Protocol for detecting micro(nano)plastics released from intravenous infusion products.

Approaches for detecting micro(nano)plastics (MNPs) released from intravenous infusion products (IVIPs) are vital for evaluating the safety of both IVIPs and their derived MNPs on human health, yet current understanding is limited. Here, we present a protocol for detecting polyvinyl chloride (PVC) MNPs by combining Raman spectroscopy, scanning electron microscopy equipped with energy-dispersive X-ray spectroscopy (SEM-EDS), and pyrolysis-gas chromatography-mass spectrometry (Py-GC-MS). We describe steps for collecting, pretreating, and measuring PVC MNPs released from IVIPs. For complete details on the use and execution of this protocol, please refer to Li et al.1.

Plastic takeaway food containers may cause human intestinal damage in routine life usage: Microplastics formation and cytotoxic effect.

The microplastics and organic additives formed in routine use of plastic takeaway food containers may pose significant health risks. Thus, we collected plastic containers made of polystyrene, polypropylene, polyethylene terephthalate, polylactic acid and simulated two thermal usages, including hot water (I) and microwave treatments (M). Nile Red fluorescence staining was developed to improve accurate counting of microplastics with the aid of TEM and DLS analysis. The quantity of MPs released from thermal treatments was determined ranging from 285.7 thousand items/cm2 to 681.5 thousand items/cm2 in containers loaded with hot water with the following order: IPS>IPP>IPET>IPLA, while microwave treatment showed lower values ranging from 171.9 thousand items/cm2 to 301.6 thousand items/cm2. In vitro toxicity test using human intestinal epithelial Caco-2 cells indicated decrease of cell viability in raw leachate, resuspended MPs and supernatants, which might further lead to cell membrane rupture, ROS production, and decreased mitochondrial membrane potential. Moreover, the leachate inhibited the expression of key genes in the electron transport chain (ETC) process, disrupted energy metabolism. For the first time, we isolate the actually released microplastics and organic substances for in vitro toxicity testing, and demonstrate their potential impacts to human intestine. SYNOPSIS: Plastic take-out containers may release microplastics and organic substances during daily usage, both of which can cause individual and combined cytotoxic effects on human colon adenocarcinoma cells Caco-2.

Impact of the thermo-alkaline pretreatment on the anaerobic digestion of poly(butylene adipate-co-terephthalate) (PBAT) and poly(lactic acid) (PLA) blended plastics.

Poly(butylene adipate-co-terephthalate) (PBAT) is a biodegradable plastic that is difficult to degrade under both mesophilic and thermophilic anaerobic conditions. In this study, the impact of the thermo-alkaline pretreatment (48 h, 70 °C, 1 % w/v NaOH) on the anaerobic degradation (AD) of PBAT, poly(lactic acid) (PLA) and PBAT/PLA blended plastics was investigated. Under mesophilic conditions, pretreatment only improved the methane yield of PBAT/PLA/starch plastic (100 days, 51 and 34 NmL/g VSadd for the treated and original plastics, respectively). Under thermophilic conditions, the pretreatment increased the methanogenic rate of PLA, PBAT and PBAT/PLA/starch plastic at the beginning stage (22 days, 35 and 79 NmL/g VSadd for original and treated PBAT, respectively), but did not change the methane yield at the end of the incubation (100 days, 91 NmL/g VSadd for original and treated PBAT). The reduction in the molecular weight and the formation of pore structures on the plastic surface accelerated the utilization of plastics by microorganisms. Furthermore, the pretreated plastics tend to form microplastics (MPs) with size predominantly below 500 µm (>90 %). The numbers of MPs dynamically changed with the degradation time. Several genera of bacteria showed specific degradation of biodegradable plastics under thermophilic conditions, including Desulfitibacter, Coprothermobacter, Tepidimicrobium, c_ D8A-2 and Thermacetogenium. The results suggest that more attention should be paid to the problem of MPs arising from the thermo-alkaline pretreatment.

Insights into the effect of crystallinity on the sorption of organic pollutants to microplastics.

The environmental behavior of microplastics (MPs) has attracted global attention. Research has confirmed that MPs can strongly absorb almost every kind of pollutant and can serve as vectors for pollutant transport. In this research, the sorption isotherms of six organic pollutants with different structure on four virgin plastic particles with different crystallinity were determined. Results indicated that the hydrophobicity (KOW) of organic pollutants and the crystallinity of MPs were the two key factors that affected the sorption process of organic pollutants on MPs. Strong correlations were observed between KOW and the partition coefficient. Hydrophobic partition was one of the major mechanisms regardless of the type of organic chemical (hydrophobic, polar, or dissociable). What is more, the influence of the crystallinity of MPs on the sorption process increased with increasing hydrophobicity of the chemical. Combining this result with analyzing the related literature on the effect of crystallinity, it was concluded that the effect of crystallinity on the sorption of chemicals with strong hydrophobicity was obvious, whereas this effect was negligible for chemicals with weak hydrophobicity. The influence of the crystallinity of MPs on sorption could even exceed the influence of MPs type, so crystallinity should be considered carefully when discussing the sorption capacity of MPs. This study enhances the understanding of the sorption of organic pollutants by MPs.

Manufacturing biodegradable lignocellulosic films with tunable properties from spent coffee grounds: A sustainable alternative to plastics.

Manufacturing biodegradable lignocellulosic films from spent coffee grounds (SCG) as an alternative to commercial plastics is a viable solution to address plastic pollution. Here, the biodegradable lignocellulosic films from SCG were fabricated via a sequential alkaline treatment and ionic liquid-based dissolution process. The alkaline treatment process could swell the cell wall of SCG, change its carbohydrates and lignin contents, and enhance its solubility in ionic liquids. The prepared SCG films with different lignin contents exhibited outstanding UV blocking capability (42.07-99.99 % for UVB and 20.96-99.99 % for UVA) and light scattering properties, good surface hydrophobicity (water contact angle = 63.2°-88.7°), enhanced water vapor barrier property (2.28-6.79 × 10-12 g/m·s·Pa), and good thermal stability. Moreover, the SCG films exhibit excellent mechanical strength (50.10-81.56 MPa, tensile strength) and biodegradability (fully degraded within 30 days when buried in soil) compared to commercial plastic. The SCG films represent a promising alternative that can replace non-biodegradable plastics.

Transparent, plasticized cellulose-glycerol bioplastics for food packaging applications.

Free-standing films have been obtained by drop-casting cellulose-glycerol mixtures (up to 50 wt% glycerol) dissolved in trifluoroacetic acid and trifluoroacetic anhydride (TFA:TFAA, 2:1, v:v). A comprehensive examination of the optical, structural, mechanical, thermal, hydrodynamic, barrier, migration, greaseproof, and biodegradation characteristics of the films was conducted. The resulting cellulose-glycerol blends exhibited an amorphous molecular structure and a reinforced H-bond network, as evidenced by X-ray diffraction analysis and infrared spectroscopy, respectively. The inclusion of glycerol exerted a plasticizing influence on the mechanical properties of the films, while keeping their transparency. Hydrodynamic and barrier properties were assessed through water uptake and water vapor/oxygen transmission rates, respectively, and obtained values were consistent with those of other cellulose-based materials. Furthermore, overall migration levels were below European regulation limits, as stated by using Tenax® as a dry food simulant. In addition, these bioplastics demonstrated good greaseproof performance, particularly at high glycerol content, and potential as packaging materials for bakery products. Biodegradability assessments were carried out by measuring the biological oxygen demand in seawater and high biodegradation rates induced by glycerol were observed.

Dual-functional lignocellulosic mulch as agricultural plastic alternative for sustained-release of photosensitive pesticide and immobilizing heavy metal ions.

The extensive utilization of non-biodegradable plastic agricultural mulch in the past few decades has resulted in severe environmental pollution and a decline in soil fertility. The present study involves the fabrication of environmentally friendly paper-based mulch with dual functionality, incorporating agrochemicals and heavy metal ligands, through a sustainable papermaking/coating technique. The functional paper-based mulch consists of a cellulose fiber web incorporated with Emamectin Benzoate (EB)@ Aminated sodium lignosulfonate (ASL). The spherical microcapsules loaded with the pesticide EB exhibited an optimal core-shell structure for enhanced protection and controlled release of the photosensitizer EB (Sustained release >75 % in 50 h). Meanwhile, the ASL, enriched with metal chelating groups (-COOH, -OH, and -NH2, etc.), served as a stabilizing agent for heavy metal ions, enhancing soil remediation efficiency. The performance of paper-based mulch was enhanced by the application of a hydrophobic layer composed of natural chitosan/carnauba wax, resulting in exceptional characteristics such as superior tensile strength, hydrophobicity, heat insulation, moisture retention, as well as compostability and biodegradability (biodegradation >80 % after 70 days). This study developed a revolutionary lignocellulosic eco-friendly mulch that enables controlled agrochemical release and soil heavy metal remediation, leading to a superior substitute to conventional and non-biodegradable plastic mulch used in agriculture.

A review of starch/polyvinyl alcohol (PVA) blend film: A potential replacement for traditional plastic-based food packaging film.

In recent years, the development of environmentally friendly packaging materials using biodegradable polymers has emerged as a key challenge for scientists and consumers in response to resource depletion and environmental issues caused by plastic packaging materials. Starch and polyvinyl alcohol (PVA) are being recognized as excellent candidates for producing biodegradable food packaging films. Polymer blending has emerged as a practical approach to overcome the limitations of biopolymer films by developing films with unique properties and enhancing overall performance. This review briefly introduces the molecular structure and properties of starch and PVA, summarizes the common preparation methods and properties of starch/PVA blend films, and focuses on different strategies used to enhance starch/PVA blend films, including nanoparticles, plant extracts, and cross-linking agents. Additionally, this study summarizes the application of starch/PVA blend films as active and smart packaging in food preservation systems. This study demonstrates that starch and PVA blends have potential in manufacturing biodegradable food films with excellent properties due to their excellent compatibility and intermolecular interactions, and can be used as packaging films for a variety of foods to extend their shelf life.

Plastic and terrestrial organic matter degradation by the humic lake microbiome continues throughout the seasons.

Boreal freshwaters go through four seasons, however, studies about the decomposition of terrestrial and plastic compounds often focus only on summer. We compared microbial decomposition of 13C-polyethylene, 13C-polystyrene, and 13C-plant litter (Typha latifolia) by determining the biochemical fate of the substrate carbon and identified the microbial decomposer taxa in humic lake waters in four seasons. For the first time, the annual decomposition rate including separated seasonal variation was calculated for microplastics and plant litter in the freshwater system. Polyethylene decomposition was not detected, whereas polystyrene and plant litter were degraded in all seasons. In winter, decomposition rates of polystyrene and plant litter were fivefold and fourfold slower than in summer, respectively. Carbon from each substrate was mainly respired in all seasons. Plant litter was utilized efficiently by various microbial groups, whereas polystyrene decomposition was limited to Alpha- and Gammaproteobacteria. The decomposition was not restricted only to the growth season, highlighting that the decomposition of both labile organic matter and extremely recalcitrant microplastics continues throughout the seasons.

Bottlenecks in biobased approaches to plastic degradation.

Plastic waste is an environmental challenge, but also presents a biotechnological opportunity as a unique carbon substrate. With modern biotechnological tools, it is possible to enable both recycling and upcycling. To realize a plastics bioeconomy, significant intrinsic barriers must be overcome using a combination of enzyme, strain, and process engineering. This article highlights advances, challenges, and opportunities for a variety of common plastics.

Analysis and removal of bisphenols in recycled plastics using polyethylene glycol.

This study examines the presence of bisphenol A (BPA), S (BPS), F (BPF), and M (BPM) in various recycled plastics readily available on the market (LDPE, HDPE, PET, and PP), in light of European Food Safety Authority (EFSA) limits. Twenty samples of different origin are analyzed, cleaning treatments are applied, and the migration potential of these bisphenols into food is studied. BPM is absent in all samples, but a post-consumer recycled LDPE sample reveals high bisphenol concentrations, raising concerns, reaching 8540 ng/g, 370 ng/g, and 29 ng/g of BPA, BPS, and BPF, respectively. Migration tests show substantial migration of these contaminants into food simulants. Using a cleaning treatment with polyethylene glycol (PEG 400) reduces BPA in LDPE, HDPE, PP, and PET samples by 95%, 99%, 97% and 28%, respectively, highlighting the importance of cleaning treatments across various polymers in plastic recycling. These findings not only protect food safety but addressing environmental challenges associated with plastic recycling.

Comprehensive study of retention influencing gas chromatographic parameters affecting linear retention indices.

Retention in gas chromatographic systems has a central role in the identification of compounds even if detectors providing spectral information are used. But linear retention indices (LRI) of a single compound originating from multiple sources tend to vary greatly, probably due to differences in the experimental settings of the determinations. The effect of gas chromatographic parameters on LRI has been investigated using 41 compounds - previously identified from food contact plastics - and n-alkanes (n-C7-n-C40) used as reference series. As the reproducibility of LRIs under the same conditions is generally very good, the smallest changes in the settings often caused statistically significant, though irrelevant changes in the LRI values. Therefore, a multicriterial scoring-ranking system has been worked out to highlight the LRI value differences. Our results highlight that column length, heating rate, and film thickness can all be the reasons of the varying published LRI values. We also demonstrated that for the reproduction of LRI data, the chemistry (and not simply the polarity) of the stationary phase is crucial.

Enhancing chondrogenic differentiation of mesenchymal stem cells through synergistic effects of cellulose nanocrystals and plastic compression in collagen-based hydrogel for cartilage formation.

Collagen-based (COL) hydrogels could be a promising treatment option for injuries to the articular cartilage (AC) becuase of their similarity to AC native extra extracellular matrix. However, the high hydration of COL hydrogels poses challenges for AC's mechanical properties. To address this, we developed a hydrogel platform that incorporating cellulose nanocrystals (CNCs) within COL and followed by plastic compression (PC) procedure to expel the excessive fluid out. This approach significantly improved the mechanical properties of the hydrogels and enhanced the chondrogenic differentiation of mesenchymal stem cells (MSCs). Radially confined PC resulted in higher collagen fibrillar densities together with reducing fibril-fibril distances. Compressed hydrogels containing CNCs exhibited the highest compressive modulus and toughness. MSCs encapsulated in these hydrogels were initially affected by PC, but their viability improved after 7 days. Furthermore, the morphology of the cells and their secretion of glycosaminoglycans (GAGs) were positively influenced by the compressed COL-CNC hydrogel. Our findings shed light on the combined effects of PC and CNCs in improving the physical and mechanical properties of COL and their role in promoting chondrogenesis.

Nanoscale Simulation of Plastic Contaminants Migration in Packaging Materials and Potential Leaching into Model Food Fluids.

Polymers are the most commonly used packaging materials for nutrition and consumer products. The ever-growing concern over pollution and potential environmental contamination generated from single-use packaging materials has raised safety questions. Polymers used in these materials often contain impurities, including unreacted monomers and small oligomers. The characterization of transport properties, including diffusion and leaching of these molecules, is largely hampered by the long timescales involved in shelf life experiments. In this work, we employ atomistic molecular simulation techniques to explore the main mechanisms involved in the bulk and interfacial transport of monomer molecules from three polymers commonly employed as packaging materials: polyamide-6, polycarbonate, and poly(methyl methacrylate). Our simulations showed that both hopping and continuous diffusion play important roles in inbound monomer diffusion and that solvent-polymer compatibility significantly affects monomer leaching. These results provide rationalization for monomer leaching in model food formulations as well as bulky industry-relevant molecules. Through this molecular-scale characterization, we offer insights to aid in the design of polymer/consumer product interfaces with reduced risk of contamination and longer shelf life.

Diversity of marine bacteria growing on leachates from virgin and weathered plastic: Insights into potential degraders.

Plastic debris in the ocean releases chemical compounds that can be toxic to marine fauna. It was recently found that some marine bacteria can degrade such leachates, but information on the diversity of these bacteria is mostly lacking. In this study, we analysed the bacterial diversity growing on leachates from new low-density polyethylene (LDPE) and a mix of naturally weathered plastic, collected from beach sand. We used a combination of Catalysed Reporter Deposition-Fluorescence In Situ Hybridization (CARD-FISH), BioOrthogonal Non-Canonical Amino acid Tagging (BONCAT), and 16S rRNA gene amplicon sequencing to analyse bacterioplankton-groups specific activity responses and the identity of the responsive taxa to plastic leachates produced under irradiated and non-irradiated conditions. We found that some generalist taxa responded to all leachates, most of them belonging to the Alteromonadales, Oceanospirillales, Nitrosococcales, Rhodobacterales, and Sphingomonadales orders. However, there were also non-generalist taxa responding to specific irradiated and non-irradiated leachates. Our results provide information about bacterial taxa that could be potentially used to degrade the chemicals released during plastic degradation into seawater contributing to its bioremediation.

Microplastics in aquatic systems: An in-depth review of current and potential water treatment processes.

Plastic products, despite their undeniable utility in modern life, pose significant environmental challenges, particularly when it comes to recycling. A crucial concern is the pervasive introduction of microplastics (MPs) into aquatic ecosystems, with deleterious effects on marine organisms. This review presents a detailed examination of the methodologies developed for MPs removal in water treatment systems. Initially, investigating the most common types of MPs in wastewater, subsequently presenting methodologies for their precise identification and quantification in aquatic environments. Instruments such as scanning electron microscopy, dynamic light scattering, Fourier transform infrared spectroscopy, Raman spectroscopy, surface-enhanced Raman spectroscopy, and Raman tweezers stand out as powerful tools for studying MPs. The discussion then transitions to the exploration of both existing and emergent techniques for MPs removal in wastewater treatment plants and drinking water treatment plants. This includes a description of the core mechanisms that drive these techniques, with an emphasis on the latest research developments in MPs degradation. Present MPs removal methodologies, ranging from physical separation to chemical and biological adsorption and degradation, offer varied advantages and constraints. Addressing the MPs contamination problem in its entirety remains a significant challenge. In conclusion, the review offers a succinct overview of each technique and forwards recommendations for future research, highlighting the pressing nature of this environmental dilemma.

Effectiveness of UV-C radiation in inactivation of microorganisms on materials with different surface structures.

INTRODUCTION AND OBJECTIVE: Ultraviolet light in the UV-C band is known as germicidal radiation and was widely used for both sterilization of the equipment and creation of a sterile environment. The aim of the study is to assess the effectiveness of inactivation of microorganisms deposited on surfaces with various textures by UV-C radiation disinfection devices. MATERIAL AND METHODS: Five microorganisms (3 bacteria, virus, and fungus) deposited on metal, plastic, and glass surfaces with smooth and rough textures were irradiated with UV-C light emitted by low-pressure mercury lamp and ultraviolet emitting diodes (LEDs), from a distance of 0.5 m, 1 m, and 1.5 m to check their survivability after 20-minute exposure. RESULTS AND CONCLUSIONS: Both tested UV-C sources were effective in inactivation of microorganisms; however, LED emitter was more efficient in this respect than the mercury lamp. The survival rate of microorganisms depended on the UV-C dose, conditioned by the distance from UV-C source being the highest at 0.5 m and the lowest at 1.5 m. For the tested microorganisms, the highest survival rate after UV-C irradiation was usually visible on glass and plastic surfaces. This observation should be considered in all environments where the type of material (from which the elements of technical equipment are manufactured and may be contaminated by specific activities) is important for maintaining the proper level of hygiene and avoiding the unwanted and uncontrolled spread of microbiological pollution.

Persistent Luminescence Nanoplatform for Autofluorescence-Free Tracking of Submicrometer Plastic Particles in Plant.

The uptake of plastic particles by plants and their transport through the food chain make great risks to biota and human health. Therefore, it is important to trace plastic particles in the plant. Traditional fluorescence imaging in plants usually suffers significant autofluorescence background. Here, we report a persistent luminescence nanoplatform for autofluorescence-free imaging and quantitation of submicrometer plastic particles in plant. The nanoplatform was fabricated by doping persistent luminescence nanoparticles (PLNPs) onto polystyrene (PS) nanoparticles. Cr3+-doped zinc gallate PLNP was employed as the dopant for autofluorescence-free imaging due to its persistent luminescence nature. In addition, the Ga element in PLNP was used as a proxy to quantify the PS in the plant by inductively coupled plasma mass spectrometry (ICP-MS). Thus, the developed nanoplatform allows not only dual-mode autofluorescence-free imaging (persistent luminescence and laser-ablation ICP-MS) but also ICP-MS quantitation for tracking PS in plant. Application of this nanoplatform in a typical plant model Arabidopsis thaliana revealed that PS mainly distributed in the root (>99.45%) and translocated very limited (<0.55%) to the shoot. The developed nanoplatform has great potential for quantitative tracing of submicrometer plastic particles to investigate the environmental process and impact of plastic particles.

Chemical resistance testing of plastics: material compatibility of detergent and disinfectant products.

BACKGROUND: Surface cleaning and disinfection is a key part of breaking the chain of transmission and reducing the risk of healthcare associated infections. However, if cleaning and disinfectant formulations are incompatible with surface materials, frequent application can cause premature failure of plastics due to environmental stress cracking (ESC). Material compatibility should be considered when selecting cleaning and disinfecting products. AIM: This study evaluated the tendency of 2-in-1 wet wipes to cause ESC in commonly found healthcare plastics. METHODS: Eight ready-to-use 2-in-1 wet wipes were evaluated for their ability to cause ESC in 13 plastic surfaces in accordance with BS EN ISO-22088-3. Polymers were exposed to fluid extracted from wipes at a fixed strain of 0.5% for seven days and assessed for cracking, crazing, and tensile strength in accordance with ISO 527-2:2012. FINDINGS: All 2-in-1 wet wipes tested contained ESC agents, although the severity of ESC varied. Products with higher pH (>8.0) were responsible for 74% of failures, with 22 of the 39 tested plastics visibly cracking. Although the primary active in all tested wipe formulations were quaternary ammonium compounds, formulations that included small/medium amines or alcohol demonstrated a greater propensity for plastic cracking. CONCLUSION: Each disinfectant formulation exhibits a unique spectrum of microbial efficacy and unique potential to cause surface damage. This may result in device failures and recalls that could compromise patient and staff safety. BS EN ISO-22088-3 can support material compatibility assessments of disinfectant and detergent products before they come to market.

Isolation and characterization of bio-prospecting gut strains Bacillus safensis CGK192 and Bacillus australimaris CGK221 for plastic (HDPE) degradation.

The present work reports the application of novel gut strains Bacillus safensis CGK192 (Accession No. OM658336) and Bacillus australimaris CGK221 (Accession No. OM658338) in the biological degradation of synthetic polymer i.e., high-density polyethylene (HDPE). The biodegradation assay based on polymer weight loss was conducted under laboratory conditions for a period of 90 days along with regular evaluation of bacterial biomass in terms of total protein content and viable cells (CFU/cm2). Notably, both strains achieved significant weight reduction for HDPE films without any physical or chemical pretreatment in comparison to control. Hydrophobicity and biosurfactant characterization were also done in order to assess strains ability to form bacterial biofilm over the polymer surface. The post-degradation characterization of HDPE was also performed to confirm degradation using analytical techniques such as Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), Field emission scanning electronic microscopy (FE-SEM) coupled with energy dispersive X-ray (EDX), and Gas chromatography-mass spectrometry (GC-MS). Interestingly strain CGK221 was found to be more efficient in forming biofilm over polymer surface as indicated by lower half-life (i.e., 0.00032 day-1) and higher carbonyl index in comparison to strain CGK192. The findings reflect the ability of our strains to develop biofilm and introduce an oxygenic functional group into the polymer surface, thereby making it more susceptible to degradation.