A highly sensitive electrochemical sensor based on poly(3-aminobenzoic acid)/graphene oxide-gold nanoparticles modified screen printed carbon electrode for paraquat detection.

Herein, a modified screen printed carbon electrode (SPCE) based on a composite material, graphene oxide-gold nanoparticles (GO-AuNPs), and poly(3-aminobenzoic acid)(P3ABA) for the detection of paraquat (PQ) is introduced. The modified electrode was fabricated by drop casting of the GO-AuNPs, followed by electropolymerization of 3-aminobenzoic acid to achieve SPCE/GO-AuNPs/P3ABA. The morphology and microstructural characteristics of the modified electrodes were revealed by scanning electron microscopy (SEM) for each step of modification. The composite GO-AuNPs can provide high surface area and enhance electroconductivity of the electrode. In addition, the presence of negatively charged P3ABA notably improved PQ adsorption and electron transfer rate, which stimulate redox reaction on the modified electrode, thus improving the sensitivity of PQ analysis. The SPCE/GO-AuNPs/P3ABA offered a wide linear range of PQ determination (10-9-10-4 mol/L) and low limit of detection (LOD) of 0.45 × 10-9 mol/L or 0.116 µg/L, which is far below international safety regulations. The modified electrode showed minimum interference effect with percent recovery ranging from 96.5% to 116.1% after addition of other herbicides, pesticides, metal ions, and additives. The stability of the SPCE/GO-AuNPs/P3ABA was evaluated, and the results indicated negligible changes in the detection signal over 9 weeks. Moreover, this modified electrode was successfully implemented for PQ analysis in both natural and tapped water with high accuracy.

Sensitive electrochemical determination of quercetin and folic acid with cobalt nanoparticle functionalized multi-walled carbon nanotube.

A nanocomposite of cobalt nanoparticle (CoNP) functionalized carbon nanotube (Co@CNT) was prepared and used to modify a glassy carbon electrode (Co@CNT/GCE). Characterization indicates the morphology of Co@CNT is CoNPs adhering on CNTs. With the nano-interface, Co@CNT provides large surface area, high catalytic activity, and efficient electron transfer, which makes Co@CNT/GCE exhibiting satisfactory electrochemical response toward quercetin (QC) and folic acid (FA). The optimum pH values for the detection of FA and QC are 7.0 and 3.0, respectively. The saturated absorption capacity (Γ*) and catalytic rate constant (kcat) of Co@CNT/GCE for QC and FA are calculated as 1.76 × 10-9, 3.94 × 10-10 mol∙cm-2 and 3.04 × 102, 0.569 × 102 M-1∙s-1. The linear range for both FA and QC is estimated to be 5.0 nM-10 µM, and the LODs (3σ/s) were 2.30 nM and 2.50 nM, respectively. The contents of FA and QC in real samples determined by Co@CNT/GCE are comparable with the results determined by HPLC. The recoveries were in the range 90.5 ~ 114% and the total RSD was lower than 8.67%, which further confirms the reliability of the proposed electrode for practical use.

Ensuring food safety by artificial intelligence-enhanced nanosensor arrays.

Current analytical methods utilized for food safety inspection requires improvement in terms of their cost-efficiency, speed of detection, and ease of use. Sensor array technology has emerged as a food safety assessment method that applies multiple cross-reactive sensors to identify specific targets via pattern recognition. When the sensor arrays are fabricated with nanomaterials, the binding affinity of analytes to the sensors and the response of sensor arrays can be remarkably enhanced, thereby making the detection process more rapid, sensitive, and accurate. Data analysis is vital in converting the signals from sensor arrays into meaningful information regarding the analytes. As the sensor arrays can generate complex, high-dimensional data in response to analytes, they require the use of machine learning algorithms to reduce the dimensionality of the data to gain more reliable outcomes. Moreover, the advances in handheld smart devices have made it easier to read and analyze the sensor array signals, with the advantages of convenience, portability, and efficiency. While facing some challenges, the integration of artificial intelligence with nanosensor arrays holds promise for enhancing food safety monitoring.

THP as a sensor for the electrochemical detection of H2O2.

Hydrogen peroxide (H2O2) detection is paramount in biological and clinical domains due to its pivotal role in various physiological and pathological processes. This molecule is a crucial metabolite and effector in cellular redox mechanisms, influencing diverse cellular signaling pathways and bolstering the body's defense mechanisms against infection and oxidative stress. Organic molecule-based electrodes present unique advantages such as operational versatility and scalability, rendering them attractive candidates for sensor development across diverse fields encompassing food safety, healthcare, and environmental monitoring. This study explores the electrochemical properties of a tris(3-hydroxypyridin-4-one) THP, which has been unexplored in electrochemical sensing. Leveraging THP's chelating properties, we aimed to develop an electrochemical probe for hydrogen peroxide detection. Our investigations reveal promising results, with the developed sensor exhibiting a low limit of detection (LOD) of 144 nM, underscoring its potential utility in sensitive and selective H2O2 detection applications. In addition, the new sensor was also tested on fetal bovine serum (FBS) to emphasize future applications on biological matrices. This research signifies a significant stride in advancing electrochemical sensor technologies for hydrogen peroxide detection with several novelties related to the usage of THP, such as high sensitivity and selectivity, performance in biological matrices, repeatability, stability, and reproducibility, economical and practical advantages. This research opens new avenues for enhanced biomedical diagnostics and therapeutic interventions.

Hollow-like three-dimensional structure of methyl orange-delaminated Ti3C2 MXene nanocomposite for high-performance electrochemical sensing of tryptophan.

Tryptophan(Trp) is being explored as a potential biomarker for various diseases associated with decreased tryptophan levels; however, metabolomic methods are expensive and time-consuming and require extensive sample analysis, making them urgently needed for trace detection. To exploit the properties of Ti3C2 MXenes a rational porous methyl orange (MO)-delaminated Ti3C2 MXene was prepared via a facile mixing process for the electrocatalytic oxidation of Trp. The hollow-like 3D structure with a more open structure and the synergistic effect of MO and conductive Ti3C2 MXene enhanced its electrochemical catalytic capability toward Trp biosensing. More importantly, MO can stabilize Ti3C2 MXene nanosheets through noncovalent π-π interactions and hydrogen bonding. Compared with covalent attachment, these non-covalent interactions preserve the electronic conductivity of the Ti3C2 MXene nanosheets. Finally, the addition of MO-derived nitrogen (N) and sulfur (S) atoms to Ti3C2 MXene enhanced the electronegativity and improved its affinity for specific molecules, resulting in high-performance electrocatalytic activity. The proposed biosensor exhibited a wide linear response in concentration ranges of 0.01-0.3 µM and 0.5-120 µM, with a low detection limit of 15 nM for tryptophan detection, and high anti-interference ability in complex media of human urine and egg white matrices. The exceptional abilities of the MO/Ti3C2 nanocatalyst make it a promising electrode material for the detection of important biomolecules.

2D sheet structure of zinc molybdate decorated on MXene for highly selective and sensitive electrochemical detection of the arsenic drug Roxarsone in water samples.

Water contamination is a serious environmental issue posing a significant global challenge. Roxarsone (ROX), a widely used anticoccidial drug, is excreted in urine and feces, potentially disrupting natural habitats. Therefore, rapid and cost-effective ROX detection is essential. In this study, we developed a 2D sheet structure of zinc molybdate decorated on MXene (ZnMoO4/MXene) for detecting ROX using electrochemical methods. The materials were characterized using appropriate spectrophotometric and voltammetric techniques. The ZnMoO4/MXene hybrid exhibited excellent electrocatalytic performance due to its rapid electron transfer rate and higher electrical conductivity. The ZnMoO4/MXene- modified GCE (ZnMoO4/MXene/GCE) showed a broad linear range with high sensitivity (10.413 µA µÐœ-1 cm-2) and appreciable limit of detection (LOD) as low as 0.0081 µM. It also demonstrated significant anti-interference capabilities, excellent storage stability, and remarkable reproducibility. Furthermore, the feasibility of utilizing ZnMoO4/MXene/GCE for monitoring ROX in water samples was confirmed, achieving satisfactory recoveries.

Electrochemical real-time sensor for the detection of Pb(II) ions based on Ti3C2Tx MXene.

Lead ions are especially harmful to human health, causing significant developmental and behavioral abnormalities even at small concentrations. In real-life samples, lead ions are present in mixtures with other metal ions, creating a challenge to detect it selectively at low quantities. To address these challenges, we prepared an electrochemical sensor based on delaminated Ti3C2Tx MXene, which can selectively detect low concentrations of Pb2+ in a solution containing other common metal ions. Cyclic voltammetry was applied as an electrochemical detection method. The proposed reaction mechanism involves a reversible transition between Pb2+ ions and PbO at the MXene-based layer. The sensitivity of the sensor towards Pb2+ ions and a limit of detection were determined. The sensor, as prepared, had a linear response range within 0.15-1.0 µM, with a sensitivity of 26.7 µA/µM and LOD value of 48.7 nM, which meets the requirements set by the World Health Organization.

A high-performance electrochemical sensor based on dendritic Au/Zn modified carbon cloth for the determination of nitrite in aquaculture.

Nitrite is a common nitrogen-containing compound that possesses high biological toxicity, thereby posing a serious threat to aquatic organisms. Therefore, it is imperative to develop a rapid and quantitative determination approach for nitrite. In this study, the aim was to prepare a novel electrochemical sensor to determine nitrite. This was achieved by synthesizing Au/Zn dendritic complexes on a carbon cloth self-supported electrode after plasma treated by a stepwise strategy of electrodeposition and in-situ corrosion. In accordance with the optimal experimental conditions, the electrode exhibited remarkable catalytic activity for the electrooxidation of nitrite ions (pH = 8.0), accompanied by a considerable enhancement in peak anodic current in comparison to the unmodified electrode. The sensor exhibited a wide linear range (1-833 µM, 833-8330 µM), high sensitivity (3506 µA mM-1 cm-2, 538 µA mM-1 cm-2), a low detection limit (0.43 µM), and excellent selectivity, reproducibility, and stability for the determination of nitrite. Furthermore, the prepared sensor was successfully applied to the detection of nitrite in tap water, fish holding pond water and duck pond water, demonstrating good recovery and no significant difference from the spectrophotometric results. The results suggest that the electrochemical sensor developed in this study represents a straightforward yet efficacious approach to the development of advanced portable sensors for aquaculture applications.

Microplasma-assisted construction of cross-linked network hierarchical structure of NiMoO4 nanorods @NiCo-LDH nanosheets for electrochemical sensing of non-enzymatic H2O2 in food.

The accumulation of small doses of hydrogen peroxide (H2O2) into food can cause many diseases in the human body, and it is urgent to develop efficient detection methods of H2O2. Herein, the hierarchical structure composite of NiCo-LDH nanosheets crosslinked NiMoO4 nanorods was grown in situ on carbon cloth (NiMoO4 NRs@NiCo-LDH NSs/CC) by micro-plasma assisted hydrothermal method. Thanks to the synergistic effect of three metals and (NiMoO4 NRs@NiCo-LDH NSs/CC) provided by nanorods/nanosheets hierarchical structure, NiMoO4 NRs@NiCo-LDH NSs/CC exposes more active sites and achieves rapid electron transfer. The H2O2 electrochemical sensor was constructed as the working electrode with a linear range of 1 µmol L-1 to 9.0 mmol L-1 and detection limit of 112 nmol L-1. In addition, the sensor has been successfully applied to the detection of H2O2 in food samples, the recovery rate is 95.2%-106.62%, RSD < 4.89%.

Self-powered sensing platform for monitoring uric acid in sweat using cobalt nanocrystal-graphene quantum dot-Ti3C2TX monolithic film electrode with excellent supercapacitor and sensing behavior.

The synthesis of cobalt nanocrystal-graphene quantum dot-Ti3C2TX monolithic film electrode (Co-GQD-Ti3C2TX) is reported via self-assembly of Ti3C2TX nanosheets induced by protonated arginine-functionalized graphene quantum dot and subsequent reduction of cobalt (III). The resulting Co-GQD-Ti3C2TX shows good monolithic architecture, mechanical property, dispersibility and conductivity. The structure achieves excellent supercapacitor and sensing behavior. The self-charging supercapacitor produced by printing viscous Co-GQD-Ti3C2TX hydrogel on the back of flexible solar cell surface provides high specific capacitance (296 F g-1 at 1 A g-1), high-rate capacity (153 F g-1 at 20 A g-1), capacity retention (98.1% over 10,000-cycle) and energy density (29.6 W h kg-1 at 299.9 W kg-1). The electrochemical chip produced by printing Co-GQD-Ti3C2TX hydrogel on paper exhibits sensitive electrochemical response towards uric acid. The increase of uric acid between 0.01 and 800 µM causes a linear increase in differential pulse voltammetry signal with a detection limit of 0.0032 µM. The self-powered sensing platform integrating self-charging supercapacitor, electrochemical chip and micro electrochemical workstation was contentedly applied to monitoring uric acid in sweats and shows one broad application prospect in wearable electronic health monitoring device.

In situ deposition of bismuth on pre-anodized screen-printed electrode for sensitive determination of Cd2+ in water and rice with a portable device.

Electrochemical detection is favorable for the rapid and sensitive determination of heavy metal cadmium. However, the detection sensitivity needs to be further improved, and a portable, low-cost device is needed for on-site detection. Herein, an in-situ bismuth modified pre-anodized screen-printed carbon electrode (SPCE) was developed for Cd2+ determination by square wave anodic stripping voltammetry (SWASV). The in-situ bismuth modification enhances the enrichment of Cd2+, and together with pre-anodization improve the electron transfer rate of electrode, thus enhancing the detection sensitivity. The electrode modification method combines pre-anodization and in-situ bismuth deposition, which is very easy and effective. Furthermore, a self-made PSoC Stat potentiostat coupled with a stirring device was fabricated for portable and low-cost electrochemical detection. After comprehensive optimization, the developed method can reach a testing time of 3 min, a detection limit of 3.55 µg/L, a linear range of 5-100 µg/L, and a recovery rate of 91.7-107.1% in water and rice samples for Cd2+ determination. Therefore, our method holds great promise for the rapid, sensitive and on-site determination of Cd2+ in food samples.

3D/2D-Bismuth Oxybromide Spheres with Selenium-Doped Graphitic Carbon Nitride Sheets: An Efficient Electrocatalyst for the Detection of Arsenic Drug Roxarsone.

Heavy metals are crucial carcinogenic agents threatening the environment and living habituates. Among them, arsenic (As) is an important metalloid that is categorized as a group I toxic carcinogen. Roxarsone (RX) is an organoarsenic antibiotic compound primarily used as a veterinarian drug and growth promoter for poultry animals. The extensive usage of RX increased the accumulation of As in living beings and the ecosystem. Therefore, we have prepared an electrochemical sensor based on 3D bismuth oxybromide with 2D selenium-doped graphitic carbon nitride (BOB/SCN) electrocatalyst for the rapid detection of RX. The elemental and structural details were thoroughly investigated with several spectroscopic techniques. The electrochemical properties were measured by impedance and voltammetric measurements. The electrocatalytic behavior toward the RX was estimated with different voltammetric methods. Therefore, our BOB/SCN-based electrochemical sensor demonstrated a low detection limit (2.3 nM), low quantification value (7.7 nM), optimal sensitivity (0.675 µA µM-1 cm-2), and good linear ranges (0.01-77 and 77-857 µM). Additionally, this sensor showed good electrochemical performance and was applied to monitor the RX in various real samples with remarkable recoveries. Based on these results, our BOB/SCN sensor is a promising electrochemical platform for determining RX.

Tailored portable electrochemical sensor for dopamine detection in human fluids using heteroatom-doped three-dimensional g-C3N4 hornet nest structure.

BACKGROUND: There is widespread interest in the design of portable electrochemical sensors for the selective monitoring of biomolecules. Dopamine (DA) is one of the neurotransmitter molecules that play a key role in the monitoring of some neuronal disorders such as Alzheimer's and Parkinson's diseases. Facile synthesis of the highly active surface interface to design a portable electrochemical sensor for the sensitive and selective monitoring of biomolecules (i.e., DA) in its resources such as human fluids is highly required. RESULTS: The designed sensor is based on a three-dimensional phosphorous and sulfur resembling a g-C3N4 hornet's nest (3D-PS-doped CNHN). The morphological structure of 3D-PS-doped CNHN features multi-open gates and numerous vacant voids, presenting a novel design reminiscent of a hornet's nest. The outer surface exhibits a heterogeneous structure with a wave orientation and rough surface texture. Each gate structure takes on a hexagonal shape with a wall size of approximately 100 nm. These structural characteristics, including high surface area and hierarchical design, facilitate the diffusion of electrolytes and enhance the binding and high loading of DA molecules on both inner and outer surfaces. The multifunctional nature of g-C3N4, incorporating phosphorous and sulfur atoms, contributes to a versatile surface that improves DA binding. Additionally, the phosphate and sulfate groups' functionalities enhance sensing properties, thereby outlining selectivity. The resulting portable 3D-PS-doped CNHN sensor demonstrates high sensitivity with a low limit of detection (7.8 nM) and a broad linear range spanning from 10 to 500 nM. SIGNIFICANCE: The portable DA sensor based on the 3D-PS-doped CNHN/SPCE exhibits excellent recovery of DA molecules in human fluids, such as human serum and urine samples, demonstrating high stability and good reproducibility. The designed portable DA sensor could find utility in the detection of DA in clinical samples, showcasing its potential for practical applications in medical settings.

Monodispersed Au nanoparticles decorated MoS2 nanosheets with enhanced peroxidase-like activity based electrochemical H2O2 sensing for anticancer drug evaluations.

BACKGROUND: The unique size, physical and chemical properties, and ultra-high stability of nanozymes have attracted extensive attentions in sensing, but improvement of catalytic activity of the nanozymes is still an urgent issue. Given the ultra-high simulated enzyme activity of metal nanoparticles and the advantage of multi-enzyme catalysis, an Au-decorated MoS2 nanosheets (MoS2/Au NS) integrating the double peroxidase-like (POD) activity is developed. RESULTS: By optimizing and adjusting the density of AuNPs, as well as its morphology and other parameters, a monodisperse and high-density distribution of AuNPs on MoS2 nanosheets was obtained, which can greatly improve the POD-like activity of MoS2/Au NS. Nafion solution was applied to assist the modification of MoS2/Au NS on the electrode surface so as to improved its stability. An electrochemical H2O2 detection platform was constructed by modifying MoS2/Au NS nanozyme on the SPCE using the conductive Nafion solution. And the negatively charged sulfonic acid group can eliminate negatively charged electroactive substances to improve the specificity. Then ascorbic acid was used to stimulate tumor cells to produce H2O2 as therapeutic model, an ultrasensitive chronocoulometry detection for H2O2 in cell lysate was established. The logarithmically of ΔQ and the logarithmically of H2O2 concentration showed a good linear relationship between 1 µM and 500 mM, with a LOD value of 0.3 µM. SIGNIFICANCE: The developed H2O2 sensor has excellent stability, reproducibility (RSD = 2.3 %, n = 6) and selectivity, realized the quantitative detection of H2O2 in cell lysate. Compared with commercial fluorescence detection kits for H2O2 in cell lysate, it is worth mentioning that the electrochemical H2O2 sensor developed in this study is simpler and faster, with higher sensitivity and lower cost. This provides a potential substitute for disease diagnosis and treatment evaluation based on accurate detection of H2O2.

Nanoarchitecturing of Mo2C nanospheres on carbon cloth as an electrochemical sensing platform for determination of caffeic acid in tea samples.

In the present paper, carbon cloth (CC) as a flexible substrate was modified by molybdenum carbide nanospheres (Mo2C NSs @CC) by the drop-coating method to develop a sensitive electrochemical platform for detecting caffeic acid. The uniform Mo2C NSs were prepared via an easy route followed by pyrolyzing the precursor of the Mo-polydopamine (Mo-PDA) NSs. The Mo2C NSs were characterized and analyzed by X-ray diffraction (XRD), field emission scanning electron microscopy/energy dispersive X-ray spectroscopy (FE-SEM/EDS), Raman spectroscopy (RS), and electrochemical methods. CC not only gave a flexible feature to the sensor but also provided a larger surface area for Mo2C NSs. Meanwhile, the excellent conductivity and large electroactive specific surface area of Mo2C NSs exhibited excellent electrocatalytic performance for caffeic acid determination. The developed sensor showed high sensitivity and selectivity, good reproducibility, and long-term stability with a limit of detection (LOD) and a wide linear range of 0.001 µM (S/N = 3) and 0.01-50 µM, respectively. In addition, the Mo2C NSs @CC sensor showed a promising application prospect for the detection of caffeic acid in green and black tea samples, indicating its importance in food safety and the food industry.

Pitfalls and challenges of peptide nucleic acid immobilisation on carbon surfaces for sequence-specific capturing of nucleic acid biomarkers.

Nucleic acid sensors based on a peptide nucleic acid (PNA) probe have seen a surge in interest since their discovery in the 1990s, and after the patent protecting them expired in 2013. The appeal of PNA as capture and/or sensing probes as an alternative to standard DNA or RNA oligonucleotides originates from their superior chemical stability and affinity for complementary oligonucleotides, as well as their increased responsiveness to single base mismatches. The implementation of PNA probes onto optical and electrochemical sensors has showed great promise although progress has been hampered by issues mostly associated with surface chemistry, probe accessibility and non-specific binding. Herein, we report on a systematic comparison between various PNA immobilisation strategies on carbon substrates based on both covalent and non-covalent chemistries. Besides the use of standard electrochemical techniques to characterise the extent of surface modification, the ability of immobilised PNAs to engage in chemical interactions with freely diffusing molecules was also investigated. Using original chemical tags, this study provides a unique insight into the impact of immobilisation chemistries on PNA's (bio)availability. Rapid immobilisation of biotinylated PNA oligomers on screen-printed carbon electrode (SPCE) coated with adsorbed polystreptavidin (pSA) demonstrated highest efficiency and ease in the preparation process. An original nucleic acid sensor using this immobilisation chemistry is reported that is based on a sandwich assay between a surface bound PNA capture probe and a freely diffusing electrochemically active PNA sensing probe.

IMSIS: An instrumented microphysiological system with integrated sensors for monitoring cellular metabolic activities.

Well plates are widely used in biological experiments, particularly in pharmaceutical sciences and cell biology. Its popularity stems from its versatility to support a variety of fluorescent markers for high throughput monitoring of cellular activities. However, using fluorescent markers in traditional well plates has its own challenges, namely, they can be potentially toxic to cells, and thus, may perturb their biological functions; and it is difficult to monitor multiple analytes concurrently and in real-time inside each well. This paper presents a fully instrumented microphysiological system with integrated sensors (IMSIS) with a similar well format. Each well in the microphysiological system has a set of sensors for monitoring multiple metabolic analytes in real-time. The IMSIS platform is supported by integrated bioelectronic circuits and a graphical user interface for easy user configuration and monitoring. The system has integrated microfluidics to maintain its microphysiological environment within each well. The IMSIS platform currently incorporates O2, H2O2, and pH sensors inside each well, allowing up to six wells to perform concurrent measurements in real-time. Furthermore, the architecture is scalable to achieve an even higher level of throughput. The miniaturized design ensures portability, suitable for small offices and field applications. The IMSIS platform was successfully used to monitor in real-time the mitochondrial functions of live bovine embryos in O2 consumption, H2O2 release as an indication of ROS production, and extracellular acidity changes before and after the introduction of external substrates.

Molecularly imprinted polymer-based electrochemical sensor for rapid detection of masked deoxynivalenol with Mn-doped CeO2 nanozyme as signal amplifier.

Deoxynivalenol-3-glucoside (D3G), the masked form of the important mycotoxin deoxynivalenol (DON), displays potential toxicity but is difficult to control owing to the lack of rapid detection methods. Herein, an innovative molecularly imprinted polymer (MIP)-based electrochemical sensor was developed for the rapid detection of D3G. MIP, an efficient recognition element for D3G, was electropolymerized using o-phenylenediamine based on a surface functional monomer-directing strategy for the first time. CeO2, which contains both Ce3+ and Ce4+ oxidation states, was introduced as a nanozyme to catalyze H2O2 reduction, while Mn doping generated more oxygen vacancies and considerably improved the catalytic activity. Mn-CeO2 also served as a promising substrate material because of its large surface area and excellent conductivity. Under optimal conditions, a good linear relationship was observed for D3G detection over the concentration range of 0.01-50 ng/mL. The proposed sensor could detect D3G down to 0.003 ng/mL with excellent selectivity, even distinguishing its precursor DON in complex samples. The sensor exhibited acceptable stability with high reproducibility and accuracy, and could successfully determine D3G in grain samples. To the best of our knowledge, this is the first electrochemical sensing platform for rapid D3G detection that can easily be expanded to other masked mycotoxins.

Bimetallic MOF-based electrochemical sensor for determination of paracetamol in spiked human plasma.

Metal-organic frameworks (MOFs) with their exceptional properties have the potential to revolutionize the field of electrochemistry and pave the way for new and exciting applications. MOFs is an excellent choice as an active electrocatalyst component in the fabrication of electrochemical sensors. Here, bimetallic NiCo-MOFs, monometallic Ni-MOFs, and Co-MOFs were fabricated to modify the carbon paste electrode. Moreover, the ratio between Co and Ni within the bimetallic MOFs was optimized. Our aim in this work is to synthesize different compositions from bimetallic MOFs and systematically compare their catalytic activity with mono-metallic MOFs on paracetamol. The structure and properties of the 2D NiCo-MOFs were characterized by scanning electron microscope, X-ray photoelectron spectroscopy, Fourier transform infrared, and electrochemical method. Bimetallic Ni0.75Co0.25-MOFs modified carbon paste sensor displayed the optimum sensing performance for the electrochemical detection of paracetamol. A linear response over the range 6.00 × 10- 7 to 1.00 × 10- 4 M with a detection limit of 2.10 × 10- 8 M was obtained. The proposed method was applied to detect paracetamol in spiked human plasma and to determine paracetamol in the presence of its major toxic impurity, p-aminophenol. These findings suggest the considerable potential use of the newly developed sensor as a point-of-care tool for detecting paracetamol and p-aminophenol in the future.

Development of a dual-template molecularly imprinted electrochemical sensor for the simultaneous detection of depression markers 5-HT and Glu.

A dual-template molecularly imprinted electrochemical sensor was developed for the simultaneous detection of serotonin (5-HT) and glutamate (Glu). First, amino-functionalized reduced graphene oxide (NRGO) was used as the modification material of a GCE to increase its electrical conductivity and specific surface area, using Glu and 5-HT as dual-template molecules and o-phenylenediamine (OPD) with self-polymerization ability as functional monomers. Through self-assembly and electropolymerization, dual-template molecularly imprinted polymers were formed on the electrode. After removing the templates, the specific recognition binding sites were exposed. The amount of NRGO, polymerization parameters, and elution parameters were further optimized to construct a dual-template molecularly imprinted electrochemical sensor, which can specifically recognize double-target molecules Glu and 5-HT. The differential pulse voltammetry (DPV) technique was used to achieve simultaneous detection of Glu and 5-HT based on their distinct electrochemical activities under specific conditions. The sensor showed a good linear relationship for Glu and 5-HT in the range 1 ~ 100 µM, and the detection limits were 0.067 µM and 0.047 µM (S/N = 3), respectively. The sensor has good reproducibility, repeatability, and selectivity. It was successfully utilized to simultaneously detect Glu and 5-HT in mouse serum, offering a more dependable foundation for objectively diagnosing and early warning of depression. Additionally, the double signal sensing strategy also provides a new approach for the simultaneous detection of both electroactive and non-electroactive substances.