Highly Adhesive and Stretchable Epidermal Electrode for Bimodal Recording Patch.

For numerous biological and human-machine applications, it is critical to have a stable electrophysiological interface to obtain reliable signals. To achieve this, epidermal electrodes should possess conductivity, stretchability, and adhesiveness. However, limited types of materials can simultaneously satisfy these requirements to provide satisfying recording performance. Here, we present a dry electromyography (EMG) electrode based on conductive polymers and tea polyphenol (CPT), which offers adhesiveness (0.51 N/cm), stretchability (157%), and low impedance (14 kΩ cm2 at 100 Hz). The adhesiveness of the electrode is attributed to the interaction between catechol groups and hydroxyls in the polymer blend. This adhesive electrode ensures stable EMG recording even in the presence of vibrations and provides signals with a high signal-to-noise ratio (>25 dB) for over 72 h. By integrating the CPT electrode with a liquid metal strain sensor, we have developed a bimodal rehabilitation monitoring patch (BRMP) for sports injuries. The patch utilizes Kinesio Tape as a substrate, which serves to accelerate rehabilitation. It also tackles the challenge of recording with knee braces by fitting snugly between the brace and the skin, due to its thin and stretchable design. CPT electrodes not only enable BRMP to assist clinicians in formulating effective rehabilitation plans and offer patients a more comfortable rehabilitation experience, but also hold promise for future applications in biological and human-machine interface domains.

Electronic exoneuron based on liquid metal for the quantitative sensing of the augmented somatosensory system.

The increasing demands in augmented somatosensory have promoted quantitative sensing to be an emerging need for athletic training/performance evaluation and physical rehabilitation. Neurons for the somatosensory system in the human body can capture the information of movements in time but only qualitatively. This work presents an electronic Exo-neuron (EEN) that can spread throughout the limbs for realizing augmented somatosensory by recording both muscular activity and joint motion quantitatively without site constraints or drift instability, even in strenuous activities. Simply based on low-cost liquid metal and clinically used adhesive elastomer, the EEN could be easily fabricated in large areas for limbs. It is thin (~120 µm), soft, stretchable (>500%), and conformal and further shows wide applications in sports, rehabilitation, health care, and entertainment.

Recent progress in fiber-based soft electronics enabled by liquid metal.

Soft electronics can seamlessly integrate with the human skin which will greatly improve the quality of life in the fields of healthcare monitoring, disease treatment, virtual reality, and human-machine interfaces. Currently, the stretchability of most soft electronics is achieved by incorporating stretchable conductors with elastic substrates. Among stretchable conductors, liquid metals stand out for their metal-grade conductivity, liquid-grade deformability, and relatively low cost. However, the elastic substrates usually composed of silicone rubber, polyurethane, and hydrogels have poor air permeability, and long-term exposure can cause skin redness and irritation. The substrates composed of fibers usually have excellent air permeability due to their high porosity, making them ideal substrates for soft electronics in long-term applications. Fibers can be woven directly into various shapes, or formed into various shapes on the mold by spinning techniques such as electrospinning. Here, we provide an overview of fiber-based soft electronics enabled by liquid metals. An introduction to the spinning technology is provided. Typical applications and patterning strategies of liquid metal are presented. We review the latest progress in the design and fabrication of representative liquid metal fibers and their application in soft electronics such as conductors, sensors, and energy harvesting. Finally, we discuss the challenges of fiber-based soft electronics and provide an outlook on future prospects.

Effect of potassium fertilization on storage root number, yield, and appearance quality of sweet potato (Ipomoea batatas L.).

Increasing storage root number is a pivotal approach to enhance both storage root (SR) yield and appearance quality of sweet potato. Here, 2-year field experiments were conducted to investigate the effect of 0 (K0), 120 (K1), 240 (K2), and 360 (K3) kg ha-1 potassium fertilizer (K2O) on lignin metabolism, root growth, storage root yield, and uniformity. The results demonstrated that potassium (K) application led to a decrease in the activities of key enzymes involved in lignin biosynthesis, including phenylalanine deaminase (PAL), 4-coumarate coenzyme A ligase (4-CL), cinnamic acid dehydrogenase (CAD), polyphenol oxidase (PPO), and peroxidase (POD). This resulted in a significant reduction in lignin and G-type lignin contents in potential SRs compared to K0 treatment within 10-30 days after planting (DAP). BJ553 exhibited a significant decrease in PAL activity, as well as lignin and G-type contents at 10 DAP, whereas YS25 showed delayed effects until 20 DAP. However, the number and distribution of secondary xylem conduits as well as the mid-column diameter area in roots were increased in K2 treatment. Interestingly, K2 treatment exhibited significantly larger potential SR diameter than other treatments at 15, 20, and 25 DAP. At harvest, K2 treatment increased the SR number, the single SR weight, and overall yield greatly compared with K0 treatment, with an average increase of 19.12%, 16.54%, and 16.92% respectively. The increase of SR number in BJ553 was higher than that of YS25. Furthermore, K2 treatment exhibited the lowest coefficient of variation for both SR length and diameter, indicating a higher yield of middle-sized SRs. In general, appropriate potassium application could effectively suppress lignin biosynthesis, leading to a reduction in the degree of pericycle lignification in potential SRs. This promotes an increase in the number of storage roots and ultimately enhances both yield and appearance quality of sweet potato. The effect of potassium fertilizer on lignin metabolism in BJ553 roots was earlier and resulted in a greater increase in the SR number compared to YS25.

Stretchable Liquid Metal-Based Metal-Polymer Conductors for Fully Screen-Printed Biofuel Cells.

We reported a straightforward and low-cost method to fabricate stretchable biofuel cells by using liquid metal-based metal-polymer conductors. The liquid-metal-based metal-polymer conductors had a conductivity of 2.7 × 105 S/m and a stretchability larger than 200%, giving the biofuel cell good conformability to the skin. The glucose biofuel cells (BFCs) yielded a maximum power density as 14.11 µW/cm2 at 0.31 V with 0.2 mM glucose, while the lactate BFCs reached 31.00 µW/cm2 at 0.51 V with 15 mM lactate. The results of 24 h short circuit current density showed that, with enough biofuel, this patch could be used over the course of an entire day for wearable sensors.

Skin Electronics from Biocompatible In Situ Welding Enabled By Intrinsically Sticky Conductors.

Welding usually involves high temperatures, toxic solvents, or conditions not compatible with human bodies, which severely limit the fusion of electronics and human tissues. To achieve direct welding of electronics on human skin, the intrinsically sticky conductors that can simultaneously achieve metal-grade electrical conductivity (≈41 7000 S m-1 ), hydrogel-grade stretchability (>900% strain), and self-adhesiveness (1.8 N cm-1 ) are reported. The sticky conductors composed of gallium indium alloy and acrylate polymer adhesives have a surface-enriched structure, which can form instant mechanical and electrical connections with different surfaces through gentle pressure without involving conditions that may damage human tissues. Based on the sticky conductors, the in situ welding of electronics on the skin is realized. To demonstrate the feasibility of in situ welding, electronic tattoos are achieved for movement monitoring. Intrinsically sticky electrodes that can resist drying and simultaneously deform with the skin for electrophysiological measurement are also developed.

Multilayered electronic transfer tattoo that can enable the crease amplification effect.

Electronic tattoos have great potential in health and movement sensing applications on the skin. However, existing electronic tattoos cannot be conformal, sticky, and multilayered at the same time. Here, we have achieved multilayered integration of the electronic tattoo that is highly stretchable (800%), conformal, and sticky. This electronic tattoo can enable the crease amplification effect, which can amplify the output signal of integrated strain sensors by three times. The tattoo can be transferred to different surfaces and form a firm attachment, where no solvent or heat is needed. The tattoo fabrication is straightforward and scalable; a layer-by-layer strategy and two materials (metal-polymer conductors and the elastomeric block copolymer) are used to fabricate the circuit module with desirable numbers of layers within the tattoo. A three-layered tattoo integrating 1 heater and 15 strain sensors is developed for temperature adjustment, movement monitoring, and remote control of robots.

Highly Stretchable Metal-Polymer Conductor Electrode Array for Electrophysiology.

Narrowing the mechanical mismatch between biological tissues (typically soft) and neural interfaces (hard) is essential for maintaining signal quality for the electrical recording of neural activity. However, only a few materials can satisfy all requirements for such electronics, which need to be both biocompatible and sufficiently soft. Here, a highly stretchable electrode array (SEA) is introduced, based on the liquid metal-polymer conductor (MPC), achieving high mechanical flexibility and good cytocompatability for neural interfaces. By utilizing the MPC, the SEA exhibits high stretchability (≈100%) and excellent cycling stability (>400 cycles). The cytocompatability of the SEA can allow for long-term culturing of primary neurons and enable signal recording of primary hippocampal neurons. In the future, the SEA could serve as a reliable and robust platform for diagnostics in neuronal tissues and greatly advance brain-machine interfaces.

Highly Stretchable and Biocompatible Liquid Metal-Elastomer Conductors for Self-Healing Electronics.

Highly stretchable, conductive, biocompatible conductors, and connectors are crucial for the fabrication of flexible devices. However, it remains a problem to get highly stretchable, conductive materials with low cost on a large scale. Another problem in production is the connection between soft and rigid components. Here, a new conductive nanocomposite is reported by mixing the 11-mercaptoundecanoic acid (MUA) modified liquid metal (LM) nanoparticles with polystyrene-block-polybutadiene-block-polystyrene (SBS), which is biocompatible (in vivo and in vitro), conductive (12 000 S cm-1 of conductivity), and stretchable (800% of elongation). Apart from its good performance, this material can be produced on a large scale by using a commercial polymer product and a straightforward physical production process. MUA is used to compromise the dense "gallium oxide shell" of liquid metal nanoparticles such that the whole composite can become conductive. By using resin to modify this composite, this new conductive material can be adhesive and highly conductive, and serve as a stable and efficient connector between soft conductor and rigid component.

A Soft, Conductive External Stent Inhibits Intimal Hyperplasia in Vein Grafts by Electroporation and Mechanical Restriction.

Intimal hyperplasia (IH) in vein grafts (VGs) is a major issue in coronary artery bypass grafting (CABG) surgery. Although external stents can attenuate IH of VGs to some extent, none of the existing external stents have shown satisfactory clinical outcomes. Here we develop a flexible, biodegradable, and conductive external metal-polymer conductor stent (MPCS) that can electroporate the vessel wall and produce a protein that prevents IH. We designed the plasmid DNA encoding the tissue inhibitor of metalloproteinases-3 (TIMP-3) and lyophilized it on the inner surface of the MPCS to deliver into the adventitia and the middle layer of VGs for gene therapy. Coupled with its continuous mechanical support to prevent dilation after implanting, the MPCS can inhibit the IH of VGs significantly in the rabbit model. This proof-of-concept demonstration may aid the development of other implantable bioelectronics for electroporation gene therapy.

Large-Scale Fabrication of Highly Elastic Conductors on a Broad Range of Surfaces.

Recently, great stretchability progress has been witnessed in elastic electronics. However, such electronics are costly, toxic, or cannot pattern on a broad range of substrates, which limit their large-scale fabrications and applications. Here, to overcome those limitations, an ink comprising liquid metal particles and desirable polymer solutions is developed. The polymer solutions in our ink can be adjusted to print on different surfaces and avoid toxic organic solvents in most cases. The ink can be sintered by a small strain (∼10%) in room temperature. Using our ink, conductors with high stretchability (380000 S/m at a strain of 1000%) can be printed in low consumption (liquid metal consumption 3.27 mg/cm2), in a large area (bestrew the entire surface of a T-shirt), and in high throughputs (∼105 cm2/h). The ink can be printed on a T-shirt to achieve a smart wearable platform that integrates electronics for strain/electrophysiology/electrochemistry detection and temperature monitoring/controlling.

Printable Metal-Polymer Conductors for Highly Stretchable Bio-Devices.

Stretchable, biocompatible devices can bridge electronics and biology. However, most stretchable conductors for such devices are toxic, costly, and regularly break/degrade after several large deformations. Here we show printable, highly stretchable, and biocompatible metal-polymer conductors by casting and peeling off polymers from patterned liquid metal particles, forming surface-embedded metal in polymeric hosts. Our printable conductors present good stretchability (2,316 S/cm at a strain of 500%) and repeatability (ΔR/R <3% after 10,000 cycles), which can satisfy most electrical applications in extreme deformations. This strategy not only overcomes large surface tension of liquid metal but also avoids the undesirable sintering of its particles by stress in deformations, such that stretchable conductors can form on various substrates with high resolution (15 µm), high throughput (∼2,000 samples/hour), and low cost (one-quarter price of silver). We use these conductors for stretchable circuits, motion sensors, wearable glove keyboards, and electroporation of live cells.

A Strategy for Rapid Construction of Blood Vessel-Like Structures with Complex Cell Alignments.

A method is developed that can rapidly produce blood vessel-like structures by bonding cell-laden electrospinning (ES) films layer by layer using fibrin glue within 90 min. This strategy allows control of cell type, cell orientation, and material composition in separate layers. Furthermore, ES films with thicker fibers (polylactic-co-glycolic acid, fiber diameter: ≈3.7 µm) are used as cell-seeding layers to facilitate the cell in-growth; those with thinner fibers (polylactic acid, fiber diameter: ≈1.8 µm) are used as outer reinforcing layers to improve the mechanical strength and reduce the liquid leakage of the scaffold. Cells grow, proliferate, and migrate well in the multilayered structure. This design aims at a new type of blood vessel substitute with flexible control of parameters and implementation of functions.

Gold nanoclusters-assisted delivery of NGF siRNA for effective treatment of pancreatic cancer.

Pancreatic cancer is one of the deadliest human cancers, whose progression is highly dependent on the nervous microenvironment. The suppression of gene expression of nerve growth factor (NGF) may have great potential in pancreatic cancer treatment. Here we show that gold nanocluster-assisted delivery of siRNA of NGF (GNC-siRNA) allows efficient NGF gene silencing and pancreatic cancer treatment. The GNC-siRNA complex increases the stability of siRNA in serum, prolongs the circulation lifetime of siRNA in blood and enhances the cellular uptake and tumour accumulation of siRNA. The GNC-siRNA complex potently downregulates the NGF expression in Panc-1 cells and in pancreatic tumours, and effectively inhibits the tumour progression in three pancreatic tumour models (subcutaneous model, orthotopic model and patient-derived xenograft model) without adverse effects. Our study constitutes a straightforward but effective approach to inhibit pancreatic cancer via NGF knockdown, suggesting a promising therapeutic direction for pancreatic cancer.