Mini-Open Dumps in the Paraná River Floodplain: Local Problems with Global Effects.

The growing production of urban solid waste is a structural problem faced by most cities around the world. The proliferation of mini-open dumps (MOD; small spontaneous open-air waste dumps formed in urban and peri-urban areas) on the banks of the Paraná River is particularly evident. During the historical drought (June-December 2021), we carried out sampling campaigns identifying MODs of the Santa Fe River, a secondary channel of the Paraná River. MOD were geolocated, measured, described and classified by origin. The distance to the river and other sensitive places was considered (houses-schools-health facilities). Our results suggested a serious environmental issue associated with poor waste management. MOD were extremely abundant in the study area, being mostly composed of domestic litter. Plastics clearly dominated the MOD composition. Burning was frequently observed as a method to reduce the volume of MOD. We concluded that the proliferation of MOD is a multi-causal problem associated with a failure of public policies and a lack of environmental education.

Strontium leaching from municipal waste subjected to incineration.

The aim of the study was to determine the content and leachability of Sr in ashes obtained through combusting municipal waste in household furnaces. The waste had been collected as a mixed stream and as separate fractions (i.e. furniture, sponges, waste paper, PCV packaging, plastic-coated paper cartons, imitation leather, rubber, textiles and polystyrene). Using single-step chemical extractions, (HCl + HNO3, H2O, 0.01 M CaCl2, 0.1 M CH3COOH), we determined the total content of Sr (TC) and proportions of the following fractions: water-leachable, phytoavailable and easily soluble and bound to carbonates. We also analyzed the effect of reducing pH in the extraction solutions on St leachability from the study material. The study showed that Sr concentration in ash generated from the combustion of conventional fuels, alternative fuels and municipal waste ranged from 114 to 1006 mg/kg. The largest amounts of Sr were found in ash generated from the combustion of alternative fuels (coal pellets 488-1006 mg/kg), conventional fuels (hard coal 430-670 mg/kg) and mixed waste (237-825 mg/kg). The most mobile fraction of Sr (water-leachable) comprised from 1.3% to nearly 91% TC; the phytoavailable fraction and the ion-exchange and carbonate-bound fraction comprised 3-92% TC and 9-72% TC, respectively. We also found that the greatest pH reductions do not always entail the greatest amounts of extracted Sr. A much more significant factor in this respect is the mineral and chemical composition of primary materials, which can buffer changes in pH. The Risk Assessment Code (RAC) values pointed to a varied environmental risk and the highest RAC values (> 70) were found for coal pellets, wood pellets, straw, rubber and plastic containers for mixed oils.

New insight into the spatio-temporal patterns of functional groups of hotspot inside the composting aggregates by synchrotron-based FTIR in hyperthermophilic composting.

Hyperthermophilic composting (HTC) is a recently developed and highly promising organic fraction of municipal solid waste (OFMSW) treatment technology. Investigation of organic matter (OM) dynamics in compost particle is thus crucial for the understanding of humification of HTC process. Herein, this work aimed to study the chemical and structural changes of OM at the molecular level during HTC of OFMSW using EEM and SR-FTIR analyses. Additionally, two-dimensional correlation spectroscopy (2D-COS) was also utilized to probe and identify the changes in chemical constituents and functional groups of organic compounds on the surface of compost particles during different composting periods. Results show that SR-FTIR can detect fine-scale (~µm) changes in functional groups from the edges to the interior of compost particles during different composting periods by mapping the particles in situ. In the hyperthermophilic stage (day 9), the extracted µ-FTIR spectrum reveals a distinct boundary between anaerobic and aerobic regions within the compost particle, with a thickness of anaerobic zone (1460 cm-1) of approximately 30 µm inside the particle's core. This provides direct evidence of anaerobic trends at compost microscales level within compost particles. 2D-COS analysis indicated that organic functional groups gradually agglomerated in the order of 1330 > 2930 > 3320 > 1600 > 1030 > 895 cm-1 to the core skeleton of cellulose degradation residues, forming compost aggregates with well physicochemical properties. Overall, the first combination of SR-FTIR and EEM provides complementary explanations for the humification mechanism of HTC, potentially introducing a novel methodology for investigating the environmental behaviors and fates of various organic contaminants associated with OM during the in-situ composting biochemical process.

Quantification and polymeric characterization of microplastics in composts and their accumulation in lettuce.

Organic fertilizers have become a vector for the transport of microplastics (MPs), which pose human health concerns through the food chain. This study aimed to quantify and characterize MPs in eight different compost samples of various raw materials and their subsequent translocation to lettuce (Lacuta sativa) grown on contaminated composts. The results revealed that the MP abundance ranged from 3810 to 16530 MP/kg. Municipal solid waste compost (MSWC) had highest abundance (16082 ± 632 MP/kg), followed by leaf compost (LC) and organic compost (OC) (6299 ± 1011 and 3680 ± 419 MP/kg, respectively). MPs of <100 µm in size were most dominant in MSWC and LC. Fragments and fibers were the prevalent shape types, with white/transparent colored MPs being more abundant. Polyethylene (PE), polypropylene (PP) and polyethylene terephthalate (PET) were the dominant polymers. MPs accumulation in the lettuce leaves was greatest in the lettuce plants grown on MSWC, followed by those grown on LC and OC, indicating that MSWC grown lettuce is not suitable for human consumption. The decrease in the growth (leaf length, number of leaves, leaf fresh and weights) and physiological (membrane stability index, relative water contents) parameters of lettuce was in line with the trend of MP accumulations. Hence, it is highly important to regulate the plastic contents in compost because it is a threat to ecosystems and human health.

[Effects of Fly Ash on the Efficiency and Bacterial Community Structure of Urban Multi-source Organic Solid Waste].

To achieve efficient resource utilization of fly ash and multi-source organic waste, a composting experiment was carried out to investigate the effects of fly ash on co-aerobic composting using kitchens, chicken manure, and sawdust (15:5:2). The effects of different application doses (5 % and 10 %, calculated in total wet weight of organic solid waste) of fly ash on physical and chemical properties, nutrient elements, and bacterial community structure during co-composting were evaluated. The results showed that the addition dose of 5 % and 10 % fly ash significantly increased the highest temperature (56.6 ℃ and 56.9 ℃) and extended the thermophilic period to nine days. Compared with that in the control, the total nutrient content of compost products in the treatments of 5 % FA and 10 % FA was increased by 4.09 % and 13.55 %, respectively. The bacterial community structure changed greatly throughout the composting, and the bacterial diversity of all treatments increased obviously. In the initial stage of composting, Proteobacteria was the dominant phylum of bacteria, with a relative abundance ranging from 35.26 % to 39.40 %. In the thermophilic period, Firmicutes dominated; its relative abundance peaked at 52.46 % in the 5 % FA treatment and 67.72 % in the 10 % FA treatment. Bacillus and Thermobifida were the predominant groups in the thermophilic period of composting. The relative abundance of Bacillus and Thermobifida in the 5 % FA and 10 % FA treatments were 33.41 % and 62.89 %(Bacillus) and 33.06 % and 12.23 %(Thermobifida), respectively. The results of the redundancy analysis (RDA) revealed that different physicochemical indicators had varying degrees of influence on bacteria, with organic matter, pH, available phosphorus, and available potassium being the main environmental factors influencing bacterial community structure. In summary, the addition of fly ash promoted the harmlessness and maturation of co- aerobic composting of urban multi-source organic waste, while optimizing microbial community structure and improving the quality and efficiency of composting.

Evolution of physicochemical and leaching characteristics of municipal solid waste incineration fly ash in China under ultra-low emission standard.

The physical and chemical characteristics of fly ash has changed significantly under ultra-low emission system and the current leaching system is no longer suitable for high alkalinity fly ash. This work investigated the pH values and evolution of physical and chemical characteristics of fly ash from 24 typical municipal solid waste incineration plants in China. The pH value of the leaching solution obtained by HJ/T 300-2007 presented two different acid and alkali characteristics, where high and low alkalinity fly ash accounted for 54.17% and 45.83%, respectively. The alkali content in fly ash increased significantly after ultra-low emission standard, increasing by 18.24% compared with before the implementation of GB 18485-2014. The leaching behavior of high alkalinity fly ash showed the illusion that they could enter the landfill only by the addition of a small amount of chelating agent or even without stabilization treatment, and its long-term landfill risk is significant. The phase change of high alkalinity fly ash and pH value change of the leaching solution after carbonation were the key factors for the leaching concentration change of heavy metals. Therefore, it is recommended to improve the existing leaching system or conduct accelerated carbonization experiments to scientifically evaluate the long-term leaching characteristics of high alkalinity fly ash, and to reduce the risk of heavy metal release from high alkalinity FA after entering the landfill site.

Not only in the crowd: Benthic litter characterization in a low population density area still reveals widespread pollution and local malpractices.

Various anthropogenic activities affect marine coastal habitats, leading to heavy litter pollution. However, whilst high litter concentrations are nowadays common in the proximity of metropolises, few studies investigated the magnitude of this phenomenon around coastal villages and small towns. We hereby characterized the benthic litter occurring in the trawlable grounds of the Gulf of Policastro (Tyrrhenian Sea, central-western Mediterranean), a low population density area that becomes a popular tourist destination during summer. We furthermore tested differences between two depths (∼100-200 and ∼500-600 m) and the impact of tourism on the shallower waters. The area was characterized by a litter abundance of 651.12 ± 130.61 item/km2, with plastic being almost totalitarian (93%). The shallower waters hosted two-thirds of the litter found. Almost all (∼95%) the litter items had a land-based origin, while the sea-based litter was mostly found at higher depths. About 14% of the litter was found to be fouled, with the development of litter-associated communities that somehow mimic the natural ones living on hard substrates. The higher litter presence noticed during the touristic peak (July-August) suggests that tourism is an important source of local litter, although it contributed to the local accumulation in a synergic way with other factors. The majority of the litter items presumably originated from the nearby coastline, while the deeper waters were or are used as a dumping site by the local trawling fleet. The discovery of such a critical waste accumulation and management in a somehow remote area contributes to widen the perspectives on the presence of benthic litter mostly in territories characterized by wide anthropization. Moreover, it confirms that appropriate local policies and communication plans are urged even at a regional level to stimulate citizen consciousness and mitigate the ever growing litter pollution.

Integrating fuzzy-AHP and GIS for solid waste disposal site selection in Kenitra province, NW Morocco.

Selecting an optimal solid waste disposal site is one of the decisive waste management issues because unsuitable sites cause serious environmental and public health problems. In Kenitra province, northwest Morocco, sustainable disposal sites have become a major challenge due to rapid urbanization and population growth. In addition, the existing disposal sites are traditional and inappropriate. The objective of this study is to suggest potential suitable disposal sites using fuzzy logic and analytical hierarchy process (fuzzy-AHP) method integrated with geographic information system (GIS) techniques. For this purpose, thirteen factors affecting the selection process were involved. The results showed that 5% of the studied area is considered extremely suitable and scattered in the central-eastern parts, while 9% is considered almost unsuitable and distributed in the northern and southern parts. Thereafter, these results were validated using the area under the curve (AUC) of the receiver operating characteristics (ROC). The AUC found was 57.1%, which is a moderate prediction's accuracy because the existing sites used in the validation's process were randomly selected. These results can assist relevant authorities and stakeholders for setting new solid waste disposal sites in Kenitra province.

Critical properties of plastic packaging waste for recycling: A case study on non-beverage plastic bottles in an urban MSW system in Austria.

The low recycling rate of post-consumer plastic packaging waste (PPW), which is partly due to insufficient separate collection, heterogeneous composition and high levels of contamination, poses a challenge in Austria, where the recycling rate must double in order to meet the target of 55 %. This study analyzes key packaging characteristics of non-beverage plastic bottles influencing recyclability, using Vienna as a case study. Additionally, a net quantity indicator and separate collection rates were calculated. 738 bottles from mixed MSW and 1,159 bottles from separate PPW collection were analyzed. The main polymer's proportion described by the net quantity indicator was higher for bottles from separate collection (69-72 %) than from mixed MSW (58 %), showing that a large share of the foreign materials are residues and dirt, with significantly higher contents in mixed MSW (20 %) than in separate collection (11 %). With a separate collection rate of 19.2 %, the great potential for recycling currently lies in mixed MSW at 4,112 t/yr. Thereof, 46 % is uncolored, 54 % is colored/white and, in terms of material grade, 30 % is food grade. The most common filling volume for PET, PP and HDPE was 0.5 < x ≤ 1.5 L (23-59 %) and the most common decoration technology was label (60-85 %). PET and PP had the highest shares of food-grade bottles (37-46 %), while PP had the highest share of colored bottles (22-31 %). The mechanical recycling potential of bottles depends largely on packaging characteristics, influencing separate collection and also automatic sorting. Harmonized design specifications are therefore crucial for this heterogeneous PPW fraction.

Higher heating value estimation of wastes and fuels from ultimate and proximate analysis by using artificial neural networks.

Higher heating value (HHV) is one of the most important parameters in determining the quality of the fuels. In this study, comparatively large datasets of ultimate and proximate analysis are constructed to be used in HHV estimation of several classes of fuels, including char & fossil fuels, agricultural wastes, manure (chicken, cow, horse, sheep, llama, and pig), sludge (like paper, paper-mil, sewage, and pulp), micro/macro-algae's, wastes (RDF and MSW), treated woods, untreated woods, and others (non-fossil pyrolysis oils) between the HHV range of 4.22-55.55 MJ/kg. The relationships of carbon, hydrogen, and oxygen atomic ratios for fuel classes are illustrated by using ternary plots, and the effects of elemental composition on HHV was analyzed with the extensive dataset. Then, the ultimate (U) and ultimate & proximate (UP) datasets were utilized separately to estimate the HHV by using artificial neural networks (ANN). Hyperparameter optimization was carried out and the best performing ANNs were determined for each dataset, which yielded R2 values of 0.9719 and 0.9715, respectively. The results indicated that while ANNs trained by both datasets perform remarkably well, utilization of U dataset is sufficient for HHV estimation. Finally, the best performing ANN models for both U and UP datasets are given in a directly utilizable format enabling the accurate estimation of HHV of any fuel for optimization of fuel processing and waste management operations.

Mechanical properties of municipal solid waste under different stress paths: Effects of plastic content and particle gradation.

Plastics within municipal solid waste (MSW) are non-degradable. As MSW continues to degrade, the relative content of plastics rises, and particle gradation may also change. Moreover, throughout the landfilling process, MSW is subjected to various stress conditions, potentially influencing its mechanical properties. This study explored the effects of varying plastic contents, different particle gradations, and distinct stress paths on the mechanical properties of MSW, and consolidated drained triaxial tests of 42 groups of reconstituted MSW specimens were conducted. The results showed that there was an optimal plastic content of 6-9 % for MSW, where the shear strength of MSW was higher than that of MSW with other plastic contents. When the stress path changed from TC45 to TC72, the optimal plastic content of MSW changed from 6 % to 9 %. As the plastic content increased, both the cohesion and internal friction angle of the MSW initially increased, then subsequently decreased. The impact of plastic content on cohesion was more pronounced than on the internal friction angle, especially at larger strains. Under various stress paths, MSW with distinct particle size distributions demonstrated diverse stress-strain behaviors. Traditional criteria for evaluating well-graded conditions in soils are not suitable for MSW. The effect of gradation on the cohesion of MSW is essentially due to the predominant role of fiber content; the relationship between gradation and the internal friction angle in MSW is complex and correlates closely with the content of both coarse and fine particles, as well as fibers. This study serves as an essential reference for predicting deformations in landfills and analyzing the stability of landfill slopes.

Simultaneous achievement of energy recovery and carbon sequestration through municipal solid waste management: A review.

Effective municipal solid waste (MSW) management is a crucial component for sustainable cities, as inefficient waste disposal contributes to the release of about a billion tons of CO2-eq in greenhouse gases (GHG) annually. With escalating global waste generation, there is an untapped opportunity to integrate carbon dioxide removal (CDR) technologies into existing MSW management processes. This review explores current research on utilizing MSW for CDR, emphasizing its potential for both energy generation and carbon sequestration. The investigation covers three waste management practices: landfilling, waste-to-energy (WtE), and biochar production, revealing two paths for carbon sequestration. First, MSW serves as a feedstock in bioenergy with carbon capture and storage (BECCS), acting as a carbon-neutral resource that avoids fossil fuel and energy crop use, reducing GHG emissions and generating value through energy production. Second, direct storage of organic MSW and its derivatives, like biochar, in various carbon sinks allows for extended sequestration, offering a comprehensive approach to address the challenges of waste management and climate change mitigation. Moreover, this review advocates for an extended exploration into several subjects including in-depth analysis of waste, research on MSW-derived biochar recalcitrance across different carbon sinks, and understanding the symbiotic connections with GHG-emitting sectors like agriculture and energy. Finally, this review emphasizes the necessity of conducting life-cycle assessment studies to fully discern the benefits and assess the impacts of any future endeavors exploring the role of MSW in carbon sequestration.

Modeling risk assessment of soil heavy metal pollution using partial least squares and fuzzy logic: A case study of a gully type coal-based solid waste dumpsite.

Continuous release and migration of heavy metals from coal-based solid waste (CSW) dumpsites often results in significant encroachment on ecological lands and pollution of natural environments. As a result, there is an urgent need for long-term and rapid monitoring, analysis, and assessment to control environmental risks associated with large CSW dumpsites. We constructed a new composite model (PLS-FL) that uses partial least squares regression (PLSR) and fuzzy logic inference (FLI) to accurately predict heavy metal concentrations in soils and assess pollution risk levels. The potential application of the PLS-FL was tested through a gully type CSW case study. We compared 20 modeling strategies using the PLS-FL: five types heavy metals (Cd, Zn, Pb, Cr and As) * four spectral transformation methods (first derivative (FD), second derivative (SD), reverse logarithm (RL), and continuum removal (CR)) * one variable selection method (competitive adaptive reweighted sampling (CARS)). The results showed that the combination of derivative transformation and CARS was recommended for estimation, with R2C > 0.80 and R2P > 0.50. When comparing the PLSR model with four traditional machine learning methods (Support Vector Machines (SVM), Random Forests (RF), Extreme Learning Machines (ELM), and KNN), the PLSR model demonstrated the highest average prediction accuracy. Additionally, the FLI process no longer relies on human perception and expert opinion, enhancing the model's objectivity and reliability. The evaluation results revealed that the heavy metal contamination areas of the CSW dumpsite are concentrated at the bottom of the gully, with more severe contamination in the north. Furthermore, a high-risk zone exists in the interim storage area for CSW to the east of the dump. These findings align with the initial detections at the sampling sites and highlight the need for targeted monitoring and control in these areas. The application of the model will empower regulators to quickly assess the overall situation of large-scale heavy metal pollution and provide scientific program and data support for continuous large-scale pollution risk monitoring and sustainable risk management.

Synergistic utilization of industrial solid wastes: Extraction of valuable metals from tungsten leaching residue by photovoltaic sawing waste.

Solid waste challenges in both the tungsten and photovoltaic industries present significant barriers to achieving carbon neutrality. This study introduces an innovative strategy for the efficient extraction of valuable metals from hazardous tungsten leaching residue (W-residue) by leveraging photovoltaic silicon kerf waste (SKW) as a silicothermic reducing agent. W-residue contains 26.2% valuable metal oxides (WO3, CoO, Nb2O5, and Ta2O5) and other refractory oxides (SiO2, TiO2, etc.), while micron-sized SKW contains 91.9% Si with a surface oxide layer. The impact of SKW addition on the silicothermic reduction process for valuable metal oxides in W-residue was investigated. Incorporating SKW and Na2CO3 flux enables valuable metal oxides from W-residue to be effectively reduced and enriched as a valuable alloy phase, with unreduced refractory oxides forming a harmless slag phase during the Na2O-SiO2-TiO2 slag refining process. This process achieved an overall recovery yield of valuable metals of 91.7%, with individual recovery yields of W, Co, and Nb exceeding 90% with the addition of 8 wt.% SKW. This innovative approach not only achieves high-value recovery from W-residue and utilization of SKW but also minimizes environmental impact through an efficient and eco-friendly recycling pathway. The strategy contributes significantly to the establishment of a resource-efficient circular economy, wherein the recovered high-value alloy phase return to the tungsten supply chain, and the harmless slag phase become raw materials for microcrystalline glass production.

A picture of pharmaceutical pollution in landfill leachates: Occurrence, regional differences and influencing factors.

Municipal solid waste (MSW) landfill sites have been identified as a significant source of pharmaceuticals in the environment because unused or expired pharmaceuticals are discarded into MSW, which eventually percolate into leachates. However, the contamination of pharmaceuticals in landfill leachate in China is not comprehensively understood. Previous research into factors influencing pharmaceutical concentrations focused on a limited number and type of target pollutants or restricted study area. In the present study, 66 pharmaceuticals were analyzed (including 45 antibiotic and 21 non-antibiotic pharmaceuticals, also categorized as 59 prescription and 7 non-prescription pharmaceuticals) in leachate samples from landfill sites with various characteristics in different regions of China. The results indicated that non-antibiotic pollutants were present at significantly higher concentrations than antibiotic pollutants, with median concentrations of 1.74 µg/L and 527 ng/L, respectively. Non-antibiotic pollutants also presented a higher environmental risk than antibiotic pollutants, by 2 to 4 orders of magnitude, highlighting that non-antibiotic pharmaceuticals should not be overlooked during the assessment of landfill leachate. Pharmaceutical concentrations in landfill leachate samples exhibited regional differences; the population size served by the landfills was the dominant factor contributing to the observed differences. In addition, landfill characteristics such as the solid waste composition and MSW loading can also affect pharmaceutical concentrations in landfill leachate. Despite the implementation of the classification and disposal policy of MSW in Shanghai, China since July 2019, specifying that unused or expired pharmaceuticals should be discarded as hazardous waste, high levels of pharmaceutical contaminations were detected in leachate from the main components of classified MSW (i.e., residual and food waste). These findings emphasize the importance of pharmaceutical management in solid waste systems.

Complementary vitrification of municipal solid waste incineration fly ash from grate furnaces and fluidised bed incinerators via a co-reduction process.

The increasing application of municipal solid waste incineration (MSWI) emphasises the need for MSWI fly ash (FA) safe treatment. Based on the compositional complementarity of FA from grate furnaces (G-FA) and fluidised bed incinerators (F-FA), we proposed a co-reduction process to treat G-FA and F-FA together for producing vitrified slag and ferroalloys. The clean vitrified slag and Fe-Cr-Ni-Cu alloy were obtained with the mass ratios of 1:9 âˆ¼ 6:4 (G-FA:F-FA) at 1300℃, which is about 300℃ lower than the conventional G-FA vitrification. The metals Zn, Cd, and Pb were mostly volatilised into the flue gas for potential recovery from the secondary FA. The thermodynamic SiO2-Al2O3-CaO ternary system demonstrated that an optimal mass ratio of the two complementary FA types contributes to the system shifting to the low-temperature melting zone. The co-reduction process of G-FA and F-FA could be a promising option for FA beneficial reutilization with environmental advantages.

Dynamic release of siloxanes in the form of biogas from simulated municipal-solid-waste landfill and the corresponding driving mechanism.

Simulated landfill bioreactors were established and operated for 635 days to investigate the dynamic release of seven siloxanes in landfill biogas (denoted by octamethyltrisiloxane (L3), decamethyltetrasiloxane (L4), dodecamethylpentasiloxane (L5), hexamethylcyclotrisiloxane (D3), octamethylcyclotetrasiloxane (D4) and decamethylcyclopentasiloxane (D5) and dodecamethylcyclohexasiloxane (D6)). In total, 259.45, 252.73, 233.30, 80.40, 4.35, 1.67 and 1.10 mg of D5, D3, D4, D6, L4, L5 and L3 were discharged from 57 kg of municipal solid waste (MSW). More than 70 % of the siloxanes were released before day 119, indicating that the peak period of siloxane discharge occurred during the hydrolysis and acid production stage. The cyclosiloxanes (D3, D4, D5 and D6) were the dominant siloxane species in the biogas. The mass load of discharged cyclosiloxanes was more than 98 % of that of the total siloxanes. In addition to the variation in the concentration distribution profiles of the different siloxane species in the MSW, transformations among species may have an important effect on the release of siloxanes. The main transformation products were D3 and D4 with high release rates (>20 %) and high measured contents of trimethylsilanol (TMSOH) and functional microorganisms (Pseudomonas) were observed during landfilling. These results suggested that MSW degradation and transformation of siloxanes both drive the dynamic release of siloxanes during long-term landfilling.

Potentially toxic elements (PTEs) and ecological risk at waste disposal sites: An analysis of sanitary landfills.

This study presents an analysis of soil contamination caused by Ni, Zn, Cd, Cu, and Pb at municipal solid waste (MSW) landfills, with a focus on ecological risk assessment. The approach aims to assess how different landfill practices and environmental conditions affect soil contamination with potentially toxic elements (PTEs) and associated environmental risks. Soil samples were collected from MSW landfills in Poland and the Czech Republic. The research included a comprehensive assessment of PTEs in soils in the context of global environmental regulations. The degree of soil contamination by PTEs was assessed using indices: Geoaccumulation Index (Igeo), Single Pollution Index (Pi), Nemerow Pollution Index (PN), and Load Capacity of a Pollutant (PLI). The ecological risk was determined using the Risk of PTEs (ERi) and Sum of Individual Potential Risk Factors (ERI). The maximum values of the indicators observed for the Radiowo landfill were as follows: Igeo = 4.04 for Cd, Pi = 24.80 for Cd, PN = 18.22 for Cd, PLI = 2.66, ERi = 744 for Cd, ERI = 771.80. The maximum values of the indicators observed for the Zdounky landfill were as follows: Igeo = 1.04 for Cu, Pi = 3.10 for Cu, PN = 2.52 for Cu, PLI = 0.27, ERi = 25 for Cd, ERI = 41.86. The soils of the tested landfills were considered to be non-saline, with electrical conductivity (EC) values less than 2,000 µS/cm. Varying levels of PTEs were observed, and geostatistical analysis highlighted hotspots indicating pollution sources. Elevated concentrations of Cd in the soil indicated potential ecological risks. Concentrations of Cu and lead Pb were well below the thresholds set by the environmental legislation in several countries. In addition, Ni concentrations in the soils of both landfills indicated that the average levels were within acceptable limits. Principal Component Analysis (PCA) revealed common sources of PTEs. The identification of specific risk points at the Radiowo and Zdounky sites contributes to a better understanding of potential hazards in landfill environments. By establishing buffer zones and implementing regular maintenance programs, emerging environmental problems can be addressed in a timely manner.

Plastic waste gasification using oxygen-enriched air and steam: Experimental and model results from a large pilot-scale reactor.

Advanced thermochemical technologies for plastic waste valorization represent an interesting alternative to waste-to-energy options. They are particularly appealing for waste-to-hydrogen and waste-to-chemicals applications, with autothermal steam-oxygen gasification in fluidized bed reactors showing the greatest market potential. The study describes a series of experimental tests carried out on a large pilot-scale fluidized bed gasifier, using steam and O2-enriched air, with increasing fractions of oxygen. Different values of the main operating parameters are varied: equivalence ratio (0.22-0.25), steam-to-carbon ratio (0.7-1.13), and steam-to-oxygen ratio (up to 3.2). The fuel consists of real mixed plastic waste coming from separate collection of municipal solid wastes. The data obtained are used to investigate in depth the role of the main operating parameters and to improve and validate a recently developed one-dimensional kinetic model for waste gasification. The validation shows a good agreement between experimental data and model results, suggesting the reliability of the model to predict the reactor behavior under conditions of pure steam-oxygen gasification, relevant to many industrial applications. It has been found that the equivalence ratio is the parameter that most affects the syngas composition. At a constant equivalent ratio, the molar fraction of oxygen in the enriched air shows a limited influence on syngas composition while the steam is crucial in controlling the temperature along the reactor. Provided that the steam-to-carbon molar ratio is larger than 1.5, steam affects mainly the reactor temperature rather than the syngas composition, qualifying the steam-to-oxygen molar ratio as an instrumental parameter for smooth plant operation.

Life cycle assessment and cost analysis of an innovative automatic system for sorting municipal solid waste: A case study at Milan Malpensa airport.

With the recent advancement in artificial intelligence, there are new opportunities to adopt smart technologies for the sorting of materials at the beginning of the recycling value chain. An automatic bin capable of sorting the waste among paper, plastic, glass & aluminium, and residual waste was installed in public areas of Milan Malpensa airport, a context where the separate collection is challenging. First, the airport waste composition was assessed, together with the efficiency of the manual sorting performed by passengers among the conventional bins: paper, plastic, glass & aluminium, and residual waste. Then, the environmental (via the life cycle assessment - LCA) and the economic performances of the current system were compared to those of a system in which the sorting is performed by the automatic bin. Three scenarios were evaluated: i) all waste from public areas, despite being separately collected, is sent to incineration with energy recovery, due to the inadequate separation quality (S0); ii) recyclable fractions are sent to recycling according to the actual level of impurities in the bags (S0R); iii) fractions are sorted by the automatic bin and sent to recycling (S1). According to the results, the current separate collection shows a 62 % classification accuracy. Focusing on LCA, S0 causes an additional burden of 12.4 mPt (milli points) per tonne of waste. By contrast, S0R shows a benefit (-26.4 mPt/t) and S1 allows for a further 33 % increase of benefits. Moreover, the cost analysis indicates potential savings of 24.3 €/t in S1, when compared to S0.