Self-assembly peptide P11-4 induces mineralization and cell-migration of odontoblast-like cells.

OBJECTIVES: Self-assembling peptide P11-4 is amphiphilic and pH-triggered, effective on repairing early enamel carious lesions and dentin remineralization. However, P11-4 effects on dentin biomineralization and repair ability remain unexplored. Thus, cytocompatibility and effectiveness of P11-4 on inducing mineralization and migration of odontoblast-like cells (MDPC-23) were investigated. METHODS: MDPC-23 were seeded in contact with P11-4 (0.5 and 1 µg/ml), Dentin Matrix Protein 1 (DMP1 0.5 and 1 µg/ml) or Calcium hydroxide (Ca(OH)2 100 µg/ml) solutions. Cell viability was verified using MTT (n = 6/group). Mineral deposition was tested using Alizarin Red (n = 4/group). Cell migration was assessed by light microscopy (n = 2/group). MTT and Alizarin Red data were compared using Kruskal-Wallis and Mann-Whitney (α=0.01). RESULTS: P11-4 (0.5 and 1 µg/ml) and DMP1 (0.5 and 1 µg/ml) resulted the highest cell viability; Ca(OH)2 presented the lowest. 1 µg/ml DMP1 and 1 µg/ml P11-4 promoted the highest mineral deposition. Ca(OH)2 presented lower values of mineral deposits than DMP1 1 µg/ml (p < 0.01), but similar to P11-4 1 µg/ml. P11-4 and DMP1 at 0.5 µg/ml induced lesser mineral precipitation than P11-4 and DMP1 at 1 µg/ml (p < 0.01), with no difference to Ca(OH)2. All materials stimulated cell migration, however, lower concentrations of DMP1 and P11-4 demonstrated a higher migration potential. CONCLUSION: P11-4 did not affect cell viability, induces mineral deposition and MDPC-23 migration like DMP1. CLINICAL SIGNIFICANCE: Self-assembling peptide P11-4 does not affect the cell viability and induces mineral deposition comparable to native protein involved in biomineralization. Combined with its ability to bind type I collagen, P11-4 is a promising bioinspired molecule that provides native-tissue conditions and foster further studies on its ability to form dentin bridges in pulp-capping strategies.

Effect of additives on the compressive strength and setting time of a Portland cement.

Improvements in strength and setting time of Portland cements (PC) are needed to enhance their performance as endodontic and load bearing materials. This study sought to enhance the compressive strength and setting time of a PC by adding one of the following additives: 20% and 30% poly-methylmethacrylate (PMMA), 20% and 30% irregular and spherical amalgam alloys, and 10% CaCl(2). The control consisted of unreinforced PC specimens. Setting time was determined using a Gillmore apparatus according to standardized methods while compressive strength was measured using a universal testing machine after 21 hours or 60 days of water storage. Data were analyzed by ANOVA, Tukey and Games-Howell tests (alpha = 5%). All additives significantly decreased both initial and final setting times as compared with the PC-control (p < .05). 30% PMMA and 30% irregular alloy had the lowest values of initial setting time. 30% irregular alloy also produced the lowest values of final setting time while 30% spherical alloy yielded the highest (p < .05). No differences were detected between the compressive strength values of 21 hours and 60 days. While 10% CaCl(2), 20% and 30% PMMA produced values significantly lower than the PC-control, 30% spherical alloy significantly improved the compressive strength of the reinforced PC (p < .05). In summary, all additives significantly reduced the setting time and 30% spherical amalgam alloy yielded a significant increase in compressive strength for the tested PC, which might represent an improved composition for PCs to expand their use as endodontic and potentially load bearing materials.

Effect of additives on the compressive strength and setting time of a Portland cement

Improvements in strength and setting time of Portland cements (PC) are needed to enhance their performance as endodontic and load bearing materials. This study sought to enhance the compressive strength and setting time of a PC by adding one of the following additives: 20 percent and 30 percent poly-methylmethacrylate (PMMA), 20 percent and 30 percent irregular and spherical amalgam alloys, and 10 percent CaCl2. The control consisted of unreinforced PC specimens. Setting time was determined using a Gillmore apparatus according to standardized methods while compressive strength was measured using a universal testing machine after 21 hours or 60 days of water storage. Data were analyzed by ANOVA, Tukey and Games-Howell tests (á = 5 percent). All additives significantly decreased both initial and final setting times as compared with the PC-control (p < .05). 30 percent PMMA and 30 percent irregular alloy had the lowest values of initial setting time. 30 percent irregular alloy also produced the lowest values of final setting time while 30 percent spherical alloy yielded the highest (p < .05). No differences were detected between the compressive strength values of 21 hours and 60 days. While 10 percent CaCl2, 20 percent and 30 percent PMMA produced values significantly lower than the PC-control, 30 percent spherical alloy significantly improved the compressive strength of the reinforced PC (p < .05). In summary, all additives significantly reduced the setting time and 30 percent spherical amalgam alloy yielded a significant increase in compressive strength for the tested PC, which might represent an improved composition for PCs to expand their use as endodontic and potentially load bearing materials.