Neuroprotective Effects of Zinc Oxide Nanoparticles in a Rotenone-Induced Mouse Model of Parkinson's Disease.

Goals of the investigation: This work aimed to evaluate the neuroprotective effects of zinc oxide (ZnO) nanoparticles in an experimental mouse model of rotenone-induced PD and investigate the therapeutic effects of ZnO, cobalt ferrite nanoparticles, and their combination. Methods: The levels of dopamine, norepinephrine, epinephrine, and serotonin were assessed using ELISA in the control and experimental model of PD mice. The dopa-decarboxylase expression level was assayed by real-time PCR. The expression level of tyrosine hydroxylase (TH) was assessed by western blot analysis. Results: Our data showed that levels of dopamine decreased in PD mice compared to normal. ZnO NP increased dopamine levels in normal and PD mice (37.5% and 29.5%; respectively, compared to untreated mice). However, ZnO NP did not cause any change in norepinephrine and epinephrine levels either in normal or in PD mice. Levels of serotonin decreased by 64.0%, and 51.1% in PD mice treated with cobalt ferrite and dual ZnO- cobalt ferrite NPs; respectively, when compared to PD untreated mice. The mRNA levels of dopa-decarboxylase increased in both normal and PD mice treated with ZnO NP. Its level decreased when using cobalt ferrite NP and the dual ZnO-cobalt ferrite NP when compared to untreated PD mice. A significant decrease in TH expression by 0.25, 0.68, and 0.62 folds was observed in normal mice treated with ZnO, cobalt ferrite, and the dual ZnO-cobalt ferrite NP as compared to normal untreated mice. In PD mice, ZnO administration caused a non-significant 0.15-fold decrease in TH levels while both cobalt ferrite and the dual ZnO-cobalt ferrite NP administration caused a significant 0.3 and 0.4-fold decrease respectively when compared to untreated PD mice. Principal conclusion: This study reveals that ZnO NPs may be utilized as a potential intervention to elevate dopamine levels to aid in PD treatment.

Preparation of a 3D printable high-performance GelMA hydrogel loading with magnetic cobalt ferrite nanoparticles.

Osteosarcoma remains a worldwide concern due to the poor effectiveness of available therapies in the clinic. Therefore, it is necessary to find a safe and effective therapy to realize the complete resection of osteosarcoma and reconstruction of the bone defect. Magnetic hyperthermia based on magnetic nanoparticles can kill tumor cells by raising the temperature without causing the side effects of conventional cancer treatments. This research aims to design a high-performance magnetic hydrogel composed of gelatin methacrylate and highly magnetic cobalt ferrite (CFO) nanoparticles for osteosarcoma treatment. Specifically, CFO is surface functionalized with methacrylate groups (MeCFO). The surface modified CFO has good biocompatibility and stable solution dispersion ability. Afterward, MeCFO nanoparticles are incorporated into GelMA to fabricate a three-dimensional (3D) printable MeCFO/GelMA magnetic hydrogel and then photocross-linked by UV radiation. MeCFO/GelMA hydrogel has high porosity and swelling ability, indicating that the hydrogel possesses more space and good hydrophily for cell survival. The rheological results showed that the hydrogel has shear thinning property, which is suitable as a bioprinting ink to produce desired structures by a 3D printer. Furthermore, 50 µg/mL MeCFO not only decreases the cell activity of osteosarcoma cells but also promotes the osteogenic differentiation of mBMSCs. The results of the CCK-8 assay and live/dead staining showed that MeCFO/GelMA hydrogel had good cytocompatibility. These results indicated that MeCFO/GelMA hydrogel with potential antitumor and bone reconstruction functions is a promising therapeutic strategy after osteosarcoma resection.

Cobalt Ferrite Nanoparticle's Safety in Biomedical and Agricultural Applications: A Review of Recent Progress.

Cobalt ferrite nanoparticles (CFN) have drawn attention as a theranostic agent. Unique physicochemical features of CFN and magnetic properties make CFN an outstanding candidate for biomedical, agricultural, and environmental applications. The extensive use of CFN may result in intentional inoculation of humans for disease diagnosis and therapeutic purposes or unintentional penetration of CFN via inhalation, ingestion, adsorption, or other means. Therefore, understanding the potential cytotoxicity of CFN may pave the way for their future biomedical and agricultural applications. This review scrutinized CFN biocompatibility, possible effects, and cytotoxic mechanisms in different biological systems. Literature indicates CFN toxicity is linked with their size, synthesizing methods, coating materials, exposure time, route of administration, and test concentrations. Some in vitro cytotoxicity tests showed misleading results of CFN potency; this might be due to the interaction of CFN with cytotoxicity assay regents. To date, published research indicates that the biocompatibility of CFN outweighed its cytotoxic effects in plant or animal models, but the opposite outcomes were observed in aquatic Zebrafish.

Controlled Electrophoretic Deposition Strategy of Binder-Free CoFe2O4 Nanoparticles as an Enhanced Electrocatalyst for the Oxygen Evolution Reaction.

The kinetic-sluggish oxygen evolution reaction (OER) is the main obstacle in electrocatalytic water splitting for sustainable production of hydrogen energy. Efficient water electrolysis can be ensured by lowering the overpotential of the OER by developing highly active catalysts. In this study, a controlled electrophoretic deposition strategy was used to develop a binder-free spinel oxide nanoparticle-coated Ni foam as an efficient electrocatalyst for water oxidation. Oxygen evolution was successfully promoted using the CoFe2O4 catalyst, and it was optimized by modulating the electrophoretic parameters. When optimized, CoFe2O4 nanoparticles presented more active catalytic sites, superior charge transfer, increased ion diffusion, and favorable reaction kinetics, which led to a small overpotential of 287 mV for a current density of 10 mA cm-2, with a small Tafel slope of 43 mV dec-1. Moreover, the CoFe2O4 nanoparticle electrode exhibited considerable long-term stability over 100 h without detectable activity loss. The results demonstrate promising potential for large-scale water splitting using Earth-abundant oxide materials via a simple and cheap fabrication process.

Superparamagnetic Hyperthermia Study with Cobalt Ferrite Nanoparticles Covered with γ-Cyclodextrins by Computer Simulation for Application in Alternative Cancer Therapy.

In this paper, we present a study by computer simulation on superparamagnetic hyperthermia with CoFe2O4 ferrimagnetic nanoparticles coated with biocompatible gamma-cyclodextrins (γ-CDs) to be used in alternative cancer therapy with increased efficacy and non-toxicity. The specific loss power that leads to the heating of nanoparticles in superparamagnetic hyperthermia using CoFe2O4-γ-CDs was analyzed in detail depending on the size of the nanoparticles, the thickness of the γ-CDs layer on the nanoparticle surface, the amplitude and frequency of the alternating magnetic field, and the packing fraction of nanoparticles, in order to find the proper conditions in which the specific loss power is maximal. We found that the maximum specific loss power was determined by the Brown magnetic relaxation processes, and the maximum power obtained was significantly higher than that which would be obtained by the Néel relaxation processes under the same conditions. Moreover, increasing the amplitude of the magnetic field led to a significant decrease in the optimal diameter at which the maximum specific loss power is obtained (e.g., for 500 kHz frequency the optimal diameter decreased from 13.6 nm to 9.8 nm when the field increased from 10 kA/m to 50 kA/m), constituting a major advantage in magnetic hyperthermia for its optimization, in contrast to the known results in the absence of cyclodextrins from the surface of immobilized nanoparticles of CoFe2O4, where the optimal diameter remained practically unchanged at ~6.2 nm.

In vitro characterization of hydroxyapatite and cobalt ferrite nanoparticles compounds and their biocompatibility in vivo.

Bioactive materials in combination with antibiotics have been widely developed for the treatment of bone infection. Thus, this work aims to characterize six biomaterials formulated with different concentrations of hydroxyapatite and cobalt ferrite nanoparticles, in addition to the antibiotic ciprofloxacin, using X-ray diffraction (XRD), scanning electron microscopy (SEM), and the antibiotic diffusion test on agar. Furthermore, in vivo biocompatibility and the reabsorption process of these materials were analyzed. XRD showed that both hydroxyapatite and cobalt ferrite present high crystallinity. The photomicrographs obtained by SEM revealed that composites have a complex surface, evidenced by the irregular arrangement of the hydroxyapatite and cobalt ferrite granules, besides demonstrating the interaction between their components. The antibiotic-diffusion test showed that all biomaterials produced an inhibition halo in Staphylococcus aureus cultures. For the biocompatibility study, composites were surgically implanted in the dorsal region of rabbits. At 15, 30, 70, and 100 days, biopsies of the implanted regions were performed. The biomaterials were easily identified during histological analysis and no significant inflammatory process, nor histological signs of toxicity or rejection by the adjacent tissue were observed. We can conclude that the biomaterials analyzed are biocompatible, degradable, and effective in inhibiting the in vitro growth of Staphylococcus aureus. Graphical abstract.

Comparison of copper and aluminum doped cobalt ferrate nanoparticles for improving biohydrogen production.

Two various materials, copper and aluminum doped cobalt ferrite nanoparticles (NPs) were fabricated for investigating their effects of addition amounts on hydrogen (H2) synthesis and process stability. CoCu0.2Fe1.8O4NPs enhanced H2 production more than CoAl0.2Fe1.8O4 NPs under same condition. The highest H2 yield of 212.25 ml/g glucose was found at optimal dosage of 300 mg/L CoCu0.2Fe1.8O4 NPs, revealing the increases of 43.17% and 6.67% compared with the control without NPs and 300 mg/L CoAl0.2Fe1.8O4 NPs groups, respectively. NPs level of more than 400 mg/L inhibited H2 generation. Further investigations illustrated that CoCu0.2Fe1.8O4 NPs were mainly distributed on extracellular polymer substance while CoAl0.2Fe1.8O4 NPs were mostly enriched on cell membrane, which facilitated electron transfer behavior. Community structure composition demonstrated that CoCu0.2Fe1.8O4 and CoAl0.2Fe1.8O4 separately caused a 9.67% and 9.03% increase in Clostridium sensu stricto 1 compared with the control reactor without NPs exposure.

The Influence of Zn Substitution on Physical Properties of CoFe2O4 Nanoparticles.

Co1−xZnxFe2O4 nanoparticles (0 ≤ x ≤ 1) have been synthesized via a green sol−gel combustion method. The prepared samples were studied using X-ray diffraction measurements (XRD), transmission electron microscopy (TEM), Raman, and magnetic measurements. All samples were found to be single phases and have a cubic Fd-3m structure. EDS analysis confirmed the presence of cobalt, zinc, iron, and oxygen in all studied samples. Raman spectra clearly show that Zn ions are preferentially located in T sites for low Zn concentrations. Due to their high crystallinity, the nanoparticles show high values of the magnetization, which increases with the Zn content for x < 0.5. The magnetic properties are discussed based on Raman results. Co ferrite doped with 30% of Zn produced the largest SAR values, which increase linearly from 148 to 840 W/gMNPs as the H is increased from 20 to 60 kA/m.

Effects of Process Variables on Properties of CoFe2O4 Nanoparticles Prepared by Solvothermal Process.

Controlling the morphology and magnetic properties of CoFe2O4 nanoparticles is crucial for the synthesis of compatible materials for different applications. CoFe2O4 nanoparticles were synthesized by a solvothermal method using cobalt nitrate, iron nitrate as precursors, and oleic acid as a surfactant. The formation of CoFe2O4 nanoparticles was systematically observed by adjusting synthesis process conditions including reaction temperature, reaction time, and oleic acid concentration. Nearly spherical, monodispersed CoFe2O4 nanoparticles were formed by changing the reaction time and reaction temperature. The oleic acid-coated CoFe2O4 nanoparticles inhibited the growth of particle size after 1 h and, therefore, the particle size of CoFe2O4 nanoparticles did not change significantly as the reaction time increased. Both without and with low oleic acid concentration, the large-sized cubic CoFe2O4 nanoparticles showing ferromagnetic behavior were synthesized, while the small-sized CoFe2O4 nanoparticles with superparamagnetic properties were obtained for the oleic acid concentration higher than 0.1 M. This study will become a basis for further research in the future to prepare the high-functional CoFe2O4 magnetic nanoparticles by a solvothermal process, which can be applied to bio-separation, biosensors, drug delivery, magnetic hyperthermia, etc.

Specific Absorption Rate Dependency on the Co2+ Distribution and Magnetic Properties in CoxMn1-xFe2O4 Nanoparticles.

Mixed ferrite nanoparticles with compositions CoxMn1-xFe2O4 (x = 0, 0.2, 0.4, 0.6, 0.8, and 1.0) were synthesized by a simple chemical co-precipitation method. The structure and morphology of the nanoparticles were obtained by X-ray diffraction (XRD), transmission electron microscope (TEM), Raman spectroscopy, and Mössbauer spectroscopy. The average crystallite sizes decreased with increasing x, starting with 34.9 ± 0.6 nm for MnFe2O4 (x = 0) and ending with 15.0 ± 0.3 nm for CoFe2O4 (x = 1.0). TEM images show an edge morphology with the majority of the particles having cubic geometry and wide size distributions. The mixed ferrite and CoFe2O4 nanoparticles have an inverse spinel structure indicated by the splitting of A1g peak at around 620 cm-1 in Raman spectra. The intensity ratios of the A1g(1) and A1g(2) peaks indicate significant redistribution of Co2+ and Fe3+ cations among tetrahedral and octahedral sites in the mixed ferrite nanoparticles. Magnetic hysterics loops show that all the particles possess significant remnant magnetization and coercivity at room temperature. The mass-normalized saturation magnetization is highest for the composition with x = 0.8 (67.63 emu/g), while CoFe2O4 has a value of 65.19 emu/g. The nanoparticles were PEG (poly ethylene glycol) coated and examined for the magneto thermic heating ability using alternating magnetic field. Heating profiles with frequencies of 333.45, 349.20, 390.15, 491.10, 634.45, and 765.95 kHz and 200, 250, 300, and 350 G field amplitudes were obtained. The composition with x = 0.2 (Co0.2Mn0.8Fe2O4) with saturation magnetization 57.41 emu/g shows the highest specific absorption rate (SAR) value of 190.61 W/g for 10 mg/mL water dispersions at a frequency of 765.95 kHz and 350 G field strength. The SAR values for the mixed ferrite and CoFe2O4 nanoparticles increase with increasing concentration of particle dispersions, whereas for MnFe2O4, nanoparticles decrease with increasing the concentration of particle dispersions. SARs obtained for Co0.2Mn0.8Fe2O4 and CoFe2O4 nanoparticles fixed in agar ferrogel dispersions at frequency of 765.95 kHz and 350 G field strength are 140.35 and 67.60 W/g, respectively. This study shows the importance of optimizing the occupancy of Co2+ among tetrahedral and octahedral sites of the spinel system, concentration of the magnetic nanoparticle dispersions, and viscosity of the surrounding medium on the magnetic properties and heating efficiencies.

Cobalt Ferrite Nanoparticles for Tumor Therapy: Effective Heating versus Possible Toxicity.

Magnetic nanoparticles (MNPs) are widely considered for cancer treatment, in particular for magnetic hyperthermia (MHT). Thereby, MNPs are still being optimized for lowest possible toxicity on organisms while the magnetic properties are matched for best heating capabilities. In this study, the biocompatibility of 12 nm cobalt ferrite MNPs, functionalized with citrate ions, in different dosages on mice and rats of both sexes was investigated for 30 days after intraperitoneal injection. The animals' weight, behavior, and blood cells changes, as well as blood biochemical parameters are correlated to histological examination of organs revealing that cobalt ferrite MNPs do not have toxic effects at concentrations close to those used previously for efficient MHT. Moreover, these MNPs demonstrated high specific loss power (SLP) of about 400 W g-1. Importantly the MNPs retained their magnetic properties inside tumor tissue after intratumoral administration for several MHT cycles within three days. Thus, cobalt ferrite MNPs represent a perspective platform for tumor therapy by MHT due to their ability to provide effective heating without exerting a toxic effect on the organism. This opens up new avenues for smaller MNPs sizes while their heating efficiency is maintained.

Anticancer potential of docetaxel-loaded cobalt ferrite nanocarrier: an in vitro study on MCF-7 and MDA-MB-231 cell lines.

AIM: To develop a biocompatible cobalt ferrite (CF-NP) nanodrug formulation using oleic acid and poly (d,l-lactide-co-glycolic) acid (PLGA) for the delivery of docetaxel (DTX) specifically to breast cancer cells. METHODS: The CF-NP were synthesised by hydrothermal method and conjugated with DTX in a PLGA matrix and were systematically characterised using XRD, FE-SEM, TEM, DLS, FTIR, TGA, SQUID etc. The drug loading, in vitro drug release, cellular uptake, cytotoxicity were evaluated and haemolytic effect was studied. RESULTS: The CF-NP showed good crystallinity with an average particle size of 21 nm and ferromagnetic nature. The DTX-loaded CF-NP (DCF-NP) showed 8.4% (w/w) drug loading with 81.8% loading efficiency with a sustained DTX release over time. An effective internalisation and anti-proliferative efficiency was observed in MCF-7 and MDA-MB-231 breast cancer cells and negligible haemolytic effect. CONCLUSION: The DCF-NP can have the potential for the effective delivery of DTX for breast cancer treatment.

Exploiting Unique Alignment of Cobalt Ferrite Nanoparticles, Mild Hyperthermia, and Controlled Intrinsic Cobalt Toxicity for Cancer Therapy.

Nanoparticle-based magnetic hyperthermia is a well-known thermal therapy platform studied to treat solid tumors, but its use for monotherapy is limited due to incomplete tumor eradication at hyperthermia temperature (45 °C). It is often combined with chemotherapy for obtaining a more effective therapeutic outcome. Cubic-shaped cobalt ferrite nanoparticles (Co-Fe NCs) serve as magnetic hyperthermia agents and as a cytotoxic agent due to the known cobalt ion toxicity, allowing the achievement of both heat and cytotoxic effects from a single platform. In addition to this advantage, Co-Fe NCs have the unique ability to form growing chains under an alternating magnetic field (AMF). This unique chain formation, along with the mild hyperthermia and intrinsic cobalt toxicity, leads to complete tumor regression and improved overall survival in an in vivo murine xenograft model, all under clinically approved AMF conditions. Numerical calculations identify magnetic anisotropy as the main Co-Fe NCs' feature to generate such chain formations. This novel combination therapy can improve the effects of magnetic hyperthermia, inaugurating investigation of mechanical behaviors of nanoparticles under AMF, as a new avenue for cancer therapy.

Efficient degradation of bisphenol A in water by heterogeneous activation of peroxymonosulfate using highly active cobalt ferrite nanoparticles.

Cobalt ferrite CoFe2O4 catalyst was fabricated and systematically investigated as an efficient peroxymonosulfate (PMS, HSO5-) activator for the degradation of recalcitrant organic contaminants (ROCs) in water treatment. Both SO4- and OH on the surface of catalyst were unveiled to be primarily responsible for bisphenol A (BPA) degradation by a comprehensive study using electron paramagnetic resonance (EPR), radical scavengers and quantification of SO4-, and the negligible contribution of singlet oxygen (1O2) was also observed. BPA degradation was accelerated in the presence of humic acid, and it increased first but then decreased with the further addition of fulvic acid. Moreover, the presence of chloride and bicarbonate ions can enhance both BPA and TOC removal. The toxicity of the target aqueous solution ascended slowly at the early stage but then declined dramatically and almost vanished as the reaction proceeded. The removal efficiencies of other typical ROCs (clofibric acid, 2,4-dichlorophenol, etc.) and the decontamination of natural surface water spiked with BPA were also evaluated. This CoFe2O4/PMS process could be well applied as a safe, efficient, and sustainable approach for ROCs remediation in complex wastewater matrix.

Temperature-controlled magnetic nanoparticles hyperthermia inhibits primary tumor growth and metastases dissemination.

Magnetic hyperthermia (MHT) is a promising approach for cancer therapy. However, a systematic MHT characterization as function of temperature on the therapeutic efficiency is barely analyzed. Here, we first perform comparative temperature-dependent analysis of the cobalt ferrite nanoparticles-mediated MHT effectiveness in two murine tumors models - breast (4T1) and colon (CT26) cancer in vitro and in vivo. The overall MHT killing capacity in vitro increased with the temperature and CT26 cells were more sensitive than 4T1 when heated to 43 °C. Well in line with the in vitro data, such heating cured non-metastatic CT26 tumors in vivo, while only inhibiting metastatic 4T1 tumor growth without improving the overall survival. High-temperature MHT (>47 °C) resulted in complete 4T1 primary tumor clearance, 25-40% long-term survival rates, and, importantly, more effective prevention of metastasis comparing to surgical extraction. Thus, the specific MHT temperature must be defined for each tumor individually to ensure a successful antitumor therapy.

Ultrathin surface coated water-soluble cobalt ferrite nanoparticles with high magnetic heating efficiency and rapid in vivo clearance.

To obtain magnetic nanoparticles with high magnetic heating efficiency and rapid in vivo clearance, this study utilized an improved linear response theory model to theoretically simulate the specific absorption rate (SAR) value versus the particle size of cobalt ferrite nanoparticles (CFNPs). An accurate SAR curve consistent with experimental results was obtained using cubes instead of spheres as the shape of CFNPs, given that cube was closer to the actual shape of prepared CFNPs. Under the guidance of simulation, we predicted and prepared water-soluble cubic CFNPs of 10-13 nm in size, with an ultrathin surface coating less than 1 nm in thickness. These CFNPs were experimentally verified to have high magnetic heating efficiency and rapid in vivo clearance rate. Our CFNPs of 11.8 nm in size had a high intrinsic loss power of 12.11 nHm2/kg. Most of the cells were killed within 30 min under magnetic heating with CFNPs. In an in vivo study, these CFNPs can heat a tumor area to 45 °C (ΔT > 9 °C) within 120 s under a weak alternating magnetic field (27 kA/m, 115 kHz). Notably, these CFNPs had significant tumor inhibition rate in vivo and can be cleared from the body by more than 64% within 2 weeks, demonstrating excellent rapid in vivo clearance. This result was close to the clearance level of the magnetic resonance imaging contrast agent Feridex. Therefore, our CFNPs had high magnetic heating efficiency and rapid in vivo clearance rate, indicating their great potential for future clinical applications.

A novel electromagnetic biodegradable nanocomposite based on cellulose, polyaniline, and cobalt ferrite nanoparticles.

Biodegradable, antimicrobial, and semiconducting cellulosic composite was synthesized by in-situ polymerization of polyaniline in the presence of cellulose. The cobalt ferrite nanoparticles (CFO-NPs) were added during the polymerization process to acquire this composite magnetic property. The CFO-NPs were prepared by sol-gel method with average particles size less than 50 nm. The nanocomposites were characterized by Fourier-transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM) and energy-dispersive X-ray (EDX). In addition, their magnetic, dielectric constant, dielectric loss, and conductivity behaviors were studied. The magnetization (Ms) and conductivity increased up to 3.7 emu/g and 3.5 × 10-3 S/cm, respectively, with increasing CFO-NPs content. The prepared electromagnetic nanocomposite exhibits highly efficient biodegradability and antimicrobial activity against Escherichia coli, Bacillus subtilis, and Candida albicans. The antimicrobial activity increased with increasing CFO-NPs while the biodegradability decreased.

Targeted T1 Magnetic Resonance Imaging Contrast Enhancement with Extraordinarily Small CoFe2O4 Nanoparticles.

Extraordinarily small (2.4 nm) cobalt ferrite nanoparticles (ESCIoNs) were synthesized by a one-pot thermal decomposition approach to study their potential as magnetic resonance imaging (MRI) contrast agents. Fine size control was achieved using oleylamine alone, and annular dark-field scanning transmission electron microscopy revealed highly crystalline cubic spinel particles with atomic resolution. Ligand exchange with dimercaptosuccinic acid rendered the particles stable in physiological conditions with a hydrodynamic diameter of 12 nm. The particles displayed superparamagnetic properties and a low r2/ r1 ratio suitable for a T1 contrast agent. The particles were functionalized with bile acid, which improved biocompatibility by significant reduction of reactive oxygen species generation and is a first step toward liver-targeted T1 MRI. Our study demonstrates the potential of ESCIoNs as T1 MRI contrast agents.

Synthesis and characterization of metals-substituted cobalt ferrite [Mx Co(1-x) Fe2O4; (M = Zn, Cu and Mn; x = 0 and 0.5)] nanoparticles as antimicrobial agents and sensors for Anagrelide determination in biological samples.

Nanocrystalline spinel ferrite nanoparticles [MxCo(1-x)Fe2O4;(M = Zn,Cu,Mn;x = 0 and 0.5)] like: Cobalt ferrite (CFO), Zinc Cobalt ferrite (ZCFO), Copper Cobalt ferrite (CCFO), and Manganese Cobalt ferrite (MCFO) modified carbon paste electrodes (CPE) were synthesized via sol-gel technique utilizing citric acid and ethylene glycol as a polymerization agent. The synthesized ferrite NPs were used as bi-functional smart biosensor, not only used to determine the drug Anagrelide-HCl (ANDH) in urine and serum samples, but also possesses antimicrobial potential against some pathogenic microbes, founded in the biological samples. The synthesized ferrite NPs were confirmed by XRD, FTIR spectroscopy, SEM, EDX, and elemental mapping images. Antimicrobial activities of ferrite NPs against selected urinary tract infected microbes were investigated. From XRD data and FTIR spectroscopy it is found that the average crystallite size is lies in the range 12.86 to 33.92 ±â€¯1.5 nm, also the bond lengths RA and RB increase from 1.8986 to 1.9145 Šand from 2.0434 to 2.0606 Šrespectively and Debye temperature θD lies in the range of 681.52-708.87 K. Our study describes the improvement of a screen-printed sensor, modified with ferrite NPs materials for rapid, sensitive and cost-effective quantification of ANDH present in the real samples such as blood serum samples, urine and in the pharmaceutical formulations. The results obtained postulate a linear regression between the ANDH charge density of peak current and its concentration in the range from (0.64-8.18 µg/ml) with DL 0.31 µg/ml and QL 0.94 µg/ml. Antimicrobial results indicated that ZCFO NPs were a novel antibacterial agent against Klebsiella pneumoniae (28.0 mm ZOI), and multidrug-resistant bacteria Enterococcus faecalis (27.0 mm ZOI). Additionally, ZCFO NPs were active against Candida albicans (18.0 mm ZOI) seems to be a smart antifungal agent. Therefore, ZCFO NPs can be used as applicant resources for industrial, medical, and biological applications.

Investigate the ultrasound energy assisted adsorption mechanism of nickel(II) ions onto modified magnetic cobalt ferrite nanoparticles: Multivariate optimization.

In present study, magnetic cobalt ferrite nanoparticles modified with (E)-N-(2-nitrobenzylidene)-2-(2-(2-nitrophenyl)imidazolidine-1-yl) ethaneamine (CoFe2O4-NPs-NBNPIEA) was synthesized and applied as novel adsorbent for ultrasound energy assisted adsorption of nickel(II) ions (Ni2+) from aqueous solution. The prepared adsorbent characterized by Fourier transforms infrared spectroscopy (FT-IR), transmission electron microscope (TEM), vibrating sample magnetometer (VSM) and X-ray diffraction (XRD). The dependency of adsorption percentage to variables such as pH, initial Ni2+ ions concentration, adsorbent mass and ultrasound time were studied with response surface methodology (RSM) by considering the desirable functions. The quadratic model between the dependent and independent variables was built. The proposed method showed good agreement between the experimental data and predictive value, and it has been successfully employed to adsorption of Ni2+ ions from aqueous solution. Subsequently, the experimental equilibrium data at different concentration of Ni2+ ions and 10mg amount of adsorbent mass was fitted to conventional isotherm models like Langmuir, Freundlich, Tempkin, Dubinin-Radushkevich and it was revealed that the Langmuir is best model for explanation of behavior of experimental data. In addition, conventional kinetic models such as pseudo-first and second-order, Elovich and intraparticle diffusion were applied and it was seen that pseudo-second-order equation is suitable to fit the experimental data.