RÉSUMÉ
Aluminum hydride (AlH3) has attracted much attention due to its potential to replace aluminum (Al) as a novel energetic material in solid propellants. In this research, ammonium perchlorate (AP) and perfluoropolyether (PFPE) as functionalized coatings and a combination of acoustic resonance and spray drying technology have been employed to prepare AlH3@Al@AP (AHAPs) and AlH3@Al@AP@PFPE (AHAPs-F) energetic composite particles. The formulations of composite propellants and modified AlH3 particles were designed and fabricated. Their thermal reactivity, reaction heat, density, vacuum stability, combustion performance, and condensed combustion products (CCPs) have been systematically investigated. The results show that the solid propellants containing AHAPs (SP13) and AHAPs-F (SP14) composites can significantly enhance the reactivity and energy output compared to conventional solid propellants with the mechanical mixture Al/AlH3 (SP12). In particular, the total heat releases of SP13 and SP14 are almost 1.2 and 1.7 times higher than those of conventional ones (SP12, 1442 J g-1), respectively. Among the AlH3-based propellants, SP14 propellants exhibit the highest reaction heat of 5887 J g-1, the most intensive flame radiation of 31.4 × 103, and the highest combustion wave temperature of 2495 °C. Moreover, the particle size distribution of CCPs from SP14 propellants is much narrower and smaller than that of SP12, resulting in higher combustion efficiency.
RÉSUMÉ
Aluminum hydride (AlH3) is a promising fuel component of solid propellant, but its stabilization is still challenging. Herein, surface functionalization of hydrophobic perfluoropolyether (PFPE) followed by ammonium perchlorate (AP) coating has been implemented. In particular, AlH3@PFPE@xAP (x = 10, 30, 50, or 64.21%) composites (AHFPs) were prepared by a spray-drying technique. The PFPE-functionalized AlH3 with a hydrophobic surface shows an increased water contact angle (WCA) from 51.87° to 113.54°. Compared with pure AlH3, the initial decomposition temperatures of AHFPs were increased by 17 °C, and the decomposition properties of AP in the AHFPs were also enhanced with significantly decreased peak temperature and fairly increased energy output. Moreover, the decomposition induction time of AHFPs-30% was improved by almost 1.82 times that of raw AlH3, which indicates that the coatings of PFPE and AP could improve the stability of AlH3. The maximum flame radiation intensity of AHFPs-30% was 21.6 × 103, which is almost 7.71 times that of pure AlH3 (2.8 × 103).
RÉSUMÉ
The project involves determination of the activation energies and physical models for thermolysis of BCHMX and its PBXs. The initial decomposition pathways were also proposed on the basis of molecular dynamic simulation. The goal is to find the mutual relationships among the physical models, decomposition pathways, and the impact sensitivities for BCHMX and its PBXs. It has been shown that the physical model of the first step of BCHMX thermolysis is close to first order and the second step is governed by a first order autocatalytic model, which turns to "2D or 3D Nucleation and Growth" models under the effect of polymeric binders probably due to their hindrances on topochemical reaction of BCHMX. Simulation results show that the scission of N-NO2 is the initial step for BCHMX pyrolysis, followed by HONO and HNO eliminations, where the latter is due to nitro-nitrite rearrangement. Under the effect of hydrocarbon polymers, the HONO/HON elimination and collapse of ring structure of BCHMX occur earlier without changing the time for N-NO2 scission, which might be the reason why those polymers have little effect on the thermal stability of BCHMX, while they could make it decompose almost in a single complex step.