Time resolved Fabry-Perot measurements of cavity temperature in pulsed QCLs.

Temperature rise during operation is a central concern of semiconductor lasers and especially difficult to measure during a pulsed operation. We present a technique for in situ time-resolved temperature measurement of quantum cascade lasers operating in a pulsed mode at ~9.25 µm emission wavelength. Using a step-scan approach with 5 ns resolution, we measure the temporal evolution of the spectral density, observing longitudinal Fabry-Perot modes that correspond to different transverse modes. Considering the multiple thin layers that make up the active layer and the associated Kapitza resistance, thermal properties of QCLs are significantly different than bulk-like laser diodes where this approach was successfully used. Compounded by the lattice expansion and refractive index changes due to time-dependent temperature rise, Fabry-Perot modes were observed and analyzed from the time-resolved emission spectra of quantum cascade lasers to deduce the cavity temperature. Temperature rise of a QCL in a pulsed mode operation between -160 °C to -80 °C was measured as a function of time. Using the temporal temperature variations, a thermal model was constructed that led to the extraction of cavity thermal conductivity in agreement with previous results. Critical in maximizing pulsed output power, the effect of the duty cycle on the evolution of laser heating was studied in situ, leading to a heat map to guide the operation of pulsed lasers.

Stress evolution of Ge nanocrystals in dielectric matrices.

Germanium nanocrystals (Ge NCs) embedded in single and multilayer silicon oxide and silicon nitride matrices have been synthesized using plasma enhanced chemical vapor deposition followed by conventional furnace annealing or rapid thermal processing in N2 ambient. Compositions of the films were determined by Rutherford backscattering spectrometry and x-ray photoelectron spectroscopy. The formation of NCs under suitable process conditions was observed with high resolution transmission electron microscope micrographs and Raman spectroscopy. Stress measurements were done using Raman shifts of the Ge optical phonon line at 300.7 cm-1. The effect of the embedding matrix and annealing methods on Ge NC formation were investigated. In addition to Ge NCs in single layer samples, the stress on Ge NCs in multilayer samples was also analyzed. Multilayers of Ge NCs in a silicon nitride matrix separated by dielectric buffer layers to control the size and density of NCs were fabricated. Multilayers consisted of SiN y :Ge ultrathin films sandwiched between either SiO2 or Si3N4 by the proper choice of buffer material. We demonstrated that it is possible to tune the stress state of Ge NCs from compressive to tensile, a desirable property for optoelectronic applications. We also observed that there is a correlation between the stress and the crystallization threshold in which the compressive stress enhances the crystallization, while the tensile stress suppresses the process.

The role of the interface in germanium quantum dots: when not only size matters for quantum confinement effects.

Quantum confinement (QC) typically assumes a sharp interface between a nanostructure and its environment, leading to an abrupt change in the potential for confined electrons and holes. When the interface is not ideally sharp and clean, significant deviations from the QC rule appear and other parameters beyond the nanostructure size play a considerable role. In this work we elucidate the role of the interface on QC in Ge quantum dots (QDs) synthesized by rf-magnetron sputtering or plasma enhanced chemical vapor deposition (PECVD). Through a detailed electron energy loss spectroscopy (EELS) analysis we investigated the structural and chemical properties of QD interfaces. PECVD QDs exhibit a sharper interface compared to sputter ones, which also evidences a larger contribution of mixed Ge-oxide states. Such a difference strongly modifies the QC strength, as experimentally verified by light absorption spectroscopy. A large size-tuning of the optical bandgap and an increase in the oscillator strength occur when the interface is sharp. A spatially dependent effective mass (SPDEM) model is employed to account for the interface difference between Ge QDs, pointing out a larger reduction in the exciton effective mass in the sharper interface case. These results add new insights into the role of interfaces on confined systems, and open the route for reliable exploitation of QC effects.

Laser induced sponge-like Si in Si-rich oxides for photovoltaics.

We show that a sponge-like structure of interconnected Si nanowires embedded in a dielectric matrix can be obtained by laser annealing of silicon rich oxides (SRO). Due to quantum confinement, the large bandgap displayed by these percolated nanostructures can be utilized as a tandem stage in 3rd generation thin-film solar cells. Well passivated by the SiO2 dielectric matrix, they are expected to overcome the difficulty of carrier separation encountered in the case of isolated crystalline quantum dots. In this study PECVD grown SRO were irradiated by a cw Ar⁺ laser. Raman spectroscopy has been used to assess the crystallinity of the Si nanostructures and thus to optimize the annealing conditions as dwell times and power densities. In addition, Si plasmon imaging in the transmission electron microscope was applied to identify the sponge-like structure of phase-separated silicon.

Chemical and topographical modification of PHBV surface to promote osteoblast alignment and confinement.

Proper cell attachment and distribution, and thus stronger association in vivo between a bone implant and native tissue will improve the success of the implant. In this study, the aim was to achieve promotion of attachment and uniform distribution of rat mesenchymal stem cell-derived osteoblasts by introducing chemical and topographical cues on poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) film surfaces. As the chemical cues, either alkaline phosphatase was covalently immobilized on the film surface to induce deposition of calcium phosphate minerals or fibrinogen was adsorbed to improve cell adhesion. Microgrooves and micropits were introduced on the film surface by negative replication of micropatterned Si wafers. Both chemical cues improved cell attachment and even distribution on the PHBV films, but Fb was more effective especially when combined with the micropatterns. Cell alignment (<10 degrees deviation angle) parallel to chemically modified microgrooves (1, 3, or 8 microm groove width) and on 10 microm-thick Fb lines printed on the unpatterned films was achieved. The cells on unpatterned and 5 microm-deep micropitted films were distributed and oriented randomly. Results of this study proved that microtopographies on PHBV can improve osseointegration when combined with chemical cues, and that microgrooves and cell adhesive protein lines on PHBV can guide selective osteoblast adhesion and alignment.

Contact guidance enhances the quality of a tissue engineered corneal stroma.

Corneal stroma is a very complex structure, composed of 200 lamellae of oriented collagen fibers. This highly complex nature of cornea is known to be important for its transparency and mechanical integrity. Thus, an artificial cornea design has to take into account this complex structure. In this study, behavior of human corneal keratocytes on collagen films patterned with parallel channels was investigated. Keratocytes proliferated well on films and reached confluency after 7 days in the incubation medium. Nearly all of the cells responded to the patterns and were aligned in contrast to the cells on unpatterned surfaces. Collagen type I and keratan sulfate secreted by keratocytes on patterned films appeared to be aligned in the direction of the patterns. The films showed an intermediate degradation over the course of a month. On the whole, transparency of the films increased with degradation and decreased by the presence of the cells. The decrease was, however, low and transparency level was maintained on the patterned films while on the unpatterned films a sharp decrease in transparency was followed by an improvement. This was due to the more organized distribution of cells and the oriented secretion of extracellular matrix molecules on patterned collagen films. Thus, these results suggest that application of contact guidance in cornea tissue engineering may facilitate the remodeling process, hence decrease the rehabilitation period.

Cornea engineering on polyester carriers.

In this study, biodegradable polyester based carriers were designed for tissue engineering of the epithelial and the stromal layers of the cornea, and the final construct was tested in vitro. In the construction of the epithelial layer, micropatterned films were prepared from blends of biodegradable and biocompatible polyesters of natural (PHBV) and synthetic (P(L/DL)LA) origin, and these films were seeded with D407 (retinal pigment epithelial) cells. To improve cell adhesion and growth, the films were coated with fibronectin. To serve as the stromal layer of the cornea, highly porous foams of P(L/DL)LA-PHBV blends were seeded with 3T3 fibroblasts. Cell numbers on the polyester carriers were significantly higher than those on the tissue culture polystyrene control. The cells and the carriers were characterized scanning electron micrographs showed that the foam was highly porous and the pores were interconnected. 3T3 Fibroblasts were distributed quite homogeneously at the seeding site, but probably because of the high thickness of the carrier ( approximately 6 mm); they could not sufficiently populate the core (central parts of the foam) during the test duration. The D407 cells formed multilayers on the micropatterned polyester film. Immunohistochemical studies showed that the cells retained their phenotype during culturing; D407 cells formed tight junctions characteristic of epithelial cells, and 3T3 cells deposited collagen type I into the foams. On the basis of these results, we concluded that the micropatterned films and the foams made of P(L/DL)LA-PHBV blends have a serious potential as tissue engineering carriers for the reconstruction of the epithelial and stromal layers of the cornea.

Mortality rate, length of stay and extra cost of sternal surgical site infections following coronary artery bypass grafting in a private medical centre in Turkey.

Florence Nightingale Hospital is a 300-bed, university-affiliated, private medical centre with a large open heart surgery programme in Istanbul, Turkey. In this study, the mortality rates, lengths of stay (LOS) and extra costs of patients with deep sternal surgical site infections (DSSSIs) and superficial sternal surgical site infections (SSSSIs) following coronary artery bypass grafting (CABG) were determined from January 1999 to December 2002. Group I included 52 patients with DSSSIs, Group II included 36 patients with SSSSIs and Group III included 88 controls. The controls were selected at random from patients operated within the same year, with the same sex and age within five years, but who had not developed infection. Mortality rates in Groups I, II and III were 19.2%, 0% and 4.5%, respectively; the mortality rate in Group I was significantly different from that in Groups II and III (P<0.005). LOS was 47, 33 and 12 days for Groups I, II and III, respectively, and LOS was statistically different for each group (P<0.005). The costs of extra LOS, antibiotics, and radiological, microbiologial and other laboratory examinations for Groups I and II were US$6850.93 and US$3740.58, respectively. Both DSSSI and SSSSI following CABG extended the LOS and increased the cost, and DSSSI was significantly associated with a high mortality rate. These results suggest the need for improved infection control measures to reduce SSSIs following CABG. As an important component of the extra cost is the extra LOS, it is essential to shorten this period. This may be particularly applicable in patients with SSSSIs.

Relationship between dyslipidemia, C-reactive protein and serological evidence of Chlamydia pneumoniae in Turkish patients with coronary artery diseases.

Relationship between dyslipidemia, C-Reactive Protein (CRP) and serological evidence of Chlamydia pneumoniae was investigated in a Turkish population with coronary artery disease. This prospective, randomized, blinded study was carried out in Florence Nightingale Hospital which is affiliated to Kadir Has University, Medical Faculty. Thirty-two patients with acute coronary artery diseases (ACAD), 32 patients with chronic coronary artery diseases (CCAD) and 26 healthy controls (HC) were included in the study. We detected serum concentrations of C. pneumoniae IgG, IgA and IgM by ELISA method. We measured total cholesterol, trigliseride, LDL and HDL- cholesterol levels to determine dyslipidemia which was defined as total cholesterol >200 mg/dL, trigliserid > 150 mg/dL, LDL >130 mg/dL, HDL <45 mg/dL. CRP levels were also measured. Seropositivity to C. pneumoniae IgG was 84.3%, 100% and 65.3%; seropositivity to IgA was 9.3%, 6.2%, and 3.8%; and seropositivity to IgM was 12.5%, 15.3%, and 15.4% in patients with ACAD, CCAD and HC, respectively. Dyslipidemia was found as 93.7%, 78. 1% and 0% of patients with ACAD, CCAD and HC, respectively. CRP level was high in all patients (ACAD, CCAD) but not in healthy controls. As a conclusion, we found a significant association between seropositivity to C. pneumoniae IgG and dyslipidemia and CRP levels in ACAD and CCAD patients (p<0.05). C. pneumoniae IgG antibodies should be evaluated together with serum lipids and CRP levels in patients with ACAD and CCAD in Turkish population. This may help clinicians in treatment of C. pneumoniae infection and decrease the risk of coronary artery diseases.

Characterization of thermally poled germanosilicate thin films.

We report measurements of the nonlinearity profile of thermally poled low-loss germanosilicate films deposited on fused-silica substrates by PECVD, of interest as potential electro-optic devices. The profiles of films grown and poled under various conditions all exhibit a sharp peak ~0.5 microm beneath the anode surface, followed by a weaker pedestal of approximately constant amplitude down to a depth of 13-16 microm, without the sign reversal typical of poled undoped fused silica. These features suggest that during poling, the films significantly slow down the injection of positive ions into the structure. After local optimization, we demonstrate a record peak nonlinear coefficient of ~1.6 pm/V, approximately twice as strong as the highest reliable value reported in thermally poled fused silica glass, a significant improvement that was qualitatively expected from the presence of Ge.

Widespread nocardiosis in two patients with Behçet's disease.

Nocardia spp., a group of gram-positive variably acid-fast aerobic bacteria, are opportunistic pathogens in immunocompromised hosts. We here-within describe 2 cases of widespread nocardiosis in patients with Behcet's disease. In addition to endogen endophthalmitis in case 1, both cases developed lung, brain and skin involvement. Despite brain involvement, the prognosis was good, although vision was completely lost in case 1, which was directly attributable to a delay in both diagnosis and treatment.

Multiple nocardial abscesses of cerebrum, cerebellum and spinal cord, causing quadriplegia.

In this paper we present a case of a diabetic patient with nocardial abscesses of cerebrum, cerebellum and the spinal cord. The present case is the first case in the literature of solitary intramedullary abscess in cervical spinal cord, causing tetraplegia. Nocardia asteroides grew in a culture of the abscess pus. After either surgical excision or drainage of lesions, a triple combination regimen of chemotherapy (amikacin, ceftriaxone and trimethoprim-sulfamethoxazole) was given, but the patient was lost in the postoperative period. This case gives suggestive evidence of an association between cervical spinal cord involvement and poor prognosis in CNS nocardiosis.

Enhancement and inhibition of photolumincescence in hydrogenated amorphous silicon nitride microcavities.

A Fabry-Perot microcavity is used for the enhancement and inhibition of photoluminescence in hydrogenated amorphous silicon nitride. The amplitude of the photoluminescence is enhanced 4 times, while its linewidth is reduced 8 times with respect to the bulk hydrogenated amorphous silicon nitride. The transmittance, reflectance, and absorptance spectra of the microcavity were also measured and calculated. The calculated spectra agree well with the experimental ones.