead (Pb) contamination in its riverine systems, followed by Iran > Turkey > Spain > Vietnam > Pakistan > Malaysia > Taiwan > China > Nigeria > Bangladesh > Japan. Heavy metal pollution in the world's riverine systems was quantified using pollution evaluation indices. The Contamination Factor (CF) revealed moderate contamination (1 ≤ CF < 3) throughout the geological units, with the exception of Pb, Cd, and Cu. The Contamination Degree (CD) classifies the contamination level into different categories: Low degree of contamination (CD < 6), moderate degree of contamination (6 ≤ CD < 12), considerable degree of contamination (12 ≤ CD < 24), and a very high degree of contamination (CD ≥ 24), while the Pollution Load Index (PLI) estimate the total amount of heavy metal pollution in riverine sediments, with Turkey having the highest PLI value of 6.512, followed by Spain, Vietnam, Taiwan, Pakistan, Bangladesh, China, India, Japan, Malaysia, Iran, and Nigeria. In applied multivariate statistics, correlation analysis determined the fate and distribution of heavy metals in riverine systems, while Principal Component Analysis (PCA) elucidated the potential sources, including industrial, agrochemical, mining, and domestic wastewater discharges, lubricant leakages, multiple geogenic inputs, erosion of mafic and ultramafic rocks, and minimal atmospheric deposition. As per Potential Ecological Risk Index (PERI) perspectives, Vietnam, Spain, and Turkey have the highest ecological risk, followed by Nigeria > Pakistan > Bangladesh > China > Taiwan > Japan and Iron, while the potential risks of ∑non-carcinogenic Pb, Cr, Ni, Cu, Cd, Co, Zn, and Mn for exposed human children and adults through ingestion and dermal contact were significantly influenced between acceptable to high risk, necessitating special attention from pollution control agencies.

Minerals and trace element compositions of some seaweeds from the Marchica lagoon, North-East Mediterranean coast of Morocco.

The objective of the present study was to evaluate the mineral and heavy metals composition of different seaweeds growing in Marchica lagoon. To this end, green seaweeds, red seaweeds, and brown seaweeds were collected from three different stations in the Marchica lagoon. The highest concentration of Ca was measured in Centroceras clavulatum (17.12 ± 0.60), K in Caulerpa prolifera (15.17 ± 0.20), Na in Gracilaria dura (4.16 ± 0.03) and Hypnea musciformis (4.09 ± 0.03), Mg in Ulva rigida (2.80 ± 0.06), and the highest concentration of P was registered in Ulva intestinalis (3658 ± 14). Centroceras clavulatum and Gracilaria dura had the highest Al, Fe, and Sr levels. Cystoseira compressa had the highest As (53.8 mg/kg) and Rb (43 mg/kg). These findings suggest that seaweeds collected from Marchica lagoon could be used as potential sources of minerals and trace elements in seaweed-based products for human and animal nutrition alike.

Removal of Heavy Metals by Pseudomonas sp. - Model Fitting and Interpretation.

Industrial and urban modernization processes generate significant amounts of heavy metal wastewater, which brings great harm to human production and health. The biotechnology developed in recent years has gained increasing attention in the field of wastewater treatment due to its repeatable regeneration and lack of secondary pollutants. Pseudomonas, being among the several bacterial biosorbents, possesses notable benefits in the removal of heavy metals. These advantages encompass its extensive adsorption capacity, broad adaptability, capacity for biotransformation, potential for genetic engineering transformation, cost-effectiveness, and environmentally sustainable nature. The process of bacterial adsorption is a complex phenomenon involving several physical and chemical processes, including adsorption, ion exchange, and surface and contact phenomena. A comprehensive investigation of parameters is necessary in order to develop a mathematical model that effectively measures metal ion recovery and process performance. The aim of this study was to explore the latest advancements in high-tolerance Pseudomonas isolated from natural environments and evaluate its potential as a biological adsorbent. The study investigated the adsorption process of this bacterium, examining key factors such as strain type, contact time, initial metal concentration, and pH that influenced its effectiveness. By utilizing dynamic mathematical models, the research summarized the biosorption process, including adsorption kinetics, equilibrium, and thermodynamics. The findings indicated that Pseudomonas can effectively purify water contaminated with heavy metals and future research will aim to enhance its adsorption performance and expand its application scope for broader environmental purification purposes.

A probabilistic risk assessment of heavy metal in water and sediment: An industrially affected urban river in Bangladesh.

Human welfare and biodiversity are at risk due to the deterioration of water and sediment quality. Particularly, in last few decades, global water and sediment quality degraded due to the rapid industrialization and urbanization. This study aimed to determine the concentration of nine heavy metals and metalloid (Pb, Cr, Cd, Hg, As, Mn, Ni, Cu, and Zn) and assess the ecological risks using different pollution indices (e.g., heavy metal pollution index [HPI], Nemerow pollution index [NI], geo-accumulation index [Igeo], contamination factor [CF], degree of contamination [CD] and pollution load index [PLI], ecological risk index [ERI]) in water and sediment of the Shitalakshya River, an industrially affected urban river of Bangladesh. For the first time, 20 water and sediment samples were collected across a wider geographical area of the Shitalakshya River during both monsoon and dry seasons and analyzed using the atomic absorption spectrometer. Average concentrations of heavy metals and metalloid in water were within the Bangladesh standard except for Cr (51.69 ppb) and Mn (228.20 ppb) during monsoon season, portraying potential ecological and human health risks. Besides, average concentration of Mn (549.75 and 370.93 ppb), Ni (549.75 and 370.93 ppb), and Cu (45.34 and 36.09 ppb) in sediment during both seasons were above international standard, implying risk to aquatic sediment biota. The average HPI values indicated moderate to high contamination, whereas the NI values implied polluted water in monsoon season with severe pollution in port area of the river. Similarly, Igeo, CF, CD, and PLI elucidated different levels of contamination in the sediment, particularly during dry season. The ERI values also referred moderate ecological risk in the sediment during dry season. Overall, our findings highlight the alarming level of heavy metal pollution in the Shitalakshya River, necessitating immediate action to protect the aquatic environment, sediment biota, and human health. PRACTITIONER POINTS: This study determined the concentration of heavy metals and metalloid in water and sediment of the Shitalakshya River, Bangladesh. The study revealed that the average concentration of Cr and Mn in water exceeded national standard, whereas Mn, Ni, and Cu in sediment exceeded international limit. Potential ecological risk of heavy metals was also assessed using different pollution indices. Calculated pollution indices indicated different degree of pollution, implying critical ecological condition due to heavy metal pollution in aquatic environment and sediment biota.

Correlation between serum heavy metals and the risk of oral squamous cell carcinoma and oral potentially malignant disorders.

Oral squamous cell carcinoma (OSCC) is a serious public health problem in various Asian countries, including Sri Lanka, and a combination of cultural practices, lifestyle factors, and genetic predispositions influences the incidence of these cancers. The examination of the connection between exposure to heavy metals and the probability of developing oral potentially malignant disorders (OPMD) and OSCC has been limited in its scope, and the overall consequences of such exposure remain largely unknown. This study aims to clarify the link between serum levels of heavy metals and the risk of OSCC and OPMD. The concentrations of seven heavy metals-namely, arsenic (As), cadmium (Cd), chromium (Cr), cobalt (Co), copper (Cu), lead (Pb), and zinc (Zn)-were analyzed in serum samples from 60 cases and 15 controls in the Sri Lankan cohort. The Inductively Coupled Plasma-Optical Emission Spectrometry (ICP-OES) was used for the analysis. Subsequently, the data underwent statistical evaluation via the Kruskal-Wallis H test, using the Statistical Package for Social Sciences (SPSS) version 28 software, with a confidence interval set at 95%. A p-value less than 0.05 was considered statistically significant. The cohort consisted of 48 men and 27 women, with 15 patients each diagnosed with OSCC, OSF, OLK, and OLP, and 15 healthy controls. The study used the Kruskal-Wallis Test to compare metal concentrations across groups, finding significant differences for all metals except As and Pb. Significant associations were observed between age, past medical history, drug history, gender, smoking, alcohol consumption, and betel chewing. The Spearman Correlation test showed significant correlations between the concentrations of Cr, Co, Cu, As, and Zn and the presence of cancer/precancer conditions. The study's findings suggest that heavy metal contamination may be linked to the development of OSCC and precancerous conditions. When comparing OSCC and OPMD cases with controls, the serum concentrations of As and Pb did not differ significantly. However, Cd, Cr, Co, Cu, and Zn exhibited significantly higher concentrations among cases compared to controls (p < 0.05). This study observed significant variations in the levels of these five heavy metals among cancerous (OSCC), premalignant (OPMD), and healthy tissues, suggesting a potential role in the progression of malignancies. These findings underscore the importance of environmental pollution in this specific context.

Impact of environmental pollution on ant (Camponotus japonicus) development and labial gland disease.

Metallic pollutants can have harmful impacts on ant morphology and physiology. We studied the occurrence of labial gland disease in Camponotus japonicus from two polluted areas (traffic pollution and industrial pollution) and one non-polluted area. We further analyzed the metal levels (Al, As, Cd, Co, Cr, Cu, Fe, Hg, Mn, Ni, Pb and Zn) and morphological characteristics (head width, body mass, and other morphological traits) of both diseased and healthy workers. Our results showed that labial gland disease was only present in polluted areas, indicating that pollution stress makes ants more vulnerable to infections. Our research revealed that diseased ants in polluted areas accumulate higher levels of metals in their bodies and have lower dry weight and residual body mass compared to healthy ants in non-polluted environments, negatively impacting their development. We evaluated the importance of these elements and found that Cu has the greatest impact on the health risk of C. japonicus. Our study underscores the significant impact of environmental pollution on ant morphology and physiology and raises concerns about the broader ecological implications.

Metal concentrations in fish, crabs, and bivalve molluscs from marine waters adjacent to a multi-metals smelter and refinery.

Metal concentrations were determined in tissues of finfish, crabs, and bivalve molluscs collected from marine waters near Port Pirie, South Australia, the site of a long-standing multi-metals smelter and refinery. A general trend of tissue metal concentrations in order of highest to lowest was observed in bivalves > crabs > finfish. A lead concentration of 158 ± 6.6 mg/kg (wet wt.) was observed in blue mussels (Mytilus galloprovincialis) sampled close to the smelter. Lead concentrations correlated positively with proximity to the smelter in all biota analysed. Similar relationships were observed for cadmium, copper, zinc and selenium in all biota except razorfish (Pinna bicolor; Bivalvia: Pinnidae), which showed no correlation with proximity to the smelter for these metals. Inorganic arsenic concentrations were below the limit of reporting in the majority of the analysed samples, however inorganic arsenic concentrations in blue swimmer crabs (Portunus armatus) and blue mussels correlated with proximity to the smelter. Mercury concentrations in the biota analysed were generally low and showed variable relationships with proximity to the smelter, with no significant correlation observed in finfish and razorfish, a significant positive correlation in blue mussels, and a significant negative correlation in blue swimmer crabs. This is the first major study of metal concentrations in recreationally-targeted marine species near Port Pirie species for more than two decades. Comparison with data from previous studies conducted shows little change in tissue metal concentrations in marine biota near Port Pirie over the past 40 years.

Functional genomics and taxonomic insights into heavy metal tolerant novel bacterium Brevibacterium metallidurans sp. nov. NCCP-602T isolated from tannery effluent in Pakistan.

The strain designated NCCP-602T was isolated from tannery effluent, and displayed aerobic, gram-positive, rod-shaped cells that were characterized by oxidase negative, catalase positive, and non-motile features. The most favourable growth conditions were observed at a temperature of 30°C, pH 7.0, and NaCl concentration of 1% (w/v). It tolerated heavy metals at high concentrations of chromium (3600 ppm), copper (3300 ppm), cadmium (3000 ppm), arsenic (1200 ppm) and lead (1500 ppm). The results of phylogenetic analysis, derived from sequences of the 16S rRNA gene, indicated the position of strain NCCP-602T within genus Brevibacterium and showed that it was closely related to Brevibacterium ammoniilyticum JCM 17537T. Strain NCCP-602 T formed a robust branch that was clearly separate from closely related taxa. A comparison of 16S rRNA gene sequence similarity and dDDH values between the closely related type strains and strain NCCP-602T provided additional evidence supporting the classification of strain NCCP-602T as a distinct novel genospecies. The polar lipid profile included diphosphatidylglycerol, glycolipid, phospholipids and amino lipids. MK-7 and MK-8 were found as the respiratory quinones, while anteiso-C15:0, iso-C15:0, iso-C16:0, iso-C17:0, and anteiso-C17:0 were identified as the predominant cellular fatty acids (> 10%). Considering the convergence of phylogenetic, phenotypic, chemotaxonomic, and genotypic traits, it is suggested that strain NCCP-602 T be classified as a distinct species Brevibacterium metallidurans sp. nov. within genus Brevibacterium with type strain NCCP-602T (JCM 18882T = CGMCC1.62055T).