Thermal Evaluation of Multi-Antenna Systems Proposed to Treat Bone Tumors: Finite Element Analysis.

Microwave ablation is commonly used in soft tissue tumors, but its application in bone tumors has been barely analyzed. Antennas to treat bone tissue (~3 cm2), has been lately designed. Bone tumors at pathological stage T1 can reach 8 cm wide. An antenna cannot cover it; therefore, our goal is to evaluate the thermal performance of multi-antenna arrays. Linear, triangular, and square configurations of double slot (DS) and monopole (MTM) antennas were evaluated. A parametric study (finite element method), with variations in distance between antennas (ad) and bone thickness (bt) was implemented. Array feasibility was evaluated by SWR, ablated tissue volume, etc. The linear configuration with DS and MTM antennas showed SWR ≤ 1.6 for ad = 1 mm−15 mm and bt = 20 mm−40 mm, and ad = 10 mm−15 mm and bt = 25 mm−40 mm, respectively; the triangular showed SWR ≤ 1.5 for ad = 5 mm−15 mm and bt = 20 mm−40 mm and ad = 10 mm−15 mm and bt = 25 mm−40 mm. The square configuration (DS) generated SWR ≤ 1.5 for ad = 5 mm−20 mm and bt = 20 mm−40 mm, and the MTM, SWR ≤ 1.5 with ad = 10 mm and bt = 25 mm−40 mm. Ablated tissue was 4.65 cm3−10.46 cm3 after 5 min. According to treatment time and array configuration, maximum temperature and ablated tissue is modified. Bone tumors >3 cm3 can be treated by these antenna-arrays.

A Computational Evaluation of the temperature distribution generated by thermal splints designed to treat knee pain.

A 3D modeling study was performed to evaluate the temperature distribution produced due to knee thermal splints to facilitate future investigations into the possible relationship between the temperature distribution and the pain relief related performance of the splints. Water and phase change material (PCM) were used as splint fillers at two different temperatures (42 °C and 44 °C). Free cooling and a temperature-controlled thermal splint were also considered. The study showed that a PCM filled splint or a temperature-controlled splint produced relatively larger and deeper temperature changes compared to the one produced with a water filled splint. With a PCM filled splint it was possible to reach a temperature increase of 1 °C in muscle tissue (42.61 cm3) and not only in fatty tissue.

Sugar Concentration Measurement System Using Radiofrequency Sensor.

A sugar solution measurement system was developed based on the dielectric properties of the sucrose molecule. An ac conductivity and tan δ study as a function of the frequency was performed to find the suitable frequency range for the measuring system. The results indicate that it is possible to obtain a better response of the sensor using the frequencies as the maxima peak in tan δ appears. Developed setup for sucrose solution was appropriate to measure in a 0.15 to 1 g/mL range with an experimental error of about 3%. The proposed system improves the measurement time over some other methods.

Impact of silicone and metal port-a-cath implants on superficial hyperthermia treatment quality.

PURPOSE: A port-a-cath is a device implanted under the skin for continuous drug administration. It is composed of a catheter and a silicone or metal reservoir. A simulation study was done to assess the impact of a port-a-cath implant on the quality of superficial hyperthermia treatments applied using the Lucite cone applicator (LCA). METHODS: Specific absorption rate (SAR) and temperature distributions were predicted using SEMCAD-X (version 14.8). We simulated 72 arrangements: two LCA-implant set-ups (central port-a-cath or at an edge below the LCA footprint), six translations of the LCA per set-up, two LCA orientations (Parallel or perpendicular electric field direction) per set-up, two implant materials (silicon or metal) and a control without port-a-cath. Treatment quality was quantified by the average 1 g SAR coverage (CV25%), i.e. volume within the 25% iso-SAR surface, and the volume within the 40 °C iso-temperature surface (CV40 °C). RESULTS: CV25% reduced with a silicon port-a-cath located below the LCA footprint. In the worst scenario, only 64% of the CV25% of the control set-up was achieved. For a metal port-a-cath below the LCA aperture, dramatic reductions of CV25% were predicted: worst scenario down to 12.1% of the control CV25%. For the CV40 °C the worst case values were 74.5% and 6.5%, for silicon and metal implants, respectively. CONCLUSIONS: A silicone port-a-cath below the LCA had a smaller effect on treatment quality than a metal implant. Based on this study we recommend verifying heating quality by 3D patient-specific treatment planning when a port-a-cath is located below the footprint of the applicator.