Low Operating Voltage Carbon-Graphene Hybrid E-textile for Temperature Sensing.

Graphene-coated polypropylene (PP) textile fibers are presented for their use as temperature sensors. These temperature sensors show a negative thermal coefficient of resistance (TCR) in a range between 30 and 45 °C with good sensitivity and reliability and can operate at voltages as low as 1 V. The analysis of the transient response of the temperature on resistance of different types of graphene produced by chemical vapor deposition (CVD) and shear exfoliation of graphite (SEG) shows that trilayer graphene (TLG) grown on copper by CVD displays better sensitivity due to the better thickness uniformity of the film and that carbon paste provides good contact for the measurements. Along with high sensitivity, TLG on PP shows not only the best response but also better transparency, mechanical stability, and washability compared to SEG. Temperature-dependent Raman analysis reveals that the temperature has no significant effect on the peak frequency of PP and expected effect on graphene in the demonstrated temperature range. The presented results demonstrate that these flexible, lightweight temperature sensors based on TLG with a negative TCR can be easily integrated in fabrics.

Water-Based Solution Processing and Wafer-Scale Integration of All-Graphene Humidity Sensors.

One of the main advantages of 2D materials for various applications is that they can be prepared in form of water-based solutions. The high yield and cost-effectiveness of this method make them of great interest for printed electronics, composites, and bio- and healthcare technologies. However, once deposited on a substrate, etching away these solution-processed materials is a difficult task, yet crucial for pattern definition and thus device fabrication. In particular, the realization of micrometer-sized patterns requires mesh and paste optimization when screen-printed or solvent-engineered and surface functionalization when inkjet-printed, both usually involving additional postdeposition steps. These constraints are holding back the integration of these 2D materials in devices and applications. In this work, a method for the fabrication of micrometer-sized well-defined patterns in water-based 2D materials is presented, with an extensive characterization of the films and patterns obtained. The method is ultimately used to create humidity sensors with performance comparable to that of commercial ones. These sensor devices are fabricated onto a 4' silicon and polyethylene terephthalate (PET) wafers to create all-graphene humidity sensors that are flexible, transparent, and compatible with current complementary metal-oxide-semiconductor (CMOS) and roll-to-roll workflows.

Fast and Highly Sensitive Ionic-Polymer-Gated WS2 -Graphene Photodetectors.

The combination of graphene with semiconductor materials in heterostructure photodetectors enables amplified detection of femtowatt light signals using micrometer-scale electronic devices. Presently, long-lived charge traps limit the speed of such detectors, and impractical strategies, e.g., the use of large gate-voltage pulses, have been employed to achieve bandwidths suitable for applications such as video-frame-rate imaging. Here, atomically thin graphene-WS2 heterostructure photodetectors encapsulated in an ionic polymer are reported, which are uniquely able to operate at bandwidths up to 1.5 kHz whilst maintaining internal gain as large as 106 . Highly mobile ions and the nanometer-scale Debye length of the ionic polymer are used to screen charge traps and tune the Fermi level of the graphene over an unprecedented range at the interface with WS2 . Responsivity R = 106 A W-1 and detectivity D* = 3.8 × 1011 Jones are observed, approaching that of single-photon counters. The combination of both high responsivity and fast response times makes these photodetectors suitable for video-frame-rate imaging applications.

Homogeneously Bright, Flexible, and Foldable Lighting Devices with Functionalized Graphene Electrodes.

Alternating current electroluminescent technology allows the fabrication of large area, flat and flexible lights. Presently the maximum size of a continuous panel is limited by the high resistivity of available transparent electrode materials causing a visible gradient of brightness. Here, we demonstrate that the use of the best known transparent conductor FeCl3-intercalated few-layer graphene boosts the brightness of electroluminescent devices by 49% compared to pristine graphene. Intensity gradients observed for high aspect ratio devices are undetectable when using these highly conductive electrodes. Flat lights on polymer substrates are found to be resilient to repeated and flexural strains.