Intramedullary headless compression screw fixation of the middle phalanx: tips, tricks, and pitfalls.

This report emphasizes careful consideration of surgical technique for intramedullary screw fixation in middle phalanx fractures. Highlighting pitfalls, particularly with K-wire placement, it suggests the antegrade trans-articular approach as superior, urging further research for improved patient outcomes.

Comparison of time-efficiency of individually wrapped screws and sterile screw racks in distal radius fracture treatment.

INTRODUCTION: Time-efficiency of individually wrapped screws versus screws in a screw rack is not well established. MATERIALS AND METHODS: We performed a prospective single-center clinical study timing the interval between the surgeon asking and receiving a screw during plate and screw osteosynthesis of distal radius fractures. Patients were randomized for individually wrapped screws or screws in a screw rack. The study was conducted in a Level 1 Trauma Center and surgeries were performed between March and June 2023. RESULTS: Average handling time for screws from a screw rack was 9 s (SD 5.5; range 3-28) and 22 s for individually wrapped screws (SD 6.1; range 6-38). This average difference of 13 s is significant (p < 0.0001). CONCLUSION: There is a significant increase in handling time using individually wrapped screws over using a screw rack. LEVEL OF EVIDENCE: Level I (therapeutic, randomized controlled trial).

Polyethylene liner fracture in dual mobility trapeziometacarpal total joint replacement: how to make a timely diagnosis?

We present a case of fracture of the polyethylene liner of a dual-mobility trapeziometacarpal total joint arthroplasty. Standard radiographic imaging was normal. This case highlights the importance of dynamic radiographic imaging to make a timely diagnosis.

Does trapezium remodeling correlate with cup shape?

We investigated whether trapezium bone reaction was different following implantation of a trapeziometacarpal total joint replacement with a hemispheric or a conical cup. Fifty-three Keri Medical Touch implants with hemispheric cup and 53 with conical cup were prospectively followed up radiographically. We compared radiographs taken immediately and one year after surgery for cup subsidence, tilt, heterotopic ossification and loosening. Cup subsidence of at least 1 mm was detected in 4% of cases for both cup types. Additive bone reaction around the cup of more than 1 mm was present in 62% of conical cups and 47% of hemispheric cups. These were minor and there were no large ossifications with risk of impingement. Minor radiolucency was seen superficially at the implant-bone interface of 13% of the hemispheric cups and 9% of the conical cups. None of these bone reactions differed significantly according to cup design.

Radial tuberosity anatomy in intramedullar repair of distal biceps tendon ruptures. A radiological study.

The aim of this study was to measure cortex thickness and medullar canal width of the bicipital tuberosity, to evaluate the accessibility of a intramedullar fixation device and the resistance to pullout strengths of the anterior cortex. The final objective was to determine the length of tendon ingrowth size that will be expected when using this surgical technique. A total of 144 computer tomography images of the proximal radius were used. Bone thickness of the anterior and posterior cortex and medullar canal size were measured. The possible ingrowth of the tendon was measured both for an anatomical and non- anatomical reinsertion. Statistical and concordance analyses of results were performed. The average width of the medullar canal was 8,7mm proximal, 7,9mm distal and 7,7mm at the tuberosity. The average posterior and anterior cortex measured respectively 2,5mm and 2,9mm proximal, 3,2mm and 3,2mm distal and 2,8mm and 1,9mm at the radial tuberosity. The possible non-anatomical ingrowth was 7,6 mm on average and the possible anatomical ingrowth was 7,6mm on average. The radial tuberosity anatomy can accommodate the new distal biceps fixation device. The anterior cortex on which the new device relies for support has a similar thickness as the posterior cortex used in bicortical fixation devices which may suggest similar resistance to pull-out strengths. The availability for intra-osseous fixation of the tendon stump may avoids tendon gapping. The intra-osseous length for the tendon stump surpassed reported tendon slippage during mobilization and active contraction of the distal biceps tendon.

Total joint replacement for osteoarthritis of the carpometacarpal joint of the thumb: why and how?

Total joint replacement has certain advantages over other surgical treatment methods for osteoarthritis of the thumb carpometacarpal joint, including restoration of thumb length and alignment, good cosmetical result, fast recovery of hand function and prevention of iatrogenic complications at neighbouring joints. Disadvantages include the technical difficulty to perform this surgery and a possible higher complication rate. A meticulous surgical technique is mandatory. Combined with a cementless and modular ball-in-socket implant with a metal-on-polyethylene friction couple, a 10-year survival rate higher than 90% can be expected. Revision surgery is possible with implant exchange or conversion to trapeziectomy.

Anatomical intramedullary distal biceps tendon fixation. Our first experience.

Background: Intramedullary fixatiovn in distal biceps tendon repair has been proposed to address specific shortcomings of current fixation techniques. Previous studies described a nonanatomical repair. Hypothesis: The purpose of the present study is to report the short-term outcomes of an anatomic intramedullary fixation. Study Design: We evaluated functional and radiographic outcomes up to 6 months of follow-up. Methods: Patients with an acute distal biceps tendon rupture eligible for surgical repair were invited to take part in the study. Eleven patients were included in the final analysis. All patients were evaluated both clinically and radiographically at 2 weeks, 6 weeks, 3 months, and 6 months. Outcomes were recorded using the visual analog scale score for pain, the Mayo Elbow Performance Score, and Disabilities of the Arm, Shoulder, and Hand scores. The radiographic evaluation comprised X-ray and CT evaluation. Results: There were no failures of fixation in the patient group examined. Elbow mobility was symmetric for all patients from 6 months onward. Supination strength was similar uninjured side at final follow-up. Mean Disabilities of the Arm, Shoulder, and Hand score and Mayo Elbow Performance Score at final follow-up were 0 and 100, respectively. Computed tomography images showed no signs of button migration, cortical thinning due to button pressure or button breakout. The tendon could be followed to the button in all cases. One case of heterotopic ossification was seen. Conclusions: Anatomical intramedullary fixation of the DBT has excellent functional outcomes at 6 months. The anatomical repair resulted in a restoration of supination strength. This technique allows the anatomical reinsertion of the distal biceps tendon while minimizing the risk of PIN injury. The intraosseous position of the tendon avoids gap formation. No adverse reactions of the button on the bone were seen.

Evaluation of MRI Signal Changes of the Distal Biceps Tendon in Asymptomatic Patients.

PURPOSE: Magnetic resonance imaging (MRI) is used widely for complete ruptures of the distal biceps tendon. The validity of this investigation for bicipital bursitis and tendinosis is unknown. The purpose of present study was to assess the prevalence of incidental (asymptomatic) signal changes in the distal biceps tendon in patients who underwent MRI including the elbow. Our null hypothesis was that signal changes of the distal biceps tendon do not occur in asymptomatic patients. This would empower MRI as a diagnostic tool for bicipital bursitis and tendinosis as well as complete and partial distal biceps tendon ruptures. METHODS: We evaluated 1,191 elbow MRI scans including the distal biceps tendon insertion. The prevalence of incidental findings was calculated and sensitivity, specificity, positive predictive value, negative predictive value, false positive probability, and false negative probability were calculated. RESULTS: Signal changes of the distal biceps tendon or bursitis were identified in 8 of 1,191 asymptomatic patients (prevalence 0.6%). The sensitivity of MRI for distal biceps pathology was 97% (95% confidence interval [CI], 93%-99%), specificity 99% (95% CI, 98%-99%), positive predictive value 94% (95% CI, 89%-97%), negative predictive value 99% (95% CI, 99%-99%), false positive probability 6% (95% CI, 3%-10%), and false negative probability 0.3% (95% CI, 0.1%-0.9%). There was no correlation between explanatory variables, including age, sex, race, occupation, and inflammatory disease and incidental distal biceps tendon signal changes. CONCLUSIONS: The prevalence of distal biceps tendon signal changes on MRI in asymptomatic patients is very low. CLINICAL RELEVANCE: The negative predictive value of 99% shows that patients without signal changes on MRI may be assumed to have no distal biceps tendon pathology. MRI investigation of distal biceps tendon is a valuable tool in the diagnosis of tendinosis and bicipital bursitis.

Effect of Lidocaine 2% Versus Bupivacaine 0.5% and 1 Versus 2 Dual Separate Injections on Onset and Duration of Ultrasound-Guided Wrist Blocks: A Blinded 2 × 2 Factorial Randomized Clinical Trial.

BACKGROUND: Local anesthetics are often selected or mixed to accomplish faster onset of anesthesia. However, with ultrasound guidance, local anesthetics are delivered with greater precision, which may shorten the onset time with all classes of local anesthetics. In this study, we compared onset time and duration of ultrasound-guided wrist blocks with a fast onset versus a longer lasting local anesthetic administered via single or dual (spatially separate) injections at the level of the midforearm. METHODS: In this randomized clinical trial, 36 subjects scheduled for carpal tunnel release were randomly assigned to receive ultrasound-guided median and ulnar nerve blocks with lidocaine 2% or bupivacaine 0.5% via single or dual injections (n = 9 in each group). Subjects fulfilled the study requirements. The main outcome variables were onset and duration of sensory blockade, which were tested separately in 2 (drug) × 2 (injection) analysis of variances (ANOVAs) with interaction terms. RESULTS: Sensory block onset time did not differ significantly between subjects given lidocaine 2% (9.2 ± 3.4 minutes) or bupivacaine 0.5% (9.5 ± 3.1 minutes) (P = .76; mean difference, -0.3 ± 1.1 minutes [95% confidence interval {CI}, -2.5 to 1.9]) or between the single- (9.6 ± 2.8 minutes) and dual- (9.1 ± 3.6 minutes) injection groups (P = .69; mean difference, -0.4 ± 1.1 minutes [95% CI, -1.8 to 2.6]). Sensory duration was longer for subjects in the bupivacaine 0.5% group (27.3 ± 11.6 hours) than for subjects in the lidocaine 2% group (8.4 ± 4.1 hours) (P < .001; 95% CI, 12.7-25.1). However, sensory duration in the single- (15.7 ± 12.5 hours) and dual- (19.4 ± 13.1 hours) injection groups did not differ significantly (P = .28; mean difference, -3.7 ± 4.3 hours [95% CI, -12.6 to 5.1]). CONCLUSIONS: No significant effect was found for onset time between lidocaine 2% and bupivacaine 0.5% used in ultrasound-guided wrist blocks. Dual injections did not shorten onset time. Since mean nerve block duration was longer with bupivacaine 0.5%, our results suggest that the selection of local anesthetic for the median and ulnar nerves at the level of the midforearm should be based on the desired duration of the block and not on its speed of onset.

Reconstruction of flexor pollicis longus tendon with palmaris longus interposition graft: results in 14 patients.

The flexor pollicis longus tendon is prone to attritive rupture and retraction. Direct repair is often not possible. Interposition grafting is a treatment option to restore tendon continuity, although the surgical technique and postoperative results have not been well defined. We report our experience with this procedure. 14 patients were prospectively followed for a minimum of 10 months after surgery. There was one postoperative failure of the tendon reconstruction. Postoperative strength was comparable to the contralateral side, but thumb range of motion was significantly reduced. In general, patients reported excellent postoperative hand function. This procedure seems a viable treatment option with lower donor site morbidity than tendon transfer surgery.

Acute complete and partial distal biceps tendon ruptures: what have we learned? A review.

Acute distal biceps tendon (DBT) pathology includes bicipitoradial bursitis, tendinosis, partial and complete tears.Diagnosis of complete DBT tears is mainly clinical, whereas in partial tears medical imaging is a valuable addition to the clinical diagnosis.New insights in clinical and medical imaging of partial tears may reduce time to diagnosis and may guide the treatment plan.Most complete tears are best treated with primary repair using either a single-incision or double-incision approach with good clinical outcome.The double-incision technique has a higher risk of heterotopic ossification, whereas a single-incision technique carries a higher risk of nerve-related complications.Intramedullary fixation may be a viable solution to negate the risk of posterior interosseus nerve lesions in single-incision repairs.DBT endoscopy can be used to treat low-grade partial tears and tendinosis. Cite this article: EFORT Open Rev 2021;6:956-965. DOI: 10.1302/2058-5241.6.200145.

In vivo evaluation of a new intramedullary distal biceps tendon fixation device.

BACKGROUND: Intramedullary fixation in distal biceps tendon repair may be a solution to address specific shortcomings of current fixation techniques. Most investigations are limited to biomechanical evaluation. The purpose of this study was to report the short-term outcomes of an intramedullary fixation device. METHODS: We evaluated functional and radiographic outcomes at up to 6 months of follow-up. Patients with an acute distal biceps tendon rupture eligible for surgical repair were invited to take part in the study. Ten patients were included in the final analysis. All patients were evaluated both clinically and radiographically at 2 weeks, 6 weeks, 3 months, and 6 months. Outcomes were recorded using a visual analog scale score for pain, the Mayo Elbow Performance Score, and the Disabilities of the Arm, Shoulder and Hand score. Radiographic evaluation comprised radiographic and computed tomography evaluation. RESULTS: There were no failures of fixation in the patient group examined. Elbow mobility was symmetrical for all patients from 3 months onward. Supination strength was 86% of the uninjured side at final follow-up. The mean Disabilities of the Arm, Shoulder and Hand score and Mayo Elbow Performance Score at final follow-up were 0 and 100, respectively. Computed tomography images showed no signs of button migration, cortical thinning due to button pressure, or button breakout. The tendon could be followed to the button in all cases. CONCLUSIONS: The intramedullary fixation button technique to repair the distal biceps tendon has excellent functional outcomes at 6 months. No adverse reactions of the button on the bone were seen. As this technique minimizes the risk of posterior interosseous nerve injury and has a sufficient bone tunnel to avoid gap formation, this may be a promising new technique for distal biceps tendon rupture refixation.

In vitro Biomechanical Analysis of Proximal Phalangeal Osteotomy Fixation.

Background Corrective osteotomies of the proximal phalanx are typically stabilized with plate and screws. Although intramedullary headless screws form an alternative fixation method in the treatment of acute phalangeal fractures, reports about fixation of opening wedge corrective osteotomies with these implants are lacking. Objective The goal of the present study was to biomechanically compare the failure force of both fixation methods for this specific indication. Methods Twenty-four cadaver phalanges were equally distributed between apex volar and apex lateral opening wedge osteotomy groups. In each group, half of the osteotomies were fixed with a 1.3-mm dorsal locking plate, the other half with a 2.4-mm intramedullary headless screw. A three-point bending test was performed. Results The mean maximal failure force after apex lateral osteotomy was 178.4 N for the plate-screw construct and 144.0 N after intramedullary headless screw fixation. After apex volar osteotomy, mean maximal force was 237.6 N in the plate-screw group and 160.9 N in the intramedullary headless screw group. Mean stiffness after apex lateral osteotomy was 63.3 N/mm in the plate-screw group, and 55.9 N/mm in the intramedullary headless screw group. Mean stiffness after apex volar osteotomy was 197.5 N/mm and 60.0 N/mm for the plate-screw and intramedullary headless screw group, respectively. Conclusion For apex volar osteotomies, dorsally applied angular stable plate and screws provide significantly stronger fixation than intramedullary headless screws. For apex lateral osteotomies, fixation force is comparable. Clinical relevance These data are useful when considering fixation of opening wedge osteotomies with intramedullary screws.

Scaphoidectomy and 4-corner arthrodesis with headless compression screws: results, complications and their treatment.

Scaphoidectomy and 4-corner arthrodesis is a common salvage surgery for degenerative wrist pathology. The purpose of this study was to evaluate the results of this procedure performed with headless compression screws, with a special focus on postoperative complications and their treatment. We assessed 36 wrists in 31 patients that were treated between 2009 and 2017. Mean follow-up was 5.2 years (range 2.9- 9.4). Pain was expressed on a Visual Analog Scale. The Quick Disabilities of the Arm, Shoulder and hand (qDASH) questionnaire and Michigan Hand Outcome Questionnaire (MHOQ) were used to assess patient functionality and satisfaction. Range of motion and grip strength of both wrists were measured. Radiographs of the operated wrist were evaluated. Mean pain score was 1.5 ± 2.3 with 19% of patients being completely free of pain also during activity. Mean qDASH was 44 ± 20 and mean MHOQ was 10 ± 5. Mean flexion-extension arc of the operated wrist was 69° and 61% of the contralateral wrist. Mean grip strength was 35kg and 89% of the opposite wrist. Non-union was observed in two patients. Two patients required hardware removal and in three patients a pisiformectomy was performed. Conversion to total wrist arthrodesis was needed in one patient. We observed postoperative complications in 28% of our patients. Most complications can successfully be treated with additional surgery. The presence of pisotriquetral arthritis should be assessed before surgery and treated with pisiform excision.

Minimally Invasive Corrective Osteotomy for Metacarpal Malrotation.

Metacarpal fractures can be complicated by malrotation. This can cause functional problems with overriding or underriding of the fingers with flexion. Surgical treatment consists of corrective osteotomy and derotation. This is typically performed open and different techniques for osteotomy and fixation have been described. Postoperative complications include finger stiffness and hardware irritation. We propose a technique for minimally invasive corrective osteotomy of malunited metacarpal fractures with rotational malalignement. Advantages are quick rehabilitation and no prominent hardware.

A new intramedullary fixation method for distal biceps tendon ruptures: a biomechanical study.

BACKGROUND: Various techniques have been described for distal biceps tendon reinsertion. Although high success rates have been reported, all current techniques have specific shortcomings, with complications such as heterotopic ossification, nerve damage, and gap formation. The purpose of the present study was to biomechanically evaluate a new intramedullary fixation device that might reduce the risk of posterior interosseous nerve lesions. We therefore compared the fixation strength of this new intramedullary button with an extramedullary placed classic extracortical button. METHODS: A standard bicortical button was compared to the new intramedullary fixation device using fresh-frozen cadaveric specimens. The fixation strengths were tested both cyclically and statically. Load to failure and method of failure were also recorded. RESULTS: There were no failures during the cyclic load testing. The mean tendon-bone displacement was 0.87 ± 0.13 mm for the bicortical group and 0.83 ± 0.13 mm for the new button. During static loading, the mean load to failure for the bicortical group was 296 ± 97 N, whereas the new button group showed a higher mean load to failure of 356 ± 37 N. Breakout through the anterior cortex was recorded in 2 of 6 bicortically placed buttons and 1 of 6 in the new device. CONCLUSIONS: The new intramedullary fixation device yields comparable loads to failure compared with currently used techniques in a biomechanical setup. These findings together with the theoretical advantages suggest that this technique may be a valuable solution for the repair of distal biceps tendon rupture.

The effect of cup orientation on stability of trapeziometacarpal total joint arthroplasty: a biomechanical cadaver study.

It has been suggested that the cup of a trapeziometacarpal total joint replacement should be positioned parallel with the proximal articular surface of the trapezium to align it with the centre of motion. This would diminish the chance of dislocation. The goal of this study was to test this idea biomechanically. A linked trapeziometacarpal prosthesis was implanted in seven cadaver hands and combined with three-dimensional printed trapezium cups in 17 different orientations. For every combination, stability of the prosthesis was assessed through its entire passive range of motion. Dorsal inclination of the cup relative to the proximal articular surface increased the risk of dislocation with thumb flexion and opposition. The risk of dislocation was also increased with lateral or medial inclination of the cup exceeding 20°. Our results demonstrate that cup orientation is an important factor in prosthetic joint stability. Cup placement parallel to the proximal articular surface is ideal.