Rechargeable Li/Cl2 Battery Down to -80 °C.

Low temperature rechargeable batteries are important to life in cold climates, polar/deep-sea expeditions, and space explorations. Here, this work reports 3.5-4 V rechargeable lithium/chlorine (Li/Cl2 ) batteries operating down to -80 °C, employing Li metal negative electrode, a novel carbon dioxide (CO2 ) activated porous carbon (KJCO2 ) as the positive electrode, and a high ionic conductivity (≈5-20 mS cm-1 from -80 °C to room-temperature) electrolyte comprised of aluminum chloride (AlCl3 ), lithium chloride (LiCl), and lithium bis(fluorosulfonyl)imide (LiFSI) in low-melting-point (-104.5 °C) thionyl chloride (SOCl2 ). Between room-temperature and -80 °C, the Li/Cl2 battery delivers up to ≈29 100-4500 mAh g-1 first discharge capacity (based on carbon mass) and a 1200-5000 mAh g-1 reversible capacity over up to 130 charge-discharge cycles. Mass spectrometry and X-ray photoelectron spectroscopy probe Cl2 trapped in the porous carbon upon LiCl electro-oxidation during charging. At -80 °C, Cl2 /SCl2 /S2 Cl2 generated by electro-oxidation in the charging step are trapped in porous KJCO2 carbon, allowing for reversible reduction to afford a high discharge voltage plateau near ≈4 V with up to ≈1000 mAh g-1 capacity for SCl2 /S2 Cl2 reduction and up to ≈4000 mAh g-1 capacity at ≈3.1 V plateau for Cl2 reduction.

Shedding light on rechargeable Na/Cl2 battery.

Advancing new ideas of rechargeable batteries represents an important path to meeting the ever-increasing energy storage needs. Recently, we showed rechargeable sodium/chlorine (Na/Cl2) (or lithium/chlorine Li/Cl2) batteries that used a Na (or Li) metal negative electrode, a microporous amorphous carbon nanosphere (aCNS) positive electrode, and an electrolyte containing dissolved aluminum chloride and fluoride additives in thionyl chloride [G. Zhu et al., Nature 596, 525-530 (2021) and G. Zhu et al., J. Am. Chem. Soc. 144, 22505-22513 (2022)]. The main battery redox reaction involved conversion between NaCl and Cl2 trapped in the carbon positive electrode, delivering a cyclable capacity of up to 1,200 mAh g-1 (based on positive electrode mass) at a ~3.5 V discharge voltage [G. Zhu et al., Nature 596, 525-530 (2021) and G. Zhu et al., J. Am. Chem. Soc. 144, 22505-22513 (2022)]. Here, we identified by X-ray photoelectron spectroscopy (XPS) that upon charging a Na/Cl2 battery, chlorination of carbon in the positive electrode occurred to form carbon-chlorine (C-Cl) accompanied by molecular Cl2 infiltrating the porous aCNS, consistent with Cl2 probed by mass spectrometry. Synchrotron X-ray diffraction observed the development of graphitic ordering in the initially amorphous aCNS under battery charging when the carbon matrix was oxidized/chlorinated and infiltrated with Cl2. The C-Cl, Cl2 species and graphitic ordering were reversible upon discharge, accompanied by NaCl formation. The results revealed redox conversion between NaCl and Cl2, reversible graphitic ordering/amorphourization of carbon through battery charge/discharge, and probed trapped Cl2 in porous carbon by XPS.

Shortwave-infrared-light-emitting probes for the in vivo tracking of cancer vaccines and the elicited immune responses.

Tracking and imaging immune cells in vivo non-invasively would offer insights into the immune responses induced by vaccination. Here we report a cancer vaccine consisting of polymer-coated NaErF4/NaYF4 core-shell down-conversion nanoparticles emitting luminescence in the near-infrared spectral window IIb (1,500-1,700 nm in wavelength) and with surface-conjugated antigen (ovalbumin) and electrostatically complexed adjuvant (class-B cytosine-phosphate-guanine). Whole-body wide-field imaging of the subcutaneously injected vaccine in tumour-bearing mice revealed rapid migration of the nanoparticles to lymph nodes through lymphatic vessels, with two doses of the vaccine leading to the complete eradication of pre-existing tumours and to the prophylactic inhibition of tumour growth. The abundance of antigen-specific CD8+ T lymphocytes in the tumour microenvironment correlated with vaccine efficacy, as we show via continuous-wave imaging and lifetime imaging of two intravenously injected near-infrared-emitting probes (CD8+-T-cell-targeted NaYbF4/NaYF4 nanoparticles and H-2Kb/ovalbumin257-264 tetramer/PbS/CdS quantum dots) excited at different wavelengths, and by volumetrically visualizing the three nanoparticles via light-sheet microscopy with structured illumination. Nanoparticle-based vaccines and imaging probes emitting infrared light may facilitate the design and optimization of immunotherapies.

High-Capacity Rechargeable Li/Cl2 Batteries with Graphite Positive Electrodes.

Developing new types of high-capacity and high-energy density rechargeable batteries is important to future generations of consumer electronics, electric vehicles, and mass energy storage applications. Recently, we reported ∼3.5 V sodium/chlorine (Na/Cl2) and lithium/chlorine (Li/Cl2) batteries with up to 1200 mAh g-1 reversible capacity, using either a Na or a Li metal as the negative electrode, an amorphous carbon nanosphere (aCNS) as the positive electrode, and aluminum chloride (AlCl3) dissolved in thionyl chloride (SOCl2) with fluoride-based additives as the electrolyte [Zhu et al., Nature, 2021, 596 (7873), 525-530]. The high surface area and large pore volume of aCNS in the positive electrode facilitated NaCl or LiCl deposition and trapping of Cl2 for reversible NaCl/Cl2 or LiCl/Cl2 redox reactions and battery discharge/charge cycling. Here, we report an initially low surface area/porosity graphite (DGr) material as the positive electrode in a Li/Cl2 battery, attaining high battery performance after activation in carbon dioxide (CO2) at 1000 °C (DGr_ac) with the first discharge capacity ∼1910 mAh g-1 and a cycling capacity up to 1200 mAh g-1. Ex situ Raman spectroscopy and X-ray diffraction (XRD) revealed the evolution of graphite over battery cycling, including intercalation/deintercalation and exfoliation that generated sufficient pores for hosting LiCl/Cl2 redox. This work opens up widely available, low-cost graphitic materials for high-capacity alkali metal/Cl2 batteries. Lastly, we employed mass spectrometry to probe the Cl2 trapped in the graphitic positive electrode, shedding light into the Li/Cl2 battery operation.

A Nonflammable High-Voltage 4.7 V Anode-Free Lithium Battery.

Anode-free lithium-metal batteries employ in situ lithium-plated current collectors as negative electrodes to afford optimal mass and volumetric energy densities. The main challenges to such batteries include their poor cycling stability and the safety issues of the flammable organic electrolytes. Here, a high-voltage 4.7 V anode-free lithium-metal battery is reported, which uses a Cu foil coated with a layer (≈950 nm) of silicon-polyacrylonitrile (Si-PAN, 25.5 µg cm-2 ) as the negative electrode, a high-voltage cobalt-free LiNi0.5 Mn1.5 O4 (LNMO) as the positive electrode and a safe, nonflammable ionic liquid electrolyte composed of 4.5 m lithium bis(fluorosulfonyl)imide (LiFSI) salt in N-methyl-N-propyl pyrrolidiniumbis(fluorosulfonyl)imide (Py13 FSI) with 1 wt% lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) as additive. The Si-PAN coating is found to seed the growth of lithium during charging, and reversibly expand/shrink during lithium plating/stripping over battery cycling. The wide-voltage-window electrolyte containing a high concentration of FSI- and TFSI- facilitates the formation of stable solid-electrolyte interphase, affording a 4.7 V anode-free Cu@Si-PAN/LiNi0.5 Mn1.5 O4 battery with a reversible specific capacity of ≈120 mAh g-1 and high cycling stability (80% capacity retention after 120 cycles). These results represent the first anode-free Li battery with a high 4.7 V discharge voltage and high safety.

High-precision tumor resection down to few-cell level guided by NIR-IIb molecular fluorescence imaging.

In vivo fluorescence/luminescence imaging in the near-infrared-IIb (NIR-IIb, 1,500 to 1,700 nm) window under <1,000 nm excitation can afford subcentimeter imaging depth without any tissue autofluorescence, promising high-precision intraoperative navigation in the clinic. Here, we developed a compact imager for concurrent visible photographic and NIR-II (1,000 to 3,000 nm) fluorescence imaging for preclinical image-guided surgery. Biocompatible erbium-based rare-earth nanoparticles (ErNPs) with bright down-conversion luminescence in the NIR-IIb window were conjugated to TRC105 antibody for molecular imaging of CD105 angiogenesis markers in 4T1 murine breast tumors. Under a ∼940 ± 38 nm light-emitting diode (LED) excitation, NIR-IIb imaging of 1,500- to 1,700-nm emission afforded noninvasive tumor­to­normal tissue (T/NT) signal ratios of ∼40 before surgery and an ultrahigh intraoperative tumor-to-muscle (T/M) ratio of ∼300, resolving tumor margin unambiguously without interfering background signal from surrounding healthy tissues. High-resolution imaging resolved small numbers of residual cancer cells during surgery, allowing thorough and nonexcessive tumor removal at the few-cell level. NIR-IIb molecular imaging afforded 10-times-higher and 100-times-higher T/NT and T/M ratios, respectively, than imaging with IRDye800CW-TRC105 in the ∼900- to 1,300-nm range. The vastly improved resolution of tumor margin and diminished background open a paradigm of molecular imaging-guided surgery.

Rechargeable Na/Cl2 and Li/Cl2 batteries.

Lithium-ion batteries (LIBs) are widely used in applications ranging from electric vehicles to wearable devices. Before the invention of secondary LIBs, the primary lithium-thionyl chloride (Li-SOCl2) battery was developed in the 1970s using SOCl2 as the catholyte, lithium metal as the anode and amorphous carbon as the cathode1-7. This battery discharges by lithium oxidation and catholyte reduction to sulfur, sulfur dioxide and lithium chloride, is well known for its high energy density and is widely used in real-world applications; however, it has not been made rechargeable since its invention8-13. Here we show that with a highly microporous carbon positive electrode, a starting electrolyte composed of aluminium chloride in SOCl2 with fluoride-based additives, and either sodium or lithium as the negative electrode, we can produce a rechargeable Na/Cl2 or Li/Cl2 battery operating via redox between mainly Cl2/Cl- in the micropores of carbon and Na/Na+ or Li/Li+ redox on the sodium or lithium metal. The reversible Cl2/NaCl or Cl2/LiCl redox in the microporous carbon affords rechargeability at the positive electrode side and the thin alkali-fluoride-doped alkali-chloride solid electrolyte interface stabilizes the negative electrode, both are critical to secondary alkali-metal/Cl2 batteries.

Selective and High Current CO2 Electro-Reduction to Multicarbon Products in Near-Neutral KCl Electrolytes.

Reducing CO2 to value-added multicarbon (C2+) fuels and chemicals using renewable energy is a viable way to circumvent CO2 buildup in the atmosphere and facilitate closing the carbon cycle. To date it remains a challenge to achieve high product selectivity and long-term stability of electrocatalytic carbon dioxide reduction reaction (CO2RR) especially at practically relevant high current levels >100 mA cm-2. Here, we report a simple electrodeposited Cu electrocatalyst on a hydrophobic porous gas-diffusion layer (GDL) electrode affording stable and selective CO2RR to C2+ products in near-neutral KCl electrolytes. By directing the CO2 stream to fully submerged hydrophobic GDLs in a H-cell, high C2+ partial current densities near 100 mA cm-2 were achieved. In a flow-cell setup, the Cu/GDL cathode in 2 M KCl afforded stable CO2RR superior to that in widely used KOH electrolytes. We found that Cu etching/corrosion associated with trace oxygen played a role in the catalyst instability in alkaline media under cathodic CO2RR conditions, a problem largely suppressed in near-neutral electrolyte. A two-electrode CO2 electrolyzer was constructed with a Cu/GDL cathode in KCl catholyte and an anode comprised of nickel-iron hydroxide on nickel foam (NiFe/NF) in a KOH anolyte separated by Nafion membrane. By periodically adding HCl to the KCl catholyte to compensate the increasing pH and remove accumulated (bi)carbonates, we observed little decay over ∼30 h in flow-cell CO2RR activity and selectivity at 150 mA cm-2 with a high Faradaic efficiency (FE) of ∼75% and energy efficiency of 40% for C2+ products.

A high-performance potassium metal battery using safe ionic liquid electrolyte.

Potassium secondary batteries are contenders of next-generation energy storage devices owing to the much higher abundance of potassium than lithium. However, safety issues and poor cycle life of K metal battery have been key bottlenecks. Here we report an ionic liquid electrolyte comprising 1-ethyl-3-methylimidazolium chloride/AlCl3/KCl/potassium bis(fluorosulfonyl) imide for safe and high-performance batteries. The electrolyte is nonflammable and exhibits a high ionic conductivity of 13.1 mS cm-1 at room temperature. A 3.6-V battery with K anode and Prussian blue/reduced graphene oxide cathode delivers a high energy and power density of 381 and 1,350 W kg-1, respectively. The battery shows an excellent cycling stability over 820 cycles, retaining ∼89% of the original capacity with high Coulombic efficiencies of ∼99.9%. High cyclability is also achieved at elevated temperatures up to 60 °C. Uniquely, robust K, Al, F, and Cl-containing passivating interphases are afforded with this electrolyte, which is key to superior battery cycling performances.

High-Safety and High-Energy-Density Lithium Metal Batteries in a Novel Ionic-Liquid Electrolyte.

Rechargeable lithium metal batteries are next generation energy storage devices with high energy density, but face challenges in achieving high energy density, high safety, and long cycle life. Here, lithium metal batteries in a novel nonflammable ionic-liquid (IL) electrolyte composed of 1-ethyl-3-methylimidazolium (EMIm) cations and high-concentration bis(fluorosulfonyl)imide (FSI) anions, with sodium bis(trifluoromethanesulfonyl)imide (NaTFSI) as a key additive are reported. The Na ion participates in the formation of hybrid passivation interphases and contributes to dendrite-free Li deposition and reversible cathode electrochemistry. The electrolyte of low viscosity allows practically useful cathode mass loading up to ≈16 mg cm-2 . Li anodes paired with lithium cobalt oxide (LiCoO2 ) and lithium nickel cobalt manganese oxide (LiNi0.8 Co0.1 Mn0.1 O2 , NCM 811) cathodes exhibit 99.6-99.9% Coulombic efficiencies, high discharge voltages up to 4.4 V, high specific capacity and energy density up to ≈199 mAh g-1 and ≈765 Wh kg-1 respectively, with impressive cycling performances over up to 1200 cycles. Highly stable passivation interphases formed on both electrodes in the novel IL electrolyte are the key to highly reversible lithium metal batteries, especially for Li-NMC 811 full batteries.

Electroreduction of CO2 to Formate on a Copper-Based Electrocatalyst at High Pressures with High Energy Conversion Efficiency.

Electrocatalytic CO2 reduction (CO2RR) to valuable fuels is a promising approach to mitigate energy and environmental problems, but controlling the reaction pathways and products remains challenging. Here a novel Cu2O nanoparticle film was synthesized by square-wave (SW) electrochemical redox cycling of high-purity Cu foils. The cathode afforded up to 98% Faradaic efficiency for electroreduction of CO2 to nearly pure formate under ≥45 atm CO2 in bicarbonate catholytes. When this cathode was paired with a newly developed NiFe hydroxide carbonate anode in KOH/borate anolyte, the resulting two-electrode high-pressure electrolysis cell achieved high energy conversion efficiencies of up to 55.8% stably for long-term formate production. While the high-pressure conditions drastically increased the solubility of CO2 to enhance CO2 reduction and suppress hydrogen evolution, the (111)-oriented Cu2O film was found to be important to afford nearly 100% CO2 reduction to formate. The results have implications for CO2 reduction to a single liquid product with high energy conversion efficiency.

A safe and non-flammable sodium metal battery based on an ionic liquid electrolyte.

Rechargeable sodium metal batteries with high energy density could be important to a wide range of energy applications in modern society. The pursuit of higher energy density should ideally come with high safety, a goal difficult for electrolytes based on organic solvents. Here we report a chloroaluminate ionic liquid electrolyte comprised of aluminium chloride/1-methyl-3-ethylimidazolium chloride/sodium chloride ionic liquid spiked with two important additives, ethylaluminum dichloride and 1-ethyl-3-methylimidazolium bis(fluorosulfonyl)imide. This leads to the first chloroaluminate based ionic liquid electrolyte for rechargeable sodium metal battery. The obtained batteries reached voltages up to ~ 4 V, high Coulombic efficiency up to 99.9%, and high energy and power density of ~ 420 Wh kg-1 and ~ 1766 W kg-1, respectively. The batteries retained over 90% of the original capacity after 700 cycles, suggesting an effective approach to sodium metal batteries with high energy/high power density, long cycle life and high safety.

Rechargeable aluminum batteries: effects of cations in ionic liquid electrolytes.

Room temperature ionic liquids (RTILs) are solvent-free liquids comprised of densely packed cations and anions. The low vapor pressure and low flammability make ILs interesting for electrolytes in batteries. In this work, a new class of ionic liquids were formed for rechargeable aluminum/graphite battery electrolytes by mixing 1-methyl-1-propylpyrrolidinium chloride (Py13Cl) with various ratios of aluminum chloride (AlCl3) (AlCl3/Py13Cl molar ratio = 1.4 to 1.7). Fundamental properties of the ionic liquids, including density, viscosity, conductivity, anion concentrations and electrolyte ion percent were investigated and compared with the previously investigated 1-ethyl-3-methylimidazolium chloride (EMIC-AlCl3) ionic liquids. The results showed that the Py13Cl-AlCl3 ionic liquid exhibited lower density, higher viscosity and lower conductivity than its EMIC-AlCl3 counterpart. We devised a Raman scattering spectroscopy method probing ILs over a Si substrate, and by using the Si Raman scattering peak for normalization, we quantified speciation including AlCl4 -, Al2Cl7 -, and larger AlCl3 related species with the general formula (AlCl3) n in different IL electrolytes. We found that larger (AlCl3) n species existed only in the Py13Cl-AlCl3 system. We propose that the larger cationic size of Py13+ (142 Å3) versus EMI+ (118 Å3) dictated the differences in the chemical and physical properties of the two ionic liquids. Both ionic liquids were used as electrolytes for aluminum-graphite batteries, with the performances of batteries compared. The chloroaluminate anion-graphite charging capacity and cycling stability of the two batteries were similar. The Py13Cl-AlCl3 based battery showed a slightly larger overpotential than EMIC-AlCl3, leading to lower energy efficiency resulting from higher viscosity and lower conductivity. The results here provide fundamental insights into ionic liquid electrolyte design for optimal battery performance.

An operando X-ray diffraction study of chloroaluminate anion-graphite intercalation in aluminum batteries.

We investigated rechargeable aluminum (Al) batteries composed of an Al negative electrode, a graphite positive electrode, and an ionic liquid (IL) electrolyte at temperatures down to -40 °C. The reversible battery discharge capacity at low temperatures could be superior to that at room temperature. In situ/operando electrochemical and synchrotron X-ray diffraction experiments combined with theoretical modeling revealed stable AlCl4-/graphite intercalation up to stage 3 at low temperatures, whereas intercalation was reversible up to stage 4 at room temperature (RT). The higher-degree anion/graphite intercalation at low temperatures affords rechargeable Al battery with higher discharge voltage (up to 2.5 V, a record for Al battery) and energy density. A remarkable cycle life of >20,000 cycles at a rate of 6C (10 minutes charge time) was achievable for Al battery operating at low temperatures, corresponding to a >50-year battery life if charged/discharged once daily.

3D Freeze-Casting of Cellular Graphene Films for Ultrahigh-Power-Density Supercapacitors.

3D cellular graphene films with open porosity, high electrical conductivity, and good tensile strength, can be synthesized by a method combining freeze-casting and filtration. The resulting supercapacitors based on 3D porous reduced graphene oxide (RGO) film exhibit extremely high specific power densities and high energy densities. The fabrication process provides an effective means for controlling the pore size, electronic conductivity, and loading mass of the electrode materials, toward devices with high energy-storage performance.