A Materials Acceleration Platform for Organic Laser Discovery.

Conventional materials discovery is a laborious and time-consuming process that can take decades from initial conception of the material to commercialization. Recent developments in materials acceleration platforms promise to accelerate materials discovery using automation of experiments coupled with machine learning. However, most of the automation efforts in chemistry focus on synthesis and compound identification, with integrated target property characterization receiving less attention. In this work, an automated platform is introduced for the discovery of molecules as gain mediums for organic semiconductor lasers, a problem that has been challenging for conventional approaches. This platform encompasses automated lego-like synthesis, product identification, and optical characterization that can be executed in a fully integrated end-to-end fashion. Using this workflow to screen organic laser candidates, discovered eight potential candidates for organic lasers is discovered. The lasing threshold of four molecules in thin-film devices and find two molecules with state-of-the-art performance is tested. These promising results show the potential of automated synthesis and screening for accelerated materials development.

Probing polaron-induced exciton quenching in TADF based organic light-emitting diodes.

Polaron-induced exciton quenching in thermally activated delayed fluorescence (TADF)-based organic light-emitting diodes (OLEDs) can lead to external quantum efficiency (EQE) roll-off and device degradation. In this study, singlet-polaron annihilation (SPA) and triplet-polaron annihilation (TPA) were investigated under steady-state conditions and their relative contributions to EQE roll-off were quantified, using experimentally obtained parameters. It is observed that both TPA and SPA can lead to efficiency roll-off in 2,4,5,6-tetra(9H-carbazol-9-yl)isophthalonitrile (4CzIPN) doped OLEDs. Charge imbalance and singlet-triplet annihilation (STA) were found to be the main contributing factors, whereas the device degradation process is mainly dominated by TPA. It is also shown that the impact of electric field-induced exciton dissociation is negligible under the DC operation regime (electric field < 0.5 MV cm-1). Through theoretical simulation, it is demonstrated that improvement to the charge recombination rate may reduce the effect of polaron-induced quenching, and thus significantly decrease the EQE roll-off.

Exact Solution of Kinetic Analysis for Thermally Activated Delayed Fluorescence Materials.

The photophysical analysis of thermally activated delayed fluorescence (TADF) materials has become instrumental for providing insights into their stability and performance, which is not only relevant for organic light-emitting diodes but also for other applications such as sensing, imaging, and photocatalysis. Thus, a deeper understanding of the photophysics underpinning the TADF mechanism is required to push materials design further. Previously reported analyses in the literature of the kinetics of the various processes occurring in a TADF material rely on several a priori assumptions to estimate the rate constants for forward and reverse intersystem crossing. In this report, we demonstrate a method to determine these rate constants using a three-state model together with a steady-state approximation and, importantly, no additional assumptions. Further, we derive the exact rate equations, greatly facilitating a comparison of the TADF properties of structurally diverse emitters and providing a comprehensive understanding of the photophysics of these systems.

Molecular Design Based on Donor-Weak Donor Scaffold for Blue Thermally-Activated Delayed Fluorescence Designed by Combinatorial DFT Calculations.

Quantum chemical calculations are necessary to develop advanced emitter materials showing thermally-activated delayed fluorescence (TADF) for organic light-emitting diodes (OLEDs). However, calculation costs become problematic when more accurate functionals were used, therefore it is judicious to use a multimethod approach for efficiency. Here we employed combinatorial chemistry in silico to develop the deep blue TADF materials with a new concept of homo-junction design. The homo-junction materials containing TADF candidates designed by calculation were synthesized and analyzed. We found that these materials showed the emission from charge transfer (CT) state, and the clear delayed emission was provided in solid state. Because the homo-junction TADF materials showed three exponential decayed emission in solid state, we employed novel four-state kinetic analysis.

High performance from extraordinarily thick organic light-emitting diodes.

Organic light-emitting diode (OLED) technology is promising for applications in next-generation displays and lighting. However, it is difficult-especially in large-area mass production-to cover a large substrate uniformly with organic layers, and variations in thickness cause the formation of shunting paths between electrodes1,2, thereby lowering device production yield. To overcome this issue, thicker organic transport layers are desirable because they can cover particles and residue on substrates, but increasing their thickness increases the driving voltage because of the intrinsically low charge-carrier mobilities of organics. Chemical doping of organic layers increases their electrical conductivity and enables fabrication of thicker OLEDs3,4, but additional absorption bands originating from charge transfer appear5, reducing electroluminescence efficiency because of light absorption. Thick OLEDs made with organic single crystals have been demonstrated6, but are not practical for mass production. Therefore, an alternative method of fabricating thicker OLEDs is needed. Here we show that extraordinarily thick OLEDs can be fabricated by using the organic-inorganic perovskite methylammonium lead chloride, CH3NH3PbCl3 (MAPbCl3), instead of organics as the transport layers. Because MAPbCl3 films have high carrier mobilities and are transparent to visible light, we were able to increase the total thickness of MAPbCl3 transport layers to 2,000 nanometres-more than ten times the thickness of standard OLEDs-without requiring high voltage or reducing either internal electroluminescence quantum efficiency or operational durability. These findings will contribute towards a higher production yield of high-quality OLEDs, which may be used for other organic devices, such as lasers, solar cells, memory devices and sensors.

Dithia[3.3]paracyclophane Core: A Versatile Platform for Triplet State Fine-Tuning and Through-Space TADF Emission.

Thermally activated delayed fluorescence (TADF) based on through-space donor and acceptor interactions constitute a recent and promising approach to develop efficient TADF emitters. Novel TADF isomers using a dithia[3.3]-paracyclophane building block as a versatile 3D platform to promote through-space interactions are presented. Such a 3D platform allows to bring together the D and A units into close proximity and to probe the effect of their orientation, contact site and distance on their TADF emission properties. This study provides evidence that the dithia[3.3]paracyclophane core is a promising platform to control intramolecular through-space interactions and obtain an efficient TADF emission with short reverse-intersystem crossing (RISC) lifetimes. In addition, this study demonstrates that this design can tune the energy levels of the triplet states and leads to an upconversion from 3 CT to 3 LE that promotes faster and more efficient RISC to the 1 CT singlet state.

Control of the dual emission from a thermally activated delayed fluorescence emitter containing phenothiazine units in organic light-emitting diodes.

The development of single-component organic dual light-emitting molecules is of interest for a range of applications including white organic light-emitting diodes. Herein, a new thermally-activated delayed fluorescent molecule containing 4,6-bis-phenyl phenothiazine as donor units and 2-thiophene-1,3,5-triazine as acceptor unit was synthesized using a simple cost-effective method. This compound shows two stable molecular conformations due to the presence of the phenothiazine units in its molecular structure. These conformers exhibit different photophysical properties in both solution and thin films. The electroluminescence properties of this novel emitter were then examined in organic light-emitting diodes and the results provide useful insights into the influence of the device architecture on the dual emission characteristics. The experimental results were consistent with the optical simulations and the optimized architecture led to the fabrication of electroluminescent devices with an external quantum efficiency of 11.5% and a maximum luminance value of 10 370 cd m-2.

Enhanced Electroluminescence from Organic Light-Emitting Diodes with an Organic-Inorganic Perovskite Host Layer.

The development of host materials with high performance is essential for fabrication of efficient and stable organic light-emitting diodes (OLEDs). Although host materials used in OLEDs are typically organics, in this study, it is shown that the organic-inorganic perovskite CH3 NH3 PbCl3 (MAPbCl3 ) can be used as a host layer for OLEDs. Vacuum-evaporated MAPbCl3 films have a wide band gap of about 3 eV and very high and relatively balanced hole and electron mobilities, which are suitable for the host material. Photoluminescence and electroluminescence take place through energy transfer from MAPbCl3 to an organic emitter in films. Incorporation of an MAPbCl3 host layer into OLEDs leads to a reduction of driving voltage and enhancement of external quantum efficiency as compared to devices with a conventional organic host layer. Additionally, OLEDs with an MAPbCl3 host layer demonstrate very good operational stability under continuous current operation. These results can be extensively applied to organic- and perovskite-based optoelectronics.

Long-lived efficient delayed fluorescence organic light-emitting diodes using n-type hosts.

Organic light-emitting diodes have become a mainstream display technology because of their desirable features. Third-generation electroluminescent devices that emit light through a mechanism called thermally activated delayed fluorescence are currently garnering much attention. However, unsatisfactory device stability is still an unresolved issue in this field. Here we demonstrate that electron-transporting n-type hosts, which typically include an acceptor moiety in their chemical structure, have the intrinsic ability to balance the charge fluxes and broaden the recombination zone in delayed fluorescence organic electroluminescent devices, while at the same time preventing the formation of high-energy excitons. The n-type hosts lengthen the lifetimes of green and blue delayed fluorescence devices by > 30 and 1000 times, respectively. Our results indicate that n-type hosts are suitable to realize stable delayed fluorescence organic electroluminescent devices.

Toward continuous-wave operation of organic semiconductor lasers.

The demonstration of continuous-wave lasing from organic semiconductor films is highly desirable for practical applications in the areas of spectroscopy, data communication, and sensing, but it still remains a challenging objective. We report low-threshold surface-emitting organic distributed feedback lasers operating in the quasi-continuous-wave regime at 80 MHz as well as under long-pulse photoexcitation of 30 ms. This outstanding performance was achieved using an organic semiconductor thin film with high optical gain, high photoluminescence quantum yield, and no triplet absorption losses at the lasing wavelength combined with a mixed-order distributed feedback grating to achieve a low lasing threshold. A simple encapsulation technique greatly reduced the laser-induced thermal degradation and suppressed the ablation of the gain medium otherwise taking place under intense continuous-wave photoexcitation. Overall, this study provides evidence that the development of a continuous-wave organic semiconductor laser technology is possible via the engineering of the gain medium and the device architecture.

Enhanced Electroluminescence from a Thiophene-Based Insulated Molecular Wire.

We report on the realization of polymer light-emitting diodes (PLEDs) based on fluorescent polythiophene (PT)-based insulated molecular wires (IMWs). PLEDs using PT emitting layers traditionally have low external quantum efficiencies (ηeqe) below 0.1%. Moreover, IMWs lack a thorough exploitation for electroluminescent applications due to concerns about reduced charge transport between their chains. We constructed multilayer PLEDs containing PT IMW emitting layers that show the maximum ηeqe close to 1.4%, luminance at 3700 cd/m2, and low turn on voltage at 2.5 V. We also show a strong influence of the thickness of electron transport layer on ηeqe through device optimization and optical simulations.