High-performance activation of ozone by sonocavitation for BTEX degradation in water.

This work presents a novel advanced oxidation process (AOP) for degradation of emerging organic pollutants - benzene, toluene, ethylbenzene and xylenes (BTEXs) in water. A comparative study was performed for sonocavitation assisted ozonation under 40-120 kHz and 80-200 kHz dual frequency ultrasounds (DFUS). Based on the obtained results, the combination of 40-120 kHz i.e., low-frequency US (LFDUS) with O3 exhibited excellent oxidation capacity degrading 99.37-99.69% of BTEXs in 40 min, while 86.09-91.76% of BTEX degradation was achieved after 60 min in 80-200 kHz i.e., high-frequency US (HFDUS) combined with O3. The synergistic indexes determined using degradation rate constants were found as 7.86 and 2.9 for LFDUS/O3 and HFDUS/O3 processes, respectively. The higher extend of BTEX degradation in both processes was observed at pH 6.5 and 10. Among the reactive oxygen species (ROSs), hydroxyl radicals (HO•) were found predominant according to scavenging tests, singlet oxygen also importantly contributed in degradation, while O2•- radicals had a minor contribution. Sulfate (SO42-) ions demonstrated higher inhibitory effect compared to chloride (Cl-) and carbonate (CO32-) ions in both processes. Degradation pathways of BTEX was proposed based on the intermediates identified using GC-MS technique.

Photo-transformation of ofloxacin in natural aquatic conditions: Impact of indirect photolysis on the product profile and transformation mechanism.

The natural phototransformation of organic pollutants in the environment depends on several water constituents, including inorganic ions, humic substances, and pH. However, the literature information concerning the influence of various water components on the amount of phototransformation and their impact on the development of various transformation products (TPs) is minimal. This study investigated the phototransformation of ofloxacin (OFL), a fluoroquinolone antibiotic, in the presence of various water components such as cations (K+, Na+, Ca2+, NH4+, Mg2+), anions (NO3-, SO42-, HCO3-, CO32-, PO43-), pH, and humic substances when exposed to natural sunlight. The study reveals that neutral pH levels (0.39374 min⁻1) enhance the phototransformation of OFL in aquatic environments. Carbonate, among anions, shows the highest rate constant (2.89966 min⁻1), significantly influencing OFL phototransformation, while all anions exhibit a notable impact. In aquatic environments, indirect phototransformation of OFL, driven by increased reactive oxygen species, expedites light-induced reactions, potentially enhancing OFL phototransformation. A clear difference was visible in the type of transformation products (TPs) formed during direct and indirect photolysis. The impact of indirect photolysis in the product profile was evaluated by examining the unique properties of TPs in direct and indirect photolysis. The primary transformation products were generated by oxidation and cleavage processes directed towards the ofloxacin piperazinyl, oxazine, and carboxyl groups. The toxicity assessment of TPs derived from OFL revealed that among the 26 identified TPs, TP3 (demethylated product), TP7 and TP8 (decarboxylated products), and TP15 (piperazine ring cleaved product) could potentially have some toxicological effects. These findings suggest that the phototransformation of OFL in the presence of various water components is necessary when assessing this antibiotic's environmental fate.

Tungsten sulfide highly boosted Fe(III)/peroxymonosulfate system for rapid degradation of cyclohexanecarboxylic acid: Performance, mechanisms, and applications.

In this study, the Fe(III)/WS2/peroxymonosulfate (PMS) system was found to remove up to 97% of cyclohexanecarboxylic acid (CHA) within 10 min. CHA is a model compound for naphthenic acids (NAs), which are prevalent in petroleum industrial wastewater. The addition of WS2 effectively activated the Fe(III)/PMS system, significantly enhancing its ability to produce reactive oxidative species (ROS) for the oxidation of CHA. Further experimental results and characterization analyses demonstrated that the metallic element W(IV) in WS2 could provide electrons for the direct reduction of Fe(III) to Fe(II), thus rapidly activating PMS and initiating a chain redox process to produce ROS (SO4•-, •OH, and 1O2). Repeated tests and practical exploratory experiments indicated that WS2 exhibited excellent catalytic performance, reusability and anti-interference capacity, achieving efficient degradation of commercial NAs mixtures. Therefore, applying WS2 to catalyze the Fe(III)/PMS system can overcome speed limitations and facilitate simple, economical engineering applications.

A CuSO4/Bicinchoninic acid/Reducing sugar based stable and non-ROS catalyst system for the CuAAC reaction in bioanalysis.

The limitations of commonly used sodium ascorbate-based catalyst system for copper-catalyzed azide-alkyne cycloaddition (CuAAC) reaction include excess production of reactive oxygen species and rapid catalyst deactivation. In this study instead of using a highly active reducing agent, such as, sodium ascorbate, we chose reducing sugar as a mild reducing agent to build up the catalyst system for CuAAC reaction. Interestingly, the bicinchoninic acid (BCA) assay system containing reducing sugar satisfies the essential elements of the catalyst system for CuAAC reaction. We found that CuSO4/BCA/Reducing sugar system can catalyze the CuAAC reaction but with low yield. Rational analyses of various parameters in CuSO4/BCA/Glucose catalyst system suggested storage at room temperature might enhance the catalytic activity, which was proven to be the case. Importantly, the system remains stable at room temperature and minimal H2O2 was detected. Notably, our study showed that the coordination between the slow reduction of Cu(I) by reducing sugar and the selective chelation of Cu(I) by BCA is key to developing this system. The CuSO4/BCA/Reducing sugar catalyst system was successfully applied to various CuAAC reaction based bioanalyses, and it is suitable for the CuAAC reaction based bioanalyses that are sensitive to ROS or request long reaction time.

Flavonoid-rich sesame leaf extract-mediated synthesis of nanozymes: Extraction optimization, chemical composition identification and bioactivity evaluation.

Sesame leaves contain rich phenolic acids and flavonoids. However, their potential in nanozyme synthesis has not been investigated yet. Herein, we report the preparation of flavonoid-rich sesame leaf extract (SLE), composition identification, and its use in the construction of iron (Fe)-based nanozymes (Fe-SLE CPNs). SLE was obtained with an extraction yield of ∼14.5% with a total flavonoid content (TFC) of ∼850.85 mg RE/g. There were 83 flavonoid compounds in SLE, primarily including scutellarin, apigenin-7-glucuronid, narcissin, and hyperoside. Fe-SLE CPNs exhibited nanodot morphology with a hydrodynamic size of 79.34 nm and good stability in various physiological solutions, pH levels, and temperatures. The Fe-SLE CPNs were more efficient in the scavenging ability of reactive oxygen species (ROS) than SLE alone. Furthermore, a stronger anti-inflammatory effect of the Fe-SLE CPNs was shown by modulating the MyD88-NF-κB-MAPK signaling pathways. These findings imply that SLE-based nanozymes hold great potential for diverse applications.

Novel insights into the relationship between the functional groups and photoactivity of biochar-derived dissolved organic matter.

Due to the production of a large amount of biochar, highly photoactive biochar-derived dissolved organic matter (BDOM) from different sources is released into surface water. This study investigated the molecular composition of BDOM (sludge, bamboo and stalk BDOM) using Fourier transform ion cyclotron resonance mass spectrometry (FT-ICR MS) and used tetracycline (TC) as model pollutant to investigate the relationship between molecular composition and BDOM photoactivity, specifically focusing on reactive oxygen species (ROS) production. The results indicate that the fluorescence signal intensity of humic acid-like and aromatic proteins in the plant-derived BDOM are significantly higher than that derived from sewage sludge. FT-ICR MS results also showed that plant-derived BDOM contained more CHO molecular formula. Photodegradation experiments of TC mediated by various BDOM analogues demonstrated the photoactivity is highly correlated with the components and functional groups. The electrochemical experiments and density functional theory (DFT) calculations further verified that the aromatic moiety, sulfydryl group and amino group of BDOM affected the electronic supply and energy transfer. Higher electron and energy transfer favor the reaction of BDOM with the ground state oxygen to generate ROS, thus promoting photodegradation of TC. This study provides a new basis for better assessing the ecological risks of BDOM.

Evaporation-Induced Transformations in Volatile Chemical Product-Derived Secondary Organic Aerosols: Browning Effects and Alterations in Oxidative Reactivity.

Volatile chemical products (VCPs) are increasingly recognized as significant sources of volatile organic compounds (VOCs) in urban atmospheres, potentially serving as key precursors for secondary organic aerosol (SOA) formation. This study investigates the formation and physicochemical transformations of VCP-derived SOA, produced through ozonolysis of VOCs evaporated from a representative room deodorant air freshener, focusing on the effects of aerosol evaporation on its molecular composition, light absorption properties, and reactive oxygen species (ROS) generation. Following aerosol evaporation, solutes become concentrated, accelerating reactions within the aerosol matrix that lead to a 42% reduction in peroxide content and noticeable browning of the SOA. This process occurs most effectively at moderate relative humidity (∼40%), reaching a maximum solute concentration before aerosol solidification. Molecular characterization reveals that evaporating VCP-derived SOA produces highly conjugated nitrogen-containing products from interactions between existing or transformed carbonyl compounds and reduced nitrogen species, likely acting as chromophores responsible for the observed brownish coloration. Additionally, the reactivity of VCP-derived SOA was elucidated through heterogeneous oxidation of sulfur dioxide (SO2), which revealed enhanced photosensitized sulfate production upon drying. Direct measurements of ROS, including singlet oxygen (1O2), superoxide (O2•-), and hydroxyl radicals (•OH), showed higher abundances in dried versus undried SOA samples under light exposure. Our findings underscore that drying significantly alters the physicochemical properties of VCP-derived SOA, impacting their roles in atmospheric chemistry and radiative balance.

Innovative Bi5O7I/MIL-101(Cr) Compounds: A Leap Forward in Photocatalytic Tetracycline Removal.

In environmental chemistry, photocatalysts for eliminating organic contaminants in water have gained significant interest. Our study introduces a unique heterostructure combining MIL-101(Cr) and bismuth oxyiodide (Bi5O7I). We evaluated this nanostructure's efficiency in adsorbing and degrading tetracycline (TC) under visible light. The Bi5O7I@MIL-101(Cr) composite, with a surface area of 637 m2/g, prevents self-aggregation seen in its components, enhancing visible light absorption. Its photocatalytic efficiency surpassed Bi5O7I and MIL-101(Cr) by 33.4 and 9.2 times, respectively. Comprehensive analyses, including scanning electron microscopy (SEM) and transmission electron microscopy (TEM), confirmed the successful formation of the heterostructure with defined morphological characteristics. BET analysis demonstrated its high surface area, while X-ray diffraction (XRD) confirmed its crystallinity. Electron spin resonance (ESR) tests showed significant generation of reactive oxygen species (ROS) like h+ and·â€¢O2- under light, crucial for TC degradation. The material maintained exceptional durability over five cycles. Density functional theory (DFT) simulations and empirical investigations revealed a type I heterojunction between Bi5O7I and MIL-101(Cr), facilitating efficient electron-hole pair separation. This study underscores the superior photocatalytic activity and stability of Bi5O7I@MIL-101(Cr), offering insights into designing innovative photocatalysts for water purification.

Visible light triggers the formation of reactive oxygen species in monoclonal antibody formulations.

Most monoclonal antibody formulations require the presence of a surfactant, such as polysorbate, to ensure protein stability. The presence of high concentrations of polysorbate have been shown to enhance photooxidation of certain protein drug products when exposed to visible light. The current literature, however, suggest that photooxidation of polysorbate only occurs when exposed to visible light in combination with UVA light. This is probable as peroxides present in polysorbate solutions can be cleaved homolytically in the UVA region. In the visible region, photooxidation is not expected to occur as cleavage of peroxides is not expected at these wavelengths. This report presents findings suggesting that the presence of one or more photosensitiser(s) in polysorbate must be a cause and is required to catalyse the aerobic oxidation of polysorbate solutions upon exposure to visible light. Our investigation aimed to clarify the mechanism(s) of polysorbate photooxidation and explore the kinetics and the identity of the generated radicals and their impact on monoclonal antibody (mAb) degradation. Our study reveals that when polysorbate solutions are exposed to visible light between 400 - 800 nm in the absence of proteins, discolouration, radical formation, and oxygen depletion occur. We discuss the initial formation of reactive species, most likely occurring directly after reaction of molecular oxygen, with the presence of a triplet state photosensitiser, which is generated by intersystem crossing of the excited singlet state. When comparing the photooxidation of PS20 and PS80 in varying quality grades, we propose that singlet oxygen possesses potential for reacting with unsaturated fatty acids in PS80HP, however, PS20HP itself exhibited no measurable oxidation under the tested conditions. The study's final part delves into the photooxidation behaviour of different PS grades, examining its influence on the integrity of a mAb in the formulation. Finally, we examined the effect of photooxidation on the integrity of monoclonal antibodies. Our findings show that the exposure to visible light in polysorbate-containing mAb solutions at high PS concentrations of 4 mg·ml-1 results in increased monoclonal antibody degradation, highlighting the need for cautious evaluation of the correct PS concentration to stabilise protein therapeutics.

Electrocatalytic Generation of Singlet Oxygen via ROS-Mediated Redox Chain Reaction for Efficient Disinfection.

The risk of harmful microorganisms to ecosystems and human health has stimulated exploration of singlet oxygen (1O2)-based disinfection. It can be potentially generated via an electrocatalytic process, but is limited by the low production yield and unclear intermediate-mediated mechanism. Herein, we designed a two-site catalyst (Fe/Mo-N/C) for the selective 1O2 generation. The Mo sites enhance the generation of 1O2 precursors (H2O2), accompanied by the generation of intermediate •HO2/•O2-. The Fe site facilitates activation of H2O2 into •OH, which accelerates the •HO2/•O2- into 1O2. A possible mechanism for promoting 1O2 production through the ROS-mediated chain reaction is reported. The as-developed electrochemical disinfection system can kill 1 × 107 CFU mL-1 of E. coli within 8 min, leading to cell membrane damage and DNA degradation. It can be effectively applied for the disinfection of medical wastewater. This work provides a general strategy for promoting the production of 1O2 through electrocatalysis and for efficient electrochemical disinfection.

High-Resolution Mass Spectrometry Combined with Reactive Oxygen Species Reveals Differences in Photoreactivity of Dissolved Organic Matter from Microplastic Sources in Aqueous Environments.

Microplastics (MPs)-derived dissolved organic matter (MPs-DOM) is becoming a non-negligible source of DOM pools in aquatic systems, but there is limited understanding about the photoreactivity of different MPs-DOM. Herein, MPs-DOM from polystyrene (PS), polyethylene terephthalate (PET), poly(butylene adipate-co-terephthalate) (PBAT), PE, and polypropylene (PP), representing aromatic, biodegradable, and aliphatic plastics, were prepared to examine their photoreactivity. Spectral and high-resolution mass spectrometry analyses revealed that PS/PET/PBAT-DOM contained more unsaturated aromatic components, whereas PE/PP-DOM was richer in saturated aliphatic components. Photodegradation experiments observed that unsaturated aromatic molecules were prone to be degraded compared to saturated aliphatic molecules, leading to a higher degradation of PS/PET/PBAT-DOM than PE/PP-DOM. PS/PET/PBAT-DOM was mainly degraded by hydroxyl (•OH) via attacking unsaturated aromatic structures, whereas PE/PP-DOM by singlet oxygen (1O2) through oxidizing aliphatic side chains. The [•OH]ss was 1.21-1.60 × 10-4 M in PS/PET/PBAT-DOM and 0.97-1.14 × 10-4 M in PE/PP-DOM, while the [1O2]ss was 0.90-1.35 × 10-12 and 0.33-0.44 × 10-12 M, respectively. This contributes to the stronger photoreactivity of PS/PET/PBAT-DOM with a higher unsaturated aromatic degree than PE/PP-DOM. The photodegradation of MPs-DOM reflected a decreasing tendency from aromatic-unsaturated molecules to aliphatic-saturated molecules. Special attention should be paid to the photoreactivity and environmental impacts associated with MPs-DOM containing highly unsaturated aromatic compounds.

Ba2+-doping introduced piezoelectricity and efficient Ultrasound-Triggered bactericidal activity of brookite TiO2 nanorods.

Exploring highly efficient ultrasound-triggered catalysts is pivotal for various areas. Herein, we presented that Ba2+ doped brookite TiO2 nanorod (TiO2: Ba) with polarization-induced charge separation is a candidate. The replacement of Ba2+ for Ti4+ not only induced significant lattice distortion to induce polarization but also created oxygen vacancy defects for facilitating the charge separation, leading to high-efficiency reactive oxygen species (ROS) evolution in the piezo-catalytic processes. Furthermore, the piezocatalytic ability to degrade dye wastewater demonstrates a rate constant of 0.172 min-1 and achieves a 100 % antibacterial rate at a low dose for eliminating E. coli. This study advances that doping can induce piezoelectricity and reveals that lattice distortion-induced polarization and vacancy defects engineering can improve ROS production, which might impact applications such as water disinfection and sonodynamic therapy.

Insights into the Crystallinity-Dependent Photochemical Productions of Reactive Oxygen Species from Iron Minerals.

Iron minerals are widespread in earth's surface water and soil. Recent studies have revealed that under sunlight irradiation, iron minerals are photoactive on producing reactive oxygen species (ROS), a group of key species in regulating elemental cycling, microbe inactivation, and pollutant degradation. In nature, iron minerals exhibit varying crystallinity under different hydrogeological conditions. While crystallinity is a known key parameter determining the overall activity of iron minerals, the impact of iron mineral crystallinity on photochemical ROS production remains unknown. Here, we assessed the photochemical ROS production from ferrihydrites with different degrees of crystallinity. All examined ferrihydrites demonstrated photoactivity under irradiation, resulting in the generation of hydrogen peroxide (H2O2) and hydroxyl radical (•OH). The photochemical ROS production from ferrihydrites increased with decreasing ferrihydrite crystallinity. The crystallinity-dependent photochemical •OH production was primarily attributed to conduction band reduction reactions, with the reduction of O2 by conduction band electrons being the rate-limiting key process. Conversely, the crystallinity of iron minerals had a negligible influence on photon-to-electron conversion efficiency or surface Fenton-like activity. The difference in ROS productions led to a discrepant degradation efficiency of organic pollutants on iron mineral surfaces. Our study provides valuable insights into the crystallinity-dependent ROS productions from iron minerals in natural systems, emphasizing the significance of iron mineral photochemistry in natural sites with abundant lower-crystallinity iron minerals such as wetland water and surface soils.

Kinetics of ascorbate and dithiothreitol oxidation by soluble copper, iron, and manganese, and 1,4-naphthoquinone: Influence of the species concentration and the type of fluid.

An alternative metric to account for particulate matter (PM) composition-based toxicity is the ability of PM-species to generate reactive oxygen species (ROS) and deplete antioxidants, the so-called oxidative potential (OP). Acellular OP assays are the most used worldwide, mainly those based on ascorbic acid (AA) and dithiothreitol (DTT) depletion; OP values are calculated from AA/DTT concentration over time kinetic curves. Since a great variability in OP-DTT and OP-AA values can be found in the literature, the understanding of those factors affecting the kinetic rate of AA and DTT oxidation in the presence of PM-bound species will improve the interpretation of OP values. In this work, a kinetic study of the oxidation rate of AA and DTT driven by species usually found in PM (transition metals and naphthoquinone (NQ)) was carried out. In particular, the influence of the concentration of Cu(II), Fe(II), Fe(III), Mn(II), Mn(III), and 1,4-NQ, and the type of fluid used in the assay (phosphate buffer (PB), phosphate buffer saline (PBS) and artificial lysosomal fluid (ALF)) is analysed and discussed. The reaction orders with respect to the AA/DTT and the active compound, and the kinetic rate constants were also determined. The results show great variability in OP values among the studied species depending on the fluid used; the OP values were mostly higher in PB0.05 M, followed by PBS1x and ALF. Moreover, different species concentration-responses for OP-DTT/OP-AA were obtained. These differences were explained by the different reaction orders and kinetic rate constants obtained for each active compound in each fluid.

Mechanistic Insights into the Antioxidant and Pro-oxidant Activities of Bromophenols from Marine Algae: A DFT Investigation.

Marine algae are a rich source of aromatic secondary metabolites, with bromophenols (BPs) receiving particular attention due to their health benefits. Despite extensive research on BPs, the understanding of their antioxidant potential, as well as their mechanisms of action at the molecular level, remains incomplete. This study utilized density functional theory (DFT) to systematically elucidate the antioxidant and pro-oxidant mechanisms of the main BP scaffolds under physiological conditions. It was found that BPs exhibit potent antioxidant capacity in both polar and lipid environments. In lipid media, the formal hydrogen transfer mechanism has been identified as the exclusive antiradical pathway. The position of bromine atoms significantly influenced the activity, particularly in scaffolds containing one hydroxyl group. However, no significant effect was observed in scaffolds with two hydroxyl groups. In water, monodeprotonated BPs showed key radical scavenging activity, with different mechanisms favored depending on the configuration of the hydroxyl groups. Additionally, BPs, particularly those bearing a catechol moiety, exhibit secondary antioxidant activity by reducing the production of hydroxyl radicals via the ascorbic acid anion pathway. These findings provide further validation of the potent antioxidant properties of BPs and shed light on their mechanism of action in physiological environments.

Degradation of tetracycline under a wide pH range in a heterogeneous photo bio-electro-fenton system using FeMn-LDH/g-C3N4 cathode: Performance and mechanism.

The widespread use of antibiotics and the inefficiency of traditional degradation treatments pose threats to the environment and human health. Previous studies have reported the potential of bio-electro-Fenton (BEF) processes for antibiotic removal. However, some drawbacks, such as a strict pH range of 2-3 and iron sludge generation, limit their large-scale application. Thus, to overcome the narrow pH range of traditional BEF processes, a photo-BEF (PBEF) system was established using a novel FeMn-layered double hydroxide (LDH)/graphitic carbon nitride (g-C3N4) (FM/CN) composite cathode. The performance of the PBEF system was investigated by degrading tetracycline (TC) under low-power LED lamp irradiation. The results indicated that the pH range of the PBEF system could be expanded to 3-11 using an FM/CN cathode, which exhibited a TC removal efficiency of 63.0%-75.9%. The highest TC removal efficiency was achieved at pH 7. The efficient mineralization of TC by the PBEF system can be high, up to 67.6%. In addition, the TC removal mechanism was discussed in terms of reactive oxygen species, TC degradation intermediate analyses, and density functional theory (DFT) calculations. Strong oxidative hydroxyl radicals (·OH) were the dominant reactive oxidizing species in the PBEF system, followed by ·O2- and h+. Three pathways of TC degradation were proposed based on the analysis of intermediates, and the reactive sites attacked by electrophilic reagents were explored using DFT modeling. In addition, the overall toxicity of TC degradation intermediates effectively decreased in the PBEF system. This work offers deep insights into the TC removal mechanisms and performance of the PBEF system over a wide pH range of 3-11.

Ferromanganese oxide-functionalized TiO2 for rapid catalytic ozonation of PPCPs through a coordinated oxidation process with adjusted composition and strengthened generation of reactive oxygen species.

Ferromanganese oxide (MFOx) was first utilized to functionalize TiO2 and an MFOx@TiO2 catalyst was developed for catalytic ozonation for rapid attack of pharmaceutical and personal care products (PPCPs) with adjusted reactive oxygen species (ROSs) composition and strengthened ROSs generation. Unlike Al2O3, which strongly relied on adsorption and was significantly influenced by MFOx loading, synergistic catalytical effects of MFOx and TiO2 were observed, and optimal MFOx doping of 2 wt% and MFOx@TiO2 dosage of 500 ppm were obtained for catalyzing ozonation. In ibuprofen (IBP) degradation, MFOx@TiO2-catalyzed ozonation (MFOx@TiO2/O3) obtained 2.0-, 4.7- and 6.9-folds the kobs of TiO2/O3, MFOx/O3 and bare ozonation (B/O3). Stronger O3 decomposition was observed by MFOx@TiO2 over bare TiO2 with the participation of redox pairs Fe(II)/Fe(III) and Mn(II)/Mn(III)/Mn(IV) and increased surface oxygen vacancies (SOVs) from 9.8 % to 33.7 % was detected. The results revealed that Fe(II), Mn(II) and Mn(III) with low valance accelerated Ti(III) generation from Ti(VI), obtaining an unprecedented high Ti(III) composition occupying 35.3 % of the total Ti atoms. Ti(III) catalyzed the direct reduction of SOVs-O2 to •O2-, and it accelerated the formation of Ti(VI)-OH and Ti(VI)-O which catalyzed O3 decomposition into •O2-. •O2- was found to primarily initiate IBP degradation with nucleophilic addition and dominated over 66 % IBP removal. The enhanced •O2- generation further strengthened •OH and 1O2 production. MFOx@TiO2/O3 obtained 17 %, 21 % and 30 % higher TOC removal over TiO2/O3, MFOx/O3 and B/O3, respectively. Acute toxicity tests confirmed the effective toxicity control of organics by MFOx@TiO2/O3 process (inhibition rate: 10.9 %). Degradation test of atenolol and sulfamethoxazole confirmed the catalytic effects of MFOx@TiO2. MFOx@TiO2 performed strong resistance to water matrix in application test and showed good stability and reusability. The study proposed an effective catalyst for strengthening the ozonation process on PPCPs degradation and provided an in-depth understanding of the mechanisms and characteristics of the MFOx@TiO2 catalyst and MFOx@TiO2/O3 process.

Activating peroxymonosulfate with Fe-doped biochar for efficient removal of tetracycline: Dual action of reactive oxygen species and electron transfer.

If pharmaceutical wastewater is not managed effectively, the presence of residual antibiotics will result in significant environmental contamination. In addition, inadequate utilization of agricultural waste represents a squandering of resources. The objective of this research was to assess the efficacy of iron-doped biochar (Fe-BC) derived from peanut shells in degrading high concentrations of Tetracycline (TC) wastewater through activated peroxymonosulfate. Fe-BC demonstrated significant efficacy, achieving a removal efficiency of 87.5% for TC within 60 min without the need to adjust the initial pH (20 mg/L TC, 2 mM PMS, 0.5 g/L catalyst). The degradation mechanism of TC in this system involved a dual action, namely Reactive Oxygen Species (ROS) and electron transfer. The primary active sites were the Fe species, which facilitated the generation of SO4•-, •OH, O2•-, and 1O2. The presence of Fe species and the C=C structure in the Fe-BC catalyst support the electron transfer. Degradation pathways were elucidated through the identification of intermediate products and calculation of the Fukui index. The Toxicity Estimator Software Tool (T.E.S.T.) suggested that the intermediates exhibited lower levels of toxicity. Furthermore, the system exhibited exceptional capabilities in real water and circulation experiments, offering significant economic advantages. This investigation provides an efficient strategy for resource recycling and the treatment of high-concentration antibiotic wastewater.

Constructing Interfacial Charge Transfer Channels and Electric Field in Violet Phosphorus-Based van der Waals Heterojunction for Phototherapy of Periodontitis.

Periodontitis, a chronic oral disease instigated by bacteria, severely compromises human oral health. The prevailing clinical treatment for periodontitis involves mechanical scraping in conjunction with antibiotics. Phototherapy is employed to rapidly remove the bacteria and achieve periodontitis treatment, effectively circumventing the adverse effects associated with traditional therapies. Constructing 2D/2D van der Waals (VDW) heterojunctions is a key strategy for obtaining excellent photocatalytic activity. Herein, a 2D/2D violet phosphorus (VP)/Ti3C2 VDW heterojunction is designed using an interfacial engineering strategy. By constructing an electron transport "bridge" (P-Ti bond) at the heterogeneous interface as an effective transfer channel for photogenerated carriers, a compact monolithic structure between the VP and Ti3C2 phases is formed, and the spatial barrier for electron transfer at the interface is eliminated. Meanwhile, the strong directional built-in electric field induced by the intensive electron-coupling effect at the heterogeneous interface served as an internal driving force, which greatly accelerates the exciton dissociation and charge transfer in the photocatalytic process. These excited photogenerated electrons and holes are trapped by O2 and H2O on the surfaces of Ti3C2 and VP, respectively, and are subsequently catalytically converted to antibacterial reactive oxygen species (ROS). The VP/Ti3C2 VDW heterojunction eradicated 97.5% and 98.48% of Staphylococcus aureus and Escherichia coli, respectively, by photocatalytic and photothermal effects under visible light for 10 min. The VP/Ti3C2 nanoperiodontal dressing ointment effectively attenuated inflammatory response, reduced alveolar bone resorption, and promoted periodontal soft and hard tissue repair. Its periodontitis therapeutic effect outperforms the clinically used Periocline.

Frustrated Lewis pairs created by Ce-doped Bi2MoO6: A universal strategy to promote efficient utilization of H2O2 for Fenton-like photodegradation.

Photo-Fenton-like technology based on H2O2 is considered as an ideal strategy to generate reactive oxygen species (ROS) for antibiotic degradation, but O2 overflow in the process severely limits the utilization efficiency of H2O2. Herein, we fabricate Bi2MoO6 (BMO) photocatalyst modified with Frustrated Lewis pairs (FLPs) as a Fenton catalyst model for enhancing reuse of spilled O2. The FLPs created by the introduction of cerium and oxygen vacancy were found to contribute to regulate the electronic structure of BMO and further improve the acidic and basic properties of photocatalyst surface. More importantly, the frustrated acid and base sites can enhance the H2O2 and O2 interfacial adsorption process and provide an Ce4+-Ov-O2- active site on the surface of Ce-BMO nanosheets, which can promote O2/•O2-/1O2/H2O2 redox cycles to achieve high H2O2 utilization efficiency. Specifically, in the experiment using tetracycline as a photocatalytic degradation object, the degradation activity of Ce-BMO was 2.15 times higher than that of BMO pure phase. Quenching experiments and EPR assays also confirmed that 1O2 and •O2- were the dominant oxidative species. This study systematically reveals the design of Fenton photocatalytic active sites at the atomic scale and provides new insights into constructing FLPs photocatalysts with high H2O2 utilization efficiency.