ABSTRACT
Relaxor ferroelectric (RFE) films are promising energy-storage candidates for miniaturizing high-power electronic systems, which is credited to their high energy density (Ue) and efficiency. However, advancing their Ue beyond 200 joules per cubic centimeter is challenging, limiting their potential for next-generation energy-storage devices. We implemented a partitioning polar-slush strategy in RFEs to push the boundary of Ue. Guided by phase-field simulations, we designed and fabricated high-performance Bi(Mg0.5Ti0.5)O3-SrTiO3-based RFE films with isolated slush-like polar clusters, which were realized through suppression of the nonpolar cubic matrix and introduction of highly insulating networks. The simultaneous enhancement of the reversible polarization and breakdown strength leads to a Ue of 202 joules per cubic centimeter with a high efficiency of ~79%. The proposed strategy provides a design freedom for next-generation high-performance dielectrics.
ABSTRACT
GeTe is a promising p-type material with increasingly enhanced thermoelectric properties reported in recent years, demonstrating its superiority for mid-temperature applications. In this work, the thermoelectric performance of GeTe is improved by a facile composite approach. We find that incorporating a small amount of boron particles into the Bi-doped GeTe leads to significant enhancement in power factor and simultaneous reduction in thermal conductivity, through which the synergistic modulation of electrical and thermal transport properties is realized. The thermal mismatch between the boron particles and the matrix induces high-density dislocations that effectively scatter the mid-frequency phonons, accounting for a minimum lattice thermal conductivity of 0.43 Wm-1K-1 at 613 K. Furthermore, the presence of boron/GeTe interfaces modifies the interfacial potential barriers, resulting in increased Seebeck coefficient and hence enhanced power factor (25.4 µWcm-1K-2 at 300 K). Consequently, we obtain a maximum figure of merit Zmax of 4.0 × 10-3 K-1 at 613 K in the GeTe-based composites, which is the record-high value in GeTe-based thermoelectric materials and also superior to most of thermoelectric systems for mid-temperature applications. This work provides an effective way to further enhance the performance of GeTe-based thermoelectrics.
ABSTRACT
Recently, the earth-abundant tin sulfide (SnS) has emerged as a promising thermoelectric material due to its phonon and electron structure similar to that of tin selenide (SnSe). However, compared with SnSe, limited progress has been achieved in the thermoelectric property enhancement of SnS. Textured SnS polycrystals with an enhanced thermoelectric performance have been developed in this work. The high carrier mobility benefited from the enhanced texture through the repressing strategy of spark plasma sintering, improving the electrical conductivity. In addition, Sn atom deficiencies in the texture sample led to an increased hole concentration, further boosting the electrical conductivity and power factor. The power factor exceeded 4.10 µW/cm·K2 at 423 K and 5.50 µW/cm·K2 at 850 K. The phonon scattering was strengthened by adjusting the multiscale microstructures including dislocations, defect clusters, etc., leading to an ultralow lattice thermal conductivity of 0.23 W/m·K at 850 K. A figure of merit zT > 1.3 at 850 K and an average zTave of 0.58 in the temperature range 373-850 K were achieved in the SnS polycrystal.
ABSTRACT
GeSe, an analogue of SnSe, shows promise in exhibiting exceptional thermoelectric performance in the Pnma phase. The constraints on its dopability, however, pose challenges in attaining optimal carrier concentrations and improving ZT values. This study demonstrates a crystal structure evolution strategy for achieving highly doped samples and promising ZTs in GeSe via LiBiTe2 alloying. A rhombohedral phase (R3m) can be stabilized in the GeSe-LiBiTe2 system, further evolving into a cubic (Fm3Ì m) phase with a rising temperature. The band structures of GeSe-LiBiTe2 in the rhombohedral and cubic phases feature a similar multiple-valley energy-converged valence band of L and Σ bands. The observed high carrier concentration (â¼1020 cm-3) reflects the effective convergence of these bands, enabling a high density-of-states effective mass and an enhanced power factor. Moreover, a very low lattice thermal conductivity of 0.6-0.5 W m-1 K-1 from 300 to 723 K is achieved in 0.9GeSe-0.1LiBiTe2, approaching the amorphous limit value. This remarkably low lattice thermal conductivity is related to phonon scattering from point defects, planar vacancies, and ferroelectric instability-induced low-energy Einstein oscillators. Finally, a maximum ZT value of 1.1 to 1.3 at 723 K is obtained, with a high average ZT value of over 0.8 (400-723 K) in 0.9GeSe-0.1LiBiTe2 samples. This study establishes a viable route for tailoring crystal structures to significantly improve the performance of GeSe-related compounds.
ABSTRACT
Nanoscale spatially controlled modulation of the properties of ferroelectrics via artificial domain pattering is crucial to their emerging optoelectronics applications. New patterning strategies to achieve high precision and efficiency and to link the resultant domain structures with device functionalities are being sought. Here, we present an epitaxial heterostructure of SrRuO3/PbTiO3/SrRuO3, wherein the domain configuration is delicately determined by the charge screening conditions in the SrRuO3 layer and the substrate strains. Chemical etching of the top SrRuO3 layer leads to a transition from in-plane a domains to out-of-plane c domains, accompanied by a giant (>105) modification in the second harmonic generation response. The modulation effect, coupled with the plasmonic resonance effect from SrRuO3, enables a highly flexible design of nonlinear optical devices, as demonstrated by a simulated split-ring resonator metasurface. This domain patterning strategy may be extended to more thin-film ferroelectric systems with domain stabilities amenable to electrostatic boundary conditions.
ABSTRACT
The liquid-like feature of thermoelectric superionic conductors is a double-edged sword: the long-range migration of ions hinders the phonon transport, but their directional segregation greatly impairs the service stability. We report the synergetic enhancement in figure of merit (ZT) and stability in Cu1.99Se-based superionic conductors enabled by ion confinement effects. Guided by density functional theory and nudged elastic band simulations, we elevated the activation energy to restrict ion migrations through a cation-anion co-doping strategy. We reduced the carrier concentration without sacrificing the low thermal conductivity, obtaining a ZT of â¼3.0 at 1,050 K. Notably, the fabricated device module maintained a high conversion efficiency of up to â¼13.4% for a temperature difference of 518 K without obvious degradation after 120 cycles. Our work could be generalized to develop electrically and thermally robust functional materials with ionic migration characteristics.
ABSTRACT
Thermoelectric materials are highly promising for waste heat harvesting. Although thermoelectric materials research has expanded over the years, bismuth telluride-based alloys are still the best for near-room-temperature applications. In this work, a ≈38% enhancement of the average ZT (300-473 K) to 1.21 is achieved by mixing Bi0.4Sb1.6Te3 with an emerging thermoelectric material Sb2Si2Te6, which is significantly higher than that of most BiySb2-yTe3-based composites. This enhancement is facilitated by the unique interface region between the Bi0.4Sb1.6Te3 matrix and Sb2Si2Te6-based precipitates with an orderly atomic arrangement, which promotes the transport of charge carriers with minimal scattering, overcoming a common factor that is limiting ZT enhancement in such composites. At the same time, high-density dislocations in the same region can effectively scatter the phonons, decoupling the electron-phonon transport. This results in a ≈56% enhancement of the thermoelectric quality factor at 373 K, from 0.41 for the pristine sample to 0.64 for the composite sample. A single-leg device is fabricated with a high efficiency of 5.4% at ΔT = 164 K further demonstrating the efficacy of the Sb2Si2Te6 compositing strategy and the importance of the precipitate-matrix interface microstructure in improving the performance of materials for relatively low-temperature applications.
ABSTRACT
Electric field-induced second harmonic generation allows electrically controlling nonlinear light-matter interactions crucial for emerging integrated photonics applications. Despite its wide presence in materials, the figures-of-merit of electric field-induced second harmonic generation are yet to be elevated to enable novel device functionalities. Here, we show that the polar skyrmions, a topological phase spontaneously formed in PbTiO3/SrTiO3 ferroelectric superlattices, exhibit a high comprehensive electric field-induced second harmonic generation performance. The second-order nonlinear susceptibility and modulation depth, measured under non-resonant 800 nm excitation, reach ~54.2 pm V-1 and ~664% V-1, respectively, and high response bandwidth (higher than 10 MHz), wide operating temperature range (up to ~400 K) and good fatigue resistance (>1010 cycles) are also demonstrated. Through combined in-situ experiments and phase-field simulations, we establish the microscopic links between the exotic polarization configuration and field-induced transition paths of the skyrmions and their electric field-induced second harmonic generation response. Our study not only presents a highly competitive thin-film material ready for constructing on-chip devices, but opens up new avenues of utilizing topological polar structures in the fields of photonics and optoelectronics.
ABSTRACT
Black phosphorus with a superior theoretical capacity (2596 mAh g-1) and high conductivity is regarded as one of the powerful candidates for lithium-ion battery (LIB) anode materials, whereas the severe volume expansion and sluggish kinetics still impede its applications in LIBs. By contrast, the exfoliated two-dimensional phosphorene owns negligible volume variation, and its intrinsic piezoelectricity is considered to be beneficial to the Li-ion transfer kinetics, while its positive influence has not been discussed yet. Herein, a phosphorene/MXene heterostructure-textured nanopiezocomposite is proposed with even phosphorene distribution and enhanced piezo-electrochemical coupling as an applicable free-standing asymmetric membrane electrode beyond the skin effect for enhanced Li-ion storage. The experimental and simulation analysis reveals that the embedded phosphorene nanosheets not only provide abundant active sites for Li-ions, but also endow the nanocomposite with favorable piezoelectricity, thus promoting the Li-ion transfer kinetics by generating the piezoelectric field serving as an extra accelerator. By waltzing with the MXene framework, the optimized electrode exhibits enhanced kinetics and stability, achieving stable cycling performances for 1,000 cycles at 2 A g-1, and delivering a high reversible capacity of 524 mAh g-1 at - 20 â, indicating the positive influence of the structural merits of self-assembled nanopiezocomposites on promoting stability and kinetics.
ABSTRACT
Mg3(Sb,Bi)2 is a promising thermoelectric material suited for electronic cooling, but there is still room to optimize its low-temperature performance. This work realizes >200% enhancement in room-temperature zT by incorporating metallic inclusions (Nb or Ta) into the Mg3(Sb,Bi)2-based matrix. The electrical conductivity is boosted in the range of 300-450 K, whereas the corresponding Seebeck coefficients remain unchanged, leading to an exceptionally high room-temperature power factor >30 µW cm-1 K-2; such an unusual effect originates mainly from the modified interfacial barriers. The reduced interfacial barriers are conducive to carrier transport at low and high temperatures. Furthermore, benefiting from the reduced lattice thermal conductivity, a record-high average zT > 1.5 and a maximum zT of 2.04 at 798 K are achieved, resulting in a high thermoelectric conversion efficiency of 15%. This work demonstrates an efficient nanocomposite strategy to enhance the wide-temperature-range thermoelectric performance of n-type Mg3(Sb,Bi)2, broadening their potential for practical applications.
ABSTRACT
Thermoelectric sulfide materials are of particular interest due to the earth-abundant and cost-effective nature of sulfur. Here, we report a new n-type degenerate semiconductor sulfide, AgBiPbS3, which adopts a Fm3Ì m structure with a narrow band gap of â¼0.32 eV. Despite the homogeneous distribution of elements at the scale of micrometer, Ag2S nanoprecipitates with dimensions of several nanometers were detected throughout the matrix. AgBiPbS3 exhibits a low room-temperature lattice thermal conductivity of 0.88 W m-1 K-1, owing to the intrinsic low lattice thermal conductivity of Ag2S and the effective scattering of phonons at nanoprecipitate boundaries. Moreover, compared to AgBiS2, AgBiPbS3 demonstrates a significantly improved weighted mobility of >16 cm2 V-1 s-1 at 300 K, leading to an enhanced PF of 1.6 µW cm-1 K-2 at 300 K. The superior electrical transport in AgBiPbS3 can be attributed to the high valley degeneracy of the L point (the conduction band minimum), which is contributed by the Pb s and Pb p orbitals. Further, Ga doping is found to be effective in modulating the Fermi levels of AgBiPbS3, leading to further enhancement of PF with a PFave of 2.7 µW cm-1 K-2 in the temperature range of 300-823 K. Consequently, a relatively high ZTave of 0.22 and a peak ZT of â¼0.4 at 823 K have been achieved in 3% Ga-doped AgBiPbS3, highlighting the potential of AgBiPbS3 as an n-type thermoelectric sulfide.
ABSTRACT
Mg3 (Sb,Bi)2 is a potential nearly-room temperature thermoelectric compound composed of earth-abundant elements. However, complex defect tuning and exceptional microstructural control are required. Prior studies have confirmed the detrimental effect of Mg vacancies (VMg ) in Mg3 (Sb,Bi)2 . This study proposes an approach to mitigating the negative scattering effect of VMg by Bi deficiency, synergistically modulating the electrical and thermal transport properties to enhance the thermoelectric performance. Positron annihilation spectrometry and Cs -corrected scanning transmission electron microscopy analyses indicated that the VMg tends to coalesce due to the introduced Bi vacancies (VBi ). The defects created by Bi deficiency effectively weaken the scattering of electrons from the intrinsic VMg and enhance phonon scattering. A peak zT of 1.82 at 773 K and high conversion efficiency of 11.3% at ∆T = 473 K are achieved in the optimized composition of Mg3 (Sb,Bi)2 by tuning the defect combination. This work demonstrates a feasible and effective approach to improving the performance of Mg3 (Sb,Bi)2 as an emerging thermoelectric material.
ABSTRACT
Direct neutron detection based on semiconductor crystals holds promise to transform current neutron detector technologies and further boosts their widespread applications. It is, however, long impeded by the dearth of suitable materials in the form of sizeable bulk crystals. Here, high-quality centimeter-sized LiInP2 Se6 single crystals are developed using the Bridgman method and their structure and property characteristics are systematically investigated. The prototype detectors fabricated from the crystals demonstrate an energy resolution of 53.7% in response to α-particles generated from an 241 Am source and robust, well-defined response spectra to thermal neutrons that exhibit no polarization or degradation effects under prolonged neutron/γ-ray irradiation. The primary mechanisms of Se-vacancy and InLi antisite defects in the carrier trapping process are also identified. Such insights are critical for further enhancing the energy resolution of LiInP2 Se6 bulk crystals toward the intrinsic level (≈8.6% as indicated by the chemical vapor transport-grown thin crystals). These results pave the way for practically adopting LiInP2 Se6 single crystals in new-generation solid-state neutron detectors.
ABSTRACT
Dielectric capacitors with high energy storage performance are highly desired for next-generation advanced high/pulsed power capacitors that demand miniaturization and integration. However, the poor energy-storage density that results from the low breakdown strength, has been the major challenge for practical applications of dielectric capacitors. Herein, we propose a heterovalent-doping-enabled atom-displacement fluctuation strategy for the design of low-atom-displacements regions in the antiferroelectric matrix to achieve the increase in breakdown strength and enhancement of the energy-storage density for AgNbO3-based multilayer capacitors. An ultrahigh breakdown strength ~1450 kV·cm-1 is realized in the Sm0.05Ag0.85Nb0.7Ta0.3O3 multilayer capacitors, especially with an ultrahigh Urec ~14 J·cm-3, excellent η ~ 85% and PD,max ~ 102.84 MW·cm-3, manifesting a breakthrough in the comprehensive energy storage performance for lead-free antiferroelectric capacitors. This work offers a good paradigm for improving the energy storage properties of antiferroelectric multilayer capacitors to meet the demanding requirements of advanced energy storage applications.
ABSTRACT
Antiferroelectrics (AFEs) are promising candidates in energy-storage capacitors, electrocaloric solid-cooling, and displacement transducers. As an actively studied lead-free antiferroelectric (AFE) material, NaNbO3 has long suffered from its ferroelectric (FE)-like polarization-electric field (P-E) hysteresis loops with high remnant polarization and large hysteresis. Guided by theoretical calculations, a new strategy of reducing the oxygen octahedral tilting angle is proposed to stabilize the AFE P phase (Space group Pbma) of NaNbO3. To validate this, we judiciously introduced CaHfO3 with a low Goldschmidt tolerance factor and AgNbO3 with a low electronegativity difference into NaNbO3, the decreased cation displacements and [BO6] octahedral tilting angles were confirmed by Synchrotron X-ray powder diffraction and aberration-corrected scanning transmission electron microscopy. Of particular importance is that the 0.75NaNbO3-0.20AgNbO3-0.05CaHfO3 ceramic exhibits highly reversible phase transition between the AFE and FE states, showing well-defined double P-E loops and sprout-shaped strain-electric field curves with reduced hysteresis, low remnant polarization, high AFE-FE phase transition field, and zero negative strain. Our work provides a new strategy for designing NaNbO3-based AFE material with well-defined double P-E loops, which can also be extended to discover a variety of new lead-free AFEs.
ABSTRACT
GeMnTe2 adopts a cubic rock salt structure and is a promising mid-temperature thermoelectric material. The pair distribution function analysis of neutron total scattering data, however, indicates that GeMnTe2 is locally distorted from the ideal rock salt structure with Ge2+ cations being discordant and displaced â¼0.3 Å off the octahedron center. By alloying GeMnTe2 with SbTe, the carrier concentration can be tuned in GeMnTe2-x%SbTe (x = 15.1), leading to converged multiple broad valence bands and a high Seebeck coefficient of >200 µV K-1 from 300 to 823 K. The system exhibits a large density-of-state effective mass of >10 me and a high weighted mobility of 80 cm2 V-1 s-1, leading to a power factor of 15 µWcm-1 K-2 at 823 K. The composition GeMnTe2-15.1%SbTe exhibits very low lattice thermal conductivity of â¼0.5 Wm-1 K-1 at 823 K, attributed to the combination of off-centering cations in the rock salt structure, Ge/Mn positional disorder, dislocations, and abundant Ge-rich and Mn-rich nanoparticles. A ZT value of â¼1.5 can be achieved for GeMnTe2-15.1%SbTe with a ZTave of 0.96 in the temperature range of 400-823 K.
ABSTRACT
Transition metal dichalcogenides (TMDs) are regarded as promising cathode materials for zinc-ion storage owing to their large interlayer spacings. However, their capabilities are still limited by sluggish kinetics and inferior conductivities. In this study, a facile one-pot solvothermal method is exploited to vertically plant piezoelectric 1T MoSe2 nanoflowers on carbon cloth (CC) to fabricate crystallographically textured electrodes. The self-built-in electric field owing to the intrinsic piezoelectricity during the intercalation/deintercalation processes can serve as an additional piezo-electrochemical coupling accelerator to enhance the migration of Zn2+ . Moreover, the expanded interlayer distance (9-10 Å), overall high hydrophilicity, and conductivity of the 1T phase MoSe2 also promoted the kinetics. These advantages endow the tailored 1T MoSe2 /CC nanopiezocomposite with feasible Zn2+ diffusion and desirable electrochemical performances at room and low temperatures. Moreover, 1T MoSe2 /CC-based quasi-solid-state zinc-ion batteries are constructed to evaluate the potential of the proposed material in low-temperature flexible energy storage devices. This work expounds the positive effect of intrinsic piezoelectricity of TMDs on Zn2+ migration and further explores the availabilities of TMDs in low-temperature wearable energy-storage devices.
ABSTRACT
Recent advances in perovskite ferroelectrics have fostered a host of exciting sensors and actuators. Defect engineering provides critical control of the performance of ferroelectric materials, especially lead-free ones. However, it remains a challenge to quantitatively study the concentration of defects due to the complexity of measurement techniques. Here, a feasible approach to analyzing the A-site defect and electron in alkali metal niobate is demonstrated. The theoretical relationships among defect concentration, conductivity, and oxygen partial pressure can be established based on the defect chemistry equilibria. The type and concentration of defects are reflected through the conductivity variation with oxygen partial pressure. As a result, the variation of defect concentration gives rise to defect-driven interfacial polarization, which further leads to distinct properties of the ceramics. e.g., abnormal dielectric behavior. Furthermore, this study also suggests a strategy to manipulate defects and charges in perovskite oxides for performance optimization.
ABSTRACT
Aberrant activation of receptor tyrosine kinase (RTK) is usually a result of mutation and plays important roles in tumorigenesis. How RTK without mutation affects tumorigenesis remains incompletely understood. Here we show that in human melanomas pro-prion (pro-PrP) is an adaptor protein for an E3 ligase c-Cbl, enabling it to polyubiquitinate activated insulin-like growth factor-1 receptor (IGF-1R), leading to enhanced melanoma metastasis. All human melanoma cell lines studied here express pro-PrP, retaining its glycosylphosphatidylinositol-peptide signal sequence (GPI-PSS). The sequence, PVILLISFLI in the GPI-PSS of pro-PrP, binds c-Cbl, docking c-Cbl to the inner cell membrane, forming a pro-PrP/c-Cbl/IGF-1R trimeric complex. Subsequently, IGF-1R polyubiquitination and degradation are augmented, which increases autophagy and tumor metastasis. Importantly, the synthetic peptide PVILLISFLI disrupts the pro-PrP/c-Cbl/IGF-1R complex, reducing cancer cell autophagy and mitigating tumor aggressiveness in vitro and in vivo. Targeting cancer-associated GPI-PSS may provide a therapeutic approach for treating human cancers expressing pro-PrP.
Subject(s)
Melanoma , Prions , Humans , Ubiquitin-Protein Ligases/metabolism , Membrane Proteins/metabolism , Prions/metabolism , Cell Line, Tumor , Melanoma/pathology , Ubiquitination , Adaptor Proteins, Signal Transducing/metabolism , Carcinogenesis , Proto-Oncogene Proteins c-cbl/genetics , Proto-Oncogene Proteins c-cbl/metabolismABSTRACT
Tunable devices constructed by ferroelectric thin films are often desired to possess a low dielectric loss while maintainging a high dielectric tunability over a broad operating temperature range in applications, for example, resonators, filters, or phase shifters. However, it is difficult to simultaneously achieve these characteristics by traditional strategies, such as doping and strain modifying. Here, we demonstrate that the dielectric tunability of the sol-gel-prepared Pb(Sc1/2Nb1/2)0.9(Mg1/3Nb2/3)0.1O3 (PSNMN) thin film can be almost doubled from ~47% to ~80.0% (at 10 kHz) at a low electric field (~530 kV/cm), and the dielectric loss can be sharply reduced by more than an order of magnitude, from ~0.50 to ~0.037 (at 1 kHz) when the thin film was annealed in air at 650°C for 15 h under the help of an atmosphere-compensating-block (ACB) made from the proto-PSNMN gel. Moreover, the PSNMN thin film annealed with ACB also exhibited an extremely high thermally-stable dielectric tunability in an ultrabroad temperature range (>130 K), which could be attributed to the Maxwell-Wagner (MW) effect generated by the interface between the PSNMN disordered matrix and the B-site nanoscale-ordered structure formed during the long-term annealing process. The reduced dielectric loss is mainly benefited from the reduced concentration of oxygen vacancy and the possible MW effects, and the enhanced dielectric tunability could be ascribed to the weaker domain-pinning effect by oxygen vacancy. The breakthrough provides a new universal strategy to achieve utrahigh tunable performance in A(B'1/2B"1/2)O3 ferroelectric thin films with a B-site nanoscale-ordered structure, meanwhile it paves the way for ultraintergrated tunable thin-film-devices with great phase shifter performance in practical applications.