RÉSUMÉ
Synergistic strengthening of nano-scaled M2C and ß-NiAl has become a new route to develop ultra-high secondary-hardening steel. At present, the effect of Co on the synergistic precipitation behavior of duplex phases of M2C and ß-NiAl has been rarely reported. This paper revealed the effects of Co on the mechanical properties and duplex precipitates of M2C and ß-NiAl in a novel 2.5 GPa ultra-high strength secondary-hardening steel. The tensile tests indicated that a 10% Co-alloy steel achieved a much stronger secondary-hardening effects compared to a Co-free steel during aging process, especially in the early-aging state. Needle-shaped M2C and spherical ß-NiAl particles were observed in both Co-alloy and Co-free steels. However, the number density, and volume fraction of M2C were significantly enhanced in the 10% Co-alloy steel. The Mo contents in M2C carbide and α-Fe after aging treatment were both analyzed through experimental determination and thermodynamic calculation, and the results indicated that Co decreased the solubility of Mo in α-Fe, thus promoting the precipitation of Mo-rich carbides.
RÉSUMÉ
In this work, the tensile deformation mechanisms of the Fe55Co17.5Cr12.5Ni10Mo5-xCx-based medium-entropy alloy at room temperature (R.T.), 77 K, and 4.2 K are studied. The formation of micro-defects and martensitic transformation to delay the cryogenic fracture are observed. The results show that FeCoCrNiMo5-xCx-based alloys exhibit outstanding mechanical properties under cryogenic conditions. Under an R.T. condition, the primary contributing mechanism of strain hardening is twinning-induced plasticity (TWIP), whereas at 77 K and 4.2 K, the activation of martensitic transformation-induced plasticity (TRIP) becomes the main strengthening mechanism during cryogenic tensile deformation. Additionally, the carbide precipitation along with increased dislocation density can significantly improve yield and tensile strength. Furthermore, the marked reduction in stacking fault energy (SFE) at cryogenic temperatures can promote mechanisms such as twinning and martensitic transformations, which are pivotal for enhancing ductility under extreme conditions. The Mo4C1 alloy obtains the optimal strength-ductility combination at cryogenic-to-room temperatures. The tensile strength and elongation of the Mo4C1 alloy are 776 MPa and 50.5% at R.T., 1418 MPa and 71.2% in liquid nitrogen 77 K, 1670 MPa and 80.0% in liquid helium 4.2 K, respectively.
RÉSUMÉ
Cyclic heat treatment is an effective approach for enhancing the mechanical properties of 18Ni(C250) maraging steel, and the selection of cyclic heat treatment temperature is a key factor. In this study, a cyclic heat treatment process with a two-step solution treatment is employed to investigate the influence of cyclic heat treatment temperature, specifically the first solution treatment temperature (920 °C, 950 °C, and 980 °C), on the microstructure and mechanical properties of 18Ni(C250) maraging steel. The results indicate that with an increase in the cyclic heat treatment temperature, the average grain size of the 18Ni(C250) maraging steel decreases initially and then increases. When the cyclic heat treatment temperature reaches 950 °C, the grain size is at its minimum, exhibiting optimal grain uniformity. Additionally, the increase in cyclic heat treatment temperature results in a reduction in the size of martensitic lath with the same orientation inside the grains, along with an increase in the relative quantity of low-angle grain boundaries. Furthermore, the volume fraction and size of retained austenite show a monotonous increase with the rise in the temperature of the cyclic heat treatment, and the rate of increase becomes notably larger when the temperature is raised from 950 °C to 980 °C. Based on the observed microstructural changes, the variation in the mechanical properties of the 18Ni(C250) maraging steel was analyzed. Specifically, as the cyclic heat treatment temperature increases, the tensile strength of the 18Ni(C250) maraging steel initially increases and then stabilizes, while the elongation and fracture toughness exhibit a monotonic increase.
RÉSUMÉ
Maraging steel is a prominent category of ultrahigh-strength steel (UHSS) characterized by excellent comprehensive properties, and it finds wide applications in manufacturing load-bearing structural components. In this study, a novel tungsten-containing maraging steel, C-250W, was designed. The effects of aging treatments on the mechanical properties, microstructure, precipitations, and reverted austenite of C-250W steel were investigated. The results revealed that the optimal combination of strength and toughness could be achieved through an aging treatment of C-250W steel carried out for 5 h at 480 °C after solution treatment at 1000 °C for 1 h. As the aging temperature increased, the proportion of dimples in the impact fracture gradually decreased while that of quasi-cleavage increased, leading to a reduction in Charpy impact energy. The boundary of martensitic lath decomposed gradually as the aging temperature increased, and it disappeared entirely at temperatures higher than 550 °C. Moreover, the aging process resulted in the formation of phases, including spherical Fe2M (M represents Mo, W) and thin strip-shaped Ni3N (N represents Mo, Ti) precipitates. These precipitates coarsened from 5 nm to 50-200 nm with increasing aging temperature. Additionally, the content of reverted austenite increased with the aging temperature. Within the temperature range of 400 °C to 500 °C for aging treatment, the content of film-shaped reverted austenite was approximately 3%, primarily distributed at the boundary of martensite lath. When the aging temperature exceeded 550 °C, the content of reverted austenite reached 20.2%, and its morphology changed from film-shaped to block-shaped, resulting in a decline in strength and toughness.
RÉSUMÉ
Owing to the continuous increasing of steel strength, mechanical properties including toughness and fatigue performance are becoming increasingly sensitive to inclusions in ultra-high strength steel. Rare-earth treatment is considered as an effective method to reduce the harmful effects of inclusions, but is rarely applied in secondary-hardening steel. In the present study, different amounts of cerium were added in a secondary-hardening steel to investigate the modification effect of Ce on non-metallic inclusions in steel. The characteristics of inclusions were observed experimentally using SEM-EDS and the modification mechanism was analyzed based on thermodynamic calculations. The results indicated that the main inclusions in Ce-free steel are Mg-Al-O + MgS. Thermodynamic calculation indicated that MgAl2O4 is firstly formed in liquid steel and then successively transformed into MgO and MgS during cooling process. When the Ce content is 0.0030%, the typical inclusions in steel were individual Ce2O2S and MgO + Ce2O2S complex inclusions. When the Ce content was increased to 0.0071%, the typical inclusions in steel were individual Ce2O2S- and Mg-containing inclusions. Ce treatment modifies the angular magnesium aluminum spinel inclusions into spherical and ellipsoidal Ce-containing inclusions, thus reducing the harmful effect of inclusion on steel properties.
RÉSUMÉ
Oxide metallurgy technology plays an important role in inclusion control and is also applied to improve the weldability of high strength steel. Based on the requirements of the weldability in high strength steel, the influencing factors of weld heat affected zone (HAZ) as well as the development and application status of oxide metallurgy technology are summarized in this review. Moreover, the advantages and difficulties in the application of rare earth (RE) oxide metallurgy technology are analyzed, combined with the performance mechanism of RE and its formation characteristics of fine and high melting point RE inclusions with distribution dispersed in liquid steel. With the weldability diversities of different high strength steels, the research status of weldability of high strength steel with high carbon equivalent and the effects of RE on the microstructure and properties of HAZ are discussed, and some suggestions about further research in the future are proposed.