A synthetic and transparent clay removes Microcystis aeruginosa efficiently.

Clay-algae flocculation is a promising method to remove harmful algal blooms (HABs) in aquatic ecosystems. Many HAB-generating species, such as Microcystis aeruginosa (M. aeruginosa), a common species in lakes, produce toxins and harm the environment, human health, and the economy. Natural clays, such as bentonite and kaolinite, and modification of these clays have been applied to mitigate HABs by forming large aggregates and settling down. In this study, we aim to examine the impact of laponite, a commercially available smectite clay that is synthetic, transparent, compatible with human tissues, and degradable, on removing HABs. We compare the cell removal efficiencies (RE) of laponite, two natural clays, and their polyaluminum chloride (PAC)-modified versions through clay-algae flocculation experiments. Our results show that the optimum concentrations of laponite, bentonite, kaolinite, PAC-modified bentonite, and PAC-modified kaolinite to remove 80 % of the M. aeruginosa cells from the water column are 0.05 g/L, 2 g/L, 4 g/L, 2 g/L and 0.3 g/L respectively. Therefore, to achieve the same cell removal efficiency, the amount of laponite needed is 40 to 80 times less than bentonite and kaolinite, and 6 times less than PAC-modified kaolinite. We demonstrate that the superior performance of laponite clay is because of its smaller particle size, which increases the encounter rate between cells and clay particles. Furthermore, experiments using water samples from Powderhorn Lake confirmed laponite's effectiveness in mitigating HABs. Our price analysis also suggests that this commercially-available clay, laponite, can be used in the field at a relatively low cost.

Enhanced sludge dewatering using a novel synergistic iron/peroxymonosulfate-polyacrylamide method.

In the sludge dewatering process, a formidable challenge arises due to the robust interactions between extracellular polymeric substances (EPS) and bound water. This study introduces a novel, synergistic conditioning method that combines iron (Fe2+)/peroxymonosulfate (PMS) and polyacrylamide (PAM) to significantly enhance sludge dewatering efficiency. The application of the Fe2+/PMS-PAM conditioning method led to a substantial reduction in specific filtration resistance (SFR) by 82.75% and capillary suction time (CST) by 80.44%, marking a considerable improvement in dewatering performance. Comprehensive analyses revealed that pre-oxidation with Fe2+/PMS in the Fe2+/PMS-PAM process effectively degraded EPS, facilitating the release of bound water. Subsequently, PAM enhanced the flocculation of fine sludge particles resulting from the advanced oxidation processes (AOPs). Furthermore, analysis based on the Extended Derjaguin-Landau-Verwey-Overbeek (XDLVO) theory demonstrated shifts in interaction energies, highlighting the breakdown of energy barriers within the sludge and a transition in surface characteristics from hydrophilic (3.79 mJ m-2) to hydrophobic (-61.86 mJ m-2). This shift promoted the spontaneous aggregation of sludge particles. The innovative use of the Flory-Huggins theory provided insights into the sludge filtration mechanism from a chemical potential perspective, linking these changes to SFR. The introduction of Fe2+/PMS-PAM conditioning disrupted the uniformity of the EPS-formed gel layer, significantly reducing the chemical potential difference between the permeate and the water in the gel layer, leading to a lower SFR and enhanced dewatering performance. This thermodynamic approach significantly enhances our understanding of sludge dewatering and conditioning. These findings represent a paradigm shift, offering innovative strategies for sludge treatment and expanding our comprehension of dewatering and conditioning techniques.

Enhanced consolidation and removal of accumulated flocculants in dredged soil via leaching with vacuum preloading.

The vacuum preloading coupling flocculation treatment is a widely employed method for reinforcing soils with high water content in practical construction. However, uneven distribution and accumulation of flocculants pose significant damage to the soil environment and result in uneven soil consolidation, leading to severe issues in subsequent soil development and exploitation. To address these concerns, an evolved leaching with vacuum method is developed for facilitating soil consolidation while preventing the accumulation of flocculant in the soil. In this study, five model tests are conducted in which FeCl3 is chosen as the typical flocculant to promote soil consolidation, and deionized water is used for leaching. The final discharged water, settlement, water content and penetration resistance of soil are obtained to evaluate the soil reinforcement effect, while the flocculant removal effect is evaluated by the Fe3+ content in the filtrate and soil. The comprehensive reinforcement and flocculant removal effect show that this method is extremely effective compared to traditional vacuum preloading. The two leaching is clarified as the best choice, resulting in a 22% decrease in the soil water content and a 25% in soil penetration resistance, meanwhile a 12.8% removal rate of the flocculant. The test results demonstrate that leaching with vacuum preloading can contribute to promoting soil consolidation and reducing the accumulation of flocculant in the soil, ensuring the safe and eco-friendly use of the soil for future applications. The conclusions obtained are of significant theoretical value and technical support for practical construction and sustainable development.

New insights into membrane fouling in coagulation-ultrafiltration by cake characteristics analysis: A case study with PACl-Al13 and PACl.

Membrane fouling is a bottleneck issue that hindered the further application of ultrafiltration technology. To alleviate membrane fouling, coagulation-ultrafiltration (C-UF) process using polyaluminum chloride (PACl) and PACl-Al13 with high proportion of Al13O4(OH)247+ as coagulants, respectively, were investigated at various pH conditions. Results indicated that an increase in solution pH contributed to larger floc size and looser floc structure for both PACl and PACl-Al13. It was conducive to the formation of more porous cake, as evidenced by mean pore area and pore area distribution of cake, leading to lower reversible fouling. Furthermore, humic acid (HA) removal presented a trend of first increasing and then decreasing with the increase of pH. The optimal HA removal was achieved at pH 6 regardless of coagulant type, suggesting that the slightest irreversible fouling should be occurred at this point. Interestingly, the irreversible fouling with PACl coagulant achieved a minimum value at pH 9, while the minimal irreversible fouling with PACl-Al13 was observed at pH 6. We speculated that the cake formed by PACl could further intercept HA prior to UF process at alkaline pH. Furthermore, compared with PACl, PACl-Al13 had a stronger charge neutralization ability, thus contributing to more compact floc structure and higher HA removal at various pH conditions. By UF fractionation measurement, higher HA removal for PACl-Al13 was due to higher removal of HA with molecular weight less than 50 kDa.

Recent progress and perspectives of typical renewable bio-based flocculants: characteristics and application in wastewater treatment.

The research on bio-based flocculants for waste resource utilization and environmental protection has garnered significant attention. Bio-based flocculants encompass plant-based, animal-based, and microbial variants that are prepared and modified through biological, chemical, and physical methods. These flocculants possess abundant functional groups, unique structures, and distinctive characteristics. This review comprehensively discussed the removal rates of conventional pollutants and emerging pollutants by bio-based flocculants, the interaction between these flocculants and pollutants, their impact on flocculation performance in wastewater treatment, as well as their application cost. Furthermore, it described the common challenges faced by bio-based flocculants in practical applications along with various improvement strategies to address them. With their safety profile, environmental friendliness, efficiency, renewability, and wide availability from diverse sources, bio-based flocculants hold great potential for widespread use in wastewater treatment.

Harvesting of cyanobacteria and phosphorus by electrocoagulation-flocculation-flotation: Role of phosphorus precipitation in cell separations and organics destabilization.

A high level of phosphate triggers the excretion of algogenic organic matter (AOM) during algae blooming, leading to disinfection by-products (DBPs) formation. The presence of phosphate could impact cyanobacteria harvesting and AOM separations by electrocoagulation. This study aims to investigate the role of phosphate in cell separations and AOM destabilization by Al-based electrocoagulation-flocculation-flotation (EFF) for harvesting of cyanobacteria and phosphate. The Al-based EFF was conducted to harvest Microcystis aeruginosa (MA) with varied phosphate (0-10 mg/L) at 5 mA/cm2 and pH 8. Fluorescent organic fractions, molecular weight distributions, the properties of flocs and DBPs formation potential were fully investigated. The results showed that the EFF at a low level of phosphate (1 mg/L) effectively improves the harvesting of MA cells, phosphate and the reduction in dissolved organic matter (DOC) up to 99.5 %, 95 % and 50 %, respectively. However, the presence of concentrated phosphate (10 mg/L) alleviates cell harvesting and worsens AOM separations due to ineffective floc formation induced by the fast formation of inactive AlPO4 precipitates along with limited Al(OH)3. At such a condition, it worsens DBPs precursors minimization owing to AOM release from MA cells. The increase in the current density during EFF can compensate for cell harvesting efficiency even though at concentrated phosphate, but it further induces AOM release. It is concluded that Al-based EFF demonstrates an efficient harvesting of cyanobacteria, phosphorus and AOM separations from algae-laden water under phosphate impact.

Efficient, quick, and low-carbon removal mechanism of microplastics based on integrated gel coagulation-spontaneous flotation process.

To address the problems of unstable efficiency, long treatment period, and high energy consumption during microplastics (MPs) removal by traditional coagulation-flotation technology, a gel coagulation-spontaneous flotation (GCSF) process is proposed that employs laminarin (LA) as the crosslinker and polyaluminum chloride (PAC)/polyaluminum ferric chloride (PAFC) as the coagulant to remove MPs. Herein, the effects of GCSF chemical conditions on microplastic-humic acid composite pollutants (MP-HAs) removal were investigated, and the removal mechanisms were analyzed through theoretical calculations and floc structure characterization. Results showed that an LA to PAC/PAFC ratio of 2.5:1 achieved the highest removal of HA (86 %) and MPs (93 %-99 %) in short coagulation (< 1 min) and spontaneous flotation (< 9 min) period. PAC-LA exhibited strong removal ability for MP-HAs while PAFC-LA induced fast flotation speed. The peak intensity and peak shift in Fourier-transformed infrared and X-ray photo-electron spectra indicated that the removal mechanisms of MPs include hydrogen bond adsorption and the sweeping effect, mainly relying on -OH/-C = O on the MPs surface and entrapment of gel flocs with a high degree of aggregation, respectively. The extended Derjaguin-Landau-Verwey-Overbeek calculation also revealed that interactions between PAC/PAFC-LA and MP-HAs were mainly polar interaction (hydrogen bonding) and intermolecular attraction interaction (Lifshitz-van der Waals force), and the sweep effect was reflected by intermolecular interaction. In addition, density function theory calculations indicated that -OH in LA mainly adsorbs DO through a double hydrogen bond configuration, and the crosslinking ligand FeO6/AlO6 assists in DO absorption by -OH.

Performance evaluation of typical flocculants for efficient harvesting of Chlorella sorokiniana under different carbon application modes.

In this study, the growth characteristics of microalgae cultured with different carbon sources were analyzed, and the flocculation characteristics under the influence of carbon sources were evaluated using three typical flocculants. The results showed that the organic carbon sources could significantly increase the content of extracellular proteins in microalgae. Specifically, the extracellular protein concentrations of microalgae cultured with pure BG-11, ethanol, sodium acetate and glucose were 18.2 29.2, 97.3, and 34.7 mg/g, respectively. During the flocculation process, microalgae cultured with sodium acetate exhibited a weak response to the flocculant because of excessive extracellular proteins inhibited flocculation. In addition, the flocculation efficiency was also less than 50.0% cultured with sodium acetate in all pH test ranges when alum and chitosan were used as flocculants. It could be inferred that the flocculant initially happened to charge neutralization with the negatively charged proteins in the solution and then bridged the charges with the microalgae. These findings provide insights into the effects of different carbon sources on microalgal flocculation, promising organic integration of microalgae wastewater treatment and harvesting.

Influence of chitosan properties and operating parameters on the flocculation efficiency and harvesting of microalgae (Scenedesmus sp.).

Physicochemical and structural characteristics of chitosan prepared from Deep-sea shrimp (DCs), including degree of deacetylation (DD), molecular weight (Mw), viscosity, crystallinity index (CrI) and surface morphology were compared with a commercial chitosan (CCs). The DCs had a higher DD of 81.33 ± 0.40 %, whereas the CCs had a lower DD of 74.62 ± 0.64 %. Additionally, the DCs exhibited a lower Mw of 192.47 ± 2.5 kDa and viscosity of 646.00 ± 4.00 cP compared to the CCs, which had a Mw of 202.44 ± 0.28 kDa and viscosity of 689.67 ± 5.91 cP. This study investigated the influence of chitosan properties, particularly DD and Mw on the harvesting of Scenedesmus sp. along with the chitosan dosage, pH of the culture medium, mixing speed and time. Under optimal operating conditions, the microalgae removal efficiency of the DCs reached a significantly higher level (94.71 ± 0.20 %) compared to that of CCs (88.25 ± 0.41 %). Chitosan with a higher DD and low Mw demonstrated superior flocculation efficiency. The results highlight the significance of DD and Mw of chitosan and its influence on the flocculation of microalgae, providing valuable insights for optimizing the harvesting process with the non-toxic and natural flocculent, chitosan.

Characteristics and stabilization of Pickering emulsions constructed using myosin from bighead carp (Aristichthys nobilis).

Myosin from bighead carp (Aristichthys nobilis) as a main type of fish protein possesses a good emulsifying ability. However, whether bighead carp myosin (BCM) could construct stable Pickering emulsions is still unclear. Therefore, myosin particles and Pickering emulsions stabilized by bighead carp myosin (BCMPEs) were analyzed. The surface structure of BCM particles at 0.6 mol/L NaCl treatment was uniform and compact with a contact angle of 86.4 ± 2.7°, exhibiting the potential ability to construct O/W Pickering emulsions. The size and flocculation index (FI) of BCMPEs decreased with the increase in BCM concentrations of 1%-4% (w/v). Reversely, the size of BCMPEs increased with the increase in oil-water ratios. BCM particles could uniformly distribute at the oil-water interface to stabilize BCMPEs at a BCM concentration of 4% (w/v) and an oil-water ratio of 6:4 (v/v). This study could help explore fish proteins to construct Pickering emulsions for the deep processing of fish products.

Investigating flocculation mechanisms and ecological safety of cationic guar gum for rapid harvesting of microalgal cells.

Addressing the drawbacks of traditional flocculants on microalgae biomass harvesting is crucial for large-scale industrial applications of microalgae production. In this study, cationic bioflocculant was successfully prepared by introducing cationic groups into the side chain of guar gum, achieving in-situ algae flocculation efficiency of 83.5 % with the dosage of 18.0 mg/L under pH = 10.0. Through a harmonious integration of predictive modelling and practical experimentation, a superior cell flocculation capacity of 23.5 g/g was achieved. In addition, the environmental safety and biocompatibility of cationic guar gum was assessed, using the typical suspension quantitative bacteriostatic method and the fluorescent double-staining technique. The results showed that the inhibition efficiency of Staphylococcus aureus in the system containing 60.0 mg/L cationic guar gum was only 12.0 % and there was no inhibition against Escherichia coli colonies. These findings provide a safe and green flocculant for efficient microalgae harvesting and spent medium treatment.

Microalgal extracellular polymeric substances (EPS) and their roles in cultivation, biomass harvesting, and bioproducts extraction.

Microalgae extracellular polymeric substances (EPS) are complex high-molecular-weight polymers and the physicochemical properties of EPS strongly affect the core features of microalgae cultivation and resource utilization. Revealing the key roles of EPS in microalgae life-cycle processes in an interesting and novelty topic to achieve energy-efficient practical application of microalgae. This review found that EPS showed positive effect in non-gas uptake, extracellular electron transfer, toxicity resistance and heterotrophic symbiosis, but negative impact in gas transfer and light utilization during microalgae cultivation. For biomass harvesting, EPS favored biomass flocculation and large-size cell self-flocculation, but unfavored small size microalgae self-flocculation, membrane filtration, charge neutralization and biomass dewatering. During bioproducts extraction, EPS exhibited positive impact in extractant uptake, but the opposite effect in cellular membrane permeability and cell rupture. Future research on microalgal EPS were also identified, which offer suggestions for comprehensive understanding of microalgal EPS roles in various scenarios.

Effects of residual foaming agent and defoamer on defoaming-flocculation-filterpress characteristics of earth pressure balance shield muck.

Foaming agents as a combination of several components are usually used as soil conditioning during earth pressure balance shield (EPBS) tunnelling. These residues in waste EPBS muck lead to a series of new challenges for in-situ recycling, i.e., foams overflow flocculation tank. This study investigates the effects of residual foaming agent components and defoamers on defoaming-flocculation-filterpress characteristics of EPBS muck using an improved flocculation and filterpress system. Residual foam height (Hf), defoaming ratio (DFR), antifoaming ratio (AFR), total suspended substance (TSS), turbidity, moisture content (MC), and zeta potential (ZP) were selected as characterization indices. The microstructure of filterpress cakes was analyzed using a scanning electron microscope. Results demonstrate that an enhancement within 0.0-1.0wt.% for sodium fatty alcohol polyoxyethylene ether sulfate (AES) and alpha olefin sulfonate (AOS) significantly reduces DFR and AFR. The MC and ZP decline, while the Hf and turbidity enhance. The combinations of nonionic surfactants alkyl polyglycoside (APG) and fatty alcohol-polyoxyethylene ether (AEO) in a concentration range of 0.0-1.0wt.% with 0.2wt.% AES causes the Hf, DFR, AFR, turbidity, and ZP to exhibit absolutely different variations. The MC with the growth in both APG and AEO presents a trend of first decreasing and then increasing. By increasing foam stabilizers sodium carboxymethyl cellulose (CMC) and guar gum (GG) within 0.02-0.10wt.%, the AFR, TSS, and ZP enhance in varying degrees, while the Hf, DFR, and MC gradually reduce. With the increase of defoamers hydroxyl silicone oil-glycerol polyoxypropylene ether (H-G) and dimethyl silicone oil-glycerol polyoxypropylene ether (D-G) within 0.002-0.010wt.%, the DFR and AFR are significantly improved, while the TSS, turbidity, MC, and ZP display varying degrees of reduction. Moreover, defoaming-flocculation-filterpress mechanisms of EPBS muck are explored to provide a useful reference for actual in-situ recycling projects.

Multi-interface interaction mechanism of pulp reject-based flocculants for the removal of antibiotics and its combined pollutants.

The efficient removal of antibiotics and its combined pollutants is essential for aquatic environment and human health. In this study, a lignin-based organic flocculant named PRL-VAc-DMC was synthesized using pulp reject as the raw material, with vinyl acetate (VAc) and methacryloxyethyltrimethyl ammonium chloride (DMC) as the grafting monomers. A series of modern characterization methods were used to confirm the successful preparation of PRL-VAc-DMC and elucidate its polymerization mechanism. It was found that the Ph-OH group and its contiguous carbon atoms of lignin served as the primary active sites to react with grafting monomers. Flocculation experiments revealed that PRL-VAc-DMC could react with tetracycline (TC) through π-π* interaction, hydrophobic interaction, hydrogen bonding, and electrostatic attraction. With the coexistence of humic acid (HA) and Kaolin, the aromatic ring, hydroxyl, and amide group of TC could react with the benzene ring, hydroxyl group, and carboxyl group of HA, forming TC@HA@Kaolin complexes with Kaolin particles acting as the hydrophilic shell. The increase in particle size, electronegativity, and hydrophily of TC@HA@Kaolin complexes facilitated their interaction with PRL-VAc-DMC through strong interfacial interactions. Consequently, the presence of HA and Kaolin promoted the removal of TC. The synergistic removal mechanism of TC, HA, and Kaolin by PRL-VAc-DMC was systematically analyzed from the perspective of muti-interface interactions. This paper is of great significance for the comprehensive utilization of pulp reject and provides new insights into the flocculation mechanism at the molecular scale.

Deep learning-based flocculation sensor for automatic control of flocculant dose in sludge dewatering processes during wastewater treatment.

In sludge dewatering of most wastewater treatment plants (WWTPs), the dose of polymer flocculant is manually adjusted through direct visual inspection of the flocs without the aid of any instruments. Although there is a demand for the development of automatic control of flocculant dosing, this has been challenging owing to the lack of a reliable flocculation sensor. To address this issue, this study developed a novel image sensor for measuring the degree of flocculation (DF) based on deep learning. Two types of sludge samples were used in the laboratory-scale flocculation tests: excess sludge and mixtures of excess sludge and raw wastewater. To search for a deep learning regression model suitable for DF inference, ten models, including convolutional neural networks, vision transformers, and a multilayer perceptron MLP mixer, were comparatively analysed. The ConvNeXt and MLP mixer models showed the highest accuracies with coefficients of determination (R2) greater than 0.9. The region contributing to the DF inference in the flocculation images was visualised using a modulus-weighted, gradient-weighted regression activation map. A prototype of the flocculation sensor was constructed using an inexpensive EdgeAI device. This device comprises a single-board computer and an integrated graphical processing unit (GPU) and is equipped with a quantised ConvNeXt model. The maximum inference speed of the sensor was 12.8 frames per second (FPS). The flocculation control tests showed that the sensor could control the DF to the target value by adjusting the polymer flocculant dose. Therefore, the flocculation sensor can provide a data-driven approach to the management of the flocculation process, thereby facilitating the automation of WWTPs.

Pickering emulsion stabilization with colloidal lignin is enhanced by salt-induced networking in the aqueous phase.

We study the effect of electrolytes on the stability in aqueous media of spherical lignin particles (LP) and its relevance to Pickering emulsion stabilization. Factors considered included the role of ionic strength on morphology development, LP size distribution, surface charge, interfacial adsorption, colloidal and wetting behaviors. Stable emulsions are formed at salt concentrations as low as 50 mM, with the highest stability observed at a critical concentration (400 mM). We show salt-induced destabilization of LP aqueous dispersions at an ionic strength >400 mM. At this critical concentration LP flocculation takes place and particulate networks are formed. This has a profound consequence on the stability of LP-stabilized Pickering emulsions, affecting rheology and long-term stability. The results along with quartz microgravimetry and confocal microscopy observations suggest a possible mechanism for stabilization that considers the interfacial adsorption of LP at oil/water interfaces. The often-unwanted colloidal LP destabilization in water ensues remarkably stable Pickering emulsions by the effect of network formation.

Natural flocculant chitosan inhibits short-chain fatty acid production in anaerobic fermentation of waste activated sludge.

Chitosan (CTS) serves as an excellent natural flocculant in wastewater purification and sludge conditioning, but its potential impact on anaerobic fermentation of waste-activated sludge is unclear. The current study investigated the role of CTS in short-chain fatty acids (SCFAs) generation via sludge alkaline anaerobic fermentation. The results showed a drastic reduction in SCFA production with CTS, showing a maximum inhibition of 33 % at 6 mg/g of total suspended solids. CTS hindered sludge solubilization through flocculation, and acted as a humus precursor, promoting humus formation, and consequently reduced the amount of available substrates. Further, CTS promoted free ammonia production, posing a challenge to enzymes and cell viability. Additionally, CTS increased the population of Rikenellaceae sp. and weakened the dominance of hydrolyzing and acidifying bacteria. This study deepens the understanding of the potential impact of CTS on anaerobic fermentation and provides a theoretical basis for reducing the risk of polymeric flocculants.

Enhanced biomass production and harvesting efficiency of Chlamydomonas reinhardtii under high-ammonium conditions by powdered oyster shell.

Chlamydomonas reinhardtii prefers ammonium (NH4+) as a nitrogen source, but its late-stage growth under high-NH4+ concentrations (0.5 âˆ¼ 1 g/L) is retarded due to medium acidification. In this study, oyster shell powders were shown to increase the tolerance of C. reinhardtii to NH4+ supplementation at 0.7 g/L in TAP medium in 1-L bubble-column bioreactors, resulting in a 22.9 % increase in biomass production, 62.1 % rise in unsaturated fatty acid accumulation, and 19.2 % improvement in harvesting efficiency. Powdered oyster shell mitigated medium acidification (pH 7.2-7.8) and provided dissolved inorganic carbon up to 8.02 × 103 µmol/L, facilitating a 76.3 % NH4+ consumption, release of up to 189 mg/L of Ca2+, a 42.1 % reduction in ζ-potential and 27.7 % increase in flocculation activity of microalgae cells. This study highlights a promising approach to utilize powdered oyster shell as a liming agent, supplement carbon source, and bio-flocculant for enhancing biomass production and microalgae harvesting in NH4+-rich environments.

Two-stage injection of polymer and microsand during ballasted flocculation for treating kaolin waters with or without humic acid: Floc evolutional characteristics, performance and mechanisms.

Ballasted flocculation is regarded as a most promising water treatment technology in aspects of retrofit and high-rate applications. To deep understand the incorporation behaviors of ballasting agent into ballasted floc growth, two distinct injection modes (namely a two-stage injection of polyacrylamide (PAM) alone, and a two-stage injection of both PAM and microsand) were developed in this study. Then, ballasted flocculation tests of kaolin and kaolin-HA (humic acid) waters were conducted at varying split ratios for fixed total dosages of both PAM and microsand. The experimental results showed that for either two-stage injection mode, the higher the second percentage of each split ratio, the greater the average size of maturated flocs at the second sub-stage of maturation. Meanwhile, the turbidity and UV254 values of settled water became lower at 30 and 180 s of sedimentation, suggesting that varying split ratios significantly affected the kinetics of ballasted floc growth. Moreover, it was suggested that the selection of either two-stage injection mode or corresponding split ratios played a more pronounced role in the HA removal than the total dosage of PAM. This suggestion was supported by SEM, FTIR and XPS analyses for surface morphological details, functional groups and chemical states of maturated flocs eventually formed in the kaolin-HA water through both two-stage injection modes. Accordingly, newly-established conceptual models of ballasted floc growth were proposed to explore the potential influencing mechanisms of varying split ratios on the ballasted flocculation performance. At each sub-stage of maturation, an appropriate dosage ratio between PAM and microsand was of great importance to effectively incorporate microsand particles into ballasted floc formation, besides the hydrolyzed produces of AS coagulant formed at the coagulation stage of ballasted flocculation. This study is expected to provide valuable insights for making ballasted flocculation more effective, economical and sustainable in water treatment engineering.

The use of coagulant and natural soil to control cyanobacterial blooms in a tropical reservoir.

Cyanobacterial blooms have been a growing problem in water bodies and attracted attention from researcher and water companies worldwide. Different treatment methods have been researched and applied either inside water treatment plants or directly into reservoirs. We tested a combination of coagulants, polyaluminium chloride (PAC) and iron(III) chloride (FeCl3), and ballasts, luvisol (LUV) and planosol (PLAN), known as the 'Floc and Sink' technique, to remove positively buoyant cyanobacteria from a tropical reservoir water. Response Surface Methodology (RSM) based on Central Composite Design (CCD) was used to optimize the two reaction variables - coagulant dosage (x1) and ballast dosage (x2) to remove the response variables: chlorophyll-a, turbidity, true color, and organic matter. Results showed that the combination of LUV with PAC effectively reduced the concentration of the response variables, while PLAN was ineffective in removing cyanobacteria when combined to PAC or FeCl3. Furthermore, FeCl3 presented poorer floc formation and lower removal efficiency compared to PAC. This study may contribute to the theoretical and practical knowledge of the algal biomass removal for mitigating eutrophication trough different dosages of coagulants and ballasts.