Bis-EMA/Bis-GMA ratio effects on resin-properties and impregnated fiber-bundles.

OBJECTIVES: To evaluate the effect of different ratios of Bis-EMA/Bis-GMA resin mixtures on the inherent viscosity and curing-related properties: including degree of cure (DC%), shrinkage strain, Knoop micro-hardness (KH) and flexural strength of resin-impregnated fiber-bundles. METHODS: Bis-EMA/Bis-GMA monomers were mixed (by weight) in the following ratios: M1 = 30 %/70 %, M2 = 50 %/50 %, M3 = 70 %/30 %, and M4 = 100 %/0 %. Standard measurements were made of refractive index, viscosity, degree of conversion, shrinkage strain and Knoop hardness (KHN). For 60 % glass fiber-bundles impregnated with 40 % resin, three-point bending test for flexural strength and shrinkage strain were measured. Data were analyzed by One-way ANOVA and Bonferroni post-hoc tests (α = 0.05). RESULTS: For resin mixtures, increasing Bis-EMA proportion decreased refractive index (p < 0.05), and viscosity (p < 0.05), and increased monomer conversion (DC%), shrinkage strain and KHN (p < 0.05). DC% increased after 1 h for all resin mixtures. The shrinkage strain and flexural strength of resin-impregnated fiber-bundles reduced with increased Bis-EMA. SIGNIFICANCE: Monomeric mixtures with highest amounts of Bis-EMA showed enhancement in several clinically-relevant properties and polymerization of respective resin-impregnated glass fibers. This makes them potential candidates for impregnating glass fibers in fiber-reinforced restorations.

Effect of Bleaching Agents on Composite Resins with and without Bis-GMA: An In Vitro Study.

The objective was to evaluate the change in color, hardness, and roughness produced by carbamide peroxide (CP) at two different concentrations on two resins. The 16% or 45% CP was applied to 66 resin discs with and without Bis-GMA. The color was measured with a spectrophotometer, and ΔEab and ΔE00 were calculated. Microhardness tester and SEM were used. In both composites, the a* and b* coordinates tended to be red and yellow, respectively, and were significant in the Bis-GMA group (p < 0.05). The ΔEab and ΔE00 were higher in the composite with Bis-GMA, regardless of the treatment received (p < 0.05). The microhardness was reduced in both composites regardless of the PC concentration compared to the control (p < 0.05). The 45% CP reduced the microhardness in the resin group with Bis-GMA compared to 16% CP (p < 0.001) but was not significant in the resin without Bis-GMA (p = 1). An increase in roughness was directly proportional to the concentration of CP, and it was more notable in the composite without Bis-GMA. The composite with Bis-GMA showed a greater tendency to darken than the one without Bis-GMA. The surface hardness of the composite was reduced in both composites and was not influenced by CP concentration in the composite without Bis-GMA. Bleaching is a common procedure nowadays. It is important to know how CP affects composites to establish a prognosis of the treatments in terms of color change, roughness, and hardness.

Investigation of Mechanical Properties of Polymer-Infiltrated Tetrapodal Zinc Oxide in Different Variants.

The aim of this study was to evaluate the influence of weight ratio, the shape of the precursor particles, and the application of a phosphate-monomer-containing primer on the mechanical properties of polymer infiltrated ceramic networks (PICNs) using zinc oxide. Two different types of zinc oxide particles were used as precursors to produce zinc oxide networks by sintering, each with two different densities resulting in two different weight ratios of the PICNs. For each of these different networks, two subgroups were built: one involving the application of a phosphate-monomer-containing primer prior to the infiltration of Bis-GMA/TEGDMA and one without. Elastic modulus and flexural strength were determined by using the three-point bending test. Vertical substance loss determined by the chewing simulation was evaluated with a laser scanning microscope. There was a statistically significant influence of the type of precursor particles on the flexural strength and in some cases on the elastic modulus. The application of a primer lead to a significant increase in the flexural strength and in most cases also in the elastic modulus. A higher weight ratio of zinc oxide led to a significantly higher elastic modulus. Few statistically significant differences were found for the vertical substance loss. By varying the shape of the particles and the weight fraction of zinc oxide, the mechanical properties of the investigated PICN can be controlled. The use of a phosphate-monomer-containing primer strengthens the bond between the infiltrated polymer and the zinc oxide, thus increasing the strength of the composite.

Level of BPA contamination in resin composites determines BPA release.

OBJECTIVES: Resin composites may release bisphenol A (BPA) due to impurities present in the monomers. However, there is a lack of knowledge regarding the leaching characteristics of BPA from resin composites. Therefore, experimental resin composites were prepared with known amounts of BPA. The objective of this study was (1) to determine which amount of BPA initially present in the material leaches out in the short term and, (2) how this release is influenced by the resin composition. METHODS: BPA (0, 0.001, 0.01, or 0.1 wt%) was added to experimental resin composites containing 60 mol% BisGMA, BisEMA(3), or UDMA, respectively, as base monomer and 40 mol% TEGDMA as diluent monomer. Polymerized samples (n = 5) were immersed at 37 °C for 7 days in 1 mL of water, which was collected and refreshed daily. BPA release was quantified with UPLC-MS/MS after derivatization with pyridine-3-sulfonyl chloride. RESULTS: Between 0.47 to 0.67 mol% of the originally added BPA eluted from the resin composites after 7 days. Similar elution trends were observed irrespective of the base monomer. Two-way ANOVA showed a significant effect of the base monomer on BPA release, but the differences were small and not consistent. SIGNIFICANCE: The released amount of BPA was directly proportional to the quantity of BPA present in the resin composite as an impurity. BPA release was mainly diffusion-based, while polymer composition seemed to play a minor role. Our results underscore the importance for manufacturers only to use monomers of the highest purity in dental resin composites to avoid unnecessary BPA exposure in patients.

The impact of Bis-GMA free and Bis-GMA containing resin composite as posterior restoration on marginal integrity: a randomized controlled clinical trial.

BACKGROUND: There have been concerns surrounding the utilization of Bis-GMA, a type of bisphenol A (BPA) derivative, within the dental industry. The aim of this study was to compare the performance of bulk fill Bis-GMA-free resin composite class II restorations in respect of its marginal integrity in comparison to bulk fill Bis-GMA-containing resin composite class II restorations over a 12-month period in a parallel clinical trial utilizing a split-mouth, double-blind, randomized strategy. METHODS: 20 patients participated in this study. Each patient has received one pair of class II posterior restorations, Bis-GMA-free (Admira fusion x-tra), and Bis-GMA containing (x-tra fil) on each side of the mouth (split-mouth strategy), (n = 40). The restorations' marginal integrity was evaluated based on Ryge's criteria (modified USPHS) at baseline (after 1 week), as well as 1 month, 3 months, 6 months, 9 months, and after 12 months of follow-up by two calibrated examiners. The statistical analyses utilizing the Friedman and Wilcoxon tests, the significance level was adjusted to 0.05. RESULTS: Following the 12-month period, all patients attended the recall visits to evaluate the restorations. The Wilcoxon signed-rank and Friedman tests, revealed that both types of bulk fill had 100% of Alpha (A) scores at baseline and after 1 month with no significant statistical differences. After 3, 6, 9, and 12 months, both tested bulk fill restorations showed Bravo (B) score with Bis-GMA free 10% and 5% for Bis-GMA containing with no statistically significant difference (p ≤ 0.05) for clinical marginal integrity parameter in USPHS criteria. CONCLUSIONS: Bis-GMA-free resin composites demonstrated satisfactory, marginal integrity compared with Bis-GMA-containing resin composites within 12 months. TRIAL REGISTRATION: The protocol of the current study was registered at www. CLINICALTRIALS: gov , with the identification number NCT05480852 on 29/07/2022. All procedures involving human participants were performed in accordance with the ethical standards of the Research Ethics Committee of the Faculty of Dentistry, Minia University, Egypt, under the approval number 419 on 27/06/2020.

A Look Into the Cytotoxicity of Composite Fillings: Friend or Foe?

Dental resin composites are widely used restorative materials in dentistry for the treatment of carious and non-carious lesions as well as pit and fissure sealants, cavity liners, and endodontic sealers. They consist of two parts: an organic resin matrix and an inorganic/organic filler. The organic resin matrix phase is made up of multifunctional monomers and light-sensitive initiators, while the inorganic/organic filler phase is made up of micro/nano-sized fillers that primarily serve as reinforcement. Despite being a very promising dental material, its monomeric component has some drawbacks. It is well known for leaching out during incomplete polymerization, which can result in cytotoxicity. Bis-GMA (bisphenol A-glycidyl methacrylate) is the most cytotoxic of all monomeric components that exhibit synthetic estrogenic effects. The purpose of this article is to assess the cytotoxic effects of dental composite, understand the possible mechanism behind them, and explore ways to screen for and reduce this harmful effect, as well as shed light on its future prospects.

Physical-Chemical and Microhardness Properties of Model Dental Composites Containing 1,2-Bismethacrylate-3-eugenyl Propane Monomer.

A new eugenyl dimethacrylated monomer (symbolled BisMEP) has recently been synthesized. It showed promising viscosity and polymerizability as resin for dental composite. As a new monomer, BisMEP must be assessed further; thus, various physical, chemical, and mechanical properties have to be investigated. In this work, the aim was to investigate the potential use of BisMEP in place of the BisGMA matrix of resin-based composites (RBCs), totally or partially. Therefore, a list of model composites (CEa0, CEa25, CEa50, and CEa100) were prepared, which made up of 66 wt% synthesized silica fillers and 34 wt% organic matrices (BisGMA and TEGDMA; 1:1 wt/wt), while the novel BisMEP monomer has replaced the BisGMA content as 0.0, 25, 50, and 100 wt%, respectively. The RBCs were analyzed for their degree of conversion (DC)-based depth of cure at 1 and 2 mm thickness (DC1 and DC2), Vickers hardness (HV), water uptake (WSP), and water solubility (WSL) properties. Data were statistically analyzed using IBM SPSS v21, and the significance level was taken as p < 0.05. The results revealed no significant differences (p > 0.05) in the DC at 1 and 2 mm depth for the same composite. No significant differences in the DC between CEa0, CEa25, and CEa50; however, the difference becomes substantial (p < 0.05) with CEa100, suggesting possible incorporation of BisMEP at low dosage. Furthermore, DC1 for CEa0-CEa50 and DC2 for CEa0-CEa25 were found to be above the proposed minimum limit DC of 55%. Statistical analysis of the HV data showed no significant difference between CEa0, CEa25, and CEa50, while the difference became statistically significant after totally replacing BisGMA with BisMEP (CEa100). Notably, no significant differences in the WSP of various composites were detected. Likewise, WSL tests revealed no significant differences between such composites. These results suggest the possible usage of BisMEP in a mixture with BisGMA with no significant adverse effect on the DC, HV, WSP, and degradation (WSL).

Fabrication of Novel Pre-Polymerized BisGMA/Silica Nanocomposites: Physio-Mechanical Considerations.

Resin composite mimics tooth tissues both in structure and properties, and thus, they can withstand high biting force and the harsh environmental conditions of the mouth. Various inorganic nano- and micro-fillers are commonly used to enhance these composites' properties. In this study, we adopted a novel approach by using pre-polymerized bisphenol A-glycidyl methacrylate (BisGMA) ground particles (XL-BisGMA) as fillers in a BisGMA/triethylene glycol dimethacrylate (TEGDMA) resin system in combination with SiO2 nanoparticles. The BisGMA/TEGDMA/SiO2 mixture was filled with various concentrations of XL-BisGMA (0, 2.5, 5, and 10 wt.%). The XL-BisGMA added composites were evaluated for viscosity, degree of conversion (DC), microhardness, and thermal properties. The results demonstrated that the addition of a lower concentration of XL-BisGMA particles (2.5 wt.%) significantly reduced (p ≤ 0.05) the complex viscosity from 374.6 (Pa·s) to 170.84. (Pa·s). Similarly, DC was also increased significantly (p ≤ 0.05) by the addition of 2.5 wt.% XL-BisGMA, with the pristine composite showing a DC of (62.19 ± 3.2%) increased to (69.10 ± 3.4%). Moreover, the decomposition temperature has been increased from 410 °C for the pristine composite (BT-SB0) to 450 °C for the composite with 10 wt.% of XL-BisGMA (BT-SB10). The microhardness has also been significantly reduced (p ≤ 0.05) from 47.44 HV for the pristine composite (BT-SB0) to 29.91 HV for the composite with 2.5 wt.% of XL-BisGMA (BT-SB2.5). These results suggest that a XL-BisGMA could be used to a certain percentage as a promising filler in combination with inorganic fillers to enhance the DC and flow properties of the corresponding resin-based dental composites.

Tailoring the monomers to overcome the shortcomings of current dental resin composites - review.

Dental resin composites (DRCs) have become the first choice among different restorative materials for direct anterior and posterior restorations in the clinic. Though the properties of DRCs have been improved greatly in recent years, they still have several shortcomings, such as volumetric shrinkage and shrinkage stress, biofilm development, lack of radio-opacity for some specific DRCs, and estrogenicity, which need to be overcome. The resin matrix, composed of different monomers, constitutes the continuous phase and determine the performance of DRCs. Thus, the chemical structure of the monomers plays an important role in modifying the properties of DRCs. Numerous researchers have taken to design and develop novel monomers with specific functions for the purpose of fulfilling the needs in dentistry. In this review, the development of monomers in DRCs were highlighted, especially focusing on strategies aimed at reducing volumetric shrinkage and shrinkage stress, endowing bacteriocidal and antibacterial adhesion activities as well as protein-repelling activity, increasing radio-opacity, and replacing Bis-GMA. The influences of these novel monomers on the properties of DRCs were also discussed.

Rutin alleviates bisphenol A-glycidyl methacrylate-induced generation of proinflammatory mediators through the MAPK and NF-κB pathways in macrophages.

Bisphenol A-glycidyl methacrylate (BisGMA) is a methacrylate monomer that is mainly used in three-dimensional structures to reconstruct dental and bony defects. BisGMA has toxic and proinflammatory effects on macrophages. Rutin is a natural flavonol glycoside that is present in various plants and has useful biological effects, such as anti-inflammatory, anticancer, and antioxidative effects. The aim of this study was to investigate the anti-inflammation of rutin in macrophages after exposure to BisGMA. Pretreatment of the RAW264.7 macrophage with rutin at 0, 10, 30, and 100 µM for 30 min before being incubated with BisGMA at 0 or 3 µM. Proinflammatory cytokines and prostaglandin (PG) E2 were detected by enzyme-linked immunosorbent assay (ELISA). Nitric oxide (NO) was detected by the Griess assay. Expression and phosphorylation of proteins were measured by Western blot assay. Pretreatment with rutin inhibited the BisGMA-induced generation of proinflammatory cytokines, including tumor necrosis factor (TNF)-α, interleukin (IL)-1ß, IL-6, and PGE2, in macrophages. Rutin also suppressed the BisGMA-induced secretion of NO and expression of inducible nitric oxide synthase (iNOS) in a concentration-dependent manner. Furthermore, rutin suppressed the mitogen-activated protein kinase (MAPK) phosphorylation in a concentration-dependent manner. Finally, rutin suppressed the BisGMA-induced phosphorylation of nuclear factor (NF)-κB p65 and degradation of inhibitor of κB (IκB). These results indicate that the concentration of rutin has an inhibitory effect on proinflammatory mediator generation, MAPK phosphorylation, NF-κB p65 phosphorylation, and IκB degradation. In conclusion, rutin is a potential anti-inflammatory agent for BisGMA-stimulated macrophages through NF-κB p65 phosphorylation and IκB degradation resulting from MAPK phosphorylation.

Inducing cathepsin L expression/production, lysosomal activation, and autophagy of human dental pulp cells by dentin bonding agents, camphorquinone and BisGMA and the related mechanisms.

Camphorquinone (CQ) and resin monomers are included in dentin bonding agents (DBAs) and composite resin to restore tooth defects due to abrasion, crown fracture, or dental caries. DBAs, CQ, and bisphenol A-glycidyl methacrylate (BisGMA) applications influence the biological activities of the dental pulp. The current investigation aimed to delineate the effect of DBAs, CQ, and BisGMA on cathepsin L production/expression, lysosomal activity, and autophagy induction in human dental pulp cells (HDPCs). HDPCs were exposed to DBAs, CQ, or BisGMA with/without inhibitors for 24 h. Enzyme-linked immunosorbent assay was employed to determine the cathepsin L level in culture medium. The cell layer was utilized to measure cell viability by 3-(4,5-dimethyl-thiazol-2-yl)-2,5-diphenyl -tetrazolium bromide (MTT) assay. Real-time PCR was used to evaluate the mRNA expression. Western blotting or immunofluorescent staining was used to study protein expression. Lysosomal density was evaluated by lysotracker red staining. We found that DBAs, CQ, and BisGMA stimulated cathepsin L mRNA, protein expression, and production in HDPCs. In addition, CQ and BisGMA induced lysosomal activity, Beclin1, ATG12, LC3B, Bax, and p53 expression in HDPCs, indicating the stimulation of autophagy. Glutathione (GSH) prevented CQ- and BisGMA-induced cytotoxicity. Moreover, E64d, cathepsin L inhibitor (two cathepsin inhibitors), and Pifithrin-α (a p53 inhibitor) showed little preventive effect toward CQ- and BisGMA-induced cytotoxicity. Autophagy inhibitors (NH4Cl, Lys05) mildly enhanced the CQ- and BisGMA-induced cytotoxicity. These results indicate that DBAs stimulated cathepsin L, possibly due to their content of CQ and BisGMA that may induce cathepsin L in HDPCs. CQ and BisGMA stimulated lysosomal activity, autophagy, and apoptosis, possibly via induction of Beclin 1, ATG12, LC-3B, Bax, and p53 expression. In addition, CQ and BisGMA cytotoxicity was related to redox change and autophagy. These events are important role in pulpal changes after the restoration of tooth decay using CQ- and BisGMA-containing DBAs and resin composite.

Overviews on the Progress of Flowable Dental Polymeric Composites: Their Composition, Polymerization Process, Flowability and Radiopacity Aspects.

A review article has been conducted including the main research results and comments referring to flowable dental polymeric materials. To begin with, the synthesis and composition of this category of composites is discussed, revealing the major components of the commercial products in terms of chemistry and proportion. Later, the polymerization characteristics are unfolded regarding the reaction time and rate, volumetric shrinkage and depth of cure for both photocurable and self-curable composites. To continue, some perspectives of the pre-treatment or accompanying processes that a clinician may follow to enhance the materials' performance are described. Fluidity is certainly associated with the progress of polymerization and the in-depth conversion of monomers to a polymeric network. Last, the aspects of radiopacity and translucency are commented on, showing that all flowable polymeric composites satisfy the radiography rule, while the masking ability depends on the fillers' properties and specimen thickness. The reviewing article is addressed to all field scientists and practitioners dealing with flowable dental composites studies or applications.

Protective effect of wogonin on inflammatory responses in BisGMA-treated macrophages through the inhibition of MAPK and NFκB pathways.

Composites, resins, and sealants that are commonly used in orthopedics and dentistry are based on 2,2-bis[p-(2'-hydroxy-3'-methacryloxypropoxy)phenylene]propane (BisGMA), which induces proinflammatory responses in macrophages. The present study aimed to explore the anti-inflammatory responses of wogonin, which is a natural dihydroxyl flavonoid compound, in BisGMA-treated macrophages. According to the findings, wogonin exhibits anti-inflammatory, antiallergic, anticancer, and antioxidative properties. The generation of nitric oxide (NO) and the expression of inducible nitric oxide synthase (iNOS) were noted to be inhibited by wogonin in BisGMA-treated macrophages. Furthermore, the production of proinflammatory cytokines including tumor necrosis factor (TNF)-α, interleukin (IL)-1ß, and IL-6 was reduced. In addition, BisGMA-induced nuclear factor (NF)-κB p65 phosphorylation and inhibitor of κB (IκB) degradation were inhibited. Finally, the BisGMA-induced phosphorylation of mitogen-activated protein kinases (MAPKs), including p38 MAPK, extracellular signal-regulated kinase (ERK), c-Jun N-terminal kinase (JNK) was inhibited. All these effects were induced by wogonin in the macrophages in a concentration-dependent manner. Similar inhibitory effects of wogonin were observed on the production of NO and proinflammatory cytokines, expression of iNOS, phosphorylation of NF-κB p65 and MAPK, and degradation of IκB. These results indicated that rutin is a potential anti-inflammatory agent for BisGMA-treated macrophages that undergo NFκB p65 phosphorylation and IκB degradation through upstream MAPK phosphorylation. Therefore, wogonin inhibits BisGMA-induced proinflammatory responses in macrophages through the regulation of the NFκB pathway and its upstream factor, MAPK.

Evaluation of residual monomer release after polymerization of different restorative materials used in pediatric dentistry.

BACKGROUND: The choice of the restorative resin material to be used in pediatric dentistry is of a great importance due to the cytotoxic effects caused by residual monomers. In this study, it was aimed to investigate the amount of residual monomer released over time from different resin-based restorative materials, which are widely used in pediatric dentistry, by using high performance liquid chromatography with photodiode array detector (HPLC-PDA). METHODS: The compomers in all colors (Twinky Star and Glasiositte A2), two composites with different hybrid properties (Arabesk-GrandioSO), and RMGIC (Ionolux) samples with 2 × 5 mm diameters were prepared. The samples were polymerized with an LED light unit (CELALUX 2, VOCO, Cuxhaven, Germany) and then finishing-polishing procedures were applied. A total of 156 samples were obtained, 13 samples in each of the 12 groups. The amount of residual monomer (BIS-GMA; HEMA, TEGDMA, UDMA) (µg/mL) released into the 75% ethanol solution was determined at different times, (1st hour, 1st, 7th, 14th, and 21st day) by using HPLC-PDA. RESULTS: The residual monomer release continued on day 21 and BIS-GMA was the most released monomer in all groups. HEMA release showed a maximum increase in all the materials at day 7. The highest amount of residual monomer was detected in the gold-colored compomer. HEMA and BIS-GMA release from RMGIC was less than others in all time frames. CONCLUSIONS: The color and composition of resin-based restorative materials affect the amount of residual monomer. Pediatric dentists should prefer gold-colored compomers less than others as a restorative material, especially in deep cavities. More studies are needed about the subject.

Biocompatibility and mechanical properties of an experimental E-glass fiber-reinforced composite for dentistry.

Objectives: To evaluate the biocompatibility and mechanical properties of experimental bis-phenol-A and bis-GMA free E-glass fiber-reinforced composites (FRCs) prepared with hexanediol dimethacrylate (HDDMA) based resin. Methods: Two ratios of HDDMA/TEGDMA resin were evaluated: exp-1 (70/30 wt.%) and exp-2 (50/50 wt.%) with two bis-GMA resin control groups (bis-GMA/MMA and bis-GMA/TEGDMA resins, both 70/30 wt.%). E-glass fibers were embedded into the resins to prepare FRCs specimens. Biocompatibility was assessed for cytoviability and biofilm formation with Streptococcus mutans, Streptococcus sanguinis, Enterococcus faecalis, and Candida albicans. Mechanical properties were evaluated for flexural strength and hardness (24 h, water storage 1 and 28 days), water sorption (1, 7, 14, and 28 days), contact angle, and surface roughness. The data were analyzed statistically by one-way and two-way ANOVA (p < 0.05). Results: Cytoviability of the experimental groups was significantly higher than the control groups (p < 0.05). The exp-1 cytoviability (98.2 ± 1.3%) met the ISO 10993-5 standard requirement for noncytotoxic materials. The adherence of bacteria to the experimental FRCs was visibly less than the controls, while Candida albicans adhered visibly more to the experimental groups than the controls (p < 0.05). Flexural strength showed slightly higher values for controls than for the experimental groups. The exp-1 hardness value was significantly higher in the control groups for all storage conditions (p < 0.05). The water sorption of the experimental groups was significantly higher than the controls. The surface roughness indicated no significant difference (p = 0.87). The exp-1 showed a higher contact angle with the control groups. Conclusion: The experimental HDDMA/TEGDMA-based FRCs might be potential alternatives for bis-GMA-based FRCs. Clinical significance: The HDDMA/TEGDMA E-glass FRCs might provide biocompatible restorations.

Investigation of antimicrobial and mechanical effects of functional nanoparticles in novel dental resin composites.

OBJECTIVES: Imidazole and benzimidazole derivatives have recently attracted attention as remarkable materials due to their advantages in chemistry, pharmacology, and biomaterials. This article focuses on dental composites with azole functional groups incorporated to affect their physicochemical and mechanical properties and antibacterial activity. METHODS: Dental composites were fabricated by embedding the functionalized imidazole and benzimidazole nanoparticles into a Bis-GMA/TEGDMA matrix to form the imidazole and benzimidazole dental composites series (I and B). The material was produced through hand blending of the monomer (50:50, wt%), filler (0-30, wt%), and initiator combination (CQ/EDMAB:0.8:1.6, wt%), and LED light-curing unit for 60 s. RESULTS: Using various characterization techniques, I and B series were validated. The dental composites' approximate solubility and sorption significances were evaluated by conducting experiments on specific dental composite formulations. Fenton reaction test was performed to determine the chemical stability of the dental composites. The mechanical properties of the dental composites were investigated. Finally, by testing cell growth in the presence of composites, their antibacterial activities were determined. CONCLUSIONS: In this study, it was observed that the mechanical, physiochemical, and antibacterial properties of the functional azole-containing nanoparticles were positively improved by adding them to the structure of dental composites. These experimental results paved the way for the synthesized materials to be used in industrial applications. CLINICAL SIGNIFICANCE: Since the chemical, mechanical, and antimicrobial properties of dental composites containing 10% imidazole and benzimidazole functional nanoparticles are far superior, they constitute an excellent alternative for preventing dental caries and long-term use of dental composites.

Preparation of Bis-GMA free dental resin composites with anti-adhesion effect against Streptococcus mutans using synthesized fluorine-containing methacrylate (DFMA).

With purpose of preparing Bis-GMA free dental resin composites (DRCs) with anti-adhesion effect against Streptococcus mutans (S. mutans), a new fluorinated dimethacrylate (DFMA) was synthesized and used as base resin of DRCs. Two reactive diluents TEGDMA and SR833s were mixed with DFMA separately to prepare resin matrixes. After mixing with inorganic fillers, two DFMA based DRCs were obtained and named as DT (DFMA/TEGDMA) and DS (DFMA/SR833s) according to the resin matrix composition. Bis-GMA based DRC (BT) was used as control. The double bond conversion (DC), bacteria adhesion, mucin adsorption, contact angle, surface free energy, volumetric shrinkage (VS), shrinkage stress (SS), water sorption (WS) and solubility (SL), flexural strength (FS) and modulus (FM) before and after water immersion were investigated, and all the results were statistically analyzed with ANOVA analysis. The results showed that DT and DS had comparable (ρ > 0.05) surface free energy which was lower than that of BT (ρ < 0.05). Compared with BT, with the same surface roughness (ρ > 0.05), less amount of S. mutans was accumulated on the surface of DT and DS (ρ < 0.05). In all DRCs, the DS had the best resistance to mucin adsorption (ρ < 0.05) due to its high hydrophobicity. Compared with BT, both DFMA based DRCs had advantages such as lower VS and SS (ρ < 0.05), lower WS and SL (ρ < 0.05), and better water resistance. The DS, which had antibacterial adhesion effect, mucin adsorption resistance, lowest VS and SL (ρ < 0.05), and the highest FS and FM no matter before or after water immersion (ρ < 0.05) was considered to have the best comprehensive properties in all DRCs.

The Influence of Low-Molecular-Weight Monomers (TEGDMA, HDDMA, HEMA) on the Properties of Selected Matrices and Composites Based on Bis-GMA and UDMA.

Bisphenol A-glycidyl methacrylate (bis-GMA) and urethane dimethacrylate (UDMA) are usually combined with low-viscosity monomers to obtain more desirable viscosity, handling characteristics and general properties. The present study determined the flexural strength (FS), flexural modulus (FM), diametral tensile strength (DTS), and hardness (HV) of five matrices and composites based on these resins. The polymerization shrinkage stress (PSS) was also studied for the composites. The polymer matrices were formed using bis-GMA and UDMA. TEGDMA, HEMA and HDDMA acted as co-monomers. The composites had 45 wt.% of filler content. The highest FS and FM were obtained from the UDMA/bis-GMA/TEGDMA/HEMA matrix and the composite (matrix + filler). The best DTS values were obtained from the UDMA/bis-GMA/HEMA matrix and the composite. One of the lowest values of FS, FM, and DTS was obtained from the UDMA/bis-GMA/HDDMA matrix and the composite. All the composites demonstrated similar hardness values. The lowest polymerization shrinkage stress was observed for the UDMA/bis-GMA/TEGDMA/HEMA composite, and the highest PSS was observed for the UDMA/bis-GMA/TEGDMA/HDDMA composite. The addition of HEMA had a positive effect on the properties of the tested materials, which may be related to the improved mobility of the bis-GMA and UDMA monomers.

Influence of Dimethacrylate Monomer on the Polymerization Efficacy of Resin-Based Dental Cements-FTIR Analysis.

The degree of polymerization for dimethacrylate resin-based materials (BisGMA, TEGDMA, UDMA, HEMA) ranges from 55 to 75%. Literature data indicate that polymerization efficacy depends, among other factors, on the type of methacrylate resin comprising the material. The aim of this study was to evaluate the polymerization efficacy of four dental cement materials characterized by different polymerization mechanisms using FTIR analysis. In the present study, the FTIR method was adopted to analyze the degree of polymerization efficacy of four resin-based dental cement materials, two of which were self-cured and two were dual-cured cements. The IR spectral analysis was performed 24 h after the polymerization of the cementitious material. RelyX ARC cement exhibits the lowest polymerization efficacy (61.3%), while that of Variolink II (85.8%) and Maxcem Elite is the highest (90.1%). Although the efficacy of self-cured cements appears to be superior, the difference is not statistically significant (p = 0.280). Polymerization efficacy largely depends on the chemical structure of the material in terms of the presence of a particular methacrylate resin and less on the polymerization mechanism itself, i.e., whether it is a self-cured or dually cured dental cement. Thus, in clinical practice, cementitious materials with a higher proportion of TEGDMA compared with BisGMA are recommended.

Monomer Elution from Three Resin Composites at Two Different Time Interval Using High Performance Liquid Chromatography-An In-Vitro Study.

Esthetics, improved colour stability and ease of contour have made photo-activated resin based restorative materials being widely used in routine dental clinical practice. Perhaps improper and inadequate polymerization of resin based composite material might lead to elution of monomer. Thus, the aim of the current study was to quantify the monomer elution from three resin composites. The intended analysis was made using high performance liquid chromatography (HPLC) at two different time periods. Three different materials that were investigated in the current study included Swiss Tech resin composite (Group A), Ceram X (Group B) and Beautifil Injectable composite (Group C). Ten cylindrical samples were fabricated in each study group. In 75% wt of ethanol, the samples were ingressed immediately and stored at room temperature. A 0.5 mL of the samples was assessed at pre-defined time intervals at 24 h and 7th day. Later, assessment of the samples was performed with HPLC and the data was analyzed using statistical test. Bisphenol A-glycidyl methacrylate (Bis-GMA), Triethylene glycol dimethacrylate (TEGDMA), 2-hydroxyethyl methacrylate (HEMA) and Urethane dimethacrylate (UDMA) were quantified in the samples. When analyzing the release monomer, it was found that at the end of 24 h Bis-GMA was eluted more in the injectable resin composite whereas, TEGDMA was eluted from Swiss Tech and Ceram X resin composites. At the end of the 7th day it was evident that Bis-GMA was eluted maximum in all the three resin composites. Thus, monomer release was found to be evident among all three resin composites and it is of utmost important to be assessed in routine clinical practice.