Glass ionomer cement particles pre-reacted with chlorhexidine: Physical/chemical properties and antimicrobial activity.

OBJECTIVE: Analyze the effects of the functionalization of pre-functionalized GIC particles with chlorhexidine on the physicochemical properties and antimicrobial activity. MATERIALS AND METHODS: Four groups were prepared: (1) GIC (Bioglass R - Biodinamica) - control group; (2) GIC-CHX 1%: Group containing 1% pre-reacted CHX particles; (3) GIC-CHX 2.5%: Group containing 2.5% pre-reacted CHX particles; (4) GIC-CHX 5%: Group containing 5% pre-reacted CHX particles. Hourglass-shaped specimens (10 mm × 2 mm x 1 mm) were fabricated for mechanical tests including cohesive strength (n = 12), modulus of elasticity (n = 12) and microhardness (n = 10). Discs (10 mm × 2 mm) were prepared for the analysis of Ca+2, PO4- and F- ions release (n = 3), and roughness (n = 12). To evaluate the setting time, a Gilmore needle was used according to ISO 9917-1:2016. Disk-shaped specimens (5 × 1mm) were manufactured and subjected to bacterial activity (n = 9) (Streptococcus mutans ATCC 159). RESULTS: Modulus, roughness, setting time and ions release (Ca+2, PO4-, and F-) there were no statistically significant differences among the groups (p > 0.05). The setting time did not change with the incorporation of CHX. The GIC-CHX 2.5% and GIC-CHX 5% groups exhibited superior antibacterial activity compared to the control group and GIC-CHX 1% (p < 0.001). The GIC-CHX 5% group showed the highest microhardness values (p < 0.041), cohesive strength (p < 0.009) when compared to the control group. CONCLUSION: The pre-reacted CHX in GICs was able to confer antimicrobial activity, improve cohesive strength, microhardness, and did not impair ion release, setting time, and roughness.

Anti-Acanthamoeba metallopharmaceuticals: Amoebicidal activity and synergistic effect of copper(II) coordination compound.

Acanthamoeba spp. emerged as a clinically important pathogen related to amoebic keratitis. It is among the main causes of corneal transplantation and vision loss in ophthalmology. The treatment protocols have a low cure rate, high toxicity, and need for drug combination. Transition metal compounds have shown promising antiprotozoal effects. This study evaluates the amoebicidal activity of copper(II) coordination compounds in combination with chlorhexidine and the cytotoxicity to topical ocular application. These copper(II) coordination compounds were screened against Acanthamoeba castellanii trophozoites (ATCC 50492). The cytotoxicity on rabbit corneal cell line (ATCC-CCL 60) was performed. The compounds showed high amoebicidal potential, with inhibition of trophozoite viability above 80%. The Cp12 and Cp13 compounds showed Minimal Inhibitory Amoebicidal Concentration (MIAC) at 200 µM and mean inhibitory concentration (IC50) values lower than 10 µM. Against the cysts, Cp12 showed a reduction in viability (48%) in the longest incubation period. A synergistic effect for Cp12 with chlorhexidine was observed. The compounds have a dose-dependent effect against rabbit corneal cells. Compound Cp12 has potential for future application in developing ophthalmic formulations against Acanthamoeba keratitis and its use in multipurpose solutions is highlighted.

Adhesion and sealing of different universal adhesive systems associated with bulk-fill resins after using endodontic irrigation solutions: An in vitro study.

This study aimed to evaluate the interface of universal adhesive (UA) with bulk-fill resin (BF) and dentin, after endodontic irrigation. The pulp chamber of 96 molars was irrigated with chlorhexidine 2% (CHX) or sodium hypochlorite 5.25% (NaOCl) and restored according to three restorative protocols. Microtensile bond strength (µTBS) and nanoleakage tests were performed after 24 h of thermocycling. Kruskal Wallis, Mann-Whitney and Wilcoxon were performed (p < 0.05). Comparing restorative systems, a difference was found only when irrigated with CHX after 24 h. CHX provided higher µTBS than NaOCl after 24 h for two restorative protocols; after thermocycling, NaOCl provided the greatest µTBS than CHX for one group. Decreased µTBS was observed for all restorative systems when CHX was used after thermocycling. NaOCl demonstrated the highest nanoleakage. The composition of UA influenced the immediate adhesion and sealing to BF when CHX was used; ageing has a deteriorating effect on adhesion and sealing for all restorative systems.

Synthesis and Characterization of Cassava Gum Hydrogel Associated with Chlorhexidine and Evaluation of Release and Antimicrobial Activity.

Hydrogels from natural sources are attracting increasing interest due to their ability to protect biologically active molecules. Starch extracted from cassava tubers is a promising material for synthesizing these hydrogels. Copolymerization of cassava gum and incorporation of chlorhexidine digluconate (CLX) into the hydrogels is confirmed by changes in the crystallographic profile, as observed through X-ray diffraction, and a shift in the 1000 cm-1 band in the Fourier-transform infrared spectroscopy spectrum. The differential scanning calorimetry reveals changes in the decomposition temperature of the synthesized hydrogels related to CLX volatility. Micrographs illustrate the material's porosity. Release tests indicate a constant linear release over 72 h, while antimicrobial activity against Staphylococcus aureus, Escherichia coli, and Candida albicans is satisfactory, with 100% effectiveness from 0.5% CLX and the formation of inhibition halos. Toxicity and biocompatibility studies show no cytotoxicity. The continuous release of chlorhexidine is promising for components of biomedical implants and applications as it can ensure antimicrobial action according to specific therapeutic needs.

Did in-between rinsing and agitating with distilled water prevents precipitate formation by the interaction between sodium hypochlorite and chlorhexidine canal irrigants?

The interaction of sodium hypochlorite (NaOCl) and chlorhexidine gluconate (CHX) produces an orange-brown precipitate. The present study evaluated the influence of distilled water (H2 O) in different irrigation protocols designed to prevent the formation of precipitate with NaOCl and CHX. Fifty canine teeth were instrumented and split longitudinally. The canal was examined with a stereomicroscope and photographed by canal-thirds. The tooth halves were repositioned and distributed randomly into five groups, according to the final irrigation protocol (n = 10): G1 (control)-Ethylenediaminetetraacetic acid (EDTA) + NaOCl + CHX, conventional irrigation (CI); G2-EDTA + NaOCl + CHX, activated with passive ultrasonic irrigation (PUI); G3-EDTA (PUI) + NaOCl (PUI) + H2 O (CI) + CHX (PUI); G4-EDTA + NaOCl + H2 O + CHX (PUI); G5-EDTA (PUI) + NaOCl (PUI) + H2 O (continuous ultrasonic irrigation [CUI]) + CHX (PUI). The specimens were evaluated with a stereomicroscope and scanning electron microscope (SEM). Energy dispersive x-ray spectroscopy analysis was performed to identify the elemental profile of the irrigated canal walls. The images were scored according to the extensiveness of precipitate. Data were analyzed (Kruskal-Wallis test, α = 5%). Under the stereomicroscope, G1 had significantly higher scores than all the other groups in all canal-thirds (p < .05). All four experimental groups showed similar scores (p > .05). There were no significant differences in precipitate formation among root-thirds in intragroup analysis (p > .05). Upon SEM examination, overall, only G5 had lower scores than G1 (p < .05). Analysis by canal-thirds showed no significant difference among groups and among canal-thirds in the intragroup analysis (p > .05). G1 showed high Cl peaks. In-between irrigation with H2 O activated by CUI is effective in preventing precipitate formation during canal debridement with NaOCl and CHX. RESEARCH HIGHLIGHTS: Continuous ultrasonic irrigation with distilled water was capable to prevent the precipitate formation. The precipitate can be classified as a chemical smear layer.

Microbiological, physicomechanical, and surface evaluation of an experimental self-curing acrylic resin containing halloysite nanotubes doped with chlorhexidine.

OBJECTIVE: The objective was to synthesize halloysite nanotubes loaded with chlorhexidine (HNT/CHX) and evaluate the antimicrobial activity, microhardness, color change, and surface characteristics of an experimental self-curing acrylic resin containing varying concentrations of the synthesized nanomaterial. METHODS: The characterization of HNT/CHX was carried out by calculating incorporation efficiency, morphological and compositional, chemical and thermal evaluations. SAR disks were made containing 0 %, 3 %, 5 %, and 10 % of HNT/CHX. Specimens (n = 3) were immersed in distilled water and spectral measurements were carried out using UV/Vis spectroscopy to evaluate the release of CHX for up to 50 days. The antimicrobial activity of the composite against Candida albicans and Streptococcus mutans was evaluated by disk-diffusion test. Microhardness, color analyses (ΔE), and surface roughness (Ra) (n = 9) were performed before and after 30 days of immersion. Data were analyzed using ANOVA/Bonferroni. {Results.} The incorporation efficiency of CHX into HNT was of 8.15 %. All test groups showed controlled and cumulative CHX release up to 30 or 50 days. Significant antimicrobial activity was verified against both microorganisms (p < 0.001). After the 30-day immersion period, the 10 % HNT/CHX group showed a significant increase in hardness (p < 0.05) and a progressive color change (p < 0.001). At T0, the 5 % and 10 % groups exhibited Ra values similar to the control group (p > 0.05), while at T30, all groups showed similar roughness values (p > 0.05). {Significance.} The modification of a SAR with HNT/CHX provides antimicrobial effect and controlled release of CHX, however, the immediate surface roughness in the 3 % group was compromised when compared to the control group.

Dual nanocarrier of chlorhexidine and fluconazole: Physicochemical characterization and effects on microcosm biofilms and oral keratinocytes.

OBJECTIVES: This study assembled and characterized a dual nanocarrier of chlorhexidine (CHX) and fluconazole (FLZ), and evaluated its antibiofilm and cytotoxic effects. METHODS: CHX and FLZ were added to iron oxide nanoparticles (IONPs) previously coated by chitosan (CS) and characterized by physical-chemical analyses. Biofilms from human saliva supplemented with Candida species were grown (72 h) on glass discs and treated (24 h) with IONPs-CS carrying CHX (at 39, 78, or 156 µg/mL) and FLZ (at 156, 312, or 624 µg/mL) in three growing associations. IONPs and CS alone, and 156 µg/mL CHX + 624 µg/mL FLZ (CHX156-FLZ624) were tested as controls. Next, microbiological analyses were performed. The viability of human oral keratinocytes (NOKsi lineage) was also determined (MTT reduction assay). Data were submitted to ANOVA or Kruskal-Wallis, followed by Fisher's LSD or Tukey's tests (α=0.05). RESULTS: Nanocarriers with spherical-like shape and diameter around 6 nm were assembled, without compromising the crystalline property and stability of IONPs. Nanocarrier at the highest concentrations was the most effective in reducing colony-forming units of Streptococcus mutans, Lactobacillus spp., Candida albicans, and Candida glabrata. The other carriers and CHX156-FLZ624 showed similar antibiofilm effects, and significantly reduced lactic acid production (p<0.001). Also, a dose-dependent cytotoxic effect against oral keratinocytes was observed for the dual nanocarrier. IONPs-CS-CHX-FLZ and CHX-FLZ significantly reduced keratinocyte viability at CHX and FLZ concentrations ≥7.8 and 31.25 µg/mL, respectively (p<0.05). CONCLUSION: The nanotherapy developed outperformed the effect of the combination CHX-FLZ on microcosm biofilms, without increasing the cytotoxic effect of the antimicrobials administered. CLINICAL SIGNIFICANCE: The dual nanocarrier is a promising topically-applied therapy for the management of oral candidiasis considering that its higher antibiofilm effects allow the use of lower concentrations of antimicrobials than those found in commercial products.

Interactions Between Calcium Hypochlorite and Irrigants Commonly Used in Endodontic Practice: A Chemical Analysis.

INTRODUCTION: This study aimed to identify possible products resulting from chemical interactions between calcium hypochlorite (Ca[OCl]2) and other irrigants for endodontic use using electrospray ionization quadrupole time-of-flight mass spectrometry. METHODS: The 5.25% Ca(OCl)2 was associated with either 70% ethanol solution, distilled water, saline solution (0.9% sodium chloride), 5% sodium thiosulfate, 10% citric acid, 17% ethylenediaminetetraacetic acid (EDTA), or 2% chlorhexidine (CHX). The reaction ratio was 1:1 and the products obtained were analyzed by electrospray ionization quadrupole time-of-flight mass spectrometry. RESULTS: The interactions between Ca(OCl)2 and CHX generated an orange-brown precipitate, without identification of para-chloroaniline and between Ca(OCl)2 and sodium thiosulfate, a milky-white precipitate. Furthermore, when the oxidizing agent was associated with EDTA and citric acid, chlorine gas was released. As for the other associations, 70% ethanol, distilled water, and saline solution, no precipitation or gas release occurred. CONCLUSIONS: The orange-brown precipitate occurs due to the chlorination of guanidine nitrogens, and the milky-white precipitate is due to the partial neutralization of the oxidizing agent. The release of chlorine gas occurs due to the low pH of the mixture, which results in the rapid formation and decomposition of chlorine. In this context, an intermediate rinsed with distilled water, saline solution, and ethanol between Ca(OCl)2 and CHX, citric acid, and EDTA seems to be appropriate to prevent the formation of by-products when these irrigants need to be used in the canal. Furthermore, if it is necessary to use sodium thiosulfate, a larger volume of the solution must be used compared to that used for the oxidizing solution.

Films composed of white angico gum and chitosan containing chlorhexidine as an antimicrobial agent.

Anadenanthera colubrina, popularly known as white angico, is a species extensively cultivated in Brazil, mainly in the cerrado region, including the state of Piauí. This study examines the development of films composed of white angico gum (WAG) and chitosan (CHI) and containing chlorhexidine (CHX), an antimicrobial agent. The solvent casting method was used to prepare films. Different combinations and concentrations of WAG and CHI were used to obtain films with good physicochemical characteristics. Properties such as the in vitro swelling ratio, the disintegration time, folding endurance, and the drug content were determined. The selected formulations were characterised by scanning electron microscopy, Fourier-transform infrared spectroscopy, differential scanning calorimetry, thermogravimetric analysis, and X-ray diffraction, and the CHX release time and antimicrobial activity were evaluated. CHX showed a homogenous distribution in all CHI/WAG film formulations. The optimised films showed good physicochemical properties with 80% CHX release over 26 h, which is considered promising for local treatment of severe lesions in the mouth. Cytotoxicity tests of the films did not show toxicity. The antimicrobial and antifungal effects were very effective against the tested microorganisms.

Development, characterization and antimicrobial activity of multilayer silica nanoparticles with chlorhexidine incorporated into dental composites.

OBJECTIVE: In this study a dentistry nanocomposite with prolonged antibacterial activity using silica nanoparticles (SNPs) loaded with chlorhexidine (CHX) was developed. METHODS: SNPs were coated with the Layer-by-Layer technique. Dental composites were prepared with organic matrix of BisGMA/TEGDMA and SNPs with or without CHX (0, 10, 20 or 30% w/w). The physicochemical properties of the developed material were evaluated and agar diffusion method was used to test the antibacterial. In addition, the biofilm inhibitory activity of the composites was evaluated against S. mutans. RESULTS: SNPs were rounded with diameters about 50 nm, the organic load increased with increasing deposited layers. Material samples with SNPs loaded with CHX (CHX-SNPs) showed the highest values of post-gel volumetric shrinkage, that ranged from 0.3% to 0.81%. Samples containing CHX-SNPs 30% w/w showed the highest values of flexural strength and modulus of elasticity. Only samples containing SNPs-CHX showed growth inhibition against S. mutans, S. mitis and S. gordonii in a concentration-dependent manner. The composites with CHX-SNPs reduced the biofilm formation of S. mutans biofilm at 24 h and 72 h. SIGNIFICANCE: The nanoparticle studied acted as fillers and did not interfere with the evaluated physicochemical properties while providing antimicrobial activity against streptococci. Therefore, this initial study is a step forward to the synthesis of experimental composites with improved performance using CHX-SNPs.

Twenty-month Performance of a Universal Bonding System on Simulated-challenged Dentin Substrates Pretreated with Chlorhexidine.

OBJECTIVES: Since the use of dentin antiproteolytic agents with universal adhesives (UAs) can potentially degrade the bonding interface, this study evaluated bond strengths with and without chlorhexidine (CHX) on variously altered dentin surfaces for up to 20 months. METHODS: Human molar specimens (n=20) were categorized by substrates as S=sound, E=eroded, and C=carious, and by pretreatment as W=water or CHX. These specimens were subjected to micro-tensile bond strength (µTBS) testing at 24 hours, 6 months, and 20 months, after 30 seconds of pretreatment with CHX or W, followed by self-etching and bonding (Adper Single Bond Universal, 3M ESPE). Modes of failure were assessed using optical microscopy (40×) and scanning electron microscopy (SEM), and the results were analyzed by 3-way ANOVA and Tukey's statistical tests (α=0.05). RESULTS: Substrate (p<0.001), pre-treatment (p=0.0413), and time (p<0.0001) were statistically significant. The sound-dentin group in initial time (W=39.27/CHX=40.55) yielded the higher µTBS values (MPa) in comparison with altered substrates pre-treated with CHX (E-CHX=19.84; C-CHX=18.24) after 20 months, which showed the lowest values. Under SEM analysis, heterogeneous patterns appeared in the hybrid layer of the CHX-treated group, particularly in the altered substrates. CONCLUSIONS: Bond strength to dentin decreased over a period of 20 months using UA with 10-methacryloyloxydecyl-dihydrogen phosphate (MDP) in self-etching mode. Substrates altered by erosion or caries have impaired adhesion and associated clinical use of UA with MDP and CHX should be avoided.

Influence of chlorhexidine, propolis, pulpal pressure simulation, and aging on dentin bond strength.

The present study evaluated the bond strength (µTBS) of dentin treated with chlorhexidine and propolis subjected to simulated pulpal pressure (SPP) and thermocycle aging. One hundred and twenty healthy human molars were sectioned to obtain 2 mm of dentin thickness and were divided into two groups (n = 60): SPP (15 cm H2 O) and no SPP (Control group). Dentin surfaces were conditioned with 37% phosphoric acid for 15 s and were divided according to the dentin treatment (n = 20): Control; Chlorhexidine gluconate (0.2% for 30 s) and Propolis (aqueous propolis extract for 30 s). Half of the specimens were submitted to 15,000 thermocycle aging (5 ± 2°C and 55 ± 2°C). The samples were sectioned into beams and submitted to µTBS. Data were analyzed by three-way ANOVA (SPP × Dentin treatment × Thermocycle aging) and the Tukey's tests (p < .001). With regard to the SPP, ANOVA revealed that the Control group (32.98 MPa) had significantly higher values of µTBS when compared to the SPP (29.19 MPa). With regard to Thermocycle aging, no aging (34.05 MPa) had significantly higher values of µTBS when compared to the aging (28.12 MPa). With regard to the dentin treatment, Propolis and Chlorhexidine did not statistically influence the results (p > .05). The SPP and thermocycle aging negatively influenced the bond strength between the dentin and resin; the 0.2% chlorhexidine digluconate and aqueous propolis extract solutions did not interfere in the bond strength between the resin and dentin. The use of chlorhexidine and propolis as a dental treatment may not influence the dentin bond strength, but SPP and thermocycle aging may damage the longitudinal dentin bond strength. RESEARCH HIGHLIGHTS: Chlorhexidine and propolis as a dental treatment may not influence the dentin bond strength. Simulated pulpal pressure and thermocycle aging may damage the longitudinal dentin bond strength.

Melaleuca alternifolia essential oil soap: a potential alternative for hand hygiene.

This study aimed to compare the antimicrobial action of three soaps for hand hygiene (HH): 2.0% Tea Tree Oil (TTO); 0.5% triclosan; 2.0% chlorhexidine, and to explore the perception of healthcare professionals about TTO. Two-step study: a quantitative, to determine the logarithmic reduction of Escherichia coli K12 colony-forming units before and after HH of 15 volunteers and quali-quantitative, through interviews with 23 health professionals. All the three products demonstrated antimicrobial action (a log10 reduction factor of 4.18 for TTO, 4.31 for triclosan, 3.89 for chlorhexidine, and 3.17 for reference soap). Professionals remarked the pleasant aroma and non-dryness of skin when using soap containing TTO.

Chlorhexidine Nanoemulsion: A New Antiseptic Formulation.

INTRODUCTION: Nanoparticle solutions have been studied to improve antimicrobial effect. The aim of this study was to develop, characterize, and evaluate the in vitro and in vivo antiseptic efficacy of 0.25% aqueous-based chlorhexidine nanoemulsion (NM-Cl 0.25% w/v). METHODS: The NM-Cl 0.25% w/v (2.5mg/mL) and free chlorhexidine nanoemulsion (FCN; same composition of NM-Cl without the molecule of chlorhexidine) were synthetized by the spontaneous emulsification method. Characterization analyses of physical and chemical properties were performed. The NM-Cl 0.25% w/v was compared with chlorhexidine 0.5% alcohol base (CS-Cl 0.5%) in vitro studies (microdilution study and kill curve study), and in vivo study (antisepsis of rats dorsum). Kruskal-Wallis test was used between groups and inside the same group, at different sample times and the Mann-Whitney test was performed when difference was detected. RESULTS: The NM-Cl 0.25% w/v presented adequate physicochemical characteristics for a nanoemulsion, revealing a more basic pH than FCN and difference between zeta potential of NM-Cl 0.25% w/v and FCN. The NM-Cl 0.25% w/v and CS-Cl 0.5% solutions were more effective on Gram-positive than on Gram-negative bacteria (p≤0.05). NM-Cl 0.25% w/v presented upper antiseptic effect in the microdilution study and residual antiseptic effect was maintained for a longer time when compared to CS-Cl 0.5% (kill curve study). The four-fold (minimal inhibitory concentration) of NM-Cl 0.25% were the formulations with most durable effect within those tested, presenting residual effect until T6 for both bacteria. In the in vivo study, both formulations (NM-Cl 0.25% w/v and CS-Cl 0.5%) had a reduction of the microorganisms in the skin of the rats (p<0.0001) not revealing any difference between the formulations at different times, showing the antiseptic effect of NM-Cl (p≤0.05). CONCLUSION: Both in vitro and in vivo experiments demonstrated that NM-Cl showed promising future as an antiseptic for cutaneous microbiota.

Corn starch films as a long-term drug delivery system for chlorhexidine gluconate.

The present study describes the development of a chlorhexidine long-term drug delivery system using starch as a biodegradable polymer base. Three batches of thermoplastic starch films, containing starch particles/nanoparticles and chlorhexidine (CHX), were manufactured by casting. Morphological characterization showed an irregular surface with particles incorporated with chlorhexidine agglomerated in a starch matrix. Nanoindentation showed that the control film (without chlorhexidine) presented a more plastic and rigid behavior in relation to the films containing CHX. CHX was partially bounded to starch and prevented starch crystallization. Starch nanoparticles formed by precipitation were observed through transmission electron microscopy. By incorporating CHX into the solution, the nanoparticles presented different morphology, suggesting absorption of the drug. In vitro drug release was observed for 21 days by UV-vis spectrophotometry and released CHX amounted up to 19 mg/100 ml. Films presented microbiological potential for inhibiting Staphylococcus aureus growth as evaluated by the disk diffusion test in agar. It has been concluded that the developed film met the main requirements for a drug delivery system and that it is possible to be produced from a simple, cheap and reproduceable process.

Antimicrobial activity of intracanal dressings composed by natural products associated to chlorhexidine and its influence on dentinal colour change / Avaliação da ação antimicrobiana de medicações intracanais à base de produtos fitoterápicos associados à clorexidina e sua influência na alteração de cor da estrutura dentinária

Purpose: evaluate the antimicrobial activity of intracanal dressings and their influence on dentinal colour changes. Material and methods: eighty single-rooted human extracted teeth were decoronated and divided into eight groups (n=10) according to intracanal dressing protocols inserted into the root canals: G1­distilled water (DW); G2­2% chlorhexidine gel (CHX); G3­calcium hydroxide (Ca[OH]2)+DW; G4­grape seed extract (GSE)+DW; G5­ginger extract (GE)+DW; G6­Ca(OH)2+CHX; G7­GSE+CHX; and G8­GE+CHX. The antimicrobial activity was evaluated by colony-forming units (CFUs) counting and dentinal colour changes was evaluated by digital spectrophotometry. Data were statistically analysed by One-way ANOVA followed by Tukey´s post hoc test (antimicrobial evaluation) and non-parametric Wilcoxon followed by the Mann- Whitney-U test (colour change evaluation) (α=0.05). Results: the highest bacterial reduction was observed in groups 4, 6, 7 and 8, with no significant difference between them (p<0.05). Groups 4 and 7 showed the highest medians of dentinal colour change (p<0.05). Conclusion: the addition of CHX improved the antimicrobial activity of GE-based intracanal dressing, with no effect in GSE-based intracanal dressing; moreover, these protocols induced significant dentinal colour changes. (AU)

Objetivo: avaliar a atividade antimicrobiana de medicações intracanais e sua influência na alteração da cor dentinária. Materiais e métodos: oitenta dentes humanos extraídos unirradiculares foram seccionados e divididos em oito grupos (n = 10), de acordo com os protocolos de medicação intracanal inseridos nos canais radiculares: água destilada G1 (DW); G2-2% de gel de clorexidina (CHX); hidróxido de cálcio G3 ­ (Ca [OH] 2) + DW; extrato de semente de uva G4 (GSE) + DW; extrato de gengibre G5 (GE) + DW; G6- Ca (OH) 2 + CHX; G7 ­ GSE + CHX; e G8-GE + CHX. A atividade antimicrobiana foi avaliada por contagem de unidades formadoras de colônias (UFCs) e as alterações de cor dentinária foram avaliadas por espectrofotometria digital. Os dados foram analisados estatisticamente por ANOVA one-way, seguida pelo teste post hoc de Tukey (avaliação antimicrobiana) e Wilcoxon não paramétrico, seguido pelo teste de Mann- Whitney-U (avaliação da mudança de cor) (α = 0,05). Resultados: a maior redução bacteriana foi observada nos grupos 4, 6, 7 e 8, sem diferença significativa entre eles (p < 0,05). Os grupos 4 e 7 apresentaram as maiores medianas da alteração da cor dentinária (p < 0,05). Conclusão: a adição de CHX melhorou a atividade antimicrobiana da medicação intracanal baseado em GE, sem efeito na medicação intracanal baseado em GSE; além disso, esses protocolos induziram alterações significativas na cor dentinária.(AU)

Adhesive resistance of a copaiba oil-based dentin biomodifier.

This study analyzed the effect of prior application of copaiba oil (CO) emulsions as a dentin cleaning substance on microleakage and microtensile adhesive strength. Twenty-five premolars and sixty-four molars were used for microleakage and microtensile assays. For the microleakage assays, specimens with standard class V cavities were divided (n = 5), according to the tested CO emulsions: CO10%X, CO10%Y, and CO10%Z, as well as chlorhexidine 2% (CHX) and distilled water (DW), as positive and negative controls, respectively. Restorations were performed using the Adper Single Bond® and/or Clearfil SE Bond® systems. Cervical, occlusal, distal and mesial sections were assessed for tracer penetration degree at the composite/tooth interface. For the microtensile assay, healthy molars were divided into sixteen groups, in which artificial caries were induced in half of the groups. Dentin surfaces were treated with CO10%X and CO10%Y, CHX and DW. Microtensile bond strength was measured by fixing each sample to the plate of a universal testing machine operated at a speed of 0.5 mm/minute until failure. Dentin treated with CO10%X showed a lower infiltration rate than dentin treated with the other CO emulsions, CHX2% and DW. According to the microtensile assay, both healthy and affected dentin treated with CO10%X and Adper Single Bond® adhesive system presented higher adhesive strength. CO emulsion, used as a dentin biomodifier, interfered positively in microleakage and improved adhesive strength after acid etching in the Adper Single Bond® adhesive system, or before applying the Clearfil SE Bond® self-etching system.

Evaluation of the physical and antifungal effects of chlorhexidine diacetate incorporated into polymethyl methacrylate.

OBJECTIVE: This study aimed to evaluate the physical properties and antifungal activities of polymethyl methacrylate (PMMA) acrylic resins after the incorporation of chlorhexidine diacetate salt (CDA). METHODOLOGY: First, acrylic resin specimens were fabricated with Vipi Cor® and DuraLay® resins with and without the incorporation of 0.5%, 1.0% or 2.0% CDA. The residual monomer and CDA release were measured at intervals ranging from 2 hours to 28 days using ultraviolet spectrometry combined with high-performance liquid chromatography. The antifungal activity against C. albicans was evaluated with the agar diffusion method. Fourier transform infrared spectroscopy was used to analyze the degree of resin conversion. Finally, the water sorption values of the resins were also measured. RESULTS: The incorporated CDA concentration significantly changed the rate of CDA release (p<0.0001); however, the brand of the material appeared to have no significant influence on drug release. Subsequently, the inhibition zones were compared between the tested groups and within the same brand, and only the comparisons between the CDA 2% and CDA 1% groups and between the CDA 1% and CDA 0.5% groups failed to yield significant differences. Regarding the degrees of conversion, the differences were not significant and were lower only in the CDA 2% groups. Water sorption was significantly increased at the 1.0% and 2.0% concentrations. CONCLUSIONS: We concluded that the incorporation of CDA into PMMA-based resins enabled the inhibition of C. albicans growth rate, did not alter the degrees of conversion of the tested resins and did not change the release of residual monomers.

Adhesive resistance of a copaiba oil-based dentin biomodifier

Abstract This study analyzed the effect of prior application of copaiba oil (CO) emulsions as a dentin cleaning substance on microleakage and microtensile adhesive strength. Twenty-five premolars and sixty-four molars were used for microleakage and microtensile assays. For the microleakage assays, specimens with standard class V cavities were divided (n = 5), according to the tested CO emulsions: CO10%X, CO10%Y, and CO10%Z, as well as chlorhexidine 2% (CHX) and distilled water (DW), as positive and negative controls, respectively. Restorations were performed using the Adper Single Bond® and/or Clearfil SE Bond® systems. Cervical, occlusal, distal and mesial sections were assessed for tracer penetration degree at the composite/tooth interface. For the microtensile assay, healthy molars were divided into sixteen groups, in which artificial caries were induced in half of the groups. Dentin surfaces were treated with CO10%X and CO10%Y, CHX and DW. Microtensile bond strength was measured by fixing each sample to the plate of a universal testing machine operated at a speed of 0.5 mm/minute until failure. Dentin treated with CO10%X showed a lower infiltration rate than dentin treated with the other CO emulsions, CHX2% and DW. According to the microtensile assay, both healthy and affected dentin treated with CO10%X and Adper Single Bond® adhesive system presented higher adhesive strength. CO emulsion, used as a dentin biomodifier, interfered positively in microleakage and improved adhesive strength after acid etching in the Adper Single Bond® adhesive system, or before applying the Clearfil SE Bond® self-etching system.