ABSTRACT
The identification of more efficient, clean, secure, and competitive energy supply is necessary to align with the needs of sustainable devices. For this reason, a study for developing innovative dye-sensitized solar cells (DSSCs) based on microbial pigments is reported starting from Talaromyces atroroseus GH2. The fungus was cultivated by fermentation and the extracellular pigment extract was characterized by HPLC-DAD-ESI-MS analyses. The most abundant compound among the 22 azaphilone-type pigments identified was represented by PP-O. The device's behavior was investigated in relation to electrolyte and pH for verifying the stability on time and the photovoltaic performance. Devices obtained were characterized by UV-vis measurements to verify the absorbance intensity and transmittance percentage. Moreover, photovoltaic parameters through photo-electrochemical measurements (I-V curves) and impedance characteristics by Electrochemical Impedance Spectroscopy (EIS) were determined. The best microbial device showed a short-circuit current density (Jsc) of 0.69 mA/cm2, an open-circuit photo-voltage (Voc) of 0.27 V and a Fill Factor (FF) of 0.60. Furthermore, the power conversion efficiency (PCE) of the device was 0.11%. Thus, the present study demonstrated the potential of microbial origin pigments for developing DSSCs.
Subject(s)
Coloring Agents , Solar Energy , Talaromyces , Talaromyces/chemistry , Talaromyces/metabolism , Coloring Agents/chemistry , Pigments, Biological/chemistryABSTRACT
In this study, two boronic acid BODIPYs are obtained through a microwave-assisted Knoevenagel reaction. The aim is to use them for the first time as dyes in a photosensitized solar cell (DSSC) to mimic chlorophyll photosynthesis, harvesting solar light and converting it into electricity. The microwave-assisted Knoevenagel reaction is a straightforward approach to extending the molecular conjugation of the dye and is applied for the first time to synthesize BODIPY's boronic acid derivatives. These derivatives have proved to be very useful for covalent deposition on titania. This work studies the photo-physical and electrochemical properties. Moreover, the photovoltaic performances of these two new dyes as sensitizers for DSSC are discussed. Experimental data show that both dyes exhibit photosensitizing activities in acetonitrile and water. In particular, in all the experiments, distyryl BODIPY was more efficient than styryl BODIPY. In this study, demonstrating the use of a natural component as a water-based electrolyte for boronic BODIPY sensitizers, we open new possibilities for the development of water-based solar cells.
ABSTRACT
A gold nanoparticles transparent electrode was realized by chemical reduction. This work aims to compare the transparent gold nanoparticles electrode with a more commonly utilized gold-film-coated electrode in order to investigate its potential use as counter-electrode (CE) in dye-sensitized solar cells (DSSCs). A series of DSSC devices, utilizing I-/I3- and Co(III)/(II) polypyridine redox mediators [Co(dtb)3]3+/2+; dtb = 4,4'ditert-butyl-2,2'-bipyridine)], were evaluated. The investigation focused firstly on the structural characterization of the deposited gold layers and then on the electrochemical study. The novelty of the work is the realization of a gold nanoparticles CE that reached 80% of average visible transmittance. We finally examined the performance of the transparent gold nanoparticles CE in DSSC devices. A maximum power conversion efficiency (PCE) of 4.56% was obtained with a commercial I-/I3--based electrolyte, while a maximum 3.1% of PCE was obtained with the homemade Co-based electrolyte.
ABSTRACT
An optimization work on dye-sensitized solar cells (DSSCs) based on both artificial and natural dyes was carried out by a fine synthesis work embedding gold nanoparticles in a TiO2 semiconductor and perfecting the TiO2 particle sizes of the scattering layer. Noble metal nanostructures are known for the surface plasmon resonance peculiarity that reveals unique properties and has been implemented in several fields such as sensing, photocatalysis, optical antennas and PV devices. By embedding gold nanoparticles in the mesoporous TiO2 layer and adding a scattering layer, we were able to boost the power conversion efficiency (PCE) to 10.8%, using an organic ruthenium complex. The same implementation was carried out using a natural dye, betalains, extracted from Sicilian prickly pear. In this case, the conversion efficiency doubled from 1 to 2% (measured at 1 SUN illumination, 100 mW/cm2 under solar simulation irradiation). Moreover, we obtained (measured at 0.1 SUN, 10 mW/cm2 under blue light LED irradiation) a record efficiency of 15% with the betalain-based dye, paving the way for indoor applications in organic natural devices. Finally, an attempt to scale up the system is shown, and a betalain-based- dye-sensitized solar module (DSSM), with an active area of 43.2 cm2 and a PCE of 1.02%, was fabricated for the first time.
ABSTRACT
In the ever-increasing energy demand scenario, the development of novel photovoltaic (PV) technologies is considered to be one of the key solutions to fulfil the energy request. In this context, graphene and related two-dimensional (2D) materials (GRMs), including nonlayered 2D materials and 2D perovskites, as well as their hybrid systems, are emerging as promising candidates to drive innovation in PV technologies. The mechanical, thermal, and optoelectronic properties of GRMs can be exploited in different active components of solar cells to design next-generation devices. These components include front (transparent) and back conductive electrodes, charge transporting layers, and interconnecting/recombination layers, as well as photoactive layers. The production and processing of GRMs in the liquid phase, coupled with the ability to "on-demand" tune their optoelectronic properties exploiting wet-chemical functionalization, enable their effective integration in advanced PV devices through scalable, reliable, and inexpensive printing/coating processes. Herein, we review the progresses in the use of solution-processed 2D materials in organic solar cells, dye-sensitized solar cells, perovskite solar cells, quantum dot solar cells, and organic-inorganic hybrid solar cells, as well as in tandem systems. We first provide a brief introduction on the properties of 2D materials and their production methods by solution-processing routes. Then, we discuss the functionality of 2D materials for electrodes, photoactive layer components/additives, charge transporting layers, and interconnecting layers through figures of merit, which allow the performance of solar cells to be determined and compared with the state-of-the-art values. We finally outline the roadmap for the further exploitation of solution-processed 2D materials to boost the performance of PV devices.
ABSTRACT
The development of novel, highly efficient, reliable, and robust surface enhanced Raman scattering (SERS) substrates containing a large number of hot spots with programmed size, geometry, and density is extremely interesting since it allows the sensing of numerous (bio-)chemical species. Herein, an extremely reliable, easy to fabricate, and label-free SERS sensing platform based on metal nanoparticles (NPs) thin-film is developed by the layer-by-layer growth mediated by polyelectrolytes. A systematic study of the effect of NP composition and size, as well as the number of deposition steps on the substrate's performance, is accomplished by monitoring the SERS enhancement of 1-naphtalenethiol (532 nm excitation). Distinct evidence of the key role played by the interlayer (poly(diallyldimethylammonium chloride) (PDDA) or PDDA-functionalized graphene oxide (GO@PDDA)) on the overall SERS efficiency of the plasmonic platforms is provided, revealing in the latter the formation of more uniform hot spots by regulating the interparticle distances to 5 ± 1 nm. The SERS platform efficiency is demonstrated via its high analytical enhancement factor (≈106 ) and the detection of a prototypical substance(tamoxifen), both in Milli-Q water and in a real matrix, viz. tap water, opening perspectives towards the use of plasmonic platforms for future high-performance sensing applications.
Subject(s)
Gold , Metal Nanoparticles , Polyelectrolytes , Spectrum Analysis, Raman , WaterABSTRACT
In the present work, five 2-styryl-1-benzopyrylium salts and their relative self-assembly processes towards TiO2 nanocrystalline layers were evaluated as photosensitizers in dye-sensitized solar cells (DSSCs). Integration of these 2-styryl-1-benzopyrylium salts with the semiconductor allow for the performance of highly specific functions suitable for smart applications in material science. Spectroscopic and photoelectrochemical measurements conducted on these five bio-inspired dyes, in solution and upon adsorption onto titanium dioxide films, allowed detailed discussion of the anchoring ability of the different donor groups decorating the 2-styryl-1-benzopyrylium core and have demonstrated their ability as photosensitizers. Our results suggest that the introduction of a dimethylamino group in position 4' of the 2-styryl-1-benzopyrylium skeleton can alter the conjugation of the molecule leading to larger absorption in the visible region and a stronger electron injection of the dye into the conduction band of TiO2. Moreover, our experimental data have been supported by theoretical calculations with the aim to study the energy of the excited states of the five compounds. In this specific case, the simulations reported contributed to better describe the properties of the compounds used and to help create the necessary basis for the design of new and targeted bio-inspired molecules.
ABSTRACT
Anthocyanins and anthocyanidins are polyphenolic compounds, responsible for the red and blue colours in several fruits, flowers, and leaves. Their colorant properties, bioavailability and antioxidant activity, made anthocyanins and anthocyanidins largely adopted in food and pharmaceutical industries. In this body of work, we firstly introduced structure, photophysical properties, co-pigmentation, antioxidant properties, glycosylation and complexation of anthocyanins and anthocyanidins. Secondly, we reported the computational methods adopted and the main theoretical results involving either anthocyanins and anthocyanidins, ranging from the first theoretical investigation on the structure of flavylium ions to the most recent studies on anthocyanins adsorbed on TiO2. We reviewed the computational contributions to the description of molecular properties of anthocyanins and anthocyanidins, giving a particular attention to the geometries, the spectroscopic features and the complexation properties of such molecules. Nowadays, theoretical calculations represent an essential methodology to understand and predict the chemical and physical properties of anthocyanins and their derivates.
Subject(s)
Anthocyanins/chemistry , Antioxidants/chemistry , Adsorption , Anthocyanins/analysis , Glycosylation , Pigmentation , Quantum Theory , Solar EnergyABSTRACT
Dye-sensitized solar cells (DSSCs) composed of aqueous electrolytes represent an environmentally friendly, low-cost, and concrete alternative to standard DSSCs and typical solar cells. Although flammable and toxic organic-solvent-based electrolytes have so far been employed more than simpler (iodide) aqueous solutions, recently recorded efficiencies of water-based DSSCs suggest a trend inversion in the near future. Here, we present a study, based on both experiments and ab initio molecular dynamics simulations, in which assessments on the efficiencies of three water electrolytes commonly employed in DSSCs (i.e., LiI, NaI, and KI) are reported. In particular, by atomistically tracing the ability of the iodides as charge carriers and by experimentally measuring the generated currents, we demonstrate that NaI aqueous solutions are more efficient electrolytes than LiI and KI - in descending order - in transporting electrons in DSSCs under bias. Monitoring the role played by the hydration shells of the ionic species under an electric field, we interpret, by first-principles, the various iodide mobilities. This finding, when combined with general considerations on the cation-induced effects on the TiO2 electronic structure, is able to account for the distinct efficiencies of the investigated electrolytes.
ABSTRACT
A series of six homoleptic bis-cyclometalated ruthenium complexes, Ru(N^N^C)2, is reported where N^N^C is a 6-(2,4-difluoro-3-R3-phenyl)-4-R2-4'-R1-2,2'-bipyridine with R3 = -H or -CF3 and R2 and R1 = -COOEt or -CF3. An effective synthesis of the ligands and the complexes is described. The UV-visible absorption studies demonstrate that these complexes are panchromatic dyes absorbing up to 900 nm. Importantly, the onset of absorption depends only on the substitution on the metalated phenyl, whereas the intensity of absorption throughout the spectra is a function of substituents on both the phenyl and the bipyridine moieties. The same trend is observed in electrochemistry as the redox gap depends only on the substitution on the metalated phenyl, whereas the oxidation and reduction potentials are a function of substituents on both the phenyl and the bipyridine moieties. Preliminary tests as sensitizer for dye-sensitized solar cells demonstrate that the number of anchoring groups on the dye has a major influence on the device efficiency.
ABSTRACT
We present here a complete study on four synthetic environmentally friendly flavylium salts employed as sensitizers for dye-sensitized solar cells (DSSCs). The effect of several donor groups on the molecular structure of flavylium ions was investigated by combining electrochemical, spectroscopic and computational means. The computational investigation indicated that these molecules can interact strongly with the TiO2 surface by a single OH group of the dihydroxybenzene moiety, and can efficiently inject electrons into the TiO2 following the excitation of their lowest singlet states exhibiting charge transfer (CT) character. In general, all dyes within the explored series exhibited quite good regeneration efficiencies, often ≥70%, in the presence of an iodide electron donor, explaining the high IPCEs and photocurrents recorded in the presence of high lithium content electrolytes. The combination of molecular orbital calculations and electrochemical measurements has also revealed that the introduction of donor groups on the benzopyrylium ring has a generally positive effect resulting in an extended low energy light harvesting and in a potential improvement of the photoinduced charge separation at the semiconductor/dye/electrolyte interface. It also increases the reversibility of the oxidative redox processes of these bio-inspired species, a feature in favour of their long-term stability. At present the best dye within the explored series is 7-(N,N-diethylamino)-3',4'-dihydroxyflavylium chloride based on a dialkylamine donor which is capable of delivering, under optimized conditions, a short-circuit current density of 15 mA cm-2. This is the highest value so far obtained for synthetic analogues of anthocyanins.
ABSTRACT
We have analyzed the excited state dynamics of the heteroleptic [(NCS)2Ru(bpy-(COOH)2)(bpy-(C6H13)2)] Z907 solar cell sensitizer in solution and when adsorbed onto thin TiO2 films, by combining transient visible and infrared (IR) spectroscopies with ab initio Density Functional Theory (DFT) and Time-Dependent DFT (TDDFT) calculations. Upon excitation with ultra-short pulses in ethanol and dimethyl-sulphoxide solutions, the visible spectra show the appearance of a positive signal around 650 nm, within the instrumental time resolution (<100 fs), which in ethanol undergoes a red-shift in about 20 ps. Measurements in the IR indicate that, upon excitation, both the CN and CO marker bands, associated with the NCS and COOH groups, downshift in frequency, in response to intramolecular ligand + metal (Ru-NCS) to ligand' (bpy-COOH2) charge transfer (LML'CT). Vibrational cooling is observed in both solvents; in ethanol it is overtaken by the hydrogen bond dynamics. On the basis of DFT/TDDFT calculations, explicitly modeling the interaction of the NCS and COOH groups with solvent (ethanol) molecules, we rationalize the observed IR and visible spectral evolution as arising from the change in the hydrogen-bond network, which accompanies the transition to the lowest-energy triplet state. This interpretation provides a consistent explanation of what is also observed in the transient visible spectra. Transient IR measurements repeated for molecules adsorbed on TiO2 and ZrO2 films, allow us to identify the structural changes signaling the dye triplet excited state formation and evidence multiexponential electron injection rates into the semiconductor TiO2 film.
ABSTRACT
This study reports on characterization and photoactivity of nanostructured TiO2 samples, which have been permanently densified under high pressures, up to 2.1 GPa. Commercial Mirkat 211 anatase has been used as a benchmark sample, in order to investigate the effect of unidirectional high pressure on structural, optical and photocatalytic properties of TiO2. Vibrational Raman spectroscopy shows that the treatment does not cause transitions among the different crystalline phases of titanium dioxide. UV-vis diffuse reflectance spectra reveal that increasing pressure gives rise to a shift of the absorption onset towards higher wavelength enhancing the photoactivity under visible radiation. Samples are also photo-electrochemically characterized and tested in the gas phase with partial oxidation of ethanol to acetaldehyde under visible irradiation. Compaction up to 0.8 GPa depresses both the alcohol conversion and the aldehyde yield, while samples treated under higher pressures show enhanced characteristics of conversion compared to the pristine material. Moreover, promising results in the reduction of CO2 are also obtained under UV-visible radiation.
ABSTRACT
There is currently a large effort to improve the performance of low cost renewable energy devices. Dye-sensitized solar cells (DSSCs) are emerging as one of the most promising low cost photovoltaic technologies, addressing "secure, clean and efficient solar energy conversion". Vegetable dyes, extracted from algae, flowers, fruit and leaves, can be used as sensitizers in DSSCs. Thus far, anthocyanin and betalain extracts together with selected chlorophyll derivatives are the most successful vegetable sensitizers. This review analyses recent progress in the exploitation of vegetable dyes for solar energy conversion and compares them to the properties of synthetic dyes. We provide an in-depth discussion on the main limitation of cell performance e.g. dye degradation, effective electron injection from the dye into the conduction band of semiconducting nanoparticles, such as titanium dioxide and zinc oxide, outlining future developments for the use of vegetable sensitizers in DSSCs. We also discuss the cost of vegetable dyes and how their versatility can boost the advancement of new power management solutions, especially for their integration in living environments, making the practical application of such systems economically viable. Finally, we present our view on future prospects in the development of synthetic analogues of vegetable dyes as sensitizers in DSSCs.
ABSTRACT
Dye-sensitized solar cells (DSSCs) based on Chlorine-e6 (Chl-e6), a Chlorophyll a derivative, and Chl-e6 containing Cu, have been investigated by carrying out incident photon to current efficiency (IPCE) and current-voltage (I-V) measurements. The effect of the metallic ion and the influence of the solvent polarity on the dye aggregation and their absorption bands have been analysed by performing electronic absorption measurements. The dependence of the photoelectrochemical parameters of these DSSCs on the electrolyte by the addition of pyrimidine and/or pyrrole has been discussed in details. For the first time I-V curves for a DSSC based on copper Chl-e6 dye have been shown and compared with Zn based chlorophyllin. Furthermore, the performance of a Cu-Chl-e6 based DSSC has been deeply improved by a progressive optimization of the TiO2 multilayer photoanode overcoming the best data reported in literature so far for this dye. It's worth to emphasize that, the analysis reported in this paper supplies very useful information which paves the way to further detailed studies turned to the employment of natural pigments as sensitizers for solar cells.
Subject(s)
Absorption, Physicochemical , Chlorophyllides/chemistry , Coloring Agents/chemistry , Photochemistry , Solar Energy , Electricity , Spectrum AnalysisABSTRACT
Sensitized P25 TiO2 was prepared by wet impregnation with a home-prepared perylene dye, i.e., N,N'-bis(2-(1-piperazino)ethyl)-3,4,9,10-perylene-tetracarboxylic acid diimide dichloride (PZPER). Energy levels of PZPER were found to be compatible with those of TiO2 allowing fast electron transfer. The obtained catalyst has been characterized and used in the gas-phase partial oxidation of aliphatic primary and secondary alcohols, i.e., methanol, ethanol, and 2-propanol. The reaction was carried out under cut-off (λ > 400 nm) simulated solar radiation in O2 atmosphere. The perylene derivative allowed a good absorbance of visible radiation thanks to its low optical energy gap (2.6 eV) which was evaluated by cyclic voltammetry. The optimal organic sensitizing amount was found to be 5.6 % w/w in terms of yield in carbonyl derivatives. Moreover, no change in reactivity/selectivity was observed after 10-h irradiation thus confirming the catalyst stability. Yields into formaldehyde, acetaldehyde, and acetone were 67, 70, and 96 %, respectively. No significant amounts of organic byproducts were detected but for methanol oxidation, whereas a minor amount of the substrate degraded to CO2.
Subject(s)
Imides/chemistry , Light , Methanol/chemistry , Perylene/analogs & derivatives , Titanium/chemistry , Catalysis , Chromatography, Gas , Electrons , Molecular Structure , Oxidation-Reduction , Perylene/chemistryABSTRACT
Chlorophylls based-dyes obtained from seaweeds represent attractive alternatives to the expensive and polluting pyridil based Ru complexes because of their abundance in nature. Another important characteristic is that the algae do not subtract either cropland or agricultural water, therefore do not conflict with agro-food sector. This pigment shows a typical intense absorption in the UV/blue (Soret band) and a less intense band in the red/near IR (Q band) spectral regions and for these reasons appear very promising as sensitizer dyes for DSSC. In the present study, we utilized chlorophylls from samples of the brown alga Undaria pinnatifida as sensitizer in DSSCs. The dye, extracted by frozen seaweeds and used without any chemical purification, showed a very good fill factor (0.69). Even the photelectrochemical parameters if compared with the existent literature are very interesting.
Subject(s)
Chlorophyll/chemistry , Coloring Agents/chemistry , Electrochemistry , Photochemistry , Seaweed/chemistry , Solar Energy , Ultraviolet Rays , Absorption , Spectrophotometry, Ultraviolet , Titanium/chemistryABSTRACT
Seven flavylium salt dyes were employed for the first time as sensitizers for dye-sensitized solar cells (DSSCs). The theoretical and experimental wavelengths of the maximum absorbances, the HOMO and LUMO energy levels, the coefficients, the oscillator strengths and the dipole moments are calculated for these synthetic dyes. The introduction of a donor group in the flavylium molecular structure was investigated. Photophysical and photoelectrochemical measurements showed that some of these synthetic analogues of anthocyanins are very promising for DSSC applications. The best performance was obtained by a DSSC based on the novel compound 7-(N,N-diethylamino)-3',4'-dihydroxyflavylium which produced a 2.15% solar energy-to-electricity conversion efficiency, under AM 1.5 irradiation (100 mW cm(-2)) with a short-circuit current density (J(sc)) of 12.0 mA cm(-2), a fill factor of 0.5 and an open-circuit voltage (V(oc)) of 0.355 V; its incident photocurrent efficiency of 51% at the peak of the visible absorption band of the dye is remarkable. Our results demonstrated that the substitution of a hydroxylic group with a diethylamine unit in position 7 of ring A of the flavylium backbone expanded the π-conjugation in the dye and thus resulted in a higher absorption in the visible region and is advantageous for effective electron injection from the dye into the conduction band of TiO2.
ABSTRACT
We explore the effect of re-radiation in surface-enhanced Raman scattering (SERS) through polarization-sensitive experiments on self-organized gold nanowires on which randomly oriented Methylene Blue molecules are adsorbed. We provide the exact laws ruling the polarized, unpolarized, and parallel- and cross-polarized SERS intensity as a function of the field polarizations. We show that SERS is polarized along the wire-to-wire nanocavity axis, independently from the excitation polarization. This proves the selective enhancement of the Raman dipole component parallel to the nanocavity at the single molecule level. Introducing a field enhancement tensor to account for the anisotropic polarization response of the nanowires, we work out a model that correctly predicts the experimental results for any excitation/detection polarization and goes beyond the E(4) approximation. We also show how polarization-sensitive SERS experiments permit one to evaluate independently the excitation and the re-radiation enhancement factors accessing the orientation-averaged non-diagonal components of the molecular Raman polarizability tensor.
Subject(s)
Gold/chemistry , Nanowires/chemistry , Radiation , Spectrum Analysis, Raman , Adsorption , Anisotropy , Models, Theoretical , Surface PropertiesABSTRACT
Brownian motion is a manifestation of the fluctuation-dissipation theorem of statistical mechanics. It regulates systems in physics, biology, chemistry, and finance. We use graphene as prototype material to unravel the consequences of the fluctuation-dissipation theorem in two dimensions, by studying the Brownian motion of optically trapped graphene flakes. These orient orthogonal to the light polarization, due to the optical constants anisotropy. We explain the flake dynamics in the optical trap and measure force and torque constants from the correlation functions of the tracking signals, as well as comparing experiments with a full electromagnetic theory of optical trapping. The understanding of optical trapping of two-dimensional nanostructures gained through our Brownian motion analysis paves the way to light-controlled manipulation and all-optical sorting of biological membranes and anisotropic macromolecules.