Crosslinked carboxymethyl cellulose colloidal solution for cotton thread coating in wound dressing: A rheological study.

Cotton thread therapeutic properties as a wound dressing can be enhanced by utilising carboxymethyl cellulose-nanoparticles (CMC/NPs) colloidal solution as a coating solution. Nanoparticles such as graphene oxide (GO), graphene quantum dots (GQD), and silver nanoparticles (AgNP) stability in CMC was investigated through the rheological analysis and UV-Vis spectroscopy of the colloidal solutions. Citric acid (CA) acted as a crosslinker and was utilised to crosslink the colloidal solution with cotton thread. These CMC/NPs coated threads were subjected to mechanical properties and antibacterial activity analysis. Results obtained indicate less nanoparticle agglomeration and were stable in the CMC-based nanofluid. CMC/NPs rheological study suggested that colloidal solutions exhibited shear thinning behaviour and behaved as non-Newtonian fluids with n < 1. Crosslinked CMC/NPs appeared in a gel-like state as the viscoelasticity of the solution increased. Among the colloidal solutions, CMC/AgNP showed the highest enhancement with a significant difference at p < 0.05 in terms of mechanical and antibacterial properties. Consequently, the rheological properties and stability of CMC/NPs might influence the coating solution's appearance and refine the cotton thread's microstructure for a functional wound dressing to be further utilised as a coating solution for antibacterial cotton thread wound dressing material.

Effects of carboxymethyl cellulose fiber formations with chitosan incorporation via coating and mixing processes.

To date, the utilization of carboxymethyl cellulose (CMC) fibers are only restricted to weak mechanical application such as wound dressing. Physically, CMC has a weak mechanical strength due to the high hydrophilicity trait. However, this flaw was saved by the extensive number of reactive functional groups, allowing this macromolecule to form linkages with chitosan to ensure its versatility. This work successfully fabricated CMC-chitosan fiber via dissolution, crosslinking, dry-jet wet-spinning extrusion, and coagulation processes. Chitosan was constituted with CMC fiber in two approaches, coating, and inclusion at various concentrations. Morphologically, chitosan incorporation has triggered agglomerations and roughness toward CMC fibers (CMCF). Chemically, the interaction between CMC and chitosan was proved through FTIR analysis at peaks 1245 cm-1 (ECH covalent crosslinking), while 3340 cm-1 and 1586 cm-1 were due to ionic and hydrogen bonding. The result from analysis showed that at higher chitosan concentrations, the chitosan-included CMC fiber (CMCF-I) and chitosan-coated CMC fiber (CMFC) were mechanically enhanced (up to 86.77 and 82.72 MPa), thermally more stable (33 % residual mass), and less hydrophilic compared to the plain CMCF. The properties of CMC-chitosan fibers have opened up vast possible applications, especially as a reinforcement in a watery medium such as a hydrogel.

Chitosan-Bead-Encapsulated Polystyrene Sulfonate for Adsorption of Methylene Blue and Regeneration Studies: Batch and Continuous Approaches.

Textile industrialization causes water pollution due to the discharge of industrial effluents into the environment. To reduce the impact of industrial effluent, it must be treated in wastewater treatment plants before discharge into rivers. Among all wastewater treatment approaches, the adsorption process is one method to remove pollutants from wastewater, but it has some limitations in term of reusability and ionic selective adsorption properties. In this study, we prepared cationic poly (styrene sulfonate) (PSS)-incorporated anionic chitosan beads synthesized using the oil-water emulsion coagulation method. The produced beads were characterized using FESEM and FTIR analysis. In batch adsorption studies, the PSS-incorporated chitosan beads exhibited monolayer adsorption processes, that is, exothermic processes that occur spontaneously at low temperatures, which were analyzed based on the adsorption isotherms, adsorption kinetics, and thermodynamics model fittings. The presence of PSS enables cationic methylene blue dye to adsorb to the anionic chitosan structure via electrostatic interaction between the sulfonic group and the dye molecule. The maximum adsorption capacity of PSS-incorporated chitosan beads achieved 42.21 mg/g, as calculated from the Langmuir adsorption isotherm. Finally, the PSS-incorporated chitosan beads demonstrated good regeneration with different types of reagents, especially using sodium hydroxide as a regeneration reagent. With the use of sodium hydroxide regeneration of this adsorbent material, a continuous adsorption setup also demonstrated that PSS-incorporated chitosan beads can be reused for methylene blue adsorption for up to three cycle processes.

Macro-Size Regenerated Cellulose Fibre Embedded with Graphene Oxide with Antibacterial Properties.

Macro-size regenerated cellulose fibres (RCFs) with embedded graphene oxide (GO) were fabricated by dissolving cellulose in a pre-cooled sodium hydroxide (NaOH)/urea solution and regenerated in sulphuric acid (H2SO4) coagulant. Initially, GO was found to disperse well in the cellulose solution due to intercalation with the cellulose; however, this cellulose-GO intercalation was disturbed during the regeneration process, causing agglomeration of GO in the RCF mixture. Agglomerated GO was confirmed at a higher GO content under a Dino-Lite microscope. The crystallinity index (CrI) and thermal properties of the RCFs increased with increasing GO loadings, up to 2 wt.%, and reduced thereafter. Cellulose-GO intercalation was observed at lower GO concentrations, which enhanced the crystallinity and thermal properties of the RCF-GO composite. It was shown that the GO exhibited antibacterial properties in the RCF-GO composite, with the highest bacterial inhibition against E. coli and S. aureus.

Chitosan Fibers Loaded with Limonite as a Catalyst for the Decolorization of Methylene Blue via a Persulfate-Based Advanced Oxidation Process.

Wastewater generated from industries seriously impacts the environment. Conventional biological and physiochemical treatment methods for wastewater containing organic molecules have some limitations. Therefore, identifying other alternative methods or processes that are more suitable to degrade organic molecules and lower chemical oxygen demand (COD) in wastewater is necessary. Heterogeneous Fenton processes and persulfate (PS) oxidation are advanced oxidation processes (AOPs) that degrade organic pollutants via reactive radical species. Therefore, in this study, limonite powder was incorporated into porous regenerated chitosan fibers and further used as a heterogeneous catalyst to decompose methylene blue (MB) via sulfate radical-based AOPs. Limonite was used as a heterogeneous catalyst in this process to generate the persulfate radicals (SO4-·) that initiate the decolorization process. Limonite-chitosan fibers were produced to effectively recover the limonite powder so that the catalyst can be reused repeatedly. The formation of limonite-chitosan fibers viewed under a field emission scanning electron microscope (FESEM) showed that the limonite powder was well distributed in both the surface and cross-section area. The effectiveness of limonite-chitosan fibers as a catalyst under PS activation achieved an MB decolorization of 78% after 14 min. The stability and reusability of chitosan-limonite fibers were evaluated and measured in cycles 1 to 10 under optimal conditions. After 10 cycles of repeated use, the limonite-chitosan fiber maintained its performance up to 86%, revealing that limonite-containing chitosan fibers are a promising reusable catalyst material.

Green synthesis and characterization of UKMRC-8 rice husk-derived mesoporous silica nanoparticle for agricultural application.

Agriculture plays a crucial role in safeguarding food security, more so as the world population increases gradually. A productive agricultural system is supported by seed, soil, fertiliser and good management practices. Food productivity directly correlates to the generation of solid wastes and utilization of agrochemicals, both of which negatively impact the environment. The rice and paddy industry significantly adds to the growing menace of waste management. In low and middle-income countries, rice husk (RH) is an underutilized agro-waste discarded in landfills or burned in-situ. RH holds enormous potential in the development of value-added nanomaterials for agricultural applications. In this study, a simple and inexpensive sol-gel method is described to extract mesoporous silica nanoparticles (MSNs) from UKMRC8 RH using the bottom-up approach. RHs treated with hydrochloric acid were calcinated to obtain rice husk ash (RHA) with high silica purity (> 98% wt), as determined by the X-ray fluorescence analysis (XRF). Calcination at 650 °C for four hours in a box furnace yielded RHA that was devoid of metal impurities and organic matter. The X-ray diffraction pattern showed a broad peak at 2θ≈20-22 °C and was free from any other sharp peaks, indicating the amorphous property of the RHA. Scanning electron micrographs (SEM) showed clusters of spherically shaped uniform aggregates of silica nanoparticles (NPs) while transmission electron microscopy analysis indicated an average particle size of < 20 nm. Besides Energy Dispersive X-Ray which validated the chemical constituent of the silica NPs, the Fourier transform infrared (FT-IR) spectra showed peaks at 796.4 cm-1 and 1052 cm-1 corresponding to O-Si-O symmetric stretching vibration and O-Si-O asymmetric stretching, respectively. The Brunauer-Emmet-Teller (BET) analysis indicated an average pore size = 8.5 nm while the specific surface area and the pore volume were 300.2015 m2/g and 0.659078 cm3/g, respectively. In conclusion, agrowaste-derived MSN was synthesized using a simple and economical sol-gel method without the addition of surfactant reagents for controlled formation at the structural level. Owing to the MSNs' excellent physical properties, the method established herein, could be used singly (without any modifications) for the functionalization of a myriad of agrochemicals.

Thermally Treated Berberine-Loaded SA/PVA/PEO Electrospun Microfiber Membranes for Antibacterial Wound Dressings.

This study aimed to develop a safe and advanced antibacterial material of electrospun microfiber membranes (MFMs) for wound dressings. Combinations of several materials were investigated; thermal treatment and electrospinning techniques were used to form the best quality of MFMs to suit its end applications. By comparing the fiber morphology, diameter changes, and fracture strength, the suitable ratio of raw materials and thermal treatment were obtained before and after adding Trition X-100 as a surfactant for MFMs of sodium alginate/polyvinyl alcohol/polyethylene oxide (SA/PVA/PEO). The electrospinning solution was mixed with berberine as an antibacterial substance; meanwhile, calcium chloride (CaCl2) was used as the crosslinking agent. The antibacterial properties, water dissolution resistance, water content, and fracture strength were thoroughly investigated. The results showed that the antibacterial rates of MFMs with different mass fractions of berberine (0, 3, and 5 wt.%) to Escherichia coli (E. coli) were 14.7, 92.9, and 97.2%, respectively. The moisture content and fracture strength of MFMs containing 5 wt.% berberine were 72.0% and 7.8 MPa, respectively. In addition, the produced MFMs embodied great water dissolution resistance. Berberine-loaded SA/PVA/PEO MFMs could potentially serve as an antibacterial wound dressing substrate with low cost and small side effects.

Different Preparation Method of Nanocellulose from Macaranga gigantea and Its Preliminary Study on Packaging Film Potential

Nanocellulose is a versatile cellulosic nanomaterial that can be used in many application areas. Applying different preparation strategies leads to different types of nanocellulose. In this study, nanocrystalline cellulose (NCC) and nanofibrillated cellulose (NFC) were prepared from lesser known wood species, viz., Macaranga gigantea, using sulfuric acid hydrolysis and enzymatic pretreatment with ultrafine grinding approaches, respectively. The respective nanocellulose was characterized by means of Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD) analysis, thermogravimetric analysis (TGA), atomic force microscopy (AFM). It was then converted into a thin film to assess its performance which includes tensile test, transparency, air permeance, water vapor transmission rate (WVTR), and water vapor permeability (WVP) properties. NCC and NFC produced from the raw material of Macaranga had average widths of 6.38 ± 3.92 nm and 13.17 ± 12.71 nm, respectively. Peaks in FTIR spectra showed the conversion of Macaranga wood to nanocellulose by the presence of cellulose fingerprint as well as absence of lignin and hemicellulose after alkaline treatment. The successful conversion was also supported by XRD analysis which displayed the increased crystallinity value from 54% to 70%. TGA decomposition pattern at 200-490 °C revealed the thermal stability of the samples. The thin film produced from nanocelluloses had WVTR values of 4.58 and 12.14 g/(day·m2) for NFC and NCC, respectively, comparable to those of films from polyester and oriented polypropylene. Nanocellulose-based thin film has the potential to be used as sustainable and biodegradable packaging.

Hydrogel Application in Urban Farming: Potentials and Limitations-A Review.

Urban agriculture plays a vital role in ensuring the self-sufficiency of a great variety of fresh vegetables and nutrients. It promotes a sustainable food system as well as reducing the dependency on imports for the growing population. Urban farming has made it possible for agriculture practices to be implemented anywhere at any time in a sophisticated way. Hydrogel has been introduced in urban agriculture in the past few decades. However, the application of hydrogel in urban agriculture is still being explored in terms of hydrogel types, structure, physical and chemical properties, change due to external factors, and its suitability for different plant species. This review discusses the potentials and limitations of hydrogel in different application conditions. We present the state of knowledge on hydrogel production and crosslinking methods, hydrogel characteristics, water absorption and release mechanisms of hydrogel, hydrogel advantages and limitations, and current and future applications in urban farming.

Drying Regimes on Regenerated Cellulose Films Characteristics and Properties.

Abundant water content and its interaction with cellulose macromolecules through hydrogen bonding engenders a complex drying process, the circumstances of which have not yet been unveiled. For instance, excessive drying on regenerated cellulose membranes (RCM) causes cracking and severe shrinking, affecting the produced regenerated cellulose film (RCF). Thus, mathematical models in estimating the drying kinetics and required energy to dry RCM are necessary. This study evaluated two drying techniques of oven drying and infrared (IR) drying on RCM at different temperatures of 50-80 °C. Five mathematical models were used, namely Newton, Page, Handreson-Pabis, logarithmic, and Wang-Singh, to adjust the obtained experimental data and were statistically validated using ANOVA to review their effect on the quality of the produced RCF. A logarithmic model and a Wang-Singh model were the best models for oven drying and IR drying of RCM, respectively. It was found that the physical property of the RCF was similar to all drying types. Meanwhile, for mechanical properties, the high temperature of oven drying affected the tensile properties of RCF compared with IR drying. This study is beneficial by approximating the drying kinetics of RCM and defining appropriate drying conditions, which controls the quality of its predictive physical and mechanical properties.

Mechanical Properties and Water Absorption Capacity of Hybrid GFRP Composites.

Hybrid glass fibre reinforced polymer (GFRP) composites have been used for decades in various engineering applications. However, it has a drawback with its application in marine/flood environments due to a lack of water resistance and frail mechanical stability. Floods have been considered one of the most periodic hazards that could hit urban areas, due to climate change. The present paper aims to address this gap and to investigate the mechanical properties (tensile, compressive, and flexural strength) and water absorption capacity of hybrid GFRP composite comprising woven E-glass fabric and epoxy resin, various reinforcing materials (kenaf and coconut fibres), and various filler materials (fly ash, nano-silica, and calcium carbonate (CaCO3). The composites with 30 wt.% GFRP, 50 wt.% resin, 15 wt.% fly ash, 5 wt.% CaCO3, 10 wt.% GFRP, 60 wt.% resin, and 30 wt.% fly ash showed the lowest water absorption property of 0.45%. The results revealed that the GFRP composite reinforced kenaf fibres with nano-silica, fly ash, and CaCO3 improved the water absorption resistance. At the same time, GFRP reinforced the coconut fibres with fly ash, and kenaf fibres with CaCO3 showed no favourable impact on water absorption. The identification of a hybrid GFRP composite with various reinforcing materials and fillers would assist future developments with a more compatible, enhanced, and reliable water-resistant composite, specifically for structural applications in flood-prone areas.

Impact of Drying Regimes and Different Coating Layers on Carboxymethyl Cellulose Cross-Linked with Citric Acid on Cotton Thread Fibers for Wound Dressing Modification.

The oldest preservation techniques used are drying techniques, which are employed to remove moisture and prevent microorganisms' growths, prolonging a material's shelf life. This study evaluates the effects of drying methods on carboxymethyl cellulose (CMC) + citric acid (CA) coating layers on cotton threads. For this reason, cotton threads were washed and then coated with different layers of CMC cross-linked with CA, followed by drying using an oven (OD), infrared (IR), and a combination of oven + IR (OIR) drying methods at 65 °C. Our investigations revealed that CMC + CA yields a pliable biopolymer. The differences in drying regimes and coating layers of CMC + CA have a significant effect on the coated cotton thread strength and absorption capability. The study concluded that the IR drying regime is more effective to dry a single-layered cotton thread with a single layer of CMC + CA coating to enhance desirable properties for wound dressing modification.

Effect of Impregnated Phenolic Resins on the Cellulose Membrane for Polymeric Insulator.

In this study, a cellulose membrane (CM) was chemically treated with phenolic (PF) resin to improve its performance as a polymeric insulator. The CM was prepared from kenaf pulp, and the PF was synthesized from oil palm empty fruit (EFB) fibre. Four different concentrations of synthesized PF resin (5, 10, 15, and 20 wt.%) were impregnated under wet or dry conditions. Thermal analysis of the phenolic cellulose membrane (PCM) showed that the samples had good chemical interaction and compatibility. The PF uptake in the wet phenolic cellulose membrane (PCMW) was higher than in the dry phenolic cellulose membrane (PCMD). During the PF uptake, the CM underwent solvent exchange and absorption in wet and dry membranes, respectively. This difference also affected the crosslinking of PCM samples via the formation of methylene bridges. Due to the PF treatment, the PCM showed lower water absorption than CM. The PF concentrations also affect the surface roughness and electrical properties of PCM samples. These findings prove that PCM can be used as a renewable and green polymer electrical insulator.

Recent advancement in 3-D printing: nanocomposites with added functionality.

Three-Dimentional (3-D) printing is currently a popular printing technique that is used in many sectors. Potentially, this technology is expected to replace conventional manufacturing in the coming years. It is accelerating in gaining attention due to its design freedom where objects can be produced without imagination boundaries. The review presents a perspective on the application of 3-D printing application based on various fields. However, the ordinary 3-D printed products with a single type of raw often lack robustness leading to broken parts. Improving the mechanical property of a 3-D printed part is crucial for its applications in many fields. One of the promising solutions is to incorporate nanoparticles or fillers into the raw material. The review aims to provide information about the types of additive manufacturing. There are few types of raw materials can be used as foundation template in the printing, enhanced properties of the printed polymer nanocomposites with different types of nanoparticles as additives in the printing. The article reviews the advantages and disadvantages of different materials that are used as raw materials or base materials in 3-D printing. This can be a guideline for the readers to compare and analyse the raw materials prior to a decision on the type of material to be selected. The review prepares an overview for the researchers to choose the types of nanoparticles to be added in the printing of the products depending on the targeted application. With the added functionality of the 3-D polymer nanocomposites, it will help in widespread of the application of 3-D printing technology in various sector.

Regenerated Cellulose Products for Agricultural and Their Potential: A Review.

Cellulose is one of the most abundant natural polymers with excellent biocompatibility, non-toxicity, flexibility, and renewable source. Regenerated cellulose (RC) products result from the dissolution-regeneration process risen from solvent and anti-solvent reagents, respectively. The regeneration process changes the cellulose chain conformation from cellulose I to cellulose II, leads the structure to have more amorphous regions with improved crystallinity, and inclines towards extensive modification on the RC products such as hydrogel, aerogel, cryogel, xerogel, fibers, membrane, and thin film. Recently, RC products are accentuated to be used in the agriculture field to develop future sustainable agriculture as alternatives to conventional agriculture systems. However, different solvent types and production techniques have great influences on the end properties of RC products. Besides, the fabrication of RC products from solely RC lacks excellent mechanical characteristics. Thus, the flexibility of RC has allowed it to be homogenously blended with other materials to enhance the final products' properties. This review will summarize the properties and preparation of potential RC-based products that reflect its application to replace soil the plantation medium, govern the release of the fertilizer, provide protection on crops and act as biosensors.

Production of Rigid Polyurethane Foams Using Polyol from Liquefied Oil Palm Biomass: Variation of Isocyanate Indexes.

Development of polyurethane foam (PUF) containing bio-based components is a complex process that requires extensive studies. This work reports on the production of rigid PUFs from polyol obtained via liquefaction of oil palm empty fruit bunch (EFB) biomass with different isocyanate (NCO) indexes. The effect of the NCO index on the physical, chemical and compressive properties of the liquefied EFB-based PUF (EFBPUF) was evaluated. The EFBPUFs showed a unique set of properties at each NCO index. Foaming properties had affected the apparent density and cellular morphology of the EFBPUFs. Increasing NCO index had increased the crosslink density and dimensional stability of the EFBPUFs via formation of isocyanurates, which had also increased their thermal stability. Combination of both foaming properties and crosslink density of the EFBPUFs had influenced their respective compressive properties. The EFBPUF produced at the NCO index of 120 showed the optimum compressive strength and released the least toxic hydrogen cyanide (HCN) gas under thermal degradation. The normalized compressive strength of the EFBPUF at the NCO index of 120 is also comparable with the strength of the PUF produced using petrochemical polyol.

Electron-Beam Irradiation of the PLLA/CMS/ß-TCP Composite Nanofibers Obtained by Electrospinning.

Nanofibrous materials produced by electrospinning processes have potential advantages in tissue engineering because of their biocompatibility, biodegradability, biomimetic architecture, and excellent mechanical properties. The aim of the current work is to study the influence of the electron beam on the poly L-lactide acid/ carboxy-methyl starch/ß-tricalcium phosphate (PLLA/CMS/ß-TCP) composite nanofibers for potential applications as bone-tissue scaffolds. The composite nanofibers were prepared by electrospinning in the combination of 5% v/v carboxy-methyl starch (CMS) and 0.25 wt% of ß-TCP with the PLLA as a matrix component. The composites nanofibers were exposed under 5, 30, and 100 kGy of irradiation dose. The electron-beam irradiation showed no morphological damage to the fibers, and slight reduction in the water-contact angle and mechanical strength at the higher-irradiation doses. The chain scission was found to be a dominant effect; the higher doses of electron-beam irradiation thus increased the in vitro degradation rate of the composite nanofibers. The chemical interaction due to irradiation was indicated by the Fourier transform infrared (FTIR) spectrum and thermal behavior was investigated by a differential scanning calorimeter (DSC). The results showed that the electron-beam-induced poly L-lactide acid/carboxy-methyl starch/ß-tricalcium phosphate (PLLA/CMS/ß-TCP) composite nanofibers may have great potential for bone-tissue engineering.

Copper Nanowires as Highly Efficient and Recyclable Catalyst for Rapid Hydrogen Generation from Hydrolysis of Sodium Borohydride.

: Hydrogen (H2) is a clean energy carrier which can help to solve environmental issues with the depletion of fossil fuels. Sodium borohydride (NaBH4) is a promising candidate material for solid state hydrogen storage due to its huge hydrogen storage capacity and nontoxicity. However, the hydrolysis of NaBH4 usually requires expensive noble metal catalysts for a high H2 generation rate (HGR). Here, we synthesized high-aspect ratio copper nanowires (CuNWs) using a hydrothermal method and used them as the catalyst for the hydrolysis of NaBH4 to produce H2. The catalytic H2 generation demonstrated that 0.1 ng of CuNWs could achieve the highest volume of H2 gas in 240 min. The as-prepared CuNWs exhibited remarkable catalytic performance: the HGR of this study (2.7 × 1010 mL min-1 g-1) is ~3.27 × 107 times higher than a previous study on a Cu-based catalyst. Furthermore, a low activation energy (Ea) of 42.48 kJ mol-1 was calculated. Next, the retreated CuNWs showed an outstanding and stable performance for five consecutive cycles. Moreover, consistent catalytic activity was observed when the same CuNWs strip was used for four consecutive weeks. Based on the results obtained, we have shown that CuNWs can be a plausible candidate for the replacement of a costly catalyst for H2 generation.

An improved physico-mechanical performance of macropores membrane made from synthesized cellulose carbamate.

Under hydrothermal condition, kenaf cellulose carbamate (KCC) was synthesized using urea and kenaf core pulp (KCP) without catalyst and organic solvent. The KCC was prepared with various urea/KCP ratios (2:1, to 4:1 and 6:1) with the aid of autoclave and oil bath, whereas the regenerated KCC membranes were formed via solution casting method. The physical and thermal properties of KCC were studied. The urea/KCP ratio used in preparing KCC corresponds with the nitrogen percentage obtained in KCC. The formation of the regenerated KCC membranes could be confirmed by the existence of cellulose II through X-ray diffraction (XRD) study. As examined by Field emission scanning electron microscope (FESEM), the regenerated KCC membranes possessed the greater pore size structures at higher urea concentration. Mechanical results showed the tensile strength and modulus of regenerated KCC membranes have improved up to 43.4% and 76.9%, respectively, as compared to native KCP membrane. It can be concluded from the findings that synthesizing KCC and its membranes with improved mechanical properties has broad prospects for potential industrial applications such as biomembranes and packaging materials.

Interconnected macropores cryogel with nano-thin crosslinked network regenerated cellulose.

Dissolved oil palm empty fruit bunch cellulose (EFBC) and sodium carboxymethylcellulose (NaCMC) were chemically crosslinked with epichlorohydrin (ECH) to generate designated hydrogel. After swelling process in distilled water, the swollen hydrogel was frozen and freeze-dried to form cryogel. The swelling phenomenon of hydrogel during the absorption process gave substantial effects on thinning of crosslinked network wall, pore size and volume, steadiness of cryogel skeletal structure, and re-swelling of cryogel. The swelling effects on hydrogel were confirmed via microscopic study using variable pressure scanning electron microscope (VPSEM). From the retrieved VPSEM images, nano-thin crosslinked network wall of 24.31 ± 1.97 nm and interconnected pores were observed. As a result, the amount of water, the swelling degree, and the freeze-drying process indirectly affected the VPSEM images that indicated pore size and volume, formation of interconnected pores, and re-swelling of cryogel. This study determined the intertwined factors that affected both hydrogel and cryogel properties by investigating the swelling phenomenon and its ensuing effects.