ABSTRACT
Thermoelectric textile devices represent an intriguing avenue for powering wearable electronics. The lack of air-stable n-type polymers has, until now, prevented the development of n-type multifilament yarns, which are needed for textile manufacturing. Here, the thermomechanical properties of the recently reported n-type polymer poly(benzodifurandione) (PBFDO) are explored and its suitability as a yarn coating material is assessed. The outstanding robustness of the polymer facilitates the coating of silk yarn that, as a result, displays an effective bulk conductivity of 13 S cm-1, with a projected half-life of 3.2 ± 0.7 years at ambient conditions. Moreover, the n-type PBFDO coated silk yarn with a Young's modulus of E = 0.6 GPa and a strain at break of εbreak = 14% can be machine washed, with only a threefold decrease in conductivity after seven washing cycles. PBFDO and poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) coated silk yarns are used to fabricate two out-of-plane thermoelectric textile devices: a thermoelectric button and a larger thermopile with 16 legs. Excellent air stability is paired with an open-circuit voltage of 17 mV and a maximum output power of 0.67 µW for a temperature difference of 70 K. Evidently, PBFDO coated multifilament silk yarn is a promising component for the realization of air stable thermoelectric textile devices.
ABSTRACT
Through direct arylation polymerization, a series of mixed ion-electron conducting polymers with a low synthetic complexity index is synthesized. A thieno[3,2-b]thiophene monomer with oligoether side chains is used in direct arylation polymerization together with a wide range of aryl bromides with varying electronic character from electron-donating thiophene to electron-accepting benzothiadiazole. The obtained polymers are less synthetically complex than other mixed ion-electron conducting polymers due to higher yield, fewer synthetic steps and less toxic reagents. Organic electrochemical transistors (OECTs) based on a newly synthesized copolymer comprising thieno[3,2-b]thiophene with oligoether side chains and bithiophene exhibit excellent device performance. A high charge-carrier mobility of up to µ = 1.8 cm2 V-1 s-1 was observed, obtained by dividing the figure of merit [µC*] from OECT measurements by the volumetric capacitance C* from electrochemical impedance spectroscopy, which reached a value of more than 215 F cm-3.
ABSTRACT
Excessive nutrient supply in agricultural regions has led to various environmental issues, thereby requiring concentrated management owing to its persistent upward trend. Nutrient budgets (NBs), a vital agricultural environmental indicator, are employed for nutrient management in agricultural areas, using data surveyed by administrative agencies. However, the spatial extent of nutrient data for nutrient budgeting is limited by administrative boundaries according to the surveying organization, posing challenges in interpreting spatial patterns at the watershed level. In this study, a novel approach was developed to identify priority nutrient management areas by applying hot spot spatial analysis to watershed-level NBs, considering hydrological characteristics. This method was applied to approximately 850 subwatersheds across the Republic of Korea, where land cover characteristics are complex. Reassessing nutrient budgets at the watershed scale, accounting for overlapping administrative boundary areas and crop cultivation ratios, indicated similar levels between the two methods. Hot spot analysis revealed that watersheds with elevated NBs mirrored the spatial patterns of livestock excreta and cropland. The spatial distribution characteristics of watersheds with high nutrient levels in rivers corresponded with the concentration characteristics of industrial and commercial areas. Therefore, applying watershed-level NBs based on land cover ratios that consider nutrient input characteristics in agricultural regions is deemed appropriate for selecting priority nutrient management areas. Collectively, this study presents a method for selecting nutrient management priority areas by simultaneously considering the spatial characteristics of various environmental factors, such as land cover, livestock excreta, river water quality, and land area-based watershed-specific NBs. The proposed approach, considering mixed land cover characteristics, is anticipated to be valuable for selecting priority management areas in watersheds with diverse pollution sources. Future research is needed to explore nutrient budgets within watersheds, the influence of land use on pollution sources, and their correlation with water quality.
Subject(s)
Environmental Monitoring , Water Quality , Environmental Monitoring/methods , Agriculture , Rivers , NutrientsABSTRACT
Dengue virus is an enveloped virus with an icosahedral assembly of envelope proteins (E). The E proteins are arranged as a head-to-tail homodimer, and domain III (EDIII) is placed at the edge of the dimer, converging to a pentamer interface. For a structure-based approach, cholera toxin B (CTB) was harnessed as a structural scaffold for the five-fold symmetry of EDIII. Pivoted by an RNA-mediated chaperone for the protein folding and assembly, CTB-EDIII of dengue serotype 1 (DV1) was successfully produced as soluble pentamers in an E. coli host with a high yield of about 28 mg/L. Immunization of mice with CTB-DV1EDIII elicited increased levels of neutralizing antibodies against infectious viruses compared to the control group immunized with DV1EDIII without CTB fusion. IgG isotype switching into a balanced Th1/Th2 response was also observed, probably triggered by the intrinsic adjuvant activity of CTB. Confirming the immune-enhancing potential of CTB in stabilizing the pentamer assembly of EDIII, this study introduces a low-cost bacterial production platform designed to augment the soluble production of subunit vaccine candidates, particularly those targeting flaviviruses.
ABSTRACT
OBJECTIVES: This study aimed to investigate the association between multimorbidity, which refers to the presence of two or more chronic diseases, and periodontal disease in Korean adults using national survey data. METHODS: A total of 12,440 Korean adults aged ≥19 years were selected from the seventh Korea National Health and Nutrition Examination Survey (KNHANES). We investigated periodontal disease status based on various variables, including the gender, age, educational level, income level, smoking and alcohol drinking status, frequency of daily toothbrushing, and unmet dental treatment needs. Furthermore, periodontal status according to diagnosed chronic diseases, including hypertension, dyslipidaemia, stroke, myocardial infarction, angina pectoris, and diabetes, was investigated, and the association between multimorbidity and periodontal disease was analysed through multiple logistic regression using SAS 9.4. RESULTS: According to the general characteristics of the study participants, the prevalence of periodontal disease was higher in males, smokers, older age, and lower educational and income levels (p < 0.001). Moreover, as the frequency of daily toothbrushing increased, the distribution of periodontal disease decreased (p < 0.001). The prevalence of periodontal disease was higher in those with chronic diseases than in those without chronic diseases and was statistically significantly higher as the number of diagnosed chronic diseases increased (p < 0.001). Additionally, an increase in the number of chronic diseases was observed to increase the prevalence and risk of periodontal disease. CONCLUSION: These results suggest that multimorbidity significantly affects the prevalence of periodontal disease.
Subject(s)
Multimorbidity , Periodontal Diseases , Adult , Male , Humans , Cross-Sectional Studies , Nutrition Surveys , Periodontal Diseases/epidemiology , Chronic Disease , Republic of Korea/epidemiology , Cohort Studies , PrevalenceABSTRACT
Conjugated polymers exhibit a unique portfolio of electrical and electrochemical behavior, which - paired with the mechanical properties that are typical for macromolecules - make them intriguing candidates for a wide range of application areas from wearable electronics to bioelectronics. However, the degree of oxidation or reduction of the polymer can strongly impact the mechanical response and thus must be considered when designing flexible or stretchable devices. This tutorial review first explores how the chain architecture, processing as well as the resulting nano- and microstructure impact the rheological and mechanical properties. In addition, different methods for the mechanical characterization of thin films and bulk materials such as fibers are summarized. Then, the review discusses how chemical and electrochemical doping alter the mechanical properties in terms of stiffness and ductility. Finally, the mechanical response of (doped) conjugated polymers is discussed in the context of (1) organic photovoltaics, representing thin-film devices with a relatively low charge-carrier density, (2) organic thermoelectrics, where chemical doping is used to realize thin films or bulk materials with a high doping level, and (3) organic electrochemical transistors, where electrochemical doping allows high charge-carrier densities to be reached, albeit accompanied by significant swelling. In the future, chemical and electrochemical doping may not only allow modulation and optimization of the electrical and electrochemical behavior of conjugated polymers, but also facilitate the design of materials with a tunable mechanical response.
ABSTRACT
BACKGROUND: Continuous exposure of the skin to ultraviolet B (UVB) rays can cause inflammation and photodamage. In previous studies, we observed that the upregulation of nc886, a noncoding RNA (ncRNA), can alleviate UVB-induced inflammation through suppression of the protein kinase RNA (PKR) pathway. We aim to investigate the effect of fermented black ginseng extract (FBGE), which has been shown to increase the expression of nc886, on UVB-induced inflammation in keratinocytes. METHODS: To confirm the cytotoxicity of FBGE, MTT assay was performed, and no significant cytotoxicity was found on human keratinocytes. The efficacies of FBGE were assessed through qPCR, Western blotting, and ELISA analysis which confirmed regulation of UVB-induced inflammation. RESULTS: The analysis results showed that FBGE inhibited the decrease in nc886 expression and the increase in the methylated nc886 caused by UVB. It also prevented the UVB-induced increase of metalloproteinase-9 (MMP-9), metalloproteinase-1 (MMP-1), cyclooxygenase-2 (COX-2), prostaglandin E2 (PGE2), interleukin-8 (IL-8) and tumor necrosis factor-α (TNF-α). Additionally, FBGE suppressed the PKR-MAPK pathways activated by UVB. CONCLUSION: These results implicate that FBGE can alleviate UVB-induced inflammation through regulation of the nc886-PKR pathway.
Subject(s)
Keratinocytes , Panax , Humans , Keratinocytes/metabolism , Skin , Inflammation/metabolism , Metalloproteases/metabolism , Metalloproteases/pharmacology , Ultraviolet Rays/adverse effectsABSTRACT
Photonic crystals with mechanochromic properties are currently under intensive study to provide intuitive colorimetric detection of strains for various applications. However, the sensitivity of color change to strain is intrinsically limited, as the degree of deformation determines the wavelength shift. To overcome this limitation, auxetic photonic patterns that exhibit ultra-sensitive mechanochromism are designed. These patterns have a regular arrangement of cuts that expand to accommodate the strain, while the skeletal framework undergoes torsional deformation. Elastic photonic crystals composed of a non-close-packed array of colloidal particles are embedded in the cut area of the auxetic patterns. As the cut area amplifies the strains, the elastic photonic crystals show significant color change even for small total strains. The degree of local-strain amplification, or sensitivity of color change, is controllable by adjusting the width of cuts in the auxetic framework. In this work, a maximum sensitivity of up to 60 nm/% is achieved, which is 20 times higher than bulk films. It is believed that the auxetic photonic patterns with ultra-sensitive mechanochromism will provide new opportunities for the pragmatic use of mechanochromic materials in various fields, including structural health monitoring.
ABSTRACT
In this study, accelerated chloride diffusion tests are performed on ordinary Portland cement (OPC), ground granulated blast furnace slag (GGBFS), and fly ash (FA) concretes aged 4-6 years. Passed charge is evaluated according to ASTM-C-1202 for 12 mixtures, considering water-binder (W/B) ratios (0.37, 0.42, and 0.47), GGBFS replacement rates (0%, 30%, 50%), and FA replacement rates (0% and 30%). The effects of aged days on passed charge reduction behavior are quantified through repetitive regression analysis. Among existing machine learning (ML) models, linear, lasso, and ridge models are used to analyze the correlation of aged days and mix properties with passed charge. Passed charge analysis considering long-term age shows a significant variability decrease of passed charge by W/B ratio with increasing age and added admixtures (GGBFS and FA). Furthermore, the higher the water-binder ratio in GGBFS and FA concretes, the greater the decrease in passed charge due to aged days. The ML model-based regression analysis shows high correlation when compressive strength and independent variables are considered together. Future work includes a correlational analysis between mixture properties and chloride ingress durability performance using deep learning models based on the time series properties of evaluation data.
ABSTRACT
Quantum computing promises to offer substantial speed-ups over its classical counterpart for certain problems. However, the greatest impediment to realizing its full potential is noise that is inherent to these systems. The widely accepted solution to this challenge is the implementation of fault-tolerant quantum circuits, which is out of reach for current processors. Here we report experiments on a noisy 127-qubit processor and demonstrate the measurement of accurate expectation values for circuit volumes at a scale beyond brute-force classical computation. We argue that this represents evidence for the utility of quantum computing in a pre-fault-tolerant era. These experimental results are enabled by advances in the coherence and calibration of a superconducting processor at this scale and the ability to characterize1 and controllably manipulate noise across such a large device. We establish the accuracy of the measured expectation values by comparing them with the output of exactly verifiable circuits. In the regime of strong entanglement, the quantum computer provides correct results for which leading classical approximations such as pure-state-based 1D (matrix product states, MPS) and 2D (isometric tensor network states, isoTNS) tensor network methods2,3 break down. These experiments demonstrate a foundational tool for the realization of near-term quantum applications4,5.
ABSTRACT
Conjugated polymers with oligoether side chains are promising mixed ionic-electronic conductors, but they tend to feature a low glass transition temperature and hence a low elastic modulus, which prevents their use if mechanical robust materials are required. Carboxymethylated cellulose nanofibrils (CNF) are found to be a suitable reinforcing agent for a soft polythiophene with tetraethylene glycol side chains. Dry nanocomposites feature a Young's modulus of more than 400 MPa, which reversibly decreases to 10 MPa or less upon passive swelling through water uptake. The presence of CNF results in a slight decrease in electronic mobility but enhances the ionic mobility and volumetric capacitance, with the latter increasing from 164 to 197 F cm-3 upon the addition of 20 vol % CNF. Overall, organic electrochemical transistors (OECTs) feature a higher switching speed and a transconductance that is independent of the CNF content up to at least 20 vol % CNF. Hence, CNF-reinforced conjugated polymers with oligoether side chains facilitate the design of mechanically adaptive mixed ionic-electronic conductors for wearable electronics and bioelectronics.
ABSTRACT
Quantum error correction offers a promising path for performing high fidelity quantum computations. Although fully fault-tolerant executions of algorithms remain unrealized, recent improvements in control electronics and quantum hardware enable increasingly advanced demonstrations of the necessary operations for error correction. Here, we perform quantum error correction on superconducting qubits connected in a heavy-hexagon lattice. We encode a logical qubit with distance three and perform several rounds of fault-tolerant syndrome measurements that allow for the correction of any single fault in the circuitry. Using real-time feedback, we reset syndrome and flag qubits conditionally after each syndrome extraction cycle. We report decoder dependent logical error, with average logical error per syndrome measurement in Z(X)-basis of ~0.040 (~0.088) and ~0.037 (~0.087) for matching and maximum likelihood decoders, respectively, on leakage post-selected data.
ABSTRACT
Cu(II) ions are one of the essential mineral elements in the human body, but can pose a substantial health risk to people exposed to high concentrations of Cu(II) ions over a long period. Therefore, the ability to detect Cu(II) ions in drinking water is important. In this study, a novel colorimetric sensing probe for the easy and onsite detection of Cu(II) ions in drinking water was developed. The probe was constructed through selective chemical etching of triangular Ag nanoplates with tunable localized surface plasmon resonance (LSPR) properties. Ethylenediamine (EDA) was used as an organic capping agent to improve the chemical stability of triangular Ag nanoplates. Selective chemical etching of the EDA-capped Ag nanoplates in the presence of Cu(II) ions as a result of the formation of a coordination complex between the EDA and Cu(II) ions caused remarkable changes in the nanoplates' LSPR characteristics. On the basis of this phenomenon, a novel colorimetric sensing probe capable of detecting Cu(II) ions in drinking water at concentrations above the safety limit was developed. Our findings were also extended to develop a portable and paper-based sensing probe with good long-term stability to overcome the shortcomings of liquid-phase colorimetric sensors without requiring a spectrometer. The proposed colorimetric sensing probes provide accurate results even with a real sample and offer numerous advantages over conventional sensing platforms, including clearly distinguishable color changes that can be observed by the naked eye; thus, the proposed probes can be used for the selective, reliable, and low-cost point-of-care detection of Cu(II) ions in water.
ABSTRACT
BACKGROUND: This aim of this study was to develop an objective tool for rating submental fat applied to Koreans. METHODS: The study was conducted between April 2019 and October 2019. A total of 92 subjects were enrolled in the study. Clinical photos of the subjects were categorized using validated CR-SMFRS by three plastic surgeons and one dermatologist. The categorized photos were then shown to six different plastic surgeons for evaluation. RESULTS: The Cohen's kappa value for the six raters were 0.830, 0.742, 0.703, 0.907, 0.862, and 0.793 with statistical significance (p < 0.001). ICC value was between 0.860 and 0.966 (p < 0.001). Since the Cohen's value and ICC were above 0.6 for all raters, the ratings performed by all six raters were used in the analysis. The ICC values between raters were between 0.899 and 0.902. CONCLUSIONS: We came up with a set of reference photos that can be used for submental fat rating scale applicable to Korean subjects. LEVEL OF EVIDENCE: II.
ABSTRACT
For the colloidal nanophotonic structures, a transmission electron microscope (TEM) grid has been widely used as a substrate of dark-field microscopy because a nanometer-scale feature can be effectively determined by TEM imaging following dark-field microscopic studies. However, an optically lossy carbon layer has been implemented in conventional TEM grids. A broadband scattering from the edges of the TEM grid further restricted an accessible signal-to-noise ratio. Herein, we demonstrate that the freely suspended, ultrathin, and wide-scale transparent nanomembrane can address such challenges. We developed a 1 mm by 600 µm scale and 20 nm thick poly(vinyl formal) nanomembrane, whose area is around 180 times wider than a conventional TEM grid, so that the possible broadband scattering at the edges of the grid was effectively excluded. Also, such nanomembranes can be formed without the assistance of carbon support; allowing us to achieve the highest signal-to-background ratio of scattering among other substrates.
ABSTRACT
A mechanochromic strain sensor that is capable of distinguishing the orientation, the location, and the degree of deformation based on the highly stretchable membrane of main-chain chiral liquid crystalline elastomer (MCLCE) is proposed. The MCLCE film is designed to exhibit uniform and significant color shift upon the small strain by using step-growth polymerization of liquid crystal (LC) oligomer and its phase-stabilization in solvent mesogen. As conformally placed on the bottom elastomer sheet, the MCLCE film shows multimodal, instantaneous color change for sensing arbitrary in-plane deformation, out-of-plane bending, and nonzero Gaussian deformation. Based on high freedom in the device design, it is also demonstrated that this sensor can display color patterns or encrypted images in response to the localized weight or strain. The simple and straightforward concept proposed here can be applicable in the fields of wearable devices, displays, and soft robotics.
ABSTRACT
Senescent fibroblasts progressively deteriorate the functional properties of skin tissue. Senescent cells secrete senescence-associated secretory phenotype (SASP) factor, which causes the aging of surrounding non-senescent cells and accelerates aging in the individuals. Recent findings suggested the senomorphic targeting of the SASP regulation as a new generation of effective therapeutics. We investigated whether Isatis tinctoria L. leaf extract (ITE) inhibited senescence biomarkers p53, p21CDKN1A, and p16INK4A gene expression, and SASP secretions by inhibiting cellular senescence in the replicative senescent human dermal fibroblast (RS-HDF). ITE has been demonstrated to inhibit the secretion of SASP factors in several senomorphic types by regulating the MAPK/NF-κB pathway via its inhibitory effect on mTOR. ITE suppressed the inflammatory response by inhibiting mTOR, MAPK, and IκBα phosphorylation, and blocking the nuclear translocation of NF-κB. In addition, we observed that autophagy pathway was related to inhibitory effect of ITE on cellular senescence. From these results, we concluded that ITE can prevent and restore senescence by blocking the activation and secretion of senescence-related factors generated from RS-HDFs through mTOR-NF-κB regulation.
Subject(s)
Isatis , NF-kappa B , Cellular Senescence , Fibroblasts , Isatis/metabolism , NF-kappa B/metabolism , Plant Extracts/metabolism , Plant Extracts/pharmacology , Senotherapeutics , TOR Serine-Threonine Kinases/metabolismABSTRACT
In this work, a facile synthetic route for the preparation of high aspect ratio Cu oxide nanowires is reported. The preparation of the Cu oxide nanowires begins with the generation of pure Cu nanoparticles by inert gas condensation (IGC) method, follows by dispersing the obtained nanoparticles in methanol with the aid of ultrasonication. The mixture is stored at different temperature for the transformation from Cu nanoparticle to Cu oxide nanowires. The influences of the kind of solution, the ratio of methanol to Cu nanoparticle, dispersion time and temperature towards the generation of Cu oxide nanowires are studied in detail. Scanning electron microscopy studies indicate that high aspect ratio Cu oxide nanowires with diameter of a few tens of nanometers and length up to several tens of micrometers could be obtained under proper conditions. The mechanism for the transformation of Cu nanoparticles to Cu oxide nanowires is also investigated.
ABSTRACT
Arbitrarily long quantum computations require quantum memories that can be repeatedly measured without being corrupted. Here, we preserve the state of a quantum memory, notably with the additional use of flagged error events. All error events were extracted using fast, midcircuit measurements and resets of the physical qubits. Among the error decoders we considered, we introduce a perfect matching decoder that was calibrated from measurements containing up to size-four correlated events. To compare the decoders, we used a partial postselection scheme shown to retain ten times more data than full postselection. We observed logical errors per round of 2.2±0.1×10^{-2} (decoded without postselection) and 5.1±0.7×10^{-4} (full postselection), which was less than the physical measurement error of 7×10^{-3} and therefore surpasses a pseudothreshold for repeated logical measurements.