RÉSUMÉ
Accurate and temporally consistent measurements of light absorbing aerosol (LAA) heating rate (HR) and of its source apportionment (fossil-fuel, FF; biomass-burning, BB) and speciation (black and brown Carbon; BC, BrC) are needed to evaluate LAA short-term climate forcing. For this purpose, wavelength- and time-dependent accurate LAA absorption coefficients are required. HR was experimentally determined and apportioned (sources/species) in the EMEP/ACTRIS/COLOSSAL-2018 winter campaign in Milan (urban-background site). Two Aethalometers (AE31/AE33) were installed together with a MAAP, CPC, OPC, a low volume sampler (PM2.5) and radiation instruments. AE31/AE33 multiple-scattering correction factors (C) were determined using two reference systems for the absorption coefficient: 1) 5-wavelength PP_UniMI with low time resolution (12 h, applied to PM2.5 samples); 2) timely-resolved MAAP data at a single wavelength. Using wavelength- and time-independent C values for the AE31 and AE33 obtained with the same reference device, the total HR showed a consistency (i.e. reproducibility) with average values comparable at 95% probability. However, if different reference devices/approaches are used, i.e. MAAP is chosen as reference instead of a PP_UniMI, the HR can be overestimated by 23-30% factor (by both AE31/AE33). This became more evident focusing on HR apportionment: AE33 data (corrected by a wavelength- and time-independent C) showed higher HRFF (+24 ± 1%) and higher HRBC (+10 ± 1%) than that of AE31. Conversely, HRBB and HRBrC were -28 ± 1% and -29 ± 1% lower for AE33 compared to AE31. These inconsistencies were overcome by introducing a wavelength-dependent Cλ for both AE31 and AE33, or using multi-wavelength apportionment methods, highlighting the need for further studies on the influence of wavelength corrections for HR determination. Finally, the temporally-resolved determination of C resulted in a diurnal cycle of the HR not statistically different whatever the source- speciation- apportionment used.
Sujet(s)
Polluants atmosphériques , Chauffage , Aérosols/analyse , Polluants atmosphériques/analyse , Carbone/analyse , Surveillance de l'environnement , Matière particulaire , Reproductibilité des résultatsRÉSUMÉ
Particulate matter (PM) is acknowledged to have multiple detrimental effects on human health. In this review, we report literature results on the possible link between outdoor PM and health outcomes with a focus on pulmonary infections and the mechanisms responsible for observed negative effects. PM physical and chemical properties, such as size and chemical composition, as well as major emission sources are described for a more comprehensive view about the role played by atmospheric PM in the observed adverse health effects; to this aim, major processes leading to the deposition of PM in the respiratory tract and how this can pave the way to the onset of pathologies are also presented. From the literature works here reviewed, two ways in which PM can threaten human health promoting respiratory infectious diseases are mostly taken into account. The first pathway is related to an enhanced susceptibility and here we will also report on molecular mechanisms in the lung immune system responsible for the augmented susceptibility to pathogens, such as the damage of mechanical defensive barriers, the alteration of the innate immune response, and the generation of oxidative stress. The second one deals with the relationship between infectious agents and PM; here we recall that viruses and bacteria (BioPM) are themselves part of atmospheric PM and are collected during sampling together with particles of different origin; so, data should be analysed with caution in order to avoid any false cause-effect relation. To face these issues a multidisciplinary approach is mandatory as also evident from the ongoing research about the mechanisms hypothesized for the SARS-CoV-2 airborne spreading, which is still controversial and claims for further investigation. Therefore, we preferred not to include papers dealing with SARS-CoV-2.
Sujet(s)
Polluants atmosphériques , COVID-19 , Pneumopathie infectieuse , Polluants atmosphériques/analyse , Polluants atmosphériques/toxicité , Humains , Poumon , Taille de particule , Matière particulaire/analyse , Matière particulaire/toxicité , SARS-CoV-2RÉSUMÉ
In this work PM2.5 was collected during winter and summer in a Sardinian village (Gonnostramatza, Italy) highly affected by biomass burning emissions. A multi-technique approach was adopted for the complete PM chemical characterization. The bulk characterization was performed by IC (Ion Chromatography), HPAEC (High-Performance Anion-Exchange Chromatography), TOT (Thermal Optical Transmittance) and ED-XRF (Energy-Dispersive X-Ray Fluorescence) while XPS (X-ray Photoelectron Spectroscopy) was used for the surface characterization. Using levoglucosan as specific tracer of biomass burning emissions, the assessment of the impact of this source was carried out and it represent the major PM source at the investigate site during winter. In winter the average levoglucosan concentration is 2096⯱â¯324â¯ng/m3 while during summer its concentration is negligible (18⯱â¯7â¯ng/m3). Levoglucosan content in PM2.5 during winter is on average 13.7%; it is estimated that 65% of PM2.5 is due to wood burning. XPS has been exploited in this work aiming at highlighting possible differences between surface and bulk composition of PM2.5. The surface of the particulate matter resulted enriched in carbon compared to the bulk. Among the components of XPS C1s signals recorded on the samples collected during winter, it was found that the signal at 286.5â¯eV, which is due to the presence of COH, reflects the bulk composition of levoglucosan.
Sujet(s)
Polluants atmosphériques/analyse , Carbone/analyse , Surveillance de l'environnement , Matière particulaire/analyse , Bois/composition chimique , Italie , SaisonsRÉSUMÉ
In this paper, results from receptor modelling performed on a well-characterised PM1 dataset were combined to chemical light extinction data (bext) with the aim of assessing the impact of different PM1 components and sources on light extinction and visibility at a European polluted urban area. It is noteworthy that, at the state of the art, there are still very few papers estimating the impact of different emission sources on light extinction as we present here, although being among the major environmental challenges at many polluted areas. Following the concept of the well-known IMPROVE algorithm, here a tailored site-specific approach (recently developed by our group) was applied to assess chemical light extinction due to PM1 components and major sources. PM1 samples collected separately during daytime and nighttime at the urban area of Milan (Italy) were chemically characterised for elements, major ions, elemental and organic carbon, and levoglucosan. Chemical light extinction was estimated and results showed that at the investigated urban site it is heavily impacted by ammonium nitrate and organic matter. Receptor modelling (i.e. Positive Matrix Factorization, EPA-PMF 5.0) was effective to obtain source apportionment; the most reliable solution was found with 7 factors which were tentatively assigned to nitrates, sulphates, wood burning, traffic, industry, fine dust, and a Pb-rich source. The apportionment of aerosol light extinction (bext,aer) according to resolved sources showed that considering all samples together nitrate contributed at most (on average 41.6%), followed by sulphate, traffic, and wood burning accounting for 18.3%, 17.8% and 12.4%, respectively.
Sujet(s)
Surveillance de l'environnement/méthodes , Matière particulaire/analyse , Lumière du soleil , Aérosols/analyse , Polluants atmosphériques/analyse , Poussière/analyse , Pollution de l'environnement/statistiques et données numériques , Industrie , Italie , Nitrates/analyse , Sulfates , Bois/composition chimiqueRÉSUMÉ
In this work, a comprehensive characterisation and source apportionment of size-segregated aerosol collected using a multistage cascade impactor was performed. The samples were collected during wintertime in Milan (Italy), which is located in the Po Valley, one of the main pollution hot-spot areas in Europe. For every sampling, size-segregated mass concentration, elemental and ionic composition, and levoglucosan concentration were determined. Size-segregated data were inverted using the program MICRON to identify and quantify modal contributions of all the measured components. The detailed chemical characterisation allowed the application of a three-way (3-D) receptor model (implemented using Multilinear Engine) for size-segregated source apportionment and chemical profiles identification. It is noteworthy that - as far as we know - this is the first time that three-way source apportionment is attempted using data of aerosol collected by traditional cascade impactors. Seven factors were identified: wood burning, industry, resuspended dust, regional aerosol, construction works, traffic 1, and traffic 2. Further insights into size-segregated factor profiles suggested that the traffic 1 factor can be associated to diesel vehicles and traffic 2 to gasoline vehicles. The regional aerosol factor resulted to be the main contributor (nearly 50%) to the droplet mode (accumulation sub-mode with modal diameter in the range 0.5-1 µm), whereas the overall contribution from the two factors related to traffic was the most important one in the other size modes (34-41%). The results showed that applying a 3-D receptor model to size-segregated samples allows identifying factors of local and regional origin while receptor modelling on integrated PM fractions usually singles out factors characterised by primary (e.g. industry, traffic, soil dust) and secondary (e.g. ammonium sulphate and nitrate) origin. Furthermore, the results suggested that the information on size-segregated chemical composition in different size classes was exploited by the model to relate primary emissions to rapidly-formed secondary compounds.
Sujet(s)
Aérosols/analyse , Polluants atmosphériques/analyse , Surveillance de l'environnement/méthodes , Matière particulaire/analyse , Poussière/analyse , Pollution de l'environnement , Essence , Italie , Nitrates , Taille de particule , Bois/composition chimiqueRÉSUMÉ
Advanced receptor models have been recently developed and tested in order to improve the resolution of apportionment problems reducing rotational ambiguity of results and aiming at identifying a larger number of sources. In particular, multi-time model is a factor analysis method able to compute source profiles and contributions using aerosol compositional data with different time resolutions. Unlike traditional factor analysis, each measured value can be inserted into multi-time model with its original time schedule, thus all temporal information can be effectively used in the modelling process. In this work, multi-time model was expanded in order to impose constraints on modelled factors aiming at improving the source identification. Moreover, as far as we know for the first time, a suitable bootstrap technique was implemented in the multi-time scheme to estimate the uncertainty of the final constrained solutions. These implemented approaches were tested on a PM2.5 (particulate matter with aerodynamic diameter <2.5 µm) dataset composed of 24-h samples collected during one year and hourly data sampled in parallel for two shorter periods in Florence (Italy). The daily samples were chemically characterised for elements, ions and carbonaceous components while elemental concentrations only were available for high-time resolved samples. The application of the advanced model revealed the major contribution from traffic (accounting for 37% of PM2.5 as annual average) and allowed an accurate characterisation of involved emission processes. In particular, exhaust and non-exhaust emissions were identified. The constraints imposed in the continuation run led to a better description of the factor associated to nitrates and also of biomass burning profile and the bootstrap results gave useful information to assess the reliability of source apportionment solutions. Finally, the comparison with the results computed by ME-2 base model applied to daily and hourly compositional data separately demonstrated the advantages provided by the multi-time approach.
RÉSUMÉ
In this study, the Multilinear Engine (ME-2) receptor model was applied to speciated particulate matter concentration data collected with two different measuring instruments upwind and downwind of a steelworks complex in Port Talbot, South Wales, United Kingdom. Hourly and daily PM samples were collected with Streaker and Partisol samplers, respectively, during a one month sampling campaign between April 18 and May 16, 2012. Daily samples (PM10, PM2.5, PM2.5-10) were analysed for trace metals and water-soluble ions using standard procedures. Hourly samples (PM2.5 and PM2.5-10) were assayed for 22 elements by Particle Induced X-ray Emission (PIXE). PM10 data analysis using ME-2 resolved 6 factors from both datasets identifying different steel processing units including emissions from the blast furnaces (BF), the basic oxygen furnace steelmaking plant (BOS), the coke-making plant, and the sinter plant. Steelworks emissions were the main contributors to PM10 accounting for 45% of the mass when including also secondary aerosol. The blast furnaces were the largest emitter of primary PM10 in the study area, explaining about one-fifth of the mass. Other source contributions to PM10 were from marine aerosol (28%), traffic (16%), and background aerosol (11%). ME-2 analysis was also performed on daily PM2.5 and PM2.5-10 data resolving 7 and 6 factors, respectively. The largest contributions to PM2.5-10 were from marine aerosol (30%) and blast furnace emissions (28%). Secondary components explained one-half of PM2.5 mass. The influence of steelworks sources on ambient particulate matter at Port Talbot was distinguishable for several separate processing sections within the steelworks in all PM fractions.
Sujet(s)
Polluants atmosphériques/analyse , Pollution de l'air/statistiques et données numériques , Surveillance de l'environnement , Métallurgie , Modèles chimiques , Matière particulaire/analyse , Acier , Pays de GallesRÉSUMÉ
An example of an integrated approach to assess air pollution threats to cultural heritage in a semi-confined environment is presented in this work, where the monitoring campaign carried out at the Michelozzo's Courtyard (in Palazzo Vecchio, Florence, Italy) is used as a case study. A wide research project was carried out, with the main aim of obtaining the first quantitative data on air quality and microclimate conditions inside the Courtyard, and, if possible, identifying the main causes of degradation and suggesting appropriate conservation strategies. The investigation adopted a holistic approach involving thermographic measurements on the wall paintings, microclimatic analysis, gaseous pollutant monitoring, atmospheric particles characterisation and dry deposition compositional analysis. Attention was focused on the wall painting depicting the city of Hall because of its anomalous and critical conservation conditions, which are visible at a glance, due to the contrast between a wide darker zone around the central subject of the painting and external lighter areas.
Sujet(s)
Polluants atmosphériques/analyse , Atmosphère/composition chimique , Espaces restreints , Culture (sociologie) , Surveillance de l'environnement/méthodes , Matière particulaire/analyse , Pollution de l'air/prévention et contrôle , Calcium/analyse , Italie , Dioxyde d'azote/analyse , Ozone/analyse , Peintures (art) , Silicium/analyse , Soufre/analyseRÉSUMÉ
Daily time series measurements of elements or compounds are widely used to apportion the contribution of specific sources of particulate matter concentration in the atmosphere. We present results obtained for the urban area of Genoa (Italy) based on several hundred of PM10, PM2.5 and PM1 daily samples collected in sites with different geo-morphological and urbanization characteristics. Elemental concentrations of Na to Pb were obtained through Energy Dispersive X-Ray Fluorescence (ED-XRF), and the contributions of specific sources of particulate matter (PM) concentration were apportioned through Positive Matrix Factorization (PMF). By sampling at different sites we were able to obtain, in each PM fraction, the average and stable values for the tracers of specific sources, in particular traffic (Cu, Zn, Pb) and heavy oil combustion (V, Ni). We could also identify and quote the contamination of anthropogenic PM in "natural" sources (sea, soil dust). Sampling at several sites in the same urban area allowed us to resolve local characteristics as well as to quote average values.
Sujet(s)
Polluants atmosphériques/analyse , Surveillance de l'environnement , Métaux/analyse , Matière particulaire/analyse , Emissions des véhicules/analyse , Mouvements de l'air , Villes , Cuivre/analyse , Géographie , Italie , Plomb/analyse , Nickel/analyse , Taille de particule , Sodium/analyse , Spectrométrie d'émission X , Facteurs temps , Vanadium/analyse , Zinc/analyseRÉSUMÉ
The particulate matter (PM) concentration and composition, the PM10, PM2.5, PM1 fractions, were studied in the urban area of Genoa, a coastal town in the northwest of Italy. Two instruments, the continuous monitor TEOM and the sequential sampler PARTISOL, were operated almost continuously on the same site from July 2001 to September 2004. Samples collected by PARTISOL were weighted to obtain PM concentration and then analysed by PIXE (particle induced X-ray emission) and by ED-XRF (energy dispersion X-ray fluorescence), obtaining concentrations for elements from Na to Pb. Some of the filters used in the TEOM microbalance were analysed by ED-XRF to calculate Pb concentration values averaged over 7-30 d periods.
Sujet(s)
Polluants atmosphériques/analyse , Surveillance de l'environnement , Villes , Italie , Taille de particule , SaisonsRÉSUMÉ
Weekly measurements of 210Pb activity concentration on aerosol particles were performed at ground level in outdoor air in Milan (Italy) during the years 2000-2001. The experimental method was based on the delayed alpha spectrometry of in-grown 210Po activity detected on airborne particles collected on a filter support. On the same filter the 214Pb activity concentration was also measured during the sampling. 210Pb weekly concentration values showed a great variability and the average monthly values exhibited a seasonal pattern characterised by maxima in winter and minima in spring-summer. The same seasonal trend was also observed in 214Pb concentration values. 210Pb average yearly values were 0.70 and 0.82 mBq/m3 in 2000 and 2001, respectively, in good agreement with literature data registered at continental sites of similar latitude and longitude. The activity ratio 210Pb/214Pb was used to evaluate the residence time of fine aerosols in the urban air of Milan, which was 1-2 days.
Sujet(s)
Aérosols/analyse , Polluants atmosphériques radioactifs/analyse , Radio-isotopes du plomb/analyse , Polonium/analyse , Saisons , Surveillance de l'environnement , Italie , RadonRÉSUMÉ
In this paper a source apportionment of particulate matter pollution in the urban area of Milan (Italy) is given. Results of PM10 and PM2.5 mass and elemental concentrations from a 1-year monitoring campaign are presented. Mean annual and daily PM10 levels are compared with the limits of the EU Air Quality Directive EC/30/1999 and the results show that the limit values established would not be met in the urban area of Milan or the large surrounding area. Moreover, high levels of PM2.5 are registered and this fraction constitutes a high portion of the PM10 mass. In Milan the winter period is characterised by a high degree of air pollution due to a greater contribution of emissions and to adverse meteorological and thermodynamic conditions of the atmosphere. The application of multivariate techniques and receptor modelling (PCFA, APCFA) to the whole data-set led to the identification of the main emitting sources and to the source apportionment of PM10 and PM2.5 in Milan. The most important sources were identified as 'soil dust', 'traffic', 'industry' and 'secondary compounds' for PM10 and as 'soil dust', 'anthropogenic' and 'secondary compounds' for PM2.5, explaining the greatest part of the total variance (91% and 75%, respectively).
RÉSUMÉ
Continuous measurement of hourly concentrations of 212Pb attached to aerosol particles was carried out during the whole year 2000 in the outdoor air of Milan (Italy). An improved experimental method based on on-line alpha spectroscopy during atmospheric particulate matter sampling allowed the contemporary determination of 212Pb and 214Bi through the deconvolution of the alpha energy spectral distribution analysis. The 212Pb hourly concentrations were about 100 times lower than 214Bi but showed a similar characteristic diurnal time trend. However, the influence of meteorological parameters such as rain and wind was more evident in 212Pb than in 214Bi concentrations. The 212Pb average annual concentration was 0.090 +/- 0.060 Bq/m3 with daily mean concentration varying from 0.013 to 0.333 Bq/m3.
Sujet(s)
Pollution de l'air intérieur/analyse , Bismuth/analyse , Radio-isotopes du plomb/analyse , Radio-isotopes/analyse , Aérosols , Villes , Surveillance de l'environnement , Italie , Taille de particule , Analyse spectrale , Facteurs tempsRÉSUMÉ
Results obtained during a winter field campaign for the fine fractions of particulate matter are presented. A high pollution episode together with an analysis of the main factors, which influence accumulation of pollutants is described. The measurement campaigns were carried out simultaneously at two sites in Northern Italy, Milan and Erba, during the winter of 2000. The daily variability in the mass concentration values and PM2.5/PM10 ratios appeared to be strongly dependent upon meteorological and atmospheric stability conditions and, in particular, wind regimes. During the intensive field campaign a high-pollution episode occurred that led to TSP and fine fraction concentrations well above the attention and alarm thresholds, reaching values of up to 200-250 microg m(-3). The elemental concentrations were determined by ED-XRF analysis. The elemental composition of the particulate matter indicated that crustal matter oxides (soil dust) were the main component in particles with aerodynamic diameter d(ae) > 10 microm. They were an important part also in particles with 2.5 < d(ae) < 10 microm, but strongly decreased in particles with d(ae) < 2.5 microm. In the finer fraction sulphates nitrogen and carbon compounds played a major role. The temporal patterns of mass and elemental concentrations, as well as the main components of PM were very similar at the two sites. The high-pollution episode was recorded at many locations in the Po plain, highlighting the role of meteorology and thermodynamic atmospheric conditions on pollution build-up on a large area.
Sujet(s)
Aérosols , Polluants atmosphériques/analyse , Villes , Surveillance de l'environnement , Italie , Concepts météorologiques , Taille de particule , Saisons , ThermodynamiqueRÉSUMÉ
Transgenic FVB-NeuN mice (N202) bearing the rat neu protooncogene driven by the mouse mammary tumor virus promoter/enhancer develop focal mammary carcinomas overexpressing the neu-encoded p185(neu) protein. In vitro expression of p185(neu) among mammary carcinoma cultures was heterogeneous, and we could establish some cell lines and clones displaying a complete loss of p185(neu) expression, along with others with very high p185(neu) protein level. Upon in vivo injection, p185(neu)-positive cells gave rise to fast-growing tumors with a short latency, while p185(neu)-negative cells required a very long latency time, and the resulting tumors were invariably p185(neu)-positive. The lower growth ability of p185(neu)-negative cells in vivo was also confirmed in athymic nude mice. In vitro, analysis of anchorage-independent growth in soft agar revealed colony formation from p185(neu)-positive but not p185(neu)-negative cells. The direct involvement of p185(neu) in clonogenicity was demonstrated by the inhibition of p185(neu)-positive colony growth in soft agar in the presence of an anti-p185(neu) monoclonal antibody. By contrast, a higher level of anchorage-dependent clonogenic growth and proliferation was observed in p185(neu)-negative cells as compared to p185(neu)-positive cells, thus explaining the relative ease with which p185(neu)-negative cell lines and clones were established in vitro. Together, the results indicate that p185(neu) expression can lead to tumor formation and metastasis through the modification of intrinsic properties of cells related to anchorage-independent growth ability rather than to proliferation or host-dependent mechanisms.
Sujet(s)
Tumeurs expérimentales de la mamelle/génétique , Tumeurs expérimentales de la mamelle/métabolisme , Récepteur ErbB-2/génétique , Récepteur ErbB-2/physiologie , Animaux , Anticorps monoclonaux , Technique de Northern , Technique de Western , Adhérence cellulaire , Division cellulaire , Cellules cultivées , Clonage moléculaire , Femelle , Cytométrie en flux , Souris , Souris transgéniques , Tests aux précipitines , Régions promotrices (génétique) , Rats , Récepteur ErbB-2/biosynthèse , Facteurs temps , Cellules cancéreuses en cultureRÉSUMÉ
We investigated the in vitro and in vivo effects of the ectopic expression of the pRb2/p130 cell cycle regulator on c-erbB-2-associated tumorigenicity. SKOV3 ovarian cancer cells, which display c-erbB-2 gene amplification and oncoprotein (p185HER2) overexpression, were stably transfected with a plasmid containing the coding sequence for human wild-type pRb2/p130 (wtRb2), or with pcDNA3 empty vector. Three wtRb2-transfected clones (cl. 24, ci. 49, cl. 100) and one empty vector-transfected clone (cl. mock) were randomly picked and further analysed. Western blot analysis revealed high levels of pRb2/p130 in the three clones compared to mock cells. Levels of p185HER2 and the extent of its tyrosine phosphorylation were similar in all transfectant clones, as were levels of pRb1 and p107. In anchorage-independent growth assays, the number of colonies from wtRb2 clone-transfectants was about 90% less than that arising from mock cells (P<0.001). Tumor take rates of the three wtRb2-transfected clones xenografted in nu/nu mice were much lower than those of mock cells, and tumor volume was decreased by 80% (P<0.001). A mutant version of pRb2/p130 deleted of the pocket region (mut-Rb2) was also transfected into SKOV3 cells and studied in parallel with the wtRb2-transfected and pcDNA empty vector-transfected bulk populations. mut-Rb2 transfected cells showed no inhibition of in vitro colony formation and were fully tumorigenic. Together, these findings indicate that Rb2 acts as a tumor suppressor gene in vivo and in vitro in SKOV3 cells and that the intact pocket region is required for the suppressor activity.
Sujet(s)
Tumeurs de l'ovaire/anatomopathologie , Phosphoprotéines/biosynthèse , Protéines , Récepteur ErbB-2/métabolisme , Animaux , Femelle , Expression des gènes , Humains , Souris , Souris nude , Mutagenèse , Transplantation tumorale , Phosphoprotéines/génétique , Protéine p130 de type rétinoblastome , Transfection , Cellules cancéreuses en cultureRÉSUMÉ
c-erbB-2, a member of the tyrosine kinase oncogene family, is overexpressed in about 30% of human breast tumors where it correlates with poor prognosis. In vitro studies have suggested that increased expression of the receptor plays an important role in malignant progression. To better understand the direct effects of p185HER2 overexpression, a human c-erbB-2 expression vector was transfected into the hormone-dependent MCF-7 human breast carcinoma cell line and cell growth was analysed. Unexpectedly, colony formation assay revealed a reduction in the number and size of colonies as compared with mock-transfected cells. In hormone-deprived medium, c-erbB-2 transfected cells acquired growth capability, consistent with previous reports. By contrast, two c-erbB-2-transfected clones grown in complete medium showed a reduced proliferation rate despite the activation of a fully functional oncoprotein capable of autophosphorylation and induction of the MAPK pathway. The number of c-erbB-2-overexpressing cells in the S phase of the cell cycle was about one-half the number of control and mock-transfected cells. Also, overexpression of c-erbB-2 induced overexpression of p21WAF1, pRB hypophosphorylation and a mature differentiated cell phenotype with production of lipid droplets. Functional inactivation of p185HER2 by means of a specific single chain antibody indicated the c-erbB-2-dependence of the observed alterations. These data show that the exogenous overexpression of the c-erbB-2 gene in hormone-dependent breast cancer cells inhibits proliferation and induces differentiation.
Sujet(s)
Tumeurs du sein/génétique , Régulation de l'expression des gènes tumoraux , Récepteur ErbB-2/biosynthèse , Adénocarcinome/génétique , Adénocarcinome/métabolisme , Tumeurs du sein/métabolisme , Calcium-Calmodulin-Dependent Protein Kinases/métabolisme , Différenciation cellulaire , Division cellulaire , Inhibiteur p21 de kinase cycline-dépendante , Cyclines/métabolisme , Régulation négative , Activation enzymatique , Oestradiol/pharmacologie , Oestrogènes/pharmacologie , Femelle , Expression des gènes , Humains , Phénotype , Phosphorylation , Récepteur ErbB-2/génétique , Protéine du rétinoblastome/métabolisme , Transduction du signal , Cellules cancéreuses en culture , Régulation positiveRÉSUMÉ
The results of a research in progress at the Istituto di Fisica Generale Applicata--University of Milan--on natural and anthropogenic elements' determination in mosses as biological indicators are shown. The analytical technique was the energy dispersive X-ray fluorescence (EDXRF) spectrometry. The chosen areas for a preliminary pollution mapping were Italian Central Alps (Valmalenco and Valtellina) and the hills around Como (pre-Alps); in addition, a group of mosses was from Monza Park, near Milan.
Sujet(s)
Polluants atmosphériques/analyse , Surveillance de l'environnement/instrumentation , Italie , Plantes/composition chimique , Spectrométrie d'émission XRÉSUMÉ
The results are reported of an investigation carried out from 1988 to 1990 in many houses in various sites in Lombardy and Piedmont. Measurements were actually carried out in Valtellina, in Angera--on the Lombard side of lake Maggiore--and in the high valley of the river Cervo, north of Biella. The patterns of radon immission in houses due to buildings materials and also to soil emissions are described. Average values of radon levels were obtained using track-etch detectors, whereas fluctuations were recorded daily with a unit capable of detecting alpha particles in real time. Some of the values obtained in 28 Valtellina towns were quite high--e.g., about 1,000 Bq/m3 in towns along the Insubrica fault. The area around Bormio and the Masino valley did not exhibit high radioactivity levels. A total number of nearly 100 houses were investigated in Angera; the highest radon concentrations were observed in cellars and especially in the areas where fractures are bigger and more diffuse. One particular house was accurately examined with real-time analysis of radon fluctuations. Four small towns in the pluton area were investigated in the valley of the river Cervo. In this instance, values were generally high (mean concentration: 842 Bq/m3); the highest concentrations were found in cellars and in ground-floor rooms.