Exploration of occurrence and sources of microplastics (>10 µm) in Danish marine waters.

Microplastics (MPs) were quantified in Danish marine waters of the Kattegat and the southernmost part of Skagerrak bordering to it. Kattegat is a waterbody between Denmark and Sweden that receives inflow from the Baltic Sea and direct urban runoff from the metropolitan area of Copenhagen and Malmö. MPs were measured in 14 continuous transects while steaming between monitoring stations. MP levels tended to be highest close to the Copenhagen-Malmö area, albeit this was more obvious from the abundance of particles rather than mass. The outcome of the measurements allowed a rough MP budget in the Danish Straits region, suggesting that urban waste- and stormwater discharges could not be neglected as potential MP source in these waters. The marine samples were collected by pumping and filtering water over 10 µm steel filters, hereby sampling a total of 19.3 m3. They were prepared and analyzed by FPA-µFTIR imaging, and the scans interpreted to yield MP size, shape, polymer type, and estimated mass. The average concentration was 103 ± 86 items m-3, corresponding to 23.3 ± 28.3 µg m-3 (17-286 items m-3; 0.6-84.1 µg m-3). Most MPs were smaller than 100 µm and fragments dominated the samples. The carbonyl index was assessed for polyolefins, showing that oxidation increased with decreasing MP size, but did not correlate with distance to urban areas. A rough budget of MP in the Danish Straits region suggested that MPs discharged from urban waste- and stormwaters were an import source of MPs.

Anthropogenically impacted lake catchments in Denmark reveal low microplastic pollution.

Microplastics have been detected in lake environments globally, including in remote regions. Agricultural and populated areas are known to congregate several inputs and release pathways for microplastic. This study investigated microplastic (50-5000 µm) contamination in five Danish freshwater lakes with catchments dominated by arable land use. The concentrations in sediments (n = 3/site) and the zebra mussel, Dreissena polymorpha (n = 30/site), were calculated and compared with catchment characteristics and environmental parameters. Microplastic concentrations in sediment were relatively low (average 0.028 ± 0.017 items/g dry weight sediment) whilst only a single microplastic was found in the mussels (average 0.067 ± 0.249 items/10 individual). Hence, no relationship between the number of observed microplastics in sediment and mussels could be identified, nor could a relationship between concentration in sediment and environmental parameters. As all lakes studied received their water from moderate to heavily anthropogenically impacted catchments, it was expected that they would be sinks for microplastic with high bioavailability. Based on the results of the present study, D. polymorpha were found to not be contaminated by microplastics in the five study lakes. Thus, our results suggest that these mussels do not interact with microplastics at low concentrations. We speculate that the results on sediment and biota could be explained by several factors related to regional differences in plastic use, species characteristics, sampling size, and the fact that finding no microplastic is not always reported in the scientific literature. Thus, the paper provides insight into the dynamics between the catchment, lake, and biota in systems with low microplastic concentration.

Microplastics in the high-altitude Himalayas: Assessment of microplastic contamination in freshwater lake sediments, Northwest Himalaya (India).

In this study, we assess the magnitude, type, and sources of microplastic (MP) in lake bottom sediments collected from freshwater Anchar Lake, located in the Kashmir Valley, Northwest Himalaya. The MP identification was done on twenty-four lake bottom sediment samples under a stereo-microscope, and their polymer compositions were characterized using an Attenuated Total Reflectance Fourier Transform Infrared (ATR-FTIR) spectroscopy. The study reveals that 606 ± 360 (average ± SD, n = 24) numbers of MP were present per kilogram of dry sediment samples, with fibers (91%), fragments/films (8%), and pellets (1%) dominating the shape groups. Polyamide (PA, 96%) was the dominant polymer composition present in the sediment samples, followed by polyethylene terephthalate (PET, 1.4%), polystyrene (PS, 1.4%), polyvinyl chloride (PVC, 0.9%), and polypropylene (PP, 0.7%). Polymer Hazard Index (PHI) and Pollution Load Index (PLI) were used to evaluate the quality of sediments. It was noted that high PHI values (>1000) were due to the presence of PVC polymer. According to PLI values, sediments in the Anchar lake are less contaminated with MP. We conclude that MP in the Anchar Lake have a complex source derived mostly from the automobile, textile, and packaging industries.

Occurrence and distribution of microplastics in domestic, industrial, agricultural and aquacultural wastewater sources: A case study in Changzhou, China.

The extensive application of plastic in human life brings about microplastic (MP) pollution in the environment. Identifying the potential sources of MPs is necessary to diminish its pollution. In this study, the occurrence, composition and distribution of MPs in the influents and effluents from 9 domestic wastewater treatment plants (WWTPs), 5 industrial WWTPs, wastewater of 10 industrial plants, 4 livestock farms and 4 fish ponds in China were investigated. Water samples were enzymatically treated followed by digestion with hydrogen peroxide and density separation. MPs were characterized using micro-Raman spectroscopy and were categorized by shape, size and color. Results showed that MP abundance in the influents and effluents of domestic WWTPs was 18-890 and 6-26 n·L-1, respectively, with the removal efficiency ranging from 35 to 98%. The effluents of industrial WWTPs contained 6-12 n·L-1 and the levels of MPs in the wastewater of industrial plants, livestock farms and fish ponds were in the range of 8-23, 8-40 and 13-27 n·L-1, respectively. No significant differences of MP abundance were demonstrated among effluents or wastewater of different sources, indicating they all constitute sources of MP pollution. Polyethylene (PE), polypropylene (PP) and polystyrene (PS) made up almost 83% of the total MPs. Fragment and film were the most abundant shapes and the majority of MPs were smaller than 500 µm. Polymer type and shape in different sources did not vary statistically, however, there were slight differences among different sources concerning size and color of MPs. This study could fill MP data gaps regarding different sources, guide future monitoring work and policy making.

Does mechanical stress cause microplastic release from plastic water bottles?

Plastic particle ingestion has become of concern as a possible threat to human health. Previous works have already explored the presence of microplastic (MP) in bottled drinking water as a source of MP intake. Here, we consider the release of MP particles from single-use PET mineral water bottles upon exposure to mechanical stress utilizing SEM plus EDS, which allows the implementation of morphological and elemental analysis of the plastic material surface and quantification of particle concentrations in sample water. The aim of this study was to better evaluate the sources of MP intake from plastic bottles, especially considering the effect of daily use on these bottles such as the abrasion of the plastic material. For that, we analysed MP release of PET bottlenecks and HDPE caps on their surfaces after a series of bottle openings/closings (1 x, 10 x, 100 x). Furthermore, we investigated, if the inner surface of the PET bottles released MPs, counted particle increase of the water and identified MPs in the PET bottled water after exposing the bottles to mechanical stress (squeezing treatment; none, 1 min, 10 min). The results showed a considerable increase of MP particle occurrence on the surface of PET and HDPE material (bottlenecks and caps) after opening and closing the bottles. After 100 times the effect was impressive, especially on caps. Moreover, great differences exist in cap abrasion between brands which uncovers a discrepancy in plastic behavior of brands. Interestingly, particle concentrations in the bottled mineral water did not significantly increase after exposure to mechanical stress (squeezing treatment). The morphological analysis of the inner wall surface of the bottles supported this observation, as no stress cracks could be detected after the treatment, implying that the bottles itself are not a consistent source of MP particles after this extent of mechanical stress. However, chances of MP ingestion by humans increase with frequent use of the same single-use plastic bottle, though only from the bottleneck-cap system.

Synthetic fibers in atmospheric fallout: A source of microplastics in the environment?

Sources, pathways and reservoirs of microplastics, plastic particles smaller than 5mm, remain poorly documented in an urban context. While some studies pointed out wastewater treatment plants as a potential pathway of microplastics, none have focused on the atmospheric compartment. In this work, the atmospheric fallout of microplastics was investigated in two different urban and sub-urban sites. Microplastics were collected continuously with a stainless steel funnel. Samples were then filtered and observed with a stereomicroscope. Fibers accounted for almost all the microplastics collected. An atmospheric fallout between 2 and 355 particles/m(2)/day was highlighted. Registered fluxes were systematically higher at the urban than at the sub-urban site. Chemical characterization allowed to estimate at 29% the proportion of these fibers being all synthetic (made with petrochemicals), or a mixture of natural and synthetic material. Extrapolation using weight and volume estimates of the collected fibers, allowed a rough estimation showing that between 3 and 10 tons of fibers are deposited by atmospheric fallout at the scale of the Parisian agglomeration every year (2500 km(2)). These results could serve the scientific community working on the different sources of microplastic in both continental and marine environments.