Post-lithiation: a way to control the ionic conductivity of solid-state thin film electrolyte.

Ionic conductivity is pivotal for solid-state battery performance. While the garnet oxide electrolyte Li7La3Zr2O12 (LLZO) boasts high ionic conductivity due to its distinct crystal structure and lithium-ion mobility, lithium loss during fabrication hampers its potential. In this study, we introduce a method that merges synthesis optimization with a post-lithiation process, enhancing LLZO's ionic conductivity. This approach compensates lithium loss with a gas-phase diffusion process, which stabilizes the cubic LLZO phase and amplifies its ionic conductivity by more than three orders of magnitude compared to electrolytes without post-lithiation. Through our comprehensive experimental procedure, we have conclusively determined that the film deposited at 700 °C and subsequently annealed at 700 °C with LiOH exhibits the highest conductivity, with a notable value of 1.11 × 10-2 S cm-1 at 200 °C. This is a significant boost compared to the as-deposited film (3.54 × 10-6 S cm-1 at 200 °C). Our findings present an additional approach to boosting lithium ion diffusion. The approach employed in this work has the potential to be applicable to films produced through other deposition methods, as it addresses the prevalent issue of lithium loss, a significant barrier to the utilization of lithium-rich thin films.

Neural correlates of central pain sensitization in chronic low back pain: a resting-state fMRI study.

PURPOSE: The objective of this study is to explore the neural correlates of pain sensitization in patients with chronic low back pain (cLBP). While the association between cLBP and pain sensitization has been widely reported, the underlying brain mechanism responsible for this relationship requires further investigation. METHODS: Our study included 56 cLBP patients and 56 healthy controls (HC). Functional magnetic resonance imaging data were obtained, and the voxel-wise amplitude of low-frequency fluctuation (ALFF) was calculated to identify brain alterations in cLBP patients compared to HC groups. Pearson correlation coefficients were computed to explore the association between clinical data and brain alterations. Furthermore, mediation analyses were performed to investigate the path association between brain alterations and pain-related behaviors. RESULTS: Our findings revealed that patients with cLBP exhibited higher sensitivity, attention, and catastrophizing tendencies towards pain compared to HC. Furthermore, cLBP patients displayed significantly higher ALFF in various brain regions within the "pain matrix" and the default mode network when compared to HC. The altered precuneus ALFF was positively correlated with pain intensity (R = 0.51, P<0.001) and was negatively correlated with pain sensitivity (R = -0.43, P<0.001) in cLBP patients. Importantly, the effect of altered precuneus ALFF on pain intensity was mediated by pain threshold in these patients. CONCLUSION: Our study suggests that altered neural activity in the precuneus may contribute to pain hypersensitivity, which further exacerbating pain in cLBP patients.

Facile synthesis of Ag nanoparticles-loaded chitosan antibacterial nanocomposite and its application in polypropylene.

The development of environmental-friendly antibacterial agents with high efficiency and low cost has become the focus of attention. In this work, the Ag nanoparticles doped into chitosan (Ag NPs-CS) were synthesized by a green and facile method, and the samples were characterized by UV-Vis spectroscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), and thermogravimetric analysis (TGA). The antibacterial tests implied that Ag NPs-CS obtained from glucose (G-Ag NPs-CS) exhibited the excellent antimicrobial activities against Gram-negative (Escherichia coli) and Gram-positive (Staphylococcus aureus) microbes. Besides, the utilization of antibacterial agents in polymeric materials plays an significant role in healthy living. The aim is to impart the antibacterial properties and maintain/improve the mechanical properties. Therefore, the G-Ag NPs-CS with 5 wt% Ag was chosen as the optimal additive to endow polypropylene with antimicrobial activity via a simple melt blending method. The results demonstrated that the suppression of bacteria proliferation was enhanced with increasing the amount of antibacterial agent, and the microorganisms were almost killed when the content reached to 8 wt%. Meanwhile, the considerable improvement in elastic modulus and impact strength along with a slight decrease of elongation at break provided the evidence that Ag NPs-CS/PP nanocomposites were the promising candidate for practical applications.