Birds can transition between stable and unstable states via wing morphing.

Birds morph their wing shape to accomplish extraordinary manoeuvres1-4, which are governed by avian-specific equations of motion. Solving these equations requires information about a bird's aerodynamic and inertial characteristics5. Avian flight research to date has focused on resolving aerodynamic features, whereas inertial properties including centre of gravity and moment of inertia are seldom addressed. Here we use an analytical method to determine the inertial characteristics of 22 species across the full range of elbow and wrist flexion and extension. We find that wing morphing allows birds to substantially change their roll and yaw inertia but has a minimal effect on the position of the centre of gravity. With the addition of inertial characteristics, we derived a novel metric of pitch agility and estimated the static pitch stability, revealing that the agility and static margin ranges are reduced as body mass increases. These results provide quantitative evidence that evolution selects for both stable and unstable flight, in contrast to the prevailing narrative that birds are evolving away from stability6. This comprehensive analysis of avian inertial characteristics provides the key features required to establish a theoretical model of avian manoeuvrability.

Gull-inspired joint-driven wing morphing allows adaptive longitudinal flight control.

Birds dynamically adapt to disparate flight behaviours and unpredictable environments by actively manipulating their skeletal joints to change their wing shape. This in-flight adaptability has inspired many unmanned aerial vehicle (UAV) wings, which predominately morph within a single geometric plane. By contrast, avian joint-driven wing morphing produces a diverse set of non-planar wing shapes. Here, we investigated if joint-driven wing morphing is desirable for UAVs by quantifying the longitudinal aerodynamic characteristics of gull-inspired wing-body configurations. We used a numerical lifting-line algorithm (MachUpX) to determine the aerodynamic loads across the range of motion of the elbow and wrist, which was validated with wind tunnel tests using three-dimensional printed wing-body models. We found that joint-driven wing morphing effectively controls lift, pitching moment and static margin, but other mechanisms are required to trim. Within the range of wing extension capability, specific paths of joint motion (trajectories) permit distinct longitudinal flight control strategies. We identified two unique trajectories that decoupled stability from lift and pitching moment generation. Further, extension along the trajectory inherent to the musculoskeletal linkage system produced the largest changes to the investigated aerodynamic properties. Collectively, our results show that gull-inspired joint-driven wing morphing allows adaptive longitudinal flight control and could promote multifunctional UAV designs.

Thermal sensitivity of Lamb waves for structural health monitoring applications.

One of the drawbacks of the current Lamb wave structural health monitoring methods are the false positives due to changing environmental conditions such as temperature. To create an environmental insensitive damage detection scheme, the physics of thermal effects on Lamb waves must be understood. Dispersion and thermal sensitivity curves for an isotropic plate with thermal stress and thermally varying elastic modulus are presented. The thermal sensitivity of dispersion curves is analytically developed and validated by experimental measurements. The group velocity thermal sensitivity highlights temperature insensitive features at two critical frequencies. The thermal sensitivity gives us insight to how temperature affects Lamb wave speeds in different frequency ranges and will help those developing structural health monitoring algorithms.

Self-filtering oscillations in carbon nanotube hetero-junctions.

We evaluate the vibrational properties of single-wall carbon nanotube (SWCNT) hetero-junction (HJ) oscillators using a hybrid atomistic-continuum approach validated by molecular mechanics/molecular dynamics simulations. The SWCNT-HJs show a broken symmetry topology of their mode shapes, with striction effects caused on the bending and radial modes by the combined effect of the HJ and the tube with the thinner radius. The single-wall nanotube HJs also show selective mass sensing properties based solely on the geometry and type of the boundary conditions of the specific nanostructure. This unusual behaviour has not been observed so far in classical SWCNT systems.

Identification of borderline personality disorders among substance abuse inpatients.

By means of a structured interview procedure, individuals with borderline personality disorders were identified among a sample of 50 patients admitted to an inpatient substance abuse treatment program. When given a series of psychological tests, borderline patients were shown to be more pathological than a nonborderline group of substance abusers in a number of areas including depression, impulse control, antisocial tendencies and reality testing. Time spent in treatment was also shorter for the borderline group. Implications for substance abuse treatment programs and the potential impact of these patients on such programs is discussed.

Differentiation of intropunitive from extrapunitive female inmates.

Five cards of the Thematic Apperception Test were administered to 10 extrapunitive and 10 intropunitive female inmates. A scoring index based upon the individual's relationship and response to the environment was derived. Discrimination of group membership made by two independent judges who employed the index resulted in significant differentiation of groups on card 3BM. Discussion considers response to card 3BM as a manifestation of identification with the stimulus figure. Environmental constriction as an important response component also is examined.

Preparation of some immobilized linked enzyme systems and their use in the automated determination of disaccharides.

1. Glucose oxidase (EC 1.1.3.4), amyloglucosidase (EC 3.2.1.3), invertase (EC 3.2.1.26) and beta-galactosidase (EC 3.2.1.23) were covalently attached via glutaraldehyde to the inside surface of nylon tube. 2. The linked enzyme system, comprising invertase immobilized within a nylon tube acting in series with glucose oxidase immobilized in a similar way, was used for the automated determination of sucrose. 3. The linked enzyme system, comprising beta-galactosidase immobilized within a nylon tube acting in series with glucose oxidase immobilized in a similar way, was used for the automated determination of lactose. 4. The linked enzyme system, comprising amyloglucosidase immobilized within a nylon tube acting in series with glucose oxidase immobilized in a similar way, was used for the automated determination of maltose. 5. Mixtures of glucose oxidase and amyloglucosidase were immobilized within the same piece of nylon tube and used for the automated determination of maltose. 6. Mixtures of glucose oxidase and invertase were immobilized within the same piece of nylon tube and used for the automated determination of sucrose.

The immobilization of enzymes on nylon structures and their use in automated analysis.

1. Glucose oxidase (EC 1.1.3.4) and urease (EC 3.5.1.5) were covalently attached through glutaraldehyde to low-molecular-weight nylon powder. 2. Immobilized derivatives of glucose oxidase and urease were prepared by cross-linking the respective enzymes within the matrix of a nylon membrane. 3. An improved process is described for the immobilization of glucose oxidase and urease on the inside surface of partially hydrolysed nylon tube. 4. Automated analytical procedures are described for the determination of glucose with each of the three immobilized glucose oxidase derivatives and for the determination of urea with each of the three immobilized urease derivatives. 5. The efficiencies of the three immobilized enzyme structures as reagents for the automated determination of their substrates were compared.