The effect of manufacturing variables on radiation doses from porcelain tiles.

Previous studies have focused on the radiological properties of glazed ceramic tiles. This study was conducted to describe the radiological properties of porcelain tiles and how they were affected by variations in the manufacturing parameters. The data showed that the majority of the uranium in the tiles was attributable to the addition of zircon while less than half of the thorium in the tile was attributable to the added zircon, and the remainder came from other minerals in the formulation. The effects of firing temperatures and compressive strengths of the tiles are presented and show that higher firing temperatures increase radon emanation, while higher compressive strengths reduce radon emanation. The study also described how the addition of zircon to the tile formulation affected the radiological exposures that could be received by a member of the public from the use of such porcelain tiles. A dose assessment was conducted based on 23 different types of tile formulation. Screening procedures for building materials have been described in European Commission documents, and these limit the addition of zircon in a porcelain tile to approximately 9% by mass. The dose assessment reported in this study showed that 20% zircon could be added to a porcelain tile without exceeding the prescribed dose limits.

Measurement of the equilibrium factor between radon and its progeny in the underground mining environment.

A scintillation cell and a portable radiation spectrometer for radon progeny were respectively employed to measure the concentration of radon and that of its progeny in the underground gold mine environment. The measured concentrations were subsequently used to calculate the equilibrium factor between radon and its progeny. The results obtained indicate that various locations underground have different values of radon concentration and ratios of radon concentration to its progeny concentration. The differences can be ascribed to variations in grades of uranium at different locations and to some environmental factors such as ventilation, particle concentration, and the deposition of the progeny on surfaces or on the atmospheric aerosol.

Diversion of water flow from a floodplain wetland stream: an analysis of geomorphological setting and hydrological and ecological consequences.

Diversion of water has been ongoing in the Mkuze Wetland for several decades. Two canals form the focus of this study; the Mpempe-Demazane Canal and the Tshanetshe Canal. The former involved an ambitious excavation over a distance of 13.5 km in the lower part of the wetland, while the latter was a minor excavation over a distance of approximately 100 m in the upper part of the wetland. Although ambitious and costly, the Mpempe-Demazane Canal resulted in little downward or headward erosion, and there was minor diversion of flow. However, the minor excavation of the Tshanetshe Canal resulted in erosion downstream of the excavation (the Tshanetshe Stream), downward and lateral erosion of the excavated section, and headward erosion that has propagated almost 4 km upstream along the Mkuze River. Most of the flow of the Mkuze River has been captured by the Tshanetshe Canal and Stream. The impact of canalisation on floodplain wetlands is thus more dependent on the location than the scale of activity. The avulsion of the Mkuze River into the Tshanetshe Canal and Stream is due to a large difference in elevation between the Mkuze River and floodplain into which it was diverted, and the fact that in this region the river typically has high discharges. This avulsion may have been inevitable as a result of natural processes of sedimentation. In contrast, the difference in elevation between the Mkuze River and the basin into which it was diverted via the Mpempe Canal was small as is discharge of the Mkuze River in this part of the wetland. Thus, the diversion was unsuccessful. The presence of hippos that create hydraulically efficient pathways that are oriented parallel to the regional hydraulic slope, may accelerate avulsion in large African wetlands. Overall, it is argued that the environmental consequences of excavation need to be viewed against the background that wetlands are dynamic features within the landscape.

Combining UASB technology and advanced oxidation processes (AOPs) to treat food processing wastewaters.

UASB treatment of fruit cannery and winery effluents was shown to be feasible. However, the treated effluents still have residual COD levels well above the legal limit of 75 mg.l(-1) for direct discharge to a water system and a form of post-treatment is necessary to reduce the COD further. Ozone and ozone/hydrogen peroxide were used in combination with a granular activated carbon contacting column to assess the effectiveness as a post-treatment option for the UASB treated fruit cannery and winery effluent. Colour reduction in the effluents ranged from 66 to 90% and COD reductions of 27-55% were achieved. The combination of ozone and hydrogen peroxide gave better results than ozonation alone. Significant progress was thus made in achieving the legal limit of 75 mg.l(-1).

Use of ozone and hydrogen peroxide in the post-treatment of UASB treated alkaline fruit cannery effluent.

UASB treatment of cannery effluents was shown to be feasible. However, the treated effluent still does not allow direct discharge to a water system and a further form of post-treatment is necessary to reduce the COD to lower than the legal limit of 75 mg/l. The use of ozone, hydrogen peroxide and granular activated carbon were used singly or in combination to assess the effectiveness as post-treatment options for the UASB treated alkaline fruit cannery effluent. Colour reduction in the effluent ranged from 15% to 92% and COD reductions of 26-91% were achieved. Combinations of ozone and hydrogen peroxide gave better results than either oxidant singly. The best results were achieved by combining ozone, hydrogen peroxide and granular activated carbon, and COD levels were reduced to levels sufficiently below the 75 mg/l limit.

The measurement of activity-weighted size distributions of radon progeny: methods and laboratory intercomparison studies.

Over the past 5 y, there have been significant improvements in measurement of activity-weighted size distributions of airborne radon decay products. The modification of screen diffusion batteries to incorporate multiple screens of differing mesh number, called graded screen arrays, have permitted improved size resolution below 10 nm such that the size distributions can now be determined down to molecular sized activities (0.5 nm). In order to ascertain the utility and reliability of such systems, several intercomparison tests have been performed in a 2.4 m3 radon chamber in which particles of varying size have been produced by introducing SO2 and H2O along with the radon to the chamber. In April 1988, intercomparison studies were performed between direct measurements of the activity-weighted size distributions as measured by graded screen arrays and an indirect measurement of the distribution obtained by measuring the number size distribution with a differential mobility analyzer and multiplying by the theoretical attachment rate. Good agreement was obtained in these measurements. A second set of intercomparison studies among a number of groups with graded screen array systems was made in April 1989 with the objective of resolving spectral structure below 10 nm. Again, generally good agreement among the various groups was obtained although some differences were noted. It is thus concluded that such systems can be constructed and can be useful in making routine measurements of activity-weighted size distributions with reasonable confidence in the results obtained.