Bonding of the silane containing multi-mode universal adhesive for lithium disilicate ceramics.

OBJECTIVES: This study evaluated the influence of a multi-mode universal adhesive (MUA) containing silane (Single Bond Universal, 3M EPSE) on the bonding of resin cement to lithium disilicate. MATERIALS AND METHODS: Thirty IPS e.max CAD specimens (Ivoclar Vivadent) were fabricated. The surfaces were treated as follows: Group A, adhesive that did not contain silane (ANS, Porcelain Bonding Resin, Bisco); Group B, silane (S) and ANS; Group C, hydrofluoric acid (HF), S, and ANS; Group D, MUA; Group E, HF and MUA. Dual-cure resin cement (NX3, Kerr) was applied and composite resin cylinders of 0.8 mm in diameter were placed on it before light polymerization. Bonded specimens were stored in water for 24 hours or underwent a 10,000 thermocycling process prior to microshear bond strength testing. The data were analyzed using multivariate analysis of variance (p < 0.05). RESULTS: Bond strength varied significantly among the groups (p < 0.05), except for Groups A and D. Group C showed the highest initial bond strength (27.1 ± 6.9 MPa), followed by Group E, Group B, Group D, and Group A. Thermocycling significantly reduced bond strength in Groups B, C, and E (p < 0.05). Bond strength in Group C was the highest regardless of the storage conditions (p < 0.05). CONCLUSIONS: Surface treatment of lithium disilicate using HF and silane increased the bond strength of resin cement. However, after thermocycling, the silane in MUA did not help achieve durable bond strength between lithium disilicate and resin cement, even when HF was applied.

Elemental analysis of caries-affected root dentin and artificially demineralized dentin.

OBJECTIVES: This study aimed to analyze the mineral composition of naturally- and artificially-produced caries-affected root dentin and to determine the elemental incorporation of resin-modified glass ionomer (RMGI) into the demineralized dentin. MATERIALS AND METHODS: Box-formed cavities were prepared on buccal and lingual root surfaces of sound human premolars (n = 15). One cavity was exposed to a microbial caries model using a strain of Streptococcus mutans. The other cavity was subjected to a chemical model under pH cycling. Premolars and molars with root surface caries were used as a natural caries model (n = 15). Outer caries lesion was removed using a carbide bur and a hand excavator under a dyeing technique and restored with RMGI (FujiII LC, GC Corp.). The weight percentages of calcium (Ca), phosphate (P), and strontium (Sr) and the widths of demineralized dentin were determined by electron probe microanalysis and compared among the groups using ANOVA and Tukey test (p < 0.05). RESULTS: There was a pattern of demineralization in all models, as visualized with scanning electron microscopy. Artificial models induced greater losses of Ca and P and larger widths of demineralized dentin than did a natural caries model (p < 0.05). Sr was diffused into the demineralized dentin layer from RMGI. CONCLUSIONS: Both microbial and chemical caries models produced similar patterns of mineral composition on the caries-affected dentin. However, the artificial lesions had a relatively larger extent of demineralization than did the natural lesions. RMGI was incorporated into the superficial layer of the caries-affected dentin.

Epigenetics: general characteristics and implications for oral health.

Genetic information such as DNA sequences has been limited to fully explain mechanisms of gene regulation and disease process. Epigenetic mechanisms, which include DNA methylation, histone modification and non-coding RNAs, can regulate gene expression and affect progression of disease. Although studies focused on epigenetics are being actively investigated in the field of medicine and biology, epigenetics in dental research is at the early stages. However, studies on epigenetics in dentistry deserve attention because epigenetic mechanisms play important roles in gene expression during tooth development and may affect oral diseases. In addition, understanding of epigenetic alteration is important for developing new therapeutic methods. This review article aims to outline the general features of epigenetic mechanisms and describe its future implications in the field of dentistry.

Effects of non-thermal atmospheric pressure pulsed plasma on the adhesion and durability of resin composite to dentin.

This study investigated the effect of low-power, non-thermal atmospheric pressure plasma (NT-APP) treatments, in pulsed and conventional modes, on the adhesion of resin composite to dentin and on the durability of the bond between resin composite and dentin. A pencil-type NT-APP jet was applied in pulsed and conventional modes to acid-etched dentin. The microtensile bond strength (MTBS) of resin composite to dentin was evaluated at 24 h and after thermocycling in one control group (no plasma) and in two experimental groups (pulsed plasma and conventional plasma groups) using the Scotchbond Multi-Purpose Plus Adhesive System. Data were analyzed using two-factor repeated-measures anova and Weibull statistics. Fractured surfaces and the bonded interfaces were evaluated using a field-emission scanning electron microscope. Although there were no significant differences between the plasma treatment groups, the plasma treatment improved the MTBS compared with the control group. After thermocycling, the MTBS did not decrease in the control or conventional plasma group but increased in the pulsed plasma group. Thermocycling increased the Weibull moduli of plasma-treated groups. In conclusion, plasma treatment using NT-APP improved the adhesion of resin composite to dentin. Using a pulsed energy source, the energy delivered to the dentin was effectively reduced without any reduction in bond strength or durability.

How to design in situ studies: an evaluation of experimental protocols.

OBJECTIVES: Designing in situ models for caries research is a demanding procedure, as both clinical and laboratory parameters need to be incorporated in a single study. This study aimed to construct an informative guideline for planning in situ models relevant to preexisting caries studies. MATERIALS AND METHODS: An electronic literature search of the PubMed database was performed. A total 191 of full articles written in English were included and data were extracted from materials and methods. Multiple variables were analyzed in relation to the publication types, participant characteristics, specimen and appliance factors, and other conditions. Frequencies and percentages were displayed to summarize the data and the Pearson's chi-square test was used to assess a statistical significance (p < 0.05). RESULTS: There were many parameters commonly included in the majority of in situ models such as inclusion criteria, sample sizes, sample allocation methods, tooth types, intraoral appliance types, sterilization methods, study periods, outcome measures, experimental interventions, etc. Interrelationships existed between the main research topics and some parameters (outcome measures and sample allocation methods) among the evaluated articles. CONCLUSIONS: It will be possible to establish standardized in situ protocols according to the research topics. Furthermore, data collaboration from comparable studies would be enhanced by homogeneous study designs.

Caries risk profile of Korean dental patients with severe intellectual disabilities.

This study evaluated the caries risk profile of patients with severe intellectual disabilities (IDs) who received dental treatment under general anesthesia. One hundred and two patients with ID [ID group, mean age (SD); 23.8(9.3)] and 100 healthy patients without ID [NID group, mean age (SD); 23.19(3.3)] were included. Medication, disability type, oral hygiene maintenance, and cooperation of the patients were investigated. Dietary habits, plaque index, mutans streptococci counts, fluoride availability, and salivary buffering were scored and analyzed using the Cariogram. The mean chance of avoiding caries (SD) was 28.1(20.4) in the ID group and 54.7(18.4) in the NID group. The ID group had significantly higher numbers of decayed and missing teeth, but fewer filled teeth than the NID group (p < .05). Significant disparities existed in the distributions of all caries-related factors except for mutans streptococci counts between the two groups (p < .05). The low chance to avoid future caries in ID patients was closely associated with insufficient oral hygiene maintenance (p < .05). Fluoride availability was strongly associated with the chance of avoiding caries in the ID group. Dental patients with severe ID exhibited a higher risk of developing caries than normal patients. Among several caries-related factors, insufficient oral hygiene maintenance and low fluoride availability most contributed to the high risk.

Evaluation of the shear bond strength of resin cement to Y-TZP ceramic after different surface treatments.

The purpose of this study was to evaluate the effect of various surface treatments on the shear bond strength of Y-TZP (Yttria-Tetragonal Zirconia Polycrystal) ceramics with zirconia primer and two different resin cements both containing 10-methacryloyloxydecyl dihydrogen phosphate (MDP). Zirconia blocks (LAVA, 3M ESPE, St. Paul, MN) were polished and assigned to five groups according to the surface treatment: (1) no further treatment (control); (2) airborne abrasion with Al2 O3 particles; (3) Z-PRIME Plus (Bisco, Schaumburg, IL) applied on polished zirconia; (4) Z-PRIME Plus applied on zirconia after airborne abrasion; and (5) tribochemical silica-coating performed with the CoJet system (3M ESPE) followed by application of ESPE®-Sil (3M ESPE). Each group was further divided into one of two resin cements: Panavia F2.0 (Kuraray, Kurashiki, Okayama, Japan) and Clearfil SA Luting (Kuraray). Resin cement placed inside a gel-cap was polymerized on the zirconia surface. Shear bond strength was tested with a universal testing machine at 0.5 mm/min. One-way analysis of variance and paired t-test were done. (p < 0.05), and scanning electron microscope (SEM) images were taken. Zirconia primer applied after airborne abrasion significantly increased the shear bond strength resulting in the highest value for both resin cements. Control groups for both cements showed the weakest value for shear bond strength. No significant differences were found between the shear bond strengths of the individual resin cements applied to zirconia surfaces treated the same way. In conclusion, the combined surface treatment of airborne abrasion followed by a zirconia primer is recommended for zirconia bonding with Panavia F2.0 and Clearfil SA Luting cements.

Thermal irritation of teeth during dental treatment procedures.

While it is reasonably well known that certain dental procedures increase the temperature of the tooth's surface, of greater interest is their potential damaging effect on the pulp and tooth-supporting tissues. Previous studies have investigated the responses of the pulp, periodontal ligament, and alveolar bone to thermal irritation and the temperature at which thermal damage is initiated. There are also many in vitro studies that have measured the temperature increase of the pulp and tooth-supporting tissues during restorative and endodontic procedures. This review article provides an overview of studies measuring temperature increases in tooth structures during several restorative and endodontic procedures, and proposes clinical guidelines for reducing potential thermal hazards to the pulp and supporting tissues.

Flexural strength and microstructure of two lithium disilicate glass ceramics for CAD/CAM restoration in the dental clinic.

OBJECTIVES: There has been a growing interest in glass ceramic systems with good esthetics, high fracture resistance and bonding durability, and simplified fabrication techniques using CAD/CAM. The aim of this study is to compare flexural strength before and after heat treatment of two lithium disilicate CAD/CAM blocks, IPS e.max CAD (Ivoclar Vivadent) and Rosetta SM (Hass), and to observe their crystalline structures. MATERIALS AND METHODS: Biaxial flexural strength was tested according to ISO 6872 with 20 disc form specimens sliced from each block before and after heat treatment. Also, the crystalline structures were observed using field-emission scanning microscopy (FE-SEM, Hitachi) and x-ray diffraction (XRD, Rigaku) analysis. The mean values of the biaxial flexural strength were analyzed by the Mann-Whitney U test at a significance level of p = 0.05. RESULTS: There were no statistically significant differences in flexural strength between IPS e.max CAD and Rosetta SM either before heat treatment or after heat treatment. For both ceramics, the initial flexural strength greatly increased after heat treatment, with significant differences (p < 0.05). The FE-SEM images presented similar patterns of crystalline structure in the two ceramics. In the XRD analysis, they also had similar patterns, presenting high peak positions corresponding to the standard lithium metasilicate and lithium disilicate at each stage of heat treatment. CONCLUSIONS: IPS e.max CAD and Rosetta SM showed no significant differences in flexural strength. They had a similar crystalline pattern and molecular composition.

Biocompatibility of mineral trioxide aggregate mixed with hydration accelerators.

INTRODUCTION: The aim of this study was to evaluate the biocompatibility of mineral trioxide aggregate mixed with selective hydration accelerators such as calcium chloride (CaCl2), citric acid (CA), and calcium lactate gluconate solution (CLG). METHODS: Inductively coupled plasma-atomic emission spectrometry analysis was used to measure calcium ions in the extracts of test materials. The 2,3-bis(2-methoxy-4-nitro-5-sulfophenyl)-5-[(phenylamino)carbonyl]-2H-tetrazolium hydroxide assay was performed using MG-63 cells to examine the cytotoxicity of the test materials. The surface of each sample and the growth pattern of the attached cells were observed using scanning electron microscopy (SEM). RESULTS: MTA mixed with 10 wt% CaCl2 and MTA mixed with 43.4 wt% CLG released a higher amount of calcium ions than the other groups. The 2,3-bis(2-methoxy-4-nitro-5-sulfophenyl)-5-[(phenylamino)carbonyl]-2H-tetrazolium hydroxide assay revealed that the cell viability of MTA mixed with 0.1 wt% CA was significantly higher than pure MTA on 7-day extract (P < .05). MTA mixed with 43.4 wt% CLG showed significantly higher cell viability than the other groups on 1-day extract (P < .05). MTA mixed with 10 wt% CaCl2 in all groups showed the lowest cell viability at all time points (P < .05). Under SEM, elongated and confluent cells were observed in all samples except in samples of MTA mixed with 10 wt% CaCl2. CONCLUSIONS: MTA mixed with 0.1 wt% CA showed good biocompatibility. MTA mixed with 43.4 wt% CLG showed favorable biocompatibility on 1 day. MTA mixed with 10 wt% CaCl2 in all groups showed the lowest cell viability at every time point and poor cell attachment under SEM.

The color change in artificial white spot lesions measured using a spectroradiometer.

OBJECTIVES: The purpose of this study was to determine the color of white spot lesions. MATERIALS AND METHODS: Human premolars were subjected to a pH cycling to produce artificial caries lesions and classified into groups (n = 10/group): group 1, immersion in deionized water; group 2, pH cycling without fluoride (F) application; group 3, pH cycling with immersion in 1,000 ppm NaF solution; and group 4, pH cycling with immersion in 5,000 ppm NaF solution. CIE L*a*b* color parameters of the tooth were determined using a spectroradiometer at baseline, after demineralization and after pH cycling. The extent of demineralization was evaluated by scanning electron microscopy (SEM) and electron microprobe analysis (EPMA). RESULTS: Significant degrees of color change (ΔE*) were observed after demineralization (p < 0.05). The changes were mainly due to an increase in lightness (L*) and a decrease in yellowness (b*). F application induced a significantly large ΔE* in group 4 (p < 0.05). The color reversal after remineralization was mostly due to the recovery of L*. SEM and EPMA verified that net mineral gains occurred in the subsurface lesions. CONCLUSIONS: The initially white appearance of enamel caries was a result of changes of L* and b*. F treatment partially restored the color of white spot lesions. CLINICAL RELEVANCE: F-driven remineralization induced both mineral gains and esthetic enhancement of artificially produced enamel white spot lesions. The increase of L* and the decrease of b* contributed to the color changes.

The influence of a continuous increase in thickness of opaque-shade composite resin on masking ability and translucency.

OBJECTIVES: This study was conducted to determine the minimum thickness of opaque-shade composite resin required to mask discolored tooth structures or darkness of the oral cavity and to determine the effect of the brand and shade of composite resins on masking ability and translucency. MATERIALS AND METHODS: Discs and beveled specimens were manufactured using six opaque-shade light-curing composite resins (Charisma, Heraeus Kulzer; Estelite Sigma Quick, Tokuyama; Gradia Direct Anterior, GC). The discolored tooth structures and darkness of the oral cavity were reproduced using background tiles. The disc specimen colors were measured using a spectroradiometer by increasing the thickness of the beveled specimens on the backing by 0.05 mm in series, and color difference (ΔE*(ab)) and translucency parameter (TP) were calculated. RESULTS: The thicknesses of opaque-shade composite resins that masked the C4 shade and black backings were 0.80-1.45 and 1.85-2.00 mm, respectively. Overall, the ΔE*(ab) and TP values decreased as the thickness of the opaque-shade composite resins increased. When the shades of the composite resins were identical, the TP decreased in the order of Charisma, Estelite Sigma Quick and Gradia Direct Anterior. When the brand was fixed, the TP was higher in the OA3 shade than in the OA2 shade. A significant correlation was seen between ΔE*(ab) and TP (p < 0.05). CONCLUSIONS: The brands and shades of the composite resins were shown to have a clear effect on TP, but an inconsistent tendency for ΔE*(ab).

Caries risk profiles of Korean dental patients using simplified Cariogram models.

OBJECTIVES: The objective of this study was to compare the caries risk profiles obtained from the simplified Cariogram models and the conventional Cariogram model of Korean dental patients. MATERIALS AND METHODS: Data required for a caries risk assessment with the Cariogram were collected from 80 young adult patients (mean: 23 years old). Three different simplified Cariogram models were produced with exclusion of either or both salivary secretion rate and lactobacilli count: group 1, conventional model; group 2, both salivary secretion rate and lactobacilli count excluded; group 3, salivary secretion rate excluded; group 4, lactobacilli count excluded. RESULTS: The mean chance of avoiding caries in group 1 (55.5%) was not significantly different from those in groups 2 and 3. Also four caries-related sectors of the Cariogram (diet, bacteria, susceptibility and circumstance) in group 1 were not significantly different than in groups 2 and 3. Group 4 showed significant differences from group 1 in the mean chance of avoiding caries and the diet, susceptibility and circumstance sectors (p < 0.05). Significant correlations were detected between all risk factors and their corresponding risk sectors (p < 0.05). Also there were significant correlations between each risk factor and the chance of avoiding caries, except for the amount of plaque, in groups 1, 2 and 3 (p < 0.05). CONCLUSIONS: The simplified Cariogram model without salivary secretion rate and lactobacilli count did not significantly change the outcome produced from the conventional model. However, single exclusion of lactobacilli count noticeably changed the caries risk profile.

Caries-preventive activity of fluoride-containing resin-based desensitizers.

OBJECTIVE: The purpose of this study was to evaluate the effects of different desensitizing agents on the prevention of root caries when applied to root surfaces. MATERIALS AND METHODS: Thirty human roots were sectioned into quarters with a 3 × 4 mm window. A desensitizer (VX, Clinpro™ XT Varnish; SP, Seal & Protect®; or PB, Clearfil™ Protect Bond) was applied to three of the quarters in each window. Teeth were stored separately in water for one day, 30 days, or 60 days. The remaining quarter, without the application of desensitizer, served as a control. After storage in water, all specimens were subjected to pH cycling. Scanning electron microscopy was used to observe the demineralization bands created on the subsurface layer. The weight percentages of fluorine (F), silica, and calcium (Ca) were determined using electron probe microanalysis to quantify the elemental distributions in the root dentin. The concentrations of F released during a pH cycling were measured. RESULTS: For the control group, the average lesion depth was 18.92 ± 5.42 µm, and the average Ca loss was 15.66% ± 6.80% in the superficial layer and 30.44% ± 9.61% in the subsurface layer. No Ca loss occurred in the desensitizer-treated groups. All desensitizing agents remained intact for at least 60 days. F levels were increased in the hybrid layer but not in the subhybrid area. Outward release of F diminished with time. CONCLUSION: The F-containing resin-based desensitizers protected exposed root surfaces from demineralization. F liberated from the desensitizers was detected only at minimal levels.

Improvement of the properties of mineral trioxide aggregate by mixing with hydration accelerators.

INTRODUCTION: Mineral trioxide aggregate (MTA) is used widely in endodontic therapy. This study examined the setting time, compressive strength, and pH of MTA mixed with several hydration accelerators (calcium chloride, low-dose citric acid, calcium lactate gluconate solution). METHODS: Group 1 (control) was obtained by mixing MTA with distilled water. In group 2, MTA containing 10% calcium chloride was mixed with distilled water. In group 3, MTA was mixed with 0.1% citric acid. In group 4, MTA was mixed with a calcium lactate gluconate solution. The setting time, compressive strength, and pH were examined. RESULTS: The setting time of MTA mixed with hydration accelerators was significantly shorter than that of MTA mixed with water (P < .01). In particular, replacing distilled water with a calcium lactate gluconate solution provided a significant decrease in setting time. The compressive strengths of MTA mixed with hydration accelerators were significantly lower than that of MTA mixed with water (P < .01), but those values increased with time. The pH of MTA mixed with hydration accelerators was significantly lower than that of MTA mixed with water (P < .01) but stable at a high level (pH 11-12). CONCLUSIONS: Hydration accelerators improved the setting time of MTA. Nevertheless, more study will be needed to improve MTA without impairing its preexisting advantages.

Chemical constitution, physical properties, and biocompatibility of experimentally manufactured Portland cement.

INTRODUCTION: An experimental Portland cement was manufactured with pure raw materials under controlled laboratory conditions. The aim of this study was to compare the chemical constitution, physical properties, and biocompatibility of experimentally manufactured Portland cement with those of mineral trioxide aggregate (MTA) and Portland cement. METHODS: The composition of the cements was determined by scanning electron microscopy (SEM) and energy-dispersive x-ray analysis (EDAX). The setting time and compressive strength were tested. The biocompatibility was evaluated by using SEM and XTT assay. RESULTS: SEM and EDAX revealed the experimental Portland cement to have a similar composition to Portland cement. The setting time of the experimental Portland cement was significantly shorter than that of MTA and Portland cement. The compressive strength of the experimental Portland cement was lower than that of MTA and Portland cement. The experimental Portland cement showed a similar biocompatibility to MTA. CONCLUSIONS: The experimental Portland cement might be considered as a possible substitute for MTA in clinical usage after further testing.

Tertiary dentin formation after direct pulp capping with odontogenic ameloblast-associated protein in rat teeth.

INTRODUCTION: Odontogenic ameloblast-associated protein (ODAM) has been shown to be specifically expressed in ameloblasts and odontoblasts and has been suggested to play a role in the mineralization of the enamel, possibly through the regulation of matrix metalloproteinase 20. However, its function in dentin is not clear. The purpose of this study was to evaluate the effect of ODAM on tertiary dentin formation. METHODS: MDPC-23 odontoblastic cells were cultured, and the effect of recombinant ODAM (rODAM) on mineralized nodule formation was evaluated. Pinpoint pulp exposures were made in rat teeth and then capped with rODAM mixed with a carrier (rODAM group), carrier only (Carrier group), or white mineral trioxide aggregate (WMTA group). After 1, 2, and 4 weeks, odontoblasts and tertiary dentin were investigated histologically and immunohistochemically. RESULTS: Nodule formation in MDPC-23 cells was enhanced by rODAM treatment. Odontoblasts were polarized and showed a palisade arrangement in the remaining pulp from the rODAM group, but not the Carrier or WMTA groups. In the WMTA group, extensive tertiary dentin along the entire pulp-dentin border obliterated the pulp chamber. In contrast, in the rODAM group, limited reaction of odontoblasts resulted in normal pulp tissue appearance without excessive tertiary dentin formation and obliteration of the pulp cavity. In the Carrier and WMTA groups, bone sialoprotein was immunostained in most of the tertiary dentin, whereas in the rODAM group, dentin sialoprotein expression was immunostained primarily in newly formed reactionary dentin. CONCLUSIONS: These results suggest that rODAM accelerates reactionary dentin formation close to the pulp exposure area, thereby preserving normal odontoblasts in the remaining pulp.

Information resources and material selection in bonded restorations among Korean dentists.

PURPOSE: To elucidate how dentists access knowledge sources when choosing adhesive agents for bonded restoration and whether these resources influenced the selection of materials. MATERIALS AND METHODS: A national survey was carried out involving dentists in South Korea. The questionnaire included the status of the operator, clinical techniques, and materials. A total of 12,193 e-mails were distributed, 2632 were opened by recipients, and 840 responses were collected. RESULTS: For primary information resources in material selection, 55.8% (n = 469) of the responders mentioned continuing education. This selection criteria varied according to the working status of the clinician (p < 0.0001). The choice of bonding system was influenced by of the length of the career (p < 0.0001), and the preferred bonding systems differed according to the source of the information (p = 0.035). CONCLUSION: The popular bonding systems were not ranked according to the bonding strategy, but a preference was found for specific brands or manufacturers. To decrease the confusion of clinicians related to the selection of bonding materials, evidence-based guidelines need to be comprehensibly organized and efficiently approached in clinics.

Two-year clinical effectiveness of adhesives and retention form on resin composite restorations of non-carious cervical lesions.

The current study investigated the clinical effectiveness of three adhesives and the use of retention form in Class V resin composite restorations of the non-carious cervical lesion (NCCL) over a two-year period. One-hundred and fifty NCCLs in 39 patients were restored with resin composites according to six experimental protocols combining the presence or absence of retention form and three adhesives: ScotchBond Multi-Purpose (MP, 3M ESPE), an experimental adhesive (EX, Vericom) and Adper Prompt (AP, 3M ESPE). All restorations were evaluated at baseline, 6, 12 and 24 months. Modified United States Public Health Service (USPHS) criteria were used to evaluate the restorations. MP was found to have significantly superior marginal adaptation than AP in cumulative logistic regression analysis (odds ratio, 2.12; 95% confidence interval, 1.05-4.31; p = 0.0397). In analysis using the Pearson's Chi-square or Fisher's Exact Test to compare the clinical performance of restorations with and without retention form, EX with retention form showed a significantly higher retention rate at two years than that without retention form (p = 0.0089). Restorations with retention form also showed significantly less marginal discoloration than those without retention form in all three adhesives (p = 0.0336).

Nuclear factor I-C is essential for odontogenic cell proliferation and odontoblast differentiation during tooth root development.

Our previous studies have demonstrated that nuclear factor I-C (NFI-C) null mice developed short molar roots that contain aberrant odontoblasts and abnormal dentin formation. Based on these findings, we performed studies to elucidate the function of NFI-C in odontoblasts. Initial studies demonstrated that aberrant odontoblasts become dissociated and trapped in an osteodentin-like mineralized tissue. Abnormal odontoblasts exhibit strong bone sialoprotein expression but a decreased level of dentin sialophosphoprotein expression when compared with wild type odontoblasts. Loss of Nfic results in an increase in p-Smad2/3 expression in aberrant odontoblasts and pulp cells in the subodontoblastic layer in vivo and primary pulp cells from Nfic-deficient mice in vitro. Cell proliferation analysis of both cervical loop and ectomesenchymal cells of the Nfic-deficient mice revealed significantly decreased proliferative activity compared with wild type mice. In addition, Nfic-deficient primary pulp cells showed increased expression of p21 and p16 but decreased expression of cyclin D1 and cyclin B1, strongly suggesting cell growth arrest caused by a lack of Nfic activity. Analysis of the pulp and abnormal dentin in Nfic-deficient mice revealed an increase in apoptotic activity. Further, Nfic-deficient primary pulp cells exhibited an increase in caspase-8 and -3 activation, whereas the cleaved form of Bid was hardly detected. These results indicate that the loss of Nfic leads to the suppression of odontogenic cell proliferation and differentiation and induces apoptosis of aberrant odontoblasts during root formation, thereby contributing to the formation of short roots.