ABSTRACT
Biomass waste and wastewater are important wastes in the process of industrialization, which need to be effectively treated and utilized. In this work, an innovative method of collaborative treatment of biomass waste and phenol-containing wastewater is proposed. Biomass waste was used to produce activated carbon (AC), and then AC was used for phenol removal in wastewater treatment. Two kinds of typical biomass waste material, namely, coconut shell and lignin, were used. Physical activation (steam activation) and chemical activation methods were compared. Results show that steam activation is an effective method for coconut shell AC production. The largest Brunauer-Emmett-Teller (BET) surface area was 1065 m2/g at 800 °C. Chemical activation could produce AC samples with higher BET specific surface area. The lignin AC with K2CO3 activation has the largest BET surface of 1723.8 m2/g at 800 °C. FTIR results indicated that K2CO3 activation could greatly enhance the formation of surface oxygen-containing functional groups. Both coconut shell AC and lignin AC samples show excellent performance for phenol removal. The highest phenol removal efficiency for coconut shell AC and lignin AC are 96.87% and 98.22%, respectively. Adsorption kinetic analysis show that the pseudo-first-order kinetic model is able to describe the adsorption characteristics of phenol in wastewater treatment. Recycling properties show that regeneration of lignin AC could maintain high adsorption performance for phenol.
ABSTRACT
Roxarsone (ROX), commonly employed as a livestock feed additive, largely remains unmetabolized and is subsequently excreted via feces. ROX could cause serious environmental risks due to its rapid transformation and high mobility in the anaerobic subsurface environment. Dissolved organic matter (DOM) is an important constituent of fecal organics in livestock waste and could affect the ROX biotransformation. Nonetheless, the underlying mechanisms governing the interaction between DOM and ROX biotransformation have not yet been elucidated in the anaerobic environment. In this study, the changes of ROX, metabolites, and microbial biomass in the solutions with varying DOM concentrations (0, 50, 100, 200, and 400 mg/L) under anaerobic environments were investigated during the ROX (200 mg/L) degradation. EEM-PARAFAC and metagenomic sequencing were combined to identify the dynamic shifts of DOM components and the functional microbial populations responsible for ROX degradation. Results indicated that DOM facilitated the anaerobic biotransformation of ROX and 200 mg/L ROX could be degraded completely in 28 h. The tryptophan-like within DOM functioned as a carbon source to promote the growth of microorganisms, thus accelerating the degradation of ROX. The mixed microflora involved in ROX anaerobic degrading contained genes associated with arsenic metabolism (arsR, arsC, acr3, arsA, nfnB, and arsB), and arsR, arsC, acr3 exhibited high microbial diversity. Variations in DOM concentrations significantly impacted the population dynamics of microorganisms involved in arsenic metabolism (Proteiniclasticum, Exiguobacterium, Clostridium, Proteiniphilum, Alkaliphilus, and Corynebacterium spp.), which in turn affected the transformation of ROX and its derivatives. This study reveals the mechanism of ROX degradation influenced by the varying concentrations of DOM under anaerobic environments, which is important for the prevention of arsenic contamination with elevated levels of organic matter.
Subject(s)
Biodegradation, Environmental , Biotransformation , Microbiota , Roxarsone , Roxarsone/metabolism , Anaerobiosis , Microbiota/drug effects , Bacteria/metabolism , Bacteria/genetics , Bacteria/classificationABSTRACT
Clay colloids in the subsurface environment have a strong adsorption capacity for radionuclides, and the mobile colloids will carry the nuclides for migration, which would promote the movability of radionuclides in the groundwater environment and pose a threat to the ecosphere. The investigations of the adsorption/desorption behaviors of radionuclides in colloids and porous media are significant for the evaluation of the geological disposal of radioactive wastes. To illustrate the adsorption/desorption behaviors of 241Am(â ¢) in Na-montmorillonite colloid and/or quartz sand systems at different pH (5, 7 and 9), ionic strengths (0, 0.1 and 5 mM), colloid concentrations (300 and 900 mg/L), nuclide concentrations (500, 800, 1100 and 1400 Bq/mL) and grain sizes (40 and 60 mesh), a series of batch sorption-desorption experiments were conducted. Combining the analysis of the physical and chemical properties of Na-montmorillonite with the Freundlich model, the influencing mechanism of different controlling factors is discussed. The experimental results show that the adsorption/desorption behaviors of 241Am(â ¢) in Na-montmorillonite colloid and/or quartz sand strongly are influenced by the pH value and ionic strength of a solution, the colloid concentration as well as quartz sand grain size. The adsorption and desorption isotherms within all the experimental conditions could be well-fitted by the Freundlich model and the correlation coefficients (R2) are bigger than 0.9. With the increase in pH, the adsorption partition coefficient (Kd) at 241Am(â ¢)-Na-montmorillonite colloid two-phase system and 241Am(â ¢)-Na-montmorillonite colloid-quartz sand three-phase system presents a trend which increases firstly followed by decreasing, due to the changes in the morphology of Am with pH. The Kd of 241Am(â ¢) adsorption on montmorillonite colloid and quartz sand decreases with increasing in ionic strength, which is mainly attributed to the competitive adsorption, surface complexation and the reduction of surface zeta potential. Additionally, the Kd increases with increasing colloid concentrations because of the increase in adsorption sites. When the mean grain diameter changes from 0.45 to 0.3 mm, the adsorption variation trends of 241Am(â ¢) remain basically unchanged. The research results obtained in this work are meaningful and helpful in understanding the migration behaviors of radionuclides in the underground environment.
Subject(s)
Americium , Bentonite , Colloids , Quartz , Bentonite/chemistry , Osmolar Concentration , Adsorption , Hydrogen-Ion Concentration , Colloids/chemistry , Quartz/chemistry , Americium/chemistry , Americium/analysis , Water Pollutants, Radioactive/chemistry , Water Pollutants, Radioactive/analysis , Soil Pollutants, Radioactive/analysis , Soil Pollutants, Radioactive/chemistry , Models, Chemical , Particle Size , Sand/chemistryABSTRACT
Americium (III) (Am(III)) in the natural environment is considered immobile due to its low solubility, strong adsorption, and high affinity to solid surfaces. However, the presence of natural colloids may carry Am(III) transport for long distance. The individual and co-transport behaviors of Am(III) and natural colloids through the unsaturated packed columns were investigated under the influence of pH, electrolyte concentration, velocity, Am(III) concentration and natural colloids concentration. Under all experimental conditions, Am(III) individual transport construct sight breakthrough curves (BTCs, CAm/C0 < 3%), but the presence of natural colloids increased the BTCs plateau of Am(III) significantly (30% < CAm/C0 < 80%), indicating that the colloids were able to promote Am(III) transport in the unsaturated porous media. DLVO theoretical calculations reveal that the increased pH and decreased electrolyte concentration lead to a rase in electrostatic repulsion, and the natural colloids tend to be dispersed and stabilized, which facilitates elution. In addition to this, the increase of velocity and colloids concentration will lead to greater breakthrough of natural colloids. The non-equilibrium two-site model and the two-site kinetic retention model well-described the BTCs of Am(III) and natural colloids, respectively. This study provide new insights into the behavior of natural colloids carrying the Am(III) into aquifers through the vadose zone sediments.
Subject(s)
Americium , Colloids , Geologic Sediments , Colloids/chemistry , Geologic Sediments/chemistry , Americium/chemistry , Adsorption , Water Pollutants, Chemical/chemistry , Kinetics , Hydrogen-Ion ConcentrationABSTRACT
The rapid industrial growth has generated heavy metal(loid)s contamination in the soil, which poses a serious threat to the ecology and human health. In this study, 580 samples were collected in Henan Province, China, for source apportionment, migration characterization and health risk evaluation using self-organizing map, positive matrix factorization and multivariate risk assessment methods. The results showed that samples were classified into four groups and pollution sources included chromium slag dump, soil parent rock and abandoned factory. The contents of Cr, Pb, As and Hg were low in Group 1. Group 2 was characterized by total Cr, Cr(â ¥) and pH. The enrichment of total Cr and Cr(â ¥) in soil was mainly attributed to chromium slag dump, accounting for more than 84.0%. Group 3 was dominated by Hg and Pb. Hg and Pb were primarily attributed to abandoned factory, accounting for 84.7% and 70.0%, respectively. Group 4 was characterized by As. The occurrence of As was not limited to one individual region. The contribution of soil parent rock reached 83.0%. Furthermore, the vertical migration of As, Hg, Pb and Cr(â ¥) in soil was mainly influenced by medium permeability, pH and organic matter content. The trends of As, Pb, and Hg with depth were basically consistent with the trends of organic matter with depth, and were negatively correlated with the change in pH with depth. The trends of Cr(â ¥) with depth were basically consistent with the changes in pH with the depth. The content of Cr(â ¥) in the deep soil did not exceed the detection limits and Cr(â ¥) contamination occurred in the deep aquifer, suggesting that Cr(â ¥) in the deep groundwater originated from the leakage of shallow groundwater. The assessment indicated that the non-carcinogenic and carcinogenic risks for children and adults could not be neglected. Moreover, children were more susceptible than adults.
Subject(s)
Groundwater , Mercury , Metals, Heavy , Soil Pollutants , Adult , Child , Humans , Soil/chemistry , Lead , Soil Pollutants/analysis , Environmental Monitoring/methods , Metals, Heavy/analysis , Chromium , China , Risk Assessment , CadmiumABSTRACT
The particle concentration effect on Kd values of radionuclides has been observed but the underlying mechanism remains controversial. The hope is to use the relationship between particle concentration, adsorption-desorption isotherms and reversibility, in combination with surface component activity of model (SCA model), to solve this issue. 137Cs, 60Co, 90Sr were used as tracers, batch experiments were conducted in freshwater-sediment and seawater-sediment. The experiment of each radionuclide was designed with five different particle concentrations Cp, and for each Cp there were seven different initial concentrations C0. After adsorption experiments, four consecutive desorption experiments were carried out. At the fourth desorption experiment, radionuclide concentrations in the supernatant and sediment were measured. The results showed that adsorption and single desorption data of 137Cs, 60Co, 90Sr might be described by linear isotherms. 137Cs was reversible in the seawater-sediment, so hysteresis angles of the five-particle concentration were approximately 0°, all adsorption and desorption data could be classified into one line. In the remaining systems, besides the adsorption and single desorption isotherms moved upward with the decrease of particle concentration, hysteresis angles and irreversibility also increased, thus, the particle concentration effect was obvious. The reversible and resistant component concentrations calculated by adsorption, single desorption and consecutive desorption isotherm were linear functions of equilibrium concentration Ce1, respectively. Data from adsorption and desorption experiments with particle concentration effect could be classified into the same line using the Freundlich-SCA model. The results of this study indicate that the particle concentration effect is related to reversibility. When adsorption isotherm and single desorption isotherm are both linear, consecutive desorption isotherm, reversible and resistant component concentrations approach linearity too. After the Freundlich-SCA model eliminated the particle concentration effect on adsorption and desorption data, the data can be used to predict the adsorption, single desorption isotherm and Kd value at any particle concentration.
Subject(s)
Radiation Monitoring , Adsorption , RadioisotopesABSTRACT
Solute transport modeling resolves advection, dispersion, and chemical reactions in groundwater systems with its accuracy depending on the resolution of domain at all scales, thus the computational efficiency of a simulator becomes a bottleneck for the wide application of numerical simulations. However, the traditional serial numerical simulators have reached their limits for the prohibitive computational time and memory requirement in solving large-scale problems. These limitations have greatly hindered the wide application of groundwater solute transport modeling. Thus, the development of an efficient method for handling large-scale groundwater solute transport simulation is urgently required. In this study, we developed and assessed a parallelized MT3DMS (Modular Three-Dimensional Multispecies Transport Model) by using OpenMP (Open specifications for Multi-Processing) to accelerate the solute transport simulation process. The parallelization was achieved by adding OpenMP compile directives (i.e., defining various types of parallel regions) into the most time-consuming packages, including the Advection package (ADV), Dispersion package (DSP), and Generalized Conjugate Gradient Solver package (GCG). This allows parallel processing on shared-memory multiprocessors, i.e., both the memory requirement and computing efforts are automatically distributed among all processors. Moreover, we discussed two different parallelization strategies for handling numerical models with either many layers or few layers. The performance of parallelized MT3DMS was assessed by two benchmark numerical models with different model domain sizes via a workstation with two quad-core processors. Results showed that the running time of parallelized MT3DMS can be 4.15 times faster than that using sequential MT3DMS. The effects of using different preconditioners (procedures that transform a given problem into a form that is more suitable for numerical solving methods) in the GCG package were additionally evaluated. The modified strategy for handling numerical models with few layers also achieved satisfactory results with running time two times faster than that via sequential simulation. Thus, the proposed parallelization allows high-resolution groundwater transport simulation with higher efficiency for large-scale or multimillion-cell simulation problems.
Subject(s)
Groundwater/chemistry , Models, Theoretical , Water MovementsABSTRACT
In this study, the hydrochemical characteristics of shallow groundwater were analyzed to get insight into the factors affecting groundwater quality in a typical agricultural dominated area of the North China Plain. Forty-four shallow groundwater samples were collected for chemical analysis. The water type changes from Ca·Na-HCO3 type in grass land to Ca·Na-Cl (+NO3) type and Na (Ca)-Cl (+NO3+SO4) type in construction and facility agricultural land, indicating the influence of human activities. The factor analysis and geostatistical analysis revealed that the two major factors contributing to the groundwater hydrochemical compositions were the water-rock interaction and contamination from sewage discharge and agricultural fertilizers. The major ions (F, HCO3) and trace element (As) in the shallow groundwater represented the natural origin, while the nitrate and sulfate concentrations were related to the application of fertilizer and sewage discharge in the facility agricultural area, which was mainly affected by the human activities. The values of pH, total dissolved solids, electric conductivity, and conventional component (K, Ca, Na, Mg, Cl) in shallow groundwater increased from grass land and cultivated land, to construction land and to facility agriculture which were originated from the combination sources of natural processes (e.g., water-rock interaction) and human activities (e.g., domestic effluents). The study indicated that both natural processes and human activities had influences on the groundwater hydrochemical compositions in shallow groundwater, while anthropogenic processes had more contribution, especially in the reclaimed water irrigation area.
Subject(s)
Agricultural Irrigation/methods , Environmental Monitoring/methods , Groundwater/chemistry , Human Activities , Sewage/analysis , Water Pollutants, Chemical/analysis , China , Fertilizers/analysis , Groundwater/standards , Humans , Water QualityABSTRACT
Based on the geo-statistical theory and ArcGIS geo-statistical module, datas of 30 groundwater level observation wells were used to estimate the decline of groundwater level in Beijing piedmont. Seven different interpolation methods (inverse distance weighted interpolation, global polynomial interpolation, local polynomial interpolation, tension spline interpolation, ordinary Kriging interpolation, simple Kriging interpolation and universal Kriging interpolation) were used for interpolating groundwater level between 2001 and 2013. Cross-validation, absolute error and coefficient of determination (R(2)) was applied to evaluate the accuracy of different methods. The result shows that simple Kriging method gave the best fit. The analysis of spatial and temporal variability suggest that the nugget effects from 2001 to 2013 were increasing, which means the spatial correlation weakened gradually under the influence of human activities. The spatial variability in the middle areas of the alluvial-proluvial fan is relatively higher than area in top and bottom. Since the changes of the land use, groundwater level also has a temporal variation, the average decline rate of groundwater level between 2007 and 2013 increases compared with 2001-2006. Urban development and population growth cause over-exploitation of residential and industrial areas. The decline rate of the groundwater level in residential, industrial and river areas is relatively high, while the decreasing of farmland area and development of water-saving irrigation reduce the quantity of water using by agriculture and decline rate of groundwater level in agricultural area is not significant.
ABSTRACT
To accelerate the groundwater flow simulation process, this paper reports our work on developing an efficient parallel simulator through rebuilding the well-known software MODFLOW on JASMIN (J Adaptive Structured Meshes applications Infrastructure). The rebuilding process is achieved by designing patch-based data structure and parallel algorithms as well as adding slight modifications to the compute flow and subroutines in MODFLOW. Both the memory requirements and computing efforts are distributed among all processors; and to reduce communication cost, data transfers are batched and conveniently handled by adding ghost nodes to each patch. To further improve performance, constant-head/inactive cells are tagged and neglected during the linear solving process and an efficient load balancing strategy is presented. The accuracy and efficiency are demonstrated through modeling three scenarios: The first application is a field flow problem located at Yanming Lake in China to help design reasonable quantity of groundwater exploitation. Desirable numerical accuracy and significant performance enhancement are obtained. Typically, the tagged program with load balancing strategy running on 40 cores is six times faster than the fastest MICCG-based MODFLOW program. The second test is simulating flow in a highly heterogeneous aquifer. The AMG-based JASMIN program running on 40 cores is nine times faster than the GMG-based MODFLOW program. The third test is a simplified transient flow problem with the order of tens of millions of cells to examine the scalability. Compared to 32 cores, parallel efficiency of 77 and 68% are obtained on 512 and 1024 cores, respectively, which indicates impressive scalability.
Subject(s)
Computer Simulation , Groundwater/analysis , Water Movements , Algorithms , China , Software , Water SupplyABSTRACT
Ground water plays an important role in water supply and the ecology of arid to semiarid areas such as Northwest China, where the landscape is fragile due to frequent drought in the past few decades. This paper discusses the role of ground water in these ecosystems, including the effect of condensation water and water table depth on the growth of plants and degree of soil salinity. The paper also discusses the controlling process for land desertification and soil salinization in Northwest China. Water table depth is a key factor controlling the water balance, ground water flow, and salt transport in the vadose zone. The suitable water table depth for vegetation growth, which can prevent land desertification and soil salinization, is within a range of 2 to 4 m; the optimal depth is approximately 3 m. As examples, changes in ecosystems owing to water resources development in Tarim and Manas basins, Xinjiang, China, are discussed.