Perovskite solar cells (PSCs) are attracting widespread research and attention as highly promising candidates in the field of electronic photovoltaics owing to their exceptional power conversion efficiency (PCE). However, rigid or flexible PSCs still face challenges in preparing full-coverage and low-defect perovskite films, as well as achieving highly reproducible and highly stable devices. Herein, a multifunctional additive 2-aminoethyl hydrogen sulfate (AES) is designed to regulate the film crystallization and thereby form flat and pinhole-free perovskite films. It is found that the introduction of AES can effectively passivate defects, restrain charge carrier recombination, and then achieve a higher fill factor. As seen with grazing incidence wide-angle X-ray scattering (GIWAXS), this approach does not affect the crystal orientation distribution. It is observed that AES addition shows a universality across different perovskite components since the PCE is improved up to 20.7% for FA0.97MA0.03Pb(I0.97Br0.03)3-AES, 22.85% for Cs0.05FA0.95PbI3-AES, 22.23% for FAPbI2.7Br0.3-AES, and 23.32% for FAPI-AES rigid devices. Remarkably, the non-encapsulated flexible Cs0.05 (FA0.85MA0.15)0.95Pb(I0.85Br0.15)3 device with AES additive delivers a PCE of 20.1% and maintains over 97% of its initial efficiency under ambient conditions (25 ± 5% relative humidity) over 2280 h of aging.
Electrocatalytic oxidation of alcohols using heterogeneous catalysts is a promising aqueous, energy-efficient and environmentally friendly approach, especially for coupling different alcohols to prolong the carbon chain via co-oxidation. Precisely regulating critical steps to tailor electrode materials and electrolyte composition is key to selectively coupling alcohols for targeted synthesis. However, selectively coupling different alcohols remains challenging due to the lack of effective catalyst and electrolyte design promoting specific pathways. Herein, we demonstrate a paired electrolysis strategy for combining anodic oxidative coupling of ethanol (EtOH) and benzyl alcohol (PhCH2OH) to synthesize cinnamaldehyde (CAL) and cathodic ammonia production. The strategies involve: (i) utilizing the salt-out effect to balance selective oxidation and coupling rates; (ii) developing platinum-loaded nickel hydroxide electrocatalysts to accelerate intermediate coupling kinetics; (iii) introducing thermodynamically favorable nitrate reduction at the cathode to improve coupling selectivity by avoiding hydrogenation of products while generating valuable ammonia instead of hydrogen. We achieved 85% coupling selectivity and 278 µmol/h NH3 productive rate at 100 mA/cm2 with a low energy input (â¼1.63 V). The membrane-free, low energy, scalable approach with a wide substrate scope highlights promising applications of this methodology. This work advances heterogeneous electrocatalytic synthesis through rational design principles that integrate anodic oxidative coupling with cathodic nitrate reduction reactions, having synergistic effects on efficiency and selectivity.
Preventing the deactivation of noble metal-based catalysts due to self-oxidation and poisonous adsorption is a significant challenge in organic electro-oxidation. In this study, we employ a pulsed potential electrolysis strategy for the selective electrocatalytic oxidation of glycerol to glyceric acid over a Pt-based catalyst. In situ Fourier-transform infrared spectroscopy, quasi-in situ X-ray photoelectron spectroscopy, and finite element simulations reveal that the pulsed potential could tailor the catalyst's oxidation and surface micro-environment. This prevents the overaccumulation of poisoning intermediate species and frees up active sites for the re-adsorption of OH adsorbate and glycerol. The pulsed potential electrolysis strategy results in a higher glyceric acid selectivity (81.8%) than constant-potential electrocatalysis with 0.7 VRHE (37.8%). This work offers an efficient strategy to mitigate the deactivation of noble metal-based electrocatalysts.
The electrocatalytic oxidation of 5-hydroxymethylfurfural (HMF) provides a feasible way for utilization of biomass resources. However, how to regulate the selective synthesis of multiple value-added products is still a great challenge. The cobalt-based compound is a promising catalyst due to its direct and indirect oxidation properties, but its weak adsorption capacity restricts its further development. Herein, by constructing AgâCo(OH)2 heterogeneous catalyst, the efficient and selective synthesis of 5-hydroxymethyl-2-furanoic acid (HMFCA) and 2,5-furan dicarboxylic acid (FDCA) at different potential ranges are realized. Based on various physical characterizations, electrochemical measurements, and density functional theory calculations, it is proved that the addition of Ag can effectively promote the oxidation of aldehyde group to a carboxyl group, and then generate HMFCA at low potential. Moreover, the introduction of Ag can activate cobalt-based compounds, thus strengthening the adsorption of organic molecules and OH- species, and promoting the formation of FDCA. This work achieves the selective synthesis of two value-added chemicals by one tandem catalyst and deeply analyzes the adsorption enhancement mechanism of the catalyst, which provides a powerful guidance for the development of efficient heterogeneous catalysts.
Aqueous electrochemical coupling reactions, which enable the green synthesis of complex organic compounds, will be a crucial tool in synthetic chemistry. However, a lack of informed approaches for screening suitable catalysts is a major obstacle to its development. Here, we propose a pioneering electrochemical reductive coupling reaction toward direct electrosynthesis of oxime from NOx and aldehyde. Through integrating experimental and theoretical methods, we screen out the optimal catalyst, i.e., metal Fe catalyst, that facilitates the enrichment and C-N coupling of key reaction intermediates, all leading to high yields (e.g., â¼99% yield of benzaldoxime) for the direct electrosynthesis of oxime over Fe. With a divided flow reactor, we achieve a high benzaldoxime production of 22.8 g h-1 gcat-1 in â¼94% isolated yield. This work not only paves the way to the industrial mass production of oxime via electrosynthesis but also offers references for the catalyst selection of other electrochemical coupling reactions.
The instability of perovskite absorbers under various environmental stressors is the most significant obstacle to widespread commercialization of perovskite solar cells. Herein, we study the evolution of crystal structure and microstrain present in naked triple-cation mixed CsMAFA-based perovskite films under heat, UV, and visible light (1 Sun) conditions by grazing-incidence wide-angle X-ray scattering (GIWAXS). We find that the microstrain is gradient distributed along the surface normal of the films, decreasing from the upper surface to regions deeper within the film. Moreover, heat, UV, and visible light treatments do not interfere with the crystalline orientations within annealed polycrystalline films. However, when subjected to heat, the naked perovskite films exhibit a rapid component decomposition, induced by phase separation and ion migration. Conversely, under exposure to UV and 1 Sun light soaking, the naked perovskite films undergo a self-optimization structure evolution during degradation and develop into smoother films with reduced surface potential fluctuations.
Owing to outstanding performances, nickel-based electrocatalysts are commonly used in electrochemical alcohol oxidation reactions (AORs), and the active phase is usually vacancy-rich nickel oxide/hydroxide (NiOx Hy ) species. However, researchers are not aware of the catalytic role of atom vacancy in AORs. Here, we study vacancy-induced catalytic mechanisms for AORs on NiOx Hy species. As to AORs on oxygen-vacancy-poor ß-Ni(OH)2 , the only redox mediator is electrooxidation-induced electrophilic lattice oxygen species, which can only catalyze the dehydrogenation process (e.g., the electrooxidation of primary alcohol to carboxylic acid) instead of the C-C bond cleavage. Hence, vicinal diol electrooxidation reaction involving the C-C bond cleavage is not feasible with oxygen-vacancy-poor ß-Ni(OH)2 . Only through oxygen vacancy-induced adsorbed oxygen-mediated mechanism, can oxygen-vacancy-rich NiOx Hy species catalyze the electrooxidation of vicinal diol to carboxylic acid and formic acid accompanied with the C-C bond cleavage. Crucially, we examine how vacancies and vacancy-induced catalytic mechanisms work during AORs on NiOx Hy species.
Solution processing of hybrid perovskite semiconductors is a highly promising approach for the fabrication of cost-effective electronic and optoelectronic devices. However, challenges with this approach lie in overcoming the controllability of the perovskite film morphology and the reproducibility of device efficiencies. Here, a facile and practical aging treatment (AT) strategy is reported to modulate the perovskite crystal growth to produce sufficiently high-quality perovskite thin films with improved homogeneity and full-coverage morphology. The resulting AT-films exhibit fewer defects, faster charge carrier transfer/extraction, and suppressed non-radiative recombination compared with reference. The AT-devices achieve a noticeable improvement in the reproducibility, operational stability, and photovoltaic performance of devices, with the average efficiency increased by 16%. It also demonstrates the feasibility and scalability of AT strategy in optimizing the film morphology and device performance for other perovskite components including MAPbI3 , (MAPbBr3 )15 (FAPbI3 )85 , and Cs0.05 (MAPbBr3 )0.17 (FAPbI3 )0.83 . This method opens an effective avenue to improve the quality of perovskite films and photovoltaic devices in a scalable and reproducible manner.
Conventional designing principal of electrocatalyst is focused on the electronic structure tuning, on which effectively promotes the electrocatalysis. However, as a typical kind of electrode-electrolyte interface reaction, the electrocatalysis performance is also closely dependent on the electrocatalyst interfacial micro-environment (IME), including pH, reactant concentration, electric field, surface geometry structure, hydrophilicity/hydrophobicity, etc. Recently, organic electro-oxidation reaction (OEOR), which simultaneously reduces the anodic polarization potential and produces value-added chemicals, has emerged as a competitive alternative to oxygen evolution reaction, and the role IME played in OEOR is receiving great interest. Thus, this article provides a timely review on IME and its applications toward OEOR. In this review, the IME for conventional gas-involving reactions, as a contrast, is first presented, and then the recent progresses of IME toward diverse typical OEOR are summarized; especially, some representative works are thoroughly discussed. Additionally, cutting-edge analytical methods and characterization techniques are introduced to comprehensively understand the role IME played in OEOR. In the last section, perspectives and challenges of IME regulation for OEOR are shared.
5-Hydroxymethylfurfural (HMF), one of the essential C6 biomass derivatives, has been deeply investigated in electrocatalytic reduction upgrading. Nevertheless, the high product selectivity and rational design strategy of electrocatalysts for electrocatalytic HMF reduction is still a challenge. Here, a high selective electro-reduction of HMF to dimethylfuran (DMF) on palladium (Pd) single atom loaded on titanium dioxide (Pd SA/TiO2 ) via hydrogen spillover and adsorption configuration adjustment in neutral electrolytes is achieved. Combining density functional theory calculations and in situ characterization, it is revealed that Pd single atom could weaken the interaction between Pd atoms and adsorbed hydrogen (*H) to promote the *H spillover for increasing *H coverage on the surface and maintain the tilted adsorption configuration to activate CâO bond; thus the selectivity of DMF on Pd SA/TiO2 increases to 90.33%. Besides, it is elaborated that low *H coverage on TiO2 favors the formation of bis(hydroxymethyl)hydro-furoin (BHH), and the flat adsorption configuration of HMF on Pd nanoparticles benefits to form 2,5-dihydroxymethylfuran (DHMF). This work provides a promising approach for modifying electrocatalysts to realize the selective electroreduction of HMF to value-added products.
Alanine is widely employed for synthesizing polymers, pharmaceuticals, and agrochemicals. Electrocatalytic coupling of biomass molecules and waste nitrate is attractive for the nitrate removal and alanine production under ambient conditions. However, the reaction efficiency is relatively low due to the activation of the stable substrates, and the coupling of two reactive intermediates remains challenging. Herein, we realize the integrated tandem electrochemical-chemical-electochemical synthesis of alanine from the biomass-derived pyruvic acid (PA) and waste nitrate (NO3 - ) catalyzed by PdCu nano-bead-wires (PdCu NBWs). The overall reaction pathway is demonstrated as a multiple-step catalytic cascade process via coupling the reactive intermediates NH2 OH and PA on the catalyst surface. Interestingly, in this integrated tandem electrochemical-chemical-electrochemical catalytic cascade process, Cu facilitates the electrochemical reduction of nitrate to NH2 OH intermediates, which chemically couple with PA to form the pyruvic oxime, and Pd promotes the electrochemical reduction of pyruvic oxime to the desirable alanine. This work provides a green strategy to convert waste NO3 - to wealth and enriches the substrate scope of renewable biomass feedstocks to produce high-value amino acids.
Aqueous organic electrosynthesis such as nucleophile oxidation reaction (NOR) is an economical and green approach. However, its development has been hindered by the inadequate understanding of the synergy between the electrochemical and non-electrochemical steps. In this study, we unravel the NOR mechanism for the primary alcohol/vicinal diol electrooxidation on NiO. Thereinto, the electrochemical step is the generation of Ni3+-(OH)ads, and the spontaneous reaction between Ni3+-(OH)ads and nucleophiles is an electrocatalyst-induced non-electrochemical step. We identify that two electrophilic oxygen-mediated mechanisms (EOMs), EOM involving hydrogen atom transfer (HAT) and EOM involving C-C bond cleavage, play pivotal roles in the electrooxidation of primary alcohol to carboxylic acid and the electrooxidation of vicinal diol to carboxylic acid and formic acid, respectively. Based on these findings, we establish a unified NOR mechanism for alcohol electrooxidation and deepen the understanding of the synergy between the electrochemical and non-electrochemical steps during NOR, which can guide the sustainable electrochemical synthesis of organic chemicals.
The low-potential furfural oxidation reaction (FFOR) on a Cu-based electrocatalyst can produce H2 at the anode, thereby providing a bipolar H2 production system with an ultralow cell voltage. However, the intrinsic activity and stability of the Cu-based electrocatalyst for the FFOR remain unsatisfactory for practical applications. This study investigates the correlation between the valence state and the adsorption behavior of the Cu-based electrocatalyst in furfural oxidation. Cu0 is the adsorption site with low intrinsic activity. Cu+ , which exists in the form of Cu(OH)ads in alkaline electrolytes, has no adsorption ability but can improve the performance of Cu0 by promoting the adsorption of FF. Moreover, a mixed-valence Cu-based electrocatalyst (MV Cu) with high intrinsic activity and stability is prepared electrochemically. With the MV Cu catalyst, the assembled dual-side H2 production electrolyzer has a low electricity requirement of only 0.24 kWh mH2 -3 at an ultralow cell voltage of 0.3 V, and it exhibits sufficient stability. This study not only correlates the valence state with the adsorption behavior of the Cu-based electrocatalyst for the low-potential FFOR with anodic H2 production but also reveals the mechanism of deactivation to provide design principles for Cu-based electrocatalysts with satisfactory stability.
Synthesis of cyclohexanone oxime via the cyclohexanone-hydroxylamine process is widespread in the caprolactam industry, which is an upstream industry for nylon-6 production. However, there are two shortcomings in this process, harsh reaction conditions and the potential danger posed by explosive hydroxylamine. In this study, we presented a direct electrosynthesis of cyclohexanone oxime using nitrogen oxides and cyclohexanone, which eliminated the usage of hydroxylamine and demonstrated a green production of caprolactam. With the Fe electrocatalysts, a production rate of 55.9â g h-1 gcat -1 can be achieved in a flow cell with almost 100 % yield of cyclohexanone oxime. The high efficiency was attributed to their ability of accumulating adsorbed hydroxylamine and cyclohexanone. This study provides a theoretical basis for electrocatalyst design for C-N coupling reactions and illuminates the tantalizing possibility to upgrade the caprolactam industry towards safety and sustainability.
Ni-based materials are auspicious electrocatalysts for 5-hydroxymethylfurfural oxidation reaction (HMFOR), including the adsorption and conversion of HMF and OHad on the electrocatalyst surface. However, the intrinsic HMFOR activity of Ni-based catalysts is far from satisfactory due to the weak adsorption of HMF and OHad species. Herein, a set of PtxNi100-x bundle nanowires (NWs) were prepared for HMFOR, which enables a low onset-potential and large current density. Operando methods reveal that Pt modulates the redox property of Ni in PtNi NWs and accelerates the oxidation of Ni2+-OH to Ni3+-O species during HMFOR. Moreover, the adsorption studies demonstrate the synergetic roles of Pt and Ni in enhancing the HMFOR activity by forming Pt-O-Ni bonds. In detail, Ni atoms modulate the d band of Pt to alter the adsorption behavior of HMF. Pt atoms promote the adsorption of OHad on Ni sites. This work provides design principles for HMFOR electrocatalysts by modulating the adsorption behaviors of organic molecules and OHad.
Nanowires , Adsorption , Biomass , Oxidation-Reduction
Electrocatalytic conversion of biomass platform chemicals to jet fuel precursors is a promising approach to alleviate the energy crisis caused by the excessive exploitation and consumption of non-renewable fossil fuels. However, an aqueous electrolyte has been rarely studied. In this study, we demonstrate an anodic electrocatalysis route for producing jet fuel precursors from biomass platform chemicals on Ni-based electrocatalysts in an aqueous electrolyte at room temperature and atmosphere pressure. The desired product exhibited high selectivity for the jet fuel precursor (95.4%) and an excellent coulombic efficiency of 210%. A series of in situ characterizations demonstrated that Ni2+ species were the active sites for the coupling process. In addition, the coupling reaction could be achieved by generating radical cations and inhibiting the side reaction. First, the electrochemical process could activate the furfural (FF) molecule and generate radical cations, resulting in an average of 2.0 times chain propagation. The levulinic acid (LA) molecules played a vital role in the coupling reaction. The adsorption strength of LA on Ni3N was higher than that of FF, which could inhibit the side reaction (the oxidation of FF) and achieve high selectivity. Meanwhile, the LA molecules were adsorbed on the Ni3N surface and then disrupted the formation of Ni3+ species, thus favoring the coupling reaction. This work demonstrates an efficient route to produce jet fuel precursors directly from biomass platform chemicals and provides a comprehensive understanding of the anodic coupling process.
Furaldehyde , Water , Biomass , Water/chemistry , Oxidation-Reduction
Formate can be synthesized electrochemically by CO2 reduction reaction (CO2RR) or formaldehyde oxidation reaction (FOR). The CO2RR approach suffers from kinetic-sluggish oxygen evolution reaction at the anode. To this end, an electrochemical system combining cathodic CO2RR with anodic FOR was developed, which enables the formate electrosynthesis at ultra-low voltage. Cathodic CO2RR employing the BiOCl electrode in H-cell exhibited formate Faradaic efficiency (FE) higher than 90% within a wide potential range from - 0.48 to - 1.32 VRHE. In flow cell, the current density of 100 mA cm-2 was achieved at - 0.67 VRHE. The anodic FOR using the Cu2O electrode displayed a low onset potential of - 0.13 VRHE and nearly 100% formate and H2 selectivity from 0.05 to 0.35 VRHE. The CO2RR and FOR were constructed in a flow cell through membrane electrode assembly for the electrosynthesis of formate, where the CO2RR//FOR delivered an enhanced current density of 100 mA cm-2 at 0.86 V. This work provides a promising pair-electrosynthesis of value-added chemicals with high FE and low energy consumption.
Selective electrocatalytic oxidation of alcohols to value-added aldehydes has attracted increasing attention. However, due to its higher reactivity than alcohol, the aldehyde is easily over-oxidized to acid in alkaline electrolytes. Herein we realize the selective electrooxidation of alcohol to aldehyde on NiO by tuning the local microenvironment to salt out the aldehyde from the reaction system. The origin of the high selectivity was found to be the inhibition of the hydration of aldehydes, which is the result of the decreased alkalinity and the increased cation and substrate concentration. This strategy could salt out the aldehyde at the gas|electrolyte interface from the electrooxidation of alcohol with 100 % selectivity and be easily extended to other selective oxidation reactions, such as 5-hydroxymethyl furfural (HMF) to 2,5-furandicarboxaldehyde (DFF) and amine to an imine.
