High energy dissipation-based process to improve the rheological properties of bentonite drilling muds by reducing the particle size.

Drilling mud is a multi-phase fluid that is used in the petroleum drilling process. Bentonite is the most important constituent of drilling mud; it endows the drilling mud with its rheological behaviors, such as viscosity, yield stress, and shear thinning. The process of manufacturing microscale bentonite at the nanoscale level is very promising for commercializing nano-based drilling mud. In contrast to the conventional method using the impeller, bentonite was manufactured in its nanoparticle state in the present work through ultrasonic and homogenizer processes in the solution state. In case of the ultrasonic process, the viscosity increase in the low shear rate region before and after processing of the 5 wt% bentonite-based mud and the rheological properties in the presence of polymer additive were compared. In case of the homogenizer process, the rheological properties of 3 wt% bentonite-based mud employed through the homogenizer process and 5 wt% mud prepared generally were compared. Both processes reported improvement of rheological properties, in which shear thinning behavior strongly occurred when particle size decreased through FE-SEM, TEM image analysis, and particle size analyzer. A regularized Herschel-Bulkley model suitable for rheological quantitative explanation of drilling mud including yield stress was selected. The homogenizer process has the potential to be applied in the petroleum drilling industry for large-scale production, and the mechanism was confirmed by numerical analyses. In conclusion, we presented a simple and easy-to-apply process to rapidly produce nano-based drilling mud.

Nitric Oxide-Releasing Bacterial Cellulose/Chitosan Crosslinked Hydrogels for the Treatment of Polymicrobial Wound Infections.

Polymicrobial wound infections are a major cause of infectious disease-related morbidity and mortality worldwide. In this study, we prepared a nitric oxide (NO)-releasing oxidized bacterial cellulose/chitosan (BCTO/CHI) crosslinked hydrogel to effectively treat polymicrobial wound infections. Linear polyethyleneimine diazeniumdiolate (PEI/NO) was used as the NO donor. The aldehyde group of BCTO and the amine of CHI were used as crosslinked hydrogel-based materials; their high NO loading capacity and antibacterial activity on the treatment of polymicrobial-infected wounds were investigated. The blank and NO-loaded crosslinked hydrogels, namely BCTO-CHI and BCTO-CHI-PEI/NO, were characterized according to their morphologies, chemical properties, and drug loading. BCTO-CHI-PEI/NO exhibited sustained drug release over four days. The high NO loading of BCTO-CHI-PEI/NO enhanced the bactericidal efficacy against multiple bacteria compared with BCTO-CHI. Furthermore, compared with blank hydrogels, BCTO-CHI-PEI/NO has a favorable rheological property due to the addition of a polymer-based NO donor. Moreover, BCTO-CHI-PEI/NO significantly accelerated wound healing and re-epithelialization in a mouse model of polymicrobial-infected wounds. We also found that both crosslinked hydrogels were nontoxic to healthy mammalian fibroblast cells. Therefore, our data suggest that the BCTO-CHI-PEI/NO developed in this study improves the efficacy of NO in the treatment of polymicrobial wound infections.

Influence of MoS2 Nanosheet Size on Performance of Drilling Mud.

Water-based drilling mud (WBM) is a non-Newtonian fluid that has a variety of applications such as in transporting cuttings during drilling, protecting the borehole, and cooling the drill bit. With the development of nano-technology, various nanoparticles have been synthesized and have been added to WBM to improve its performance. Shear thinning is the most important factor in drilling mud and this attribute can be improved when two-dimensional particles are added. MoS2 nanoparticles, which represent a typical two-dimensional material, are easy to synthesize in large quantities and have a high thermal conductivity and low coefficient of friction. Since the two-dimensional structure, thermal conductivity, and low coefficient of friction of MoS2 would improve the performance of WBM, we experimented with MoS2 nanosheets as an additive, under optimal conditions, using various samples each with uniform sizes and thicknesses of nanosheets. A large amount of MoS2 nanosheets was synthesized, sorted by thickness and diameter, and added to drilling mud. The diameter of MoS2 was divided into a small diameter group (about 100⁻400 nm) and a big diameter group (about 300⁻650 nm), and the thickness was divided into 1⁻2 nm and 5⁻10 nm groups. Experimental results showed that when MoS2 is added to WBM, shear thinning occurs more strongly. In addition, the addition of MoS2 with a thickness of 1⁻2 nm and a diameter of 300⁻650 nm resulted in the highest increase in viscosity and thermal conductivity of WBM. As a result, we experimentally confirmed that MoS2 can be used as an additive to increase the thermal conductivity and viscosity of WBM and to make shear thinning phenomenon more.

Data on the anisotropic interfacial slip length over fibrous porous media.

To characterize the velocity slip at the fibrous porous media, data on the anisotropic slip length has been fully analyzed through direct simulations for various geometrical aspects of fiber architecture [2] ). This data article provides detailed slip lengths and slip coefficients in dimensionless form as a function of various geometrical parameters of fibrous porous media including the fiber volume fraction, the dimensionless void length and the normalized permeability. The data is presented for three different fiber packing structures (the quadrilateral, hexagonal and compressed hexagonal packing) in both the fiber and normal to fiber directions. Finally a set of curves from the complete fitted equation set are also provided in a single figure that can be used to estimate the slip length and the normalized permeability for a given fibrous porous media.

Microfluidic assessment of mechanical cell damage by extensional stress.

Mammalian cells have been widely used in bioreactors to produce biological products such as pharmaceutical materials. The productivity of such bioreactors is vastly affected by flow-induced cell damage in complicated flow environments, such as agitation-driven turbulence and oxygen bubble bursting at the interface between the culturing medium and air. However, there is no systematic approach to diagnose the cell damage caused by the hydrodynamic stress. In this work, we propose a novel microfluidic method to accurately assess the mechanical cell damage under a controlled extensional stress field, generated in a microfluidic cross-slot geometry. The cell damage in the extensional field is related to the oxygen bubble bursting process. We employed viscoelasticity-induced particle focusing to align the cells along the shear-free channel centerline, so that all the cells experience a similar extensional stress field, which also precludes the cell damage due to wall shear stress. We applied our novel microfluidic sensor to find the critical extensional stress to damage Chinese hamster ovary (CHO) cells; the critical stress is found to be ∼250 Pa. Our current results are relevant in the design of practical bioreactors, as our results clearly demonstrate that the control of the bubble bursting process is critical in minimizing cell damage in bioreactor applications. Further, our results will provide useful information on the biophysical cell properties under fluid flow environments.

PDMS-based turbulent microfluidic mixer.

Over the past decade, homogeneous mixing in microfluidic devices has been a critical challenge, because of the inherently low flow rates in microfluidic channels. Although several mixer designs have been suggested to achieve efficient mixing, most of them involve intricate structures requiring a series of laborious fabrication processes. Operation at high flow rates can greatly enhance mixing by induction of turbulence, but devices that can resist such a high pressure drop to induce turbulence in microfluidic channels are difficult to fabricate, especially for commonly used poly(dimethylsiloxane) (PDMS)-based microfluidic devices. We have developed a Y-shaped, turbulent microfluidic mixer made of PDMS and a glass substrate by strong bonding of the substrates to a nanoadhesive layer deposited via initiated chemical vapor deposition. The high bonding strength of the nanoadhesive layer enables safe operation of the PDMS/glass turbulent microfluidic mixer at a total water flow rate of 40 mL min(-1), corresponding to a Reynolds number, Re, of ~4423, one of the highest values achieved in a microfluidic channel. The turbulence generated as a result of the high Re allows rapid mixing of the input fluids on contact. Image analysis showed that mixing started as soon as the fluids were introduced into the mixer. The experimental results matched the numerical predictions well, demonstrating that convective mixing was dominant as a result of turbulence induced in the microfluidic channel. Using the turbulent microfluidic mixer, we have demonstrated high throughput formation of emulsions with narrower size distribution. It was shown that as the flow rate increases inside the microfluidic channel, the size distribution of resulting emulsions decreases owing to the increase in the turbulent energy dissipation. The turbulent microfluidic mixer developed in this work not only enables rapid mixing of streams, but also increases throughputs of microfluidic reactors.