Solid-state sodium ion conductors are crucial for the next generation of all-solid-state sodium batteries with high capacity, low cost, and improved safety. Sodium closo-carbadodecaborate (NaCB11 H12 ) is an attractive Na-ion conductor owing to its high thermal, electrochemical, and interfacial stability. Mechanical milling has recently been shown to increase conductivity by five orders of magnitude at room temperature, making it appealing for application in all-solid-state sodium batteries. Intriguingly, milling longer than 2 h led to a significant decrease in conductivity. In this study, X-ray Raman scattering (XRS) spectroscopy is used to probe the origin of the anomalous impact of mechanical treatment on the ionic conductivity of NaCB11 H12 . The B, C, and Na K-edge XRS spectra are successfully measured for the first time, and ab initio calculations are employed to interpret the results. The experimental and computational results reveal that the decrease in ionic conductivity upon prolonged milling is due to the increased proximity of Na to the CB11 H12 cage, caused by severe distortion of the long-range structure. Overall, this work demonstrates how the XRS technique, allowing investigation of low Z elements such as C and B in the bulk, can be used to acquire valuable information on the electronic structure of solid electrolytes and battery materials in general.
Thermal polymorphism in the alkali-metal salts incorporating the icosohedral monocarba-hydridoborate anion, CB11H12-, results in intriguing dynamical properties leading to superionic conductivity for the lightest alkali-metal analogues, LiCB11H12 and NaCB11H12. As such, these two have been the focus of most recent CB11H12- related studies, with less attention paid to the heavier alkali-metal salts, such as CsCB11H12. Nonetheless, it is of fundamental importance to compare the nature of the structural arrangements and interactions across the entire alkali-metal series. Thermal polymorphism in CsCB11H12 was investigated using a combination of techniques: X-ray powder diffraction; differential scanning calorimetry; Raman, infrared, and neutron spectroscopies; and ab initio calculations. The unexpected temperature-dependent structural behavior of anhydrous CsCB11H12 can be potentially justified assuming the existence of two polymorphs with similar free energies at room temperature: (i) a previously reported, ordered R3 polymorph stabilized upon drying and transforming first to R3c symmetry near 313 K and then to a similarly packed but disordered I43d polymorph near 353 K and (ii) a disordered Fm3 polymorph that initially appears from the disordered I43d polymorph near 513 K along with another disordered high-temperature P63mc polymorph. Quasielastic neutron scattering results indicate that the CB11H12- anions in the disordered phase at 560 K are undergoing isotropic rotational diffusion, with a jump correlation frequency [1.19(9) × 1011 s-1] in line with those for the lighter-metal analogues.
The crystal structures of three thermal polymorphs (I, II, and III) for each isomer of closo-dicarbadodecaboranes C2B10H12 (ortho, meta, and para) have been determined by combining synchrotron radiation X-ray powder diffraction and density functional theory calculations. The structures are in agreement with previous calorimetric and spectroscopic studies. The difference between rotatory phases (plastic crystals) I and II lies in isotropic rotations in the former and anisotropic rotations of the icosahedral clusters in the latter. Phase I is the cubic close packing (ccp) of rotating closo-molecules C2B10H12 in the space group Fm3Ì . Phase II is the ccp of rotating closo-molecules C2B10H12 in the cubic space group Pa3Ì . The preferred rotational axis in II varies with the isomer. The ordered phases III are orthorhombic (meta) or monoclinic (ortho and para) deformations of the cubic unit cell of the disordered phases I and II. The ordering in the phase III of the ortho-isomer carrying the biggest electrical dipole moment creates a twofold superstructure w.r.t. the cubic unit cell. The thermal polymorphism for C2B10H12 and related metal salts can be explained by division of the cohesive intercluster interactions into two categories (i) dispersive cohesive interaction with additional Coulombic components in the metal salts and (ii) anisotropic local interaction resulting from nonuniform charge distribution around icosahedral clusters. The local interactions are averaged out by thermally activated cluster dynamics (rotations and rotational jumps) which effectively increase the symmetry of the cluster. The C2B10H12 molecules resist at least as well as the CB11H12- anion to the oxidation, and both clusters form easily a mixed compound. This allows designing solid electrolytes such as Nax(CB11H12)x(C2B10H12)1-x, where the cation content may be varied and the temperature of transition into the disordered conducting phase is decreased.
The body-centered cubic (bcc) polymorph of NaCB11H12 has been stabilized at room temperature by high-energy mechanical milling. Temperature-dependent electrochemical impedance spectroscopy shows an optimum at 45-min milling time, leading to an rt conductivity of 4 mS cm-1. Mechanical milling suppresses an order-disorder phase transition in the investigated temperature range. Nevertheless, two main regimes can be identified, with two clearly distinct activation energies. Powder X-ray diffraction and 23Na solid-state NMR reveal two different Na+ environments, which are partially occupied, in the bcc polymorph. The increased number of available sodium sites w.r.t. ccp polymorph raises the configurational entropy of the bcc phase, contributing to a higher ionic conductivity. Mechanical treatment does not alter the oxidative stability of NaCB11H12. Electrochemical test on a symmetric cell (Na|NaCB11H12|Na) without control of the stack pressure provides a critical current density of 0.12 mA cm-2, able to fully charge/discharge a 120 mA h g-1 specific capacity positive electrode at the rate of C/2.
LiBH4 has been widely studied as a solid-state electrolyte in Li-ion batteries working at 120 °C due to the low ionic conductivity at room temperature. In this work, by mixing with MgO, the Li-ion conductivity of LiBH4 has been improved. The optimum composition of the mixture is 53 v/v % of MgO, showing a Li-ion conductivity of 2.86 × 10-4 S cm-1 at 20 °C. The formation of the composite does not affect the electrochemical stability window, which is similar to that of pure LiBH4 (about 2.2 V vs Li+/Li). The mixture has been incorporated as the electrolyte in a TiS2/Li all-solid-state Li-ion battery. A test at room temperature showed that only five cycles already resulted in cell failure. On the other hand, it was possible to form a stable solid electrolyte interphase by applying several charge/discharge cycles at 60 °C. Afterward, the battery worked at room temperature for up to 30 cycles with a capacity retention of about 80%.
BACKGROUND: Innovative technologies and informatics offer a wide range of services to health districts, doctors, nurses, and patients, and is changing the traditional concept of health care. In the last few years, the availability of portable devices, their easiness to transport and use, and the capability to collect and transmit various clinical data have resulted in the fast development of telemedicine. However, despite its potential impact in improving patient conditions, and its cost effectiveness reported in literature, telemedicine is not in daily practice. OBJECTIVE: The aim of this study is to provide evidence of the positive impact of telemonitoring proving the sustainability of an application by sending spirometry outcomes from patients' homes to the hospital doctors via the Internet, and from doctors to patients by an additional phone call solution. METHODS: We examined collected data related to clinical improvement of patients with cystic fibrosis (CF). The patients were followed-up at home using telemonitoring for a period of 10 years, with the aims to prove the sustainability of the methodology (transmissions of spirometry from the patients' home to the doctors and feedback from the doctors to the patients by phone call from the hospital). We stored and analyzed all spirometry transmissions received, and tested the possible presence to decrease the costs between the standard clinical trial (only ambulatory visits) and standard clinical trial with telemonitoring for the follow-up of patients with CF (telemedicine). This was done through an economic analysis of the costs for patients followed at home by telemonitoring. We assessed four years of observation and a simulation of total long-term costs between 2010 and 2020. RESULTS: We discovered a potential saving of 40,397.00 per patient for 10 years, actualized at 36,802.97 for the follow-up of all patients enrolled. CONCLUSIONS: The results from the study suggest that telemedicine can improve the health of patients with CF. It is a relatively cheap and potentially sustainable solution, compared to standard clinical trials. However, to establish and prove the long-term effectiveness and cost-effectiveness, more controlled psychological and behavioral studies are needed.
BACKGROUND: Obesity is one of the biggest drivers of preventable chronic diseases and healthcare costs in Worldwide. Different prevention activities are suggested. By monitoring daily energy expenditure (EE) could be possible make personalized diets and programming physical activity. In this, physical inactivity is one of the most important public health problems. Some studies refer the effort of the international community in promoting physical activities. Physical activity can be promoted only by increasing citizens' empowerment on taking care of their health, and it passes from the improving of individual information. Technology can offer solutions and metrics for monitoring and measuring daily activity by interacting with individuals, sharing information and feedbacks. OBJECTIVE: In this study we review indicators of total energy expenditure and weaknesses of available devices in assessing these parameters. METHODS: Literature review and technology testing EuNetHta core model. RESULTS: For the clinical aspects, it is fundamental to take into account all the factor that can influence the personal energy expenditure as: heart rate, blood pressure and thermoregulation (influenced by the body temperature). DISCUSSION: In this study we focused the attention on the importance of tools to encourage the physical activity. We made an analysis of the factor that can influence the right analysis of energy expenditure and at the same time the energy regime. A punctual monitoring of the exercise regime could be helpful in Telemedicine application as Telemonitorig. More study are needed to value the impact of physical activity tracker in Telemonitorig protocols. CONCLUSION: On the assessment of the energy expenditure, critical issues are related to the physiological data acquisition. Sensors connected with mobile devices could be important tools for disease prevention and interventions affecting health behaviors. New devices applications are potential useful for telemedicine assistance, but security of data and the related communication protocol limits should be taking into account.
Energy Metabolism/physiology , Exercise/physiology , Monitoring, Ambulatory/instrumentation , Telemedicine/instrumentation , Blood Pressure , Body Temperature Regulation , Health Behavior , Heart Rate , Humans , Hypothalamus/metabolism
