Antimicrobial Potential of Chitosan Films Incorporated with Alcoholic Extract from Mimosa tenuiflora Leaves.

Antimicrobial films were prepared with chitosan containing the methanolic extract of M. tenuiflora leaves (FECT20%, FECT30%, and FECT40%), and their antimicrobial activities were evaluated by agar diffusion. The films were characterized by IR spectroscopy, scanning electron microscopy (SEM) and TG/DTG curves. TG/DTG curves showed thermal stability of chitosan-extract films up to 166 ºC. Micrographs of chitosan-extract films revealed an increase in porosity with the addition of extract. The FECT40% film showed inhibition zone diameters (IZ) against Micrococcus luteus, Staphylococcus aureus, Bacillus subtilis, and B. cereus, ranging from 1.0 ± 0.02 to 0.72 ± 0.09 cm. Only FECT30% and FECT40% inhibited the P. aeruginosa with IZs of 0.68 ± 0.02 and 0.77 ± 0.06 cm, respectively. In turn, the extract showed inhibition against B. subtilis and B. cereus, with IZs values of 0.92 ± 0.2 cm and 0.72 ± 0.05 cm, respectively. Additionally, the crude extract presented antioxidant potential with inhibition percentages of 32.74% ± 0.90 for ABTS and 27.04% ± 1.36 for DPPH. The antimicrobial and antioxidant activities of the crude extract, as well as the antimicrobial property of chitosan-extract films, suggests the potential of these biopolymers for the development of wound healing bandages and new food packaging alternatives.

Lightweight carbon foam obtained from post-use polyethylene terephthalate bottles, properties, and potential applications.

The excessive consumption of plastic packaging, especially those produced with polyethylene terephthalate (PET), and the fact that most of them are destined for garbage have made such packaging a worrying environmental liability. Their inadequate disposal promotes the pollution of soils, watercourses, and oceans, and even the presence of component materials of these packages in the human body, in the form of microplastics, has been observed. As research in the area advances, greater concerns arise, as more problems arising from the excessive use and disposal of plastics are identified. Looking for an alternative for the destination of this material, a technology was developed for the production of materials with characteristics similar to 3D graphene. This carbon material has qualities and versatility that allow its wide use in several applications and is produced using PET as a carbon precursor. This work presents this production technology with possible variables, the characterization of the produced materials, and their potential applications. For the electronics area, such as supercapacitors, improvement points needed for validation were observed. For application as an adsorbent and use in the treatment of industrial effluents when using sand covered by carbon material, the results demonstrated efficiency. The material proved to be a potential destination for PET, as an alternative to reduce this environmental liability.

Layer-by-layer assembled films of multi-walled carbon nanotubes with chitosan and cellulose nanocrystals.

Chitosan solutions and cellulose nanocrystal suspensions were used to produce highly stable aqueous dispersions of multi-walled carbon nanotubes (MWCNTs). The different MWCNT dispersions, presenting positive and negative charges, were used to prepare multilayered hybrid thin films through electrostatic layer-by-layer (LBL) self-assembly. The MWCNTs are well dispersed and homogeneously distributed on each layer of chitosan and cellulose nanocrystals of the films. The nanotubes are densely packed in each multilayer, forming a random network. The surface of the LBL film exhibited a uniform and relatively smooth surface with a mean roughness value of ∼5.8±0.4nm. Electrochemical characterization revealed a decrease in two orders of magnitude in the film resistance as the number of bilayers increased from 5 to 20, which is a consequence of an increase in the amount of conductive material (MWCNT). The thin films with up to 20 bilayers exhibited transmittance higher than 90% in the visible range. The results presented in this work demonstrate the viability of the LBL technique for the deposition of active materials using the biopolymer pair chitosan/cellulose nanocrystals. The obtained films can be employed for the design of transparent and biocompatible carbon nanostructured based electrodes.